Page 1
INSTRUCTION MANUAL
Model Number: GT42395
GREAT FOR QUICKLY TRACKING AND
LOCATING PEOPLE, PETS AND VEHICLES
GPS TRACKER
Page 2
2
Safety Warnings & Cautions
1. Carefully read all safety instructions and the user manual before operation.
2. Keep the GPS Tracker away from liquid.
3. Do not expose or immerse the GPS Tracker in liquid.
4. Keep away from heat sources such as heaters and ovens
5. Never add any attachments and/or equipment without the approval of the manufacturer.
Unauthorized modications may result in re, electric shock or other personal injury and may
void your warranty.
6. Do not drop or jar the GPS Tracker. Dropping or rough use of the GPS Tracker will cause damage.
7. Do not place near strong magnets or strong electric currents.
8. Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
Cocoon GPS tracker has been tested and meets applicable limits for Radio Frequency (RF) exposure.
Specic Absorption Rate (SAR) refers to the rate at which the body absorbs RF energy. SAR exposure
is limited at 1.6 Watts per Kilogram (over a volume containing a mass of 1 gram of tissue) in Australia.
During testing, the Cocoon GPS tracker is set to the highest transmission level and placed in
positions to simulate use near the body, with 10mm separation.
Carry the Cocoon GPS tracker at least 10mm away from your body to ensure exposure levels remain
at or below the as-tested levels. Cases with metal parts may change the RF performance of the
device, including conformance with RF exposure guidelines, in a manner that has not been tested
or certied.
Although this device has been tested to determine SAR in each band of operation, not all bands are
available in all areas. Bands are dependent on your service provider’s wireless and roaming networks.
Mobile data may be required for some features such as viewing the Tracker via Google Maps.
The supplier is not responsible for any charges incurred.
In the case of improper usage or if you have opened, altered and repaired the product yourself, all
guarantees are void.
The supplier does not accept responsibility for additional or consequential damage other than
covered by legal product responsibility.
The supplier is not responsible for the end use of this product including any improper use or when
used for purposes that are not specied.
Page 3
3
Safety Instructions.............................................................................................................................................
1. Getting Started
- Package Contents...........................................................................................................................................
- Product Overview...........................................................................................................................................
- LED Light Status..............................................................................................................................................
- Charging the GPS Tracker............................................................................................................................
- Powering On / O the Cocoon GPS Tracker..........................................................................................
2. Functions
- Setting Authorized Numbers...................................................................................................................
- Removing an Authorized Number...........................................................................................................
- Reset to Factory Settings.............................................................................................................................
- Checking the Authorized Numbers & Status of Features................................................................
- Changing the Password...............................................................................................................................
- Setting the Time Zone..................................................................................................................................
- Naming the GPS Tracker..............................................................................................................................
- Locating the GPS Tracker with Latitude and Longitude..................................................................
- Locating the GPS Tracker with Google Maps ......................................................................................
- Locating the GPS Tracker with GPRS Address......................................................................................
- Obtaining the IMEI & Version Numbers.................................................................................................
- Setting up a Geo-Fence Alarm..................................................................................................................
- Turning o a Geo-Fence Alarm.................................................................................................................
- Setting a Speed Alert...................................................................................................................................
- Setting up GPS Signal Loss Alert..............................................................................................................
- Movement Alert.............................................................................................................................................
- Using the SMS Button..................................................................................................................................
3. Web Tracking
- Navigating the Map......................................................................................................................................
- Registering the GPS......................................................................................................................................
- Changing Settings.........................................................................................................................................
- Setting a Point of Interest...........................................................................................................................
- Adding a New Geo-Fence Online.............................................................................................................
- Modifying/Deleting an existing Geo-Fence Online...........................................................................
- History................................................................................................................................................................
- Reports...............................................................................................................................................................
- Latitude and Longitude Values on the Map.........................................................................................
- Ruler....................................................................................................................................................................
- Chart...................................................................................................................................................................
- Adding a New Tracker...................................................................................................................................
- Deleting / Modifying an Existing Tracker...............................................................................................
- Email Settings..................................................................................................................................................
- Change Password...........................................................................................................................................
- Firmware Upgrade.........................................................................................................................................
4. Understanding The Buttons / Commonly Used Abbreviations.......................................................
5. FAQ’s.......................................................................................................................................................................
6. SMS Commands................................................................................................................................................
7. Support / Warranty Details............................................................................................................................
Contents
i
4
4
5
6
6
7
7
8
8
8
9
9
9
10
10
10
11
12
12
12
13
13
14
14
15
15
16
17
17
17
18
18
18
19
19
20
20
20
21
22-23
24-25
26
Page 4
4
1. Getting Started
Introduction
Thank your for purchasing the Cocoon GPS Tracker. We trust you will get many years
of carefree and reliable use out of this product. Please read and follow the user
manual before rst use. If you experience any diculties setting up or using this
product, please see back page for contact details:
Package Contents
1. Cocoon GPS Tracker Unit
2. Rechargeable battery
3. Charging Cable
4. Charging Adaptor
5. Weather Resistant Case
6. User Manual
7. Getting Started Guide
8. Warranty Card
9. Warranty Stickers
Product Overview
FRONT VIEW
223
3
1
4
4
5
5
1. GSM LED
2. GPS LED
3. CHARGE LED
TOP VIEW
4. Power Button
LEFT SIDE
5. SMS Button
Page 5
5
LED Light Status
GREEN LED - GSM
Quick ash(0.2 seconds on and 2.8 seconds o) GPS Tracker is connected to GSM network
Flashing (1 second on and 2 seconds o) GPS Tracker is not connected to GSM network
Solid No SIM Card inserted
BLUE LED - GPS
Quick ash (0.2 seconds on and 2.8 seconds o) GPS Tracker has a GPS x
Flashing (1 second on and 2 seconds o) GPS Tracker has GSM positioning x
Long ash (2 seconds on and 1 second o) GPS Tracker has no GPS x
RED LED
Solid GPS Tracker is Charging
O GPS Tracker is fully charged or not charging
Flashing Device is in motion
6
7
9
RIGHT SIDE
6. USB Charging Port
BACK SIDE
7. Back Cover
8. Battery Compartment
9. SIM Card Slot
8
Page 6
6
Charging the GPS Tracker
1. Open the back cover of the GPS Tracker
2. Insert the battery into the GPS Tracker
3. Connect the USB cable to the GPS Tracker
4. Connect the other end of the USB cable to your computer or included
charging adaptor
NOTE: Charge the GPS Tracker for a minimum of 4 hours before rst
use to maximise the battery life
Powering On / O the Cocoon GPS Tracker
1. Hold the Power button on the top of the unit for 5 seconds to turn the
GPS tracker on
2. The GSM & GPS lights will TURN ON to indicate the GPS Tracker is on
3. Hold the Power button on the top of the unit for 5 seconds to turn the
GPS tracker o
4. The Power button will fade to indicate the GPS is turned o
Page 7
7
2. Advanced SMS functions
Important: When using SMS commands please ensure there are no spaces in the
text and that all letters are in CAPITALS unless otherwise stated.
Note: The default password is 123456. It is recommended that you change
this password.
Setting Authorized Numbers
The Cocoon GPS Tracker allows up 3 phone numbers to send and receive commands.
Follow the steps below to authorize a phone number.
1. From the mobile you would like to authorize, SMS [PASSWORD]+[A/B/C]+1
For example if your password is 123456 and you would like to authorize
mobile number 1, you would SMS 123456A1 to the Cocoon GPS Tracker
2. If you would like to set a second or third authorized number simply
change the letter of the command
For example, if your password is 123456 and you would like to authorise
mobile number 2, you would SMS 123456B1 to the Cocoon GPS Tracker
Removing an Authorized Number
To remove an authorized number from the Cocoon GPS Tracker follow the steps below.
1. From the mobile you would like to unauthorize,
SMS [PASSWORD]+[A/B/C]+0
For example, if your password is 123456 and you would like mobile number
1 to be no longer authorized, you would SMS 123456A0 to the Cocoon
GPS Tracker
2. The phone number you have selected will no longer receive SMS’s from
the GPS Tracker
Page 8
8
Reset to Factory Settings
The Cocoon GPS Tracker can be reset to factory settings by using the following
command. This can be useful if you forget your password.
Warning: All settings, data and preferences will be lost and reset to a default state.
1. To reset the Cocoon GPS Tracker to factory settings SMS RESET!
Note: unlike other SMS commands, no reply will be sent to indicate the
device has accepted the command. The exclamation point must be
included in the command for it to be accepted
Checking the Authorized Numbers & Status of Features
1. To request a list of authorized numbers and the current status of the
Cocoon GPS Tracker, SMS [PASSWORD]+G
For example, if your password is 123456 you would SMS 123456G to the
Cocoon GPS Tracker
2. The device will reply “A[AUTHNUMBER], B[AUTHNUMBER], C
[AUTHNUMBER], Speed: 0,100km/h, GEO:0,0,0, Coord Sv:0, Listen-in:0,
UTC-T:0.0, Motion:0,Movement:0,0, Bat:100”
Changing the password
Note: The default password is 123456. It is recommended that you change this password.
1. To change the password of the Cocoon GPS Tracker, SMS
[PASSWORD]+H+[NEWPASSWORD]
For example, if your password is 123456 and you would like to change it to
987654 you would SMS 123456H987654 to the Cocoon GPS Tracker
2. Make sure the new password is 6 Digits or it will not be recognized
NOTE: Letters and numbers can be used for the password.
Symbols will not be recognized
Page 9
9
Setting the Time Zone
The unit is set to Australian Eastern Standard Time by default.
1. To modify the time zone, SMS [PASSWORD]+L+[+00/-00] to the Cocoon
GPS Tracker
For example, if your password is 123456 and you want Eastern Standard
Time, you would SMS 123456L+10 to the Cocoon GPS Tracker
Naming the GPS Tracker
You can add a name to the Cocoon GPS Tracker to give individualised SMS reports.
This can be useful if you need to distinguish between multiple GPS trackers
1. To attach a unit name to all SMS alerts, SMS [PASSWORD]+U+1,[NAME]
For example if your password is 123456 and you want to name the unit
“John”, you would SMS 123456U1,John to the Cocoon GPS Tracker
2. If successful the device will reply “John UserName set! +GPS info”
Locating the Cocoon GPS Tracker with Latitude and Longitude
Your Cocoon GPS Tracker can send its current location using Latitude and
Longitude; this information can be then entered into mapping software to nd its
current location.
1. To request the Latitude and Longitude Coordinates of the Cocoon GPS
Tracker, SMS [PASSWORD]+F
For example, if your password is 123456 you would SMS 123456F to the
Cocoon GPS Tracker
2. The device will reply “GPS Info!
Date: xx; Time:xx; LAT:xx; LOT:xx; Speed:xx”
3. Using the LAT and LOT values you can locate the device using mapping
software such as Google Earth or Google Maps
Page 10
10
Locating the Cocoon GPS Tracker with Google Maps link
Your Cocoon GPS Tracker can send you an active website link to Google Maps of the
latest GPS coordinates of the device.
1. To request a Google Maps link showing the location of the Cocoon GPS
Tracker SMS [PASSWORD]+FM
For example, if your password is 123456, you would SMS 123456FM to the
Cocoon GPS Tracker
2. The device will reply “http://maps.google.com/mapsxxxx” Open the
link on your mobile device and the location of the Cocoon GPS Tracker
when the SMS was sent, will be displayed
Locating the Cocoon GPS Tracker with GPRS Address
Your Cocoon GPS Tracker can send you the current address location of the GPS unit.
This will be given using the street address of the trackers location.
1. To request the current address of the Cocoon GPS Tracker, SMS
[PASSWORD]+ADD
For example, if your password is 123456, you would SMS 123456ADD to
the Cocoon GPS Tracker
2. The device will reply “LAT: xx; LOT: xx; Add: number street sux,
suburb, state, postcode, country.”
Note: A GPRS signal must be available for this feature to work
Obtaining the IMEI and Version numbers
1. To request the IMEI and version numbers of the Cocoon GPS Tracker,
SMS [PASSWORD]+V
For example, if your password is 123456, you would SMS 123456V to the
Cocoon GPS Tracker
2. The device will reply “Version: Soft:xxxxxxx Hard:xxxxxxx
IMEI:xxxxxxxxxxxxxxx GSM CSQ:xx”
3. This information will be required for Web Tracking applications
Page 11
11
Setting up a Geo-Fence Alarm
A geo-fence is a virtual perimeter for a real world geographic area. A geo-fence
could be set around a neighbourhood, a school’s boundary or a residence. Once a
geo-fence is set up, a notication can be sent to an authorised number when the
GPS tracker enters or exits the predened area.
Note: While you can set up a geo-fence using an SMS, it is recommended you use
the Web service. We recommend only advanced users set up a Geo-Fence using SMS
commands.
1. To set up a geo-fence alarm around current location of the Cocoon GPS
Tracker, send an SMS to the Cocoon GPS Tracker in the following format:
SMS [PASSWORD]+I+(1-3),(0-1),(0-1),(001-999)(M/KM)
For example, if your password is 123456 and you wanted to set geo-fence 1 to be on 100
meters around the GPS trackers’ current location and to send an alarm when the GPS
leaves the geo-fence, you would SMS 123456I1,1,0,100M to the Cocoon GPS Tracker
2. If successful the device will alert you when the unit enters/leaves the
dened geo-fence area
3. You will receive an SMS in the following format: “Geo Alarm!+Geo Info”
Geo Fence number. Value can be 1-3
Distance in Meters/Kilometers
0=Alarm on Entry 1=Alarm on Exit
Page 12
12
Turning o a Geo-Fence Alarm
1. To turn o a previously set up geo-fence alarm, SMS
[PASSWORD]+I+[1-3],0,0 to the Cocoon GPS Tracker
For example, if your password is 123456 and you want to turn o geo-fence
1, you would SMS 123456I1,0,0 to the Cocoon GPS Tracker
Setting a Speed Alert
Your Cocoon GPS can be set to alert you when it exceeds a set speed.
1. To set up a speed alert, SMS [PASSWORD]+J+1+(001-255) to the Cocoon
GPS Tracker
For example if your password is 123456 and you wanted to set a speed limit
of 20km/h you would SMS 123456J1,020
2. The device will send an SMS to the authorized numbers stating
“Over-speed! + GPS-INFO” when the Cocoon GPS Tracker’s recorded
speed exceeds 20km/h
3. To turn o a speed alert, SMS: [PASSWORD] + J+0 to the Cocoon
GPS Tracker
For example, if your password is123456, you would SMS 123456J0 to
the Cocoon GPS Tracker
Setting up GPS Signal Loss Alert
This function lets the Cocoon GPS Tracker automatically send the last known GPS info
to all authorized numbers when it enters an area without a GPS signal.
1. To set up a GPS signal loss alert, SMS [PASSWORD]+K+1
For example, if your password is 123456 you would SMS 123456K1 to the
Cocoon GPS Tracker
2. The device will send “Before +GPS info” to the preset numbers, when GPS
signal is lost
3. To turn o this function, SMS [PASSWORD]+K+0
For example if your password is 123456 you would SMS 123456K0 to the
Cocoon GPS Tracker
Page 13
13
Movement Alert
This function will send an SMS to the authorized numbers if the GPS unit moves a
certain distance away from its location when the command is given.
1. To set up a Movement Alert SMS [PASSWORD]+R+1,xxxM/KM
For example, if your password is 123456 and you would like to be alerted
if the unit moves more than 100 meters from its current location, you would
SMS 123456R1,100M to the Cocoon GPS Tracker
Note: the set distance must be submitted in a three digit format.
For example; To set a 15m alert, you would SMS 123456R1,015M
To set a 1km alert, you would SMS123456R1,001KM
2. To turn o this function, SMS [PASSWORD]+R+0
For example if your password is 123456, you would SMS 123456R0 to the
Cocoon GPS Tracker
Using the SMS Button
The SMS button will send an SMS to all registered mobiles with the current
coordinates of the GPS tracker.
1. Press the SMS button for 3 seconds
2. The GSM light will dim and the Cocoon GPS Tracker will send an
SMS to all registered numbers stating “Help me! +GPS Info” with the
current coordinates of the GPS Tracker
3. Web Tracking
NOTE: To use the online functions you will need the IMEI & Version Numbers
associated with your device. Please see “Obtaining the IMEI and version numbers” on
page 10 of this instruction manual
Using your PC or Mac web browser go to www.gpsmaptracker.com and enter the
username and password provided on the back of your instruction manual and press
the login button.
Page 14
14
Navigating the Map- Computer Mouse
Registering the Cocoon GPS Device
1. Click on “Manage” from the menu located on the left side of the webpage
2. Click “Tracker Info”
3. Click on the “Add New Tracker” button and ll in the name, tracker icon,
hard version, IMEI, user ID and Tracker SIM number elds
4. Click the “Add” button
5. You will be returned to the tracker info screen which you can close by
clicking the [x] in the top right corner
6. Click “Real Time Tracking” from the menu on the left side of the screen
7. Locate the check box next to the name of the GPS tracker you just added
and ensure there is a tick in the box
8. You should now see the GPS tracker’s live location on the map opposite
LEFT BUTTON
Click and drag to
move the map
MIDDLE BUTTON
Roll to zoom in/out
2
3
Page 15
15
Changing Settings
1. Click on “Settings” from the menu on the left side of the webpage to
open the settings dialogue box
2. From this dialogue box you can change the authorized numbers, change
the interval of data reporting, set a speed alarm, modify the time zone,
set a movement alarm, enable/disable coordinate saving and request a
status SMS
Warning: Please do not change any settings if you are unsure what the eect will be
Setting a Point of Interest
Using the web tracker you can set points of interest at any location on the map. This
could include your house, local parks or any nearby areas you wish to keep visible on
your map.
1. Clicking “Interest Point” from the menu on the left side of the webpage
will drop a blue call out on the map
2. This call out can be clicked and dragged to another area of the map.
3. You can also input text to name the point of interest
6
7
Page 16
16
Adding a new Geo-Fence - Online
A geo-fence is a virtual perimeter for a real world geographic area. A geo-fence
could be set around a neighbourhood, a school’s boundary or a residence. Once a
geo-fence is set up, a notication can be sent to an authorised number when the
GPS tracker enters or exits the predened area.
1. To set up a geo-fence, select “Geo-Fence” from the menu on the left side
of the webpage
2. Click “Add New Geo-Fence”
3. Enter a name for the geo-fence you want to create
4. Click the “Select range from map” button
5. The dialogue box will disappear and the map will be visible again
6. Find the area you want to set up a geo-fence around – see navigating
the map, page 14
7. Left click on the map to set the rst corner of the geo-fence
8. Move the mouse and click a second time to set the opposite corner.
Don’t worry about trying to set the area perfectly the rst time, you can
ne tune the area later
9. You will now see a green rectangle with a red line outline and white
squares along the edges. The red line is the border of the new geo-fence
10. You can change the geo-fence by clicking and dragging one of the
white squares to a new location. By doing this you can ne tune the
borders of the geo-fence to t any area you like
11. While re-sizing you may notice transparent squares along the border,
these are additional points you can add, by clicking and dragging, that
allow further control over the geo-fence area
12. When you are happy with the area set click the “Ok” button on the
“Finish GEO editing?” dialogue box to return to the “Add New
Geo-Fence” menu
13. You can now change the alarm to either send an alert when the Cocoon
GPS tracker enters the geo-fence or when it leaves
14. Click the “Submit” button. The geo-fence is now active
Page 17
17
Modifying/Deleting an existing Geo-Fence - Online
1. Select “Geo-Fence” from the left side menu to open up the geo-fence
dialogue box
2. In the “Operation” column click on the green modify text to open the
“Edit Geo-Fence” dialogue box
3. Modify the elds required then click the “Submit” button
4. In the “Operation” column click on the green “delete” text
5. Click the “OK” button when prompted to delete the geo-fence entirely
Note: This will remove the geo-fence and cannot be restored.
History
View the GPS Tracker’s recorded location for the past 3 months in 7 day blocks.
1. Select “History” from the left side menu to expand the History menu
2. Set a start and end date
3. Click the “Search” button
Note: The search period cannot be more than 7 days long
4. When you hit “search” the web tool will return every GPS point reported
within the specied time frame.
Note: Each point is recorded separately (usually at 30 second increments)
and can be viewed as an individual point
5. You can click the “Play” button to chronologically cycle through the
recorded points. Use the “-“ and “+” buttons to change the cycle speed
6. You can manually navigate the list of GPS points by clicking “Previous”
and “Next”
7. Clicking “Save to XML le” will save the le in a format that can be
used with various applications and Web services
Reports
1. Select “Reports” from the left side menu to expand the Reports menu
2. Set a start and end date
3. Click the “Search” button
Note: The search period cannot be more than 7 days long
Page 18
18
4. A lter can be applied via the drop down menu if a certain type of data
is required
5. When you hit “search” the web tool will return every GPS point reported
within the specied time frame
6. From the “Reports” dialogue box you can choose to export the data to
an .xls format by clicking “Export Excel” at the bottom of the report
Using Latitude and Longitude Values on the Map
You can manual input any latitude and longitude values on the map navigate to that
given area.
1. Select “Map” from the left side menu to expand the Map menu
2. Enter a pair of Latitude and Longitude coordinates
3. Click the “Locate” button
4. This will put a red pin on that location and zoom to it using the map
Ruler
Utilising the map you can measure between any points selected.
1. Select “Ruler” from the left side menu to select the ruler tool
2. While the mouse is over the map, left click to set the start point of
the measurement
3. Click the left mouse button again to add another point of measurement
4. Right click to set the end point
5. When set the total length between the two or more points is displayed
in kilometres
Chart
1. Select “Chart” from the left side menu to open the Chart screen
2. Select the Chart Type and time interval from the drop down menus
3. Set the start and end dates
Note: The chart period must be more than two and less than twelve days
4. Click “OK” to generate the chart for the period selected
Page 19
19
Manage
Adding a New Tracker
1. Click on “Manage” from the menu of the left side of the webpage
2. Click “Tracker Info”
3. Click on the “Add New Tracker” button
4. Fill in the name, tracker icon, hard version, IMEI, User ID and Tracker
SIM number elds
5. Click the “Add” button
6. You can repeat the steps to add another GPS tracker to the same
account if you choose
Deleting an Existing Tracker
1. Click on “Manage” from the menu of the left side of the webpage
2. Click “Tracker Info”
3. Select the Tracker you wish to delete by checking the box next to
its name
4. Click the “Delete” button
5. You will be prompted to conrm your choice
Warning: Deleting the tracker will remove all data (history, geo-fences etc.)
related to the device
Modifying an Existing Tracker
1. Select “Manage” from the left side menu to open the Tracker
info window
2. Click “Tracker info”
3. Select the Tracker you wish to modify by checking the box next to
its name
4. Click the “Modify” button
5. Now you can modify the GPS Tracker details
Page 20
20
Email Settings
You can set your device to send you email alert settings as well as SMS
1. Select “Manage” from the left side menu to open the email
settings screen
2. Click “Email Settings”
3. Check the box marked “Send email Alert”
4. Fill in the information as given by your email provider then click the
“Modify” button
5. You will now receive email alerts as well as SMS alerts
Change Password
1. Select “Manage” then “Change Password” from the left side menu
2. Input your old password then you will be required to choose a new
password and conrm it
3. Press the “Submit” and your password will be changed
4. Keep note of your password for your records
Firmware Upgrade
Note: This section is for advanced users only; using unauthorized or modied software
with this product may void your warranty
1. Select “Manage” then “Firmware Upgrade” from the left side menu to
open the Firmware Upgrade screen
2. Choose the GPS tracker from the drop down menu and press the
“Read” button to detect the current version of rmware
3. If the version detected is not the latest version, you may need
to update
4. Press the “Choose File” button, navigate to the current rmware le
and select it
5. Press the “Upgrade” button
6. Your device will be updated to the latest available rmware if applicable
Page 21
21
Understanding The Buttons
Power Press and hold for 5 seconds to turn on/o the GPS Tracker
SMS Press for 3 seconds to send SMS’ to all sorted numbers
Commonly Used Abbreviations
GPS INFO :DD-MM-YY Time:HH:MM:SS Lat:000.00000000N
Long:000.00000000E Speed:000.0
GEO INFO Date:DD-MM-YY Time:HH:MM:SS Speed: 000.0
SMS COMMAND Send an SMS to the SIM card inserted in the GPS Tracker
Page 22
22
Problem Solution
The GPS Tracker will not turn on - Hold the power button for 5 seconds
- Charge the GPS Tracker for a minimum of
4 hours
The GPS Tracker is no longer
sending SMS’s
- Check the GPS Tracker has power and
recharge if necessary
- Check the mobile SIM has enough credit to
send SMS’s
How long do I need to charge the
GPS Tracker
Charge at least four hours before the rst use,
typically around 3 hours from completely at
How long does the GPS tracker
battery last per charge?
The battery should last about 100 hours
in standby mode. Keep in mind the unit
consumes more power when sending or
receiving SMS commands
How many phone numbers can I
authorize on the GPS tracker?
The Cocoon GPS Tracker can have up to three
authorized phone numbers at any one time
How do I view a map on my
smart-phone with the current GPS
location?
Request an SMS with Google maps link
(see page 10), then click the link in the SMS
you receive back
What is a Geo-Fence and what do I
do with it?
A geo-fence is a virtual perimeter or barrier.
You can set up a geo-fence for any location
and monitor when the GPS tracker leaves or
enters that location. For example; You could
use a geo-fence to alert you if your pet leaves
your property, or you could set up a
geo-fence around your child’s school to alert
you when they arrive
How do I stop receiving SMS’s from
the GPS Tracker?
Follow the steps for removing an authorized
number on page 7
FAQ’S
Page 23
23
Which device pays for the texts, my
mobile or the GPS Tracker?
When you SMS the GPS Tracker your mobile
is charged for the text. When you receive a
text from the GPS Tracker, the GPS Tracker is
charged for the text
How do I know if the GPS tracker is
out of credit?
The Cocoon GPS Tracker will not be able to
send replies to you SMS commands if it is out
of credit. Please refer to your service provider
for account balance
Why is my GPS tracker sending me
SMS’s every 30 seconds?
‘Frequent SMS’s can be due to any of the
following reasons:
speed alert is set up for a low speed
-turn o speed alerts (see page 12)
Geo-fence alert is set up in a frequented area
-turn o geo fence alerts (see page 12)
Signal loss is set up in a poor reception area
-turn o signal loss alert (see page 12)
Page 24
24
Summary of SMS Commands
Note: Ensure there are no spaces in the texts and that all letters in CAPITALS unless
otherwise stated
The phrase PASSWORD should be substituted with your own password.
The default password is 123456 as used in the example below
SUMMARY OF SMS COMMANDS
Function Command Comment
Set Authorized Number A 123456A1
Set Authorized Number B 123456B1
Set Authorized Number c 123456C1
Remove Authorized Number A123456A0
Remove Authorized Number B123456B0
Remove Authorized Number C123456C0
Check Authorized Numbers 123456G
Change the password 123456HXXXXXX Password must be 6 digits
where XXXXXX is the new
password
Set Time Zone +/- is GMT/UTC time
Australian Eastern Standard
Time
123456L+10 Time zone = +10 UTC
Australian Eastern Daylight
Time
123456L+11 Time zone = +11 UTC
Western Standard Time 123456L+08 Time zone = +08 UTC
Page 25
25
SUMMARY OF SMS COMMANDS
Function Command Comment
Western Daylight Time 123456+09 Time zone = +09 UTC
Add name to SMS alerts 123456U1,John Name can be lower case
Request LAT + LONG
Coordinates
123456F
Request Coordinates with
Google Maps Link
123456FM
Request Coordinates +
Address
123456ADD GPRS signal must be
Available
Request IMEI + Version
numbers
123456V Required for Web Tracking
Set geo-fence alarm 123456I111200M See Instruction Manual
Turn o geo-fence alarm 123456I100 See Instruction Manual
Set Speed Alert 123456J1,020 Last 3 digits denote speed
in km/h
Set Signal Loss Alert 123456K1
Turn o Signal Loss Alert 123456K0
Turn o the LEDs 123456Y0
Turn o device 123456D
Page 26
26
Support
For additional support including helpful guides and videos, visit the Cocoon support
website at www.winplus.com.au/cocoon.html
Telephone: 1300 663 907
Email: customercare@winplus.com.au
Website: www.winplus.com.au
Warranty Details
This product is warranted against defects for a period of One year If the product is
faulty, Winplus will repair or replace the product (at its discretion) at no cost to you
provided the product has been used in accordance with instructions provided. You
are responsible for any expenses associated with making a claim under this warranty
(incl. postage).The benets under our Warranty are in addition to other rights and
remedies under consumer law in relation to these goods. Our goods come with
guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Winplus Australasia Pty Ltd
PO Box 537
Bayswater Business Centre Vic 3153
03 8727 7600
Page 27
27
Notes:
Page 28
28
Loading...