Cocoon FPV HD Camera Drone Instruction Manual

INSTRUCTION MANUAL

Model Number: HE180101

Version 1.3

Warranty Note

If you experience any issues with this product or its
performance is not what you had expected, please contact
us at Winplus Australasia before returning the item to the
store.

It is likely that we can resolve any problems for you via
phone or email.

Important

Getting the most out of your Cocoon FPV HD Camera Drone:

Read the manual carefully

It will help you set up with ease

Visit www.cocoonproducts.com.au

We have additional support videos and guides

Call After Sales Support - 1300 663 907

Email [e-mail]

We’re always happy to help

Warranty Note

Warranty Details

The product is guaranteed to be free from defects in workmanship and parts for a period
of 12 months from the date of purchase. Defects that occur within this warranty period, under
normal use and care, will be repaired, replaced or refunded at our discretion. The benets
conferred by this warranty are in addition to all rights and remedies in respect of the product
that the consumer has under the Competition and Consumer Act 2010 and similar state and
territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

AFTER SALES SUPPORT

MODEL: HE180101 PRODUCT CODE: 62999 09/2018

REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

1300 663 907

AUS

[e-mail]

YEAR WARRANTY

1

FPV HD CAMERA DRONE

Warranty Details

The product is guaranteed to be free from defects in workmanship and parts for a period
of 12 months from the date of purchase. Defects that occur within this warranty period, under
normal use and care, will be repaired, replaced or refunded at our discretion. The benets
conferred by this warranty are in addition to all rights and remedies in respect of the product
that the consumer has under the Competition and Consumer Act 2010 and similar state and
territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

AFTER SALES SUPPORT

MODEL: HE180101 PRODUCT CODE: 62999 09/2018

REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

1300 663 907

AUS

[e-mail]

YEAR WARRANTY

1

FPV HD CAMERA DRONE

Warranty Details

6

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

Safety Instructions

Follow all instructions and take notice of all warnings to reduce risk of re or electric shock.

• Read the instructions in this manual thoroughly before operating your Cocoon FPV HD Camera

Drone

• This drone must be operated safely at all times. It is the operator’s responsibility to always y in

safe conditions

• Always check each component of the drone is operating correctly before ying

• Always follow local aviation rules and regulations when ying the drone

• This drone is designed for ages 14+

• Adult supervision is always advisable with any form of ying

• Always ensure your ight area is safe

• Always keep the drone in direct line of sight

• Do not immerse the drone, batteries nor the remote control in water

• If a problem occurs with the drone, always contact the supplier before attempting to y again

• Do not y in windy, rainy or low light conditions

• Non-rechargeable batteries are not to be recharged

• Rechargeable batteries are to be removed from the drone before being charged

• Rechargeable batteries are only to be charged under adult supervision

• Exhausted batteries are to be removed from the drone

• Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according

to the instructions

• The supply terminals are not to be short-circuited

• Do not leave drone or batteries near a heat source such as re or heater or in direct sunlight

• Keep the drone and batteries in a cool dry place

• Only use the provided USB charging cable to recharge the rechargeable battery

• The USB charging cable is for indoor use only

• If the device is exposed to sudden changes in temperature, for example when taken from the

cold into a warm room, wait at least two hours before operating the drone

1300 663 907

7

After Sales Support

Model Number HE180101

[e-mail]

Warnings

• This drone is not a toy and can cause severe damage or injury if used incorrectly. If you have

never own a drone before, read the full manual before attempting to y

• Propellers are hazardous moving parts, when they are operational keep ngers and other body

parts away from them

• Incorrect operation of the drone may result in severe injury, loss of property or nes. Winplus

Australasia does not take any responsibility if local rules and regulations are not followed

• Winplus Australasia does not take any responsibility for the loss of the Cocoon FPV HD

Camera Drone and it is NOT covered by warranty. We recommend that users test their drone

in a safe indoor environment before attempting to y the drone outdoors

• Do not attempt to repair, open or alter any components. In the case of improper usage or if you

have opened, altered or repaired the product yourself, all warranties and guarantees are void.

Battery Care and Storage

How to Maintain Lithium Battery

• Charge new batteries following the charging instructions

• Only use the provided USB charging cable to recharge the rechargeable battery

• Avoid frequently over charging

• Avoid touch metal contacts

• Avoid using often in high or low temperature environments.

• Avoid long periods without using or recharging.

• Avoid using lithium ion batteries which are hot after being fully charged.

Battery Storage

• Charge or discharge the battery to approximately 50% of capacity before storage.

• Charge the battery to approximately 50% of capacity at least once every six months.

• Remove the battery and store it separately from the product. Store the battery at temperatures

between 5 °C and 20 °C.

NOTE: The battery self-discharges during storage. Higher temperatures (above 35 °C) reduce the
battery storage life.

8

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

Rules & Regulations

The following regulations must be followed when operating a camera drone or quadcopter in

Australia.

• You must only y during the day and keep your drone within visual line-of-sight. This means

being able to see the aircraft with your own eyes (rather than through a device) at all times.

• You must not y over or above people. This could include beaches, parks, events, or sport ovals

where there is a game in progress.

• You must keep your drone at least 30 metres away from other people.

• You must not y your drone higher than 120 metres (400ft) above the ground.

• You must not y your drone over or near an area aecting public safety or where emergency

operations are underway (without prior approval). This could include situations such as a car

crash, police operations, a re and associated reghting eorts, and search and rescue.

• You must only y one drone at a time.

• If your drone weighs more than 100g, you must keep at least 5.5km away from controlled

aerodromes. Flying within 5.5km of a noncontrolled aerodrome or helicopter landing site

(HLS) is possible, but only if no manned aircraft are operating to or from the aerodrome. If

you become aware of manned aircraft operating to or from the aerodrome/HLS, you must

manoeuvre away from the aircraft and land as soon as safely possible.

• It is illegal to y for money or economic reward unless you have a drone operators certicate, or

you are ying an excluded drone in the sub-2kg or private landholder category.

• Remember, you must not operate your drone in a way that creates a hazard to another aircraft,

person or property.

• Respect personal privacy. Don’t record or photograph people without their consent — this may

breach state laws.

Source: http://www.casa.gov.au/modelaircraft

It is the quadcopter operator’s responsibility to regularly check the current rules
and regulations.

1300 663 907

9

After Sales Support

Model Number HE180101

[e-mail]

Disposal

At the end of its working life, do not throw this product out with your household rubbish. Electrical

and electronic products contain substances that can have a detrimental eect on the environment

and human health if disposed of inappropriately

Observe any local regulations regarding the disposal of electrical consumer goods and dispose of

it appropriately for recycling. Contact your local authorities for advice on recycling facilities in your

area. Observe and local regulations regarding the disposal of waste products. Contact your local

authorities for advise on recycling facilities in your area

Please keep the original packaging carton and materials in a safe place. It will help to prevent any

damage if the product needs to be transported in the future. In the event it is to be disposed of,

please recycle all packaging material where possible. If you require another copy of this instruction

manual, please contact [e-mail] to obtain an electronic copy

Maintenance and Storage

The maintenance of drone should be conducted by skilled person only. Always unplug the battery

before doing maintenance. Please follow below safety/deterioration checks during maintenance:

• Check the conditions of Drone Body, Propeller Guards, Landing Gear and Propellers to ensure

they are intact

• Check the condition of Battery to ensure it is intact

• Check conditions of all screws to ensure they are screwed tight

• Check conditions of the wiring to ensure nothing is pinched of damaged

The drone does not require scheduled cleaning. Should cleaning be necessary, simply wipe the

outside surface with a dry soft cloth.

Always store your device in a clean dry environment and avoid storage in extreme heat or cold.

10

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

Contents

Warranty Note 3

Warranty Details 5

Safety Instructions 6

Warnings 7

Battery Care and Storage 7

Rules & Regulations 8

Disposal 9

Maintenance and Storage 9

Parts List 11

Features 11

Technical Specications 11

Product Overview 12

1.1 Cocoon FPV HD Camera Drone 12

1.2 Remote Control 13

Setup & Installation 14

2.1 Installing the Remote Control Batteries 14

2.2 Charging & installing the Cocoon FPV HD Camera Drone Battery 14

2.3 Install the Camera and Propeller Guards 15

2.4 Installing the Phone Holder to use your Smartphone 15

Operation 16

3.1 Turning ON and Pairing the Remote Control with the Drone 16

3.2 Switching OFF the Propellers & Drone 17

3.3 Flying the Cocoon FPV HD Camera Drone 18

3.4 Fine Tuning / Trimming 19

3.5 Level Calibration 20

3.6 Speed Control 20

3.7 360° Flip Stunt Feature 20

3.8 Hovering Height Adjustment 21

3.9 Headless / Normal Modes 21

3.10 Recalibrate the Cocoon FPV HD Camera Drone 22

3.11 Capture Photos & Videos 22

3.12 Replacing Parts 22

3.13 Fly the Cocoon FPV HD Camera Drone using the ‘Drone Go’ App 23

Operation 24

3.14 ‘Drone Go’ Application Interface 24

FAQs 25

Repair and Refurbished Goods or Parts Notice 26

1300 663 907

11

After Sales Support

Model Number HE180101

[e-mail]

Parts List

Technical Specications

Features

1x Cocoon FPV HD
Camera Drone
1x 2.4GHz Remote Control
1x USB Charging Cable
1x Rechargeable Battery
1x Phone Mount
1x Screwdriver
1x Detachable HD 720P
Camera
4x AA Activ Energy Batteries
4x Propeller Guards

4x Landing Skids
(On the drone)

4x Spare Blades
1x Instruction Manual
(Not shown)
1x Getting Started Guide
(Not shown)
1x Warranty Card (Not shown)
1 x Flight Safety Card
(Not shown)

Rechargeable battery for drone: 3.7V DC 500mA Lithium Battery

Charging time: Approx. 130 minutes

USB charger input: 5V DC

Fly time: Up to 8 mins per charge depending on usage*

Frequency: 2.4GHz

Gyro: 6 Axis

Battery for remote control: 4 X AA batteries (included)

Control distance with remote control: Up to 45 meters

+

Control distance with smart phone: Up to 25 meters

+

*

NOTE: Flight times will vary depending on proper care of the batter and ight conditions

+

NOTE: Strong magnetic elds could reduce working distance

• High Denition (720P) camera records high quality video & photos

• FPV (First Person View) wireless transmission to iOS or Android smartphone*

• Hover feature and headless mode

• Light yet robust construction

• 360 degree built-in ip stunt feature

• 4 channel 2.4GHz remote control

• 6-Axis gyroscope for stability

*App Control support types

iOS 8.0 , Android 4.1

12

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

21

4 5 6

3

Product Overview

1.1 Cocoon FPV HD Camera Drone

1. Propeller

2. ON/OFF Button

3. Propeller Guard

4. Landing Skid

5. Camera/MicroSD Card

Slot (Rear)

6. Battery (Behind)

*Illustration shows front/

head of drone

NOTE: MicroSD Card not included. Maximum card capacity 32GB

1300 663 907

13

After Sales Support

Model Number HE180101

[e-mail]

1.2 Remote Control

1. Phone Holder

2. ON/OFF Button

3. Left Thumb Stick - Fly Up/

Down, Turn Left/Right,

Depress for Fine Tuning,

4. Right Thumb Stick -

Headless mode, Slow/

Fast Speed Control, Fly

Forwards/Backwards,

Sideways Flying

5. Photo

6. Video

7. 360º Flip Stunt

8. B Button - Short press for

auto take o and landing

1

2

3

5 7

6 8

4

Product Overview

14

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

Setup & Installation

2.1 Installing the Remote Control Batteries

a. Use a screw driver to remove the screw on the back of the remote control, then open the

battery cover

b. Install the 4 x AA supplied batteries into the back of the remote control. Please note the

polarity positions indicated

c. Replace the cover and reinstall the screw

NOTE: For best performance, do not mix dierent types of batteries.

2.2 Charging & installing the Cocoon FPV HD Camera Drone Battery

a. Fully charge the drone’s battery before use

b. Insert the battery power port into the small end of the

supplied USB charging cable

c. Insert the other end of the USB charging cable into a USB port

(charger not included). The charging indicator light will be

RED

d. Once the charging indicator has turned OFF and no longer

red, the battery is fully charged

e. Disconnect the USB cable from the USB port

f. Disconnect the battery power port from the small end of the

USB charging cable

g. Insert the battery into Cocoon FPV HD Camera Drone

ensuring a tight t

NOTE: See page 6 for further information about battery care

.

1300 663 907

15

After Sales Support

Model Number HE180101

[e-mail]

Setup & Installation

2.3 Install the Camera and Propeller Guards

a. Connect the camera wires to the plug port located on the base of the drone. Coil any

remaining cable into the cavity

b. Insert the camera into the base of drone by twisting the camera 90 degrees into place until you

feel a ‘click’ and some resistance

c. Push the propeller guard into the slot and push the lever down until you hear a ‘click’

NOTE:

• Ensure the camera is facing the head of the drone as illustrated on page 12. It should be facing away
from the battery if you are looking at the drone’s base

• To remove the camera, twist the camera 90 degrees to the right and unplug the wire

2.4 Installing the Phone Holder to use your Smartphone

If you are only using the remote control to operate the drone, you do not need to install the phone

holder. It is ideal to use the phone holder when you want to use your smartphone to take photos

and videos whilst still using the remote control to y the drone.

To install the phone holder, turn the remote over and:

a. Slide out the cover on the remote control as illustrated

b. Insert the phone holder connector to the top of the remote

control by sliding it down into place

c. Press the ends of the phone holder to open and insert a

smart phone. Release to secure device

d. Ensure the device is secure before proceeding. Winplus

Australasia does not take any responsibility for devices that

fall from the phone holder

e. Press the ends of the phone holder to open & release device

f. To remove the phone holder, press down on the moulded

grooves at the back of the remote control and push up to

release it

16

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

B

Operation

WARNING: Incorrect operation of the Cocoon FPV HD Camera Drone may result in severe injury,

loss of property or nes. Winplus Australasia does not take any responsibility if local rules and

regulations are not followed. Winplus Australasia does not take any responsibility for the loss of

the Cocoon FPV HD Camera Drone and it is NOT covered by warranty.

We recommend that users test their drone in a large, safe indoor environment before attempting

to y the drone outdoors. Do not y above 3 metres until you can accurately and condently

control the Cocoon FPV HD Camera Drone.

3.1 Turning ON and Pairing the Remote Control with the Drone

To commence pairing, make sure you have switched both the remote control and drone ON by

pressing the ON/OFF button on both devices. You will notice the ON/OFF buttons on both devices

will ash red. To pair:

a. Move the left thumb stick up then down. You will hear two beeps

b. The ON/OFF buttons on both devices will then change to solid red once paired

c. The LED lights underneath the drone will also ash. Orange indicates the head of the drone,

while green indicates the tail of the drone

Engaging the Propellers

To start the propellers and y the drone, there are three methods that can be used, however each

operate slightly dierently:

Method 1 - Push the left thumb stick up to the highest point

and then allow the thumb stick to reset to the centre

Method 2 – Move the left and right thumb sticks inwards and

hold for 1-2 seconds as illustrated

Method 3 – Press the B Button. This will start the propellers and

raise the drone automatically o the ground.

1300 663 907

17

After Sales Support

Model Number HE180101

[e-mail]

3.2 Switching OFF the Propellers & Drone

To power down the drone and its propellers, there are three methods that can be used.

Each method is dierent and should be used based on the situation at hand:

Operation

Method 1: Slow Shutdown - Push the left thumb stick down to

the lowest level and hold for approximately 5 seconds until the

drone has landed and powered down. In this method, the drone

will slowly come back to the ground and then the propellers will

power down. Use this function if you do not want the motor and

propellers to cut out immediately

Method 2: Immediate Shut Down - Move the left and right

thumb sticks inwards and hold for 1-2 seconds as illustrated to

immediately shut down the motor and propellers. This method

diers from methods 1 and 3 as the drone will not slowly land,

the propellers will immediately shut o and the drone will fall to

the ground.

NOTE: This method should only be used for emergency landings OR
when the drone is close to the ground (approximately 30cm)

Method 3: Auto-Land – Press the B button on the top of the

remote control to auto-land the drone. Like method 1, the drone

will slowly come back to the ground and the propellers will

power down

NOTE:

• In methods 1 and 3, the propellers will not immediately power down. If the drone is already close to
the ground and you use one of these methods, you may need to use the thumb sticks to direct and
control the drone as necessary until the propellers power down and the drone has landed

• To turn OFF the drone completely, press the ON/OFF button on both the drone and the remote
control

• Never leave your drone unattended while powered ON

B

18

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

3.3 Flying the Cocoon FPV HD Camera Drone

Operation

Hover Up & Down

Push the left thumb stick up or down to move the drone

upwards or downwards

TIP: If you begin to lose control of the drone refer to the three
methods outlined on page 17 to land your drone safely.

Forward & Backward

Push the right thumb stick up or down to move the drone

forwards or backwards.

Fly Sideways

Pull the right thumb stick left or right to move the drone to the

left or right. As illustrated, the drone will tilt in the direction you

would like it to go to

Turn Left & Right

Pull the left thumb stick left or right to turn the drone left or

right.

NOTE: This does not move the drone sideways to the left or right

NOTE:

• If the both the green and orange LEDs begin ashing quickly while you are ying the drone, this
indicates the battery is running low. Land immediately on a level surface and recharge your battery
as explained on page 14. If the battery is extremely low it will land automatically

• Do not y again until the battery is fully charged

1300 663 907

19

After Sales Support

Model Number HE180101

[e-mail]

3.4 Fine Tuning / Trimming

If you nd the drone is veering in a particular direction, you may need to ne tune the control to

keep the Cocoon FPV HD Camera Drone steady. This should only be done when there is no or very

minimal wind.

While the drone is in the air, depress the left thumb stick (i.e. press the left thumbstick into its

centre, don’t move the thumbstick down) and at the same time use the right or left thumb stick as

per the following instructions depending on the direction that needs ne tuning. Do not lift the

left thumb stick until you have nished ne tuning.

Operation

Forward/Backward Fine Tune

Depress the left thumb stick into its centre, move the right

thumb stick up or down

Left/Right Fine Tune

Depress the left thumb stick into its centre, move the right

thumb stick to the left or right

Turn Left/Right Fine Tune

Depress the left thumb stick into its centre, move the left thumb

stick to left or right

NOTE:

• You may need to ne tune your drone multiple times during ight due to air ow conditions

Reset Trimming

In order to reset trimming, land the drone and then turn the remote control OFF. Then whilst

depressing the left thumb stick, turn the remote control ON. The remote control will beep three

times to conrm the trim has been reset.

20

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

Operation

3.5 Level Calibration

This feature allows you to calibrate the drone so that it does not start to tilt during ight.

Calibration should only be done before ight not during ight. To calibrate the drone:

a. Place the drone on a level surface

b. Press the left and right thumb sticks to the lower right corners and

hold for 2-3 seconds. You will notice the drone LED lights will ash

c. The level calibration will now be complete

3.6 Speed Control

The Cocoon FPV HD Camera Drone can be operated in a low and a high-speed setting. When you

turn on the drone, it will automatically be set to low speed. To change to high speed, depress the

right thumb stick in towards its centre, you will hear two beeps. If you are in high speed and want

to move to low speed, depress the right thumb stick again, you will hear one beep.

NOTE:

• You can adjust speed settings while the drone is in ight or while the drone is on the ground and
paired

• The drone’s default setting is low speed. If you change the speed to high and switch OFF the drone, it
will default back to low when you go to turn the drone back ON at a later time. If you however land
the drone without turning the drone OFF, then the drone will still be in high speed

3.7 360° Flip Stunt Feature

Once you are familiar with the basic ight operations, you can explore

the 360° ip stunt feature.

a. Fly the drone to a height of more than 3 metres

b. Press the upper right corner button on the remote control and

simultaneously push the right thumb stick in any direction to

perform the 360-degree ip

NOTE:

• Fully charge the battery before attempting the 360-degree ip. If
the battery power is low, the drone will not be able to perform the
360-degree ip

• Make sure you allow enough space both above and below your
drone before attempting to perform ips

• Never attempt tricks with bent or damaged propellers or guards

3m

1300 663 907

21

After Sales Support

Model Number HE180101

[e-mail]

Operation

3.8 Hovering Height Adjustment

To auto-hover at your desired height, manoevere the drone up and down using the left thumb

stick. At your desired height, simply remove your thumb from the thumbstick and the drone will

auto-hover. You can continue to use the right thumbstick to control the direction of ight, whilst

maintain the hover.

NOTE: Auto-hover will be aected by ying conditions. Fine tune/trim the drone if necessary.

3.9 Headless / Normal Modes

The drone can be operated in Headless and Normal Modes. Headless mode enables you to y the

drone without having to focus on the drone’s orientation i.e. where the head of the drone is in

relation to your position. This means that regardless of whether the head, one of the sides or the

tail of the drone is facing you, moving sideways to the left will always be left for example.

In Normal Mode however, the drone’s direction will be dependent upon the tail of the drone in

relation to your position. For example, if the drone’s tail is facing you and you manoeuvre it the

left, the drone will move left. However, if the head of the drone is facing you and you perform the

same manoeuvre, you will nd the drone will move right.

To change to Headless Mode:

a. During ight, depress the right thumb stick into its centre for approximately 2 seconds until

you hear 8 beeps and the LED lights under the drone will ash every 4 seconds

b. To change to normal mode, depress the right thumb stick into its centre for approximately 2

seconds and you will hear one long beep. In normal mode, the LED lights under the drone will

not ash

NOTE:

• Headless mode is great for beginners

• If you are operating the drone in Normal Mode, we recommend that you always start by having the
drone’s tail facing you therefore the head of the drone and camera should face away from you

• The drone’s default setting will be in Normal Mode. If you change the drone to Headless Mode and
switch OFF the drone, the drone will default back to Normal Mode. If you only land the drone and do
not switch it OFF, it will remain in Headless Mode

• You can switch between Normal and Headless Modes both during ight and after you have paired
the remote control and drone before ying

22

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

Operation

3.10 Recalibrate the Cocoon FPV HD Camera Drone

In the event the drone begins to y strangely OR after a major

impact, you can recalibrate the direction by pushing the left and

right thumb sticks for approximately 2 seconds to the far bottom

left simultaneously. You will notice the drone’s LED lights will ash

indicating the drone has been reset.

NOTE: You cannot recalibrate the drone during ight. It can only be recalibrated while ON and
positioned on the ground. Please make sure the drone’s tail is facing you

3.11 Capture Photos & Videos

Photos and videos can be captured either directly on your mobile device if connected to the FPV

Application (see page 23 Fly the Cocoon FPV HD Camera Drone using the ‘Drone Go’ App) or

using a MicroSD Card (not supplied)

a. To take a photo, press the photo button on top left shoulder button of the remote control as

illustrated on page 13 until you hear one beep

b. To take a video, press the video button located on the bottom

left shoulder button of the remote control (underneath the

photo button) as illustrated on page 13, until you hear two

beeps to indicate recording has started. To end recording,

press the same button until you hear two beeps

NOTE: Make sure you have installed the camera onto the drone. For
installation, refer to page 15

3.12 Replacing Parts

Eventually your propellers will most likely need to be replaced. Do not operate the Cocoon FPV

HD Camera Drone with damaged propellers as you may suddenly lose control of the drone during

ight. Follow the steps below to replace your drone’s propellers:

a. Position the drone on a level, horizontal surface, with the head facing forward as shown below.

b. Determine which propellers need replacing and note the

propeller warning text side (left or right) by checking the top of

the propeller.

c. Using a at head screw driver, lift the cap to unsecure the

propeller

d. Replace the propeller with the same type (left or right), noted

by an “A “ or a “B”symbol

1300 663 907

23

After Sales Support

Model Number HE180101

[e-mail]

e. Screw in the replacement blade rmly

f. When ying the drone after replacing the propellers, gently increase the throttle to check that

the drone will remain stable when ying. If the incorrect propeller type is used, the drone will

be unable to remain level

To purchase additional propellers or parts for your drone, visit www.cocoonproducts.com.au

3.13 Fly the Cocoon FPV HD Camera Drone using the ‘Drone Go’ App

The Cocoon FPV HD Camera Drone can be operated using the remote control and/or a

smartphone. To setup your smart phone:

a. Download the drone application by using a QR code reader application and scanning the below

QR codes or by searching in the App Store or Play Store for ‘Drone Go’

b. Download the application from the App Store or Google Play depending on your device

c. Switch ON both the remote control and drone and pair them as per section 3.1

d. Go to settings on your phone and turn on WiFi. In the WiFi Search list select “FPV_WIFI_****” .

e. Open the app, click the Start icon to enter the control interface.

For more information on the Drone FPV interface, see page 24

NOTE:

• We recommend using the remote control to y the drone whilst using the App for photos, videos and
FPV (First Person Viewing). Only advanced users should y the drone using a mobile device without
the remote control

• A full bar in the WiFi signal icon indicates the strongest possible signal

• If the remote control is ON and paired to the drone, you will not be able to y the drone using your
mobile device. You will only be able to take a photo or video

• To y the drone using your phone, always turn the remote control OFF

• The control distance with your phone is up to 25 meters

Operation

iOS App

(Version 8.0 or later)

Android App

(Version 4.1 or later)

24

After Sales Support

Model Number HE180101

[e-mail]1300 663 907

Operation

3.14 ‘Drone Go’ Application Interface

1

5

9

13 14 15 16 17 18 19 20

11

12

7

86

10

2 3 4

1. Take Photo

2. WiFi Signal

3. Engage/Switch o Propellers

4. Take Video

5. Left Thumbstick

6. Auto Take O

7. Right Thumbstick

8. Fine Tune - Forwards/Backwards

9. Fine Tune - Turn Left/Right

10. Auto Land

11. Fine Tune - Move Sideways Left/Right

12. Hide Toolbar

13. Show/Hide Thumbsticks

14. Level Calibration

15. High/Low Speed Mode

16. Check SD Card (SD Card not included)

/ Phone Memory

17. Gravity Induction Mode - Uses phone

movement to control drone rather than

using thumbsticks

18. Headless Mode

19. Waypoint Mode (see note below)

20. Back

NOTE:

• For information regarding thumbstick use, refer to remote control instructions on page 16

• When ne tuning there is no need to depress the left thumbstick with the App. Simply press the
arrows

• Using the ‘Drone Go’ App allows you to view the camera in real time using First Person View

• The waypoint function allows you to draw a pathway on the right hand side of the application, for
the drone to follow. For example, a straight line, circle or triangle could be drawn which the drone
will follow. Please note that this waypoint function does not use GPS, this means that the drone’s
pathway can be aected by airow and will not be as accurate as a GPS controlled drone.

• If in Normal Mode (i.e. Headless Mode is o), take note of the head of the drone and therefore the
direction the drone will take

1300 663 907

25

After Sales Support

Model Number HE180101

[e-mail]

FAQs

Question Solution

My Cocoon FPV HD Camera Drone didn’t
pair with my remote control

At times the Cocoon FPV HD Camera Drone may
fail to pair with the remote control. Attempt to pair
again, ensuring the drone is resting on a level surface.

My Cocoon FPV HD Camera Drone isn’t
responding

Check that the battery in the Cocoon FPV HD Camera
Drone is still charged. Also check that the remote
control batteries are still charged.

My Cocoon FPV HD Camera Drone is slow
to respond

Ensure that the remote control batteries are still
charged. There may also be interference from a similar
frequency nearby. Try using the Cocoon FPV HD
Camera Drone in a dierent location, away from
other radio controlled devices.

Not ying straight or spinning Follow the steps in ‘Fine Tuning’ to congure the

Cocoon FPV HD Camera Drone correctly. If
unsuccessful, try following the steps in ‘Recalibrate the
Cocoon FPV HD Camera Drone” on page 22.

How do I see photos and pictures on my
phone?

Open the ‘Drone Go’ app > Start >

> or

> Tap photo or video to view

How do I transfer photos to my camera roll
in iOS?

Open the ‘Drone Go’ app > START >

>

or > SELECT > Tap photo or video to transfer

> ADD TO ALBUM

How do I transfer photos or videos to my
computer in iOS?

First transfer photos or videos to your camera roll
using the instructions above, then download to your
computer per your devices instructions.

How do I transfer photos or videos to my
computer in Android?

Connect your Android mobile to your computer.
Navigate to the root > DRONE directory to nd your
photos and videos. Copy them to your computer.

Repair and Refurbished Goods

or Parts Notice

Unfortunately, from time to time, faulty products are manufactured which need to be returned
to the Supplier for repair.

Please be aware that if your product is capable of retaining user-generated data (such asles
stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs
stored on a portable media player, games saved on a games console or les stored on a USB
memory stick) during the process of repair, some or all of your stored data may be lost.

We recommend you save this data elsewhere prior to sending the product for repair.

You should also be aware that rather than repairing goods, we may replace them with
refurbished goods of the same type or use refurbished parts in the repair process.

Please be assured though, refurbished parts or replacements are only used where they
meet ALDI’s stringent quality specications.

If at any time you feel your repair is being handled unsatisfactorily, you may escalate your
complaint. Please telephone us on1300 663 907 or write to us at:

Winplus Australasia

PO Box 537 Bayswater Business Centre, Victoria, Australia

1300 663 907 - Hours: Mon-Fri 8:30am - 6:00pm AEST

[e-mail]

AFTER SALES SUPPORT

1300 663 907

AUS

YEAR WARRANTY

1

MODEL: HE180101 PRODUCT CODE: 62999 09/2018

FPV HD CAMERA DRONE

[e-mail]

Repair and Refur-
bished Goods or
Parts Notice