USER’S MANUAL
version 1.1
English
UCR-4285 UNIVERSAL REMOTE CONTROL
UCR-4285 UNIVERSAL REMOTE CONTROL
Description of buttons
1. Power: On/Off/Stand-by
2. Indicator
3. Device selection
4. Menu
5. Guide
6. Two-digit number entry
7. AV channel selection
8. Enter/OK
9. Navigation/direction buttons
10. Volume higher/lower
11. Mute
12. Return to previous selection
13. Channel higher/lower
14. Teletext shortcut keys
15. Control options for video and audio recordings
and teletext functions
16. Number entry
Attention: The functions ava ila ble on the UCR4285 only work if they were also available on the
original remote control!
2
9
8
7
5
6
4
3
1
12
10
15
14
13
11
16
1
UCR-4285 UNIVERSAL REMOTE CONTROL
2
[1] Press the latch and remove the battery cover. [2] Install 4 batteries. The poles must match the +
and - symbols on the inside of the battery
compartment. Close the cover.
Do not use rechargeable batteries!
UCR-4285 UNIVERSAL REMOTE CONTROL
CONFIGURATION USING THE CODE LIST
[3] Switch on your device manually (or with the
original remote control).
[4] Find the 5-digit code in the code list that
matches the brand of your device.
The codes shown first are the codes used most
often for a particular brand!
Go to [10] if your brand is not in the list!
The TV in the picture is only used as an
example. Follow these instructions for other AV
equipment as well!
3
UCR-4285 UNIVERSAL REMOTE CONTROL
4
3 seconds
[5] Press the device button that you want to
configure (set your television under ‘TV’, your
stereo system under ‘audio’ etc.).
The buttons are not device specific. Thus you
can configure a 2nd TV under a button you do not
use (e.g. ‘SAT’)!
[6] Press and simultaneously. Do not
release them until the indicator has flashed several
times to confirm.
UCR-4285 UNIVERSAL REMOTE CONTROL
[7] Set the code you found in [4]. [8] Point the UCR-4285 at your device. Press the
power button (device should switch off or go to
stand-by). Now check all the other functions.
If the UCR-4285 does not work or does not
work properly: Repeat steps [4-8] and use the next
code!
If none of the codes work, go to [10]!
The indicator flashes to confirm!
5
UCR-4285 UNIVERSAL REMOTE CONTROL
6
CONFIGURATION USING THE SEARCH FUNCTION
[9] Switch on your device manually (or with the
original remote control).
The TV in the picture is only used as an
example. Follow these instructions for other AV
equipment as well!
[10] Press the device button you want to configure
(set your television under the ‘TV’ button).
The buttons are not device specific. Thus you
can configure a 2nd TV under a button you do not
use (e.g. ‘SAT’)!
UCR-4285 UNIVERSAL REMOTE CONTROL
[11] Press and simultaneously. Do not
release them until the indicator has flashed several
times to confirm.
[12] Enter code ‘9 9 1’. The indicator flashes
several times to confirm.
3 seconds
7
UCR-4285 UNIVERSAL REMOTE CONTROL
8
[13] (1) Press the applicable button:
TV (CRT/CD/Plasma): Press ‘1’.
Video (DVD/VCR): Press ‘2’.
Audio (CD/Tuner/Ampl.): Press ‘3’.
Satellite/Cable/Media PC: Press ‘0’.
Press ‘Power’.
[14] (1) Point the UCR-4285 at the device and press
the direction button c. Repeat this until the device
switches off (or goes to stand-by).
(2) Immediately press ‘Enter’.
It may be necessary to repeat this up to 150
times!
Press ‘d’ if you accidentally go too far!
UCR-4285 UNIVERSAL REMOTE CONTROL
CONNECTING TO A COCO RECEIVER
[15] Activate the search mode of the receiver.
The device shown is the AC-300 with
automatic programming!
If the receiver does not have automatic
programming, use house code ‘A’ plus a number
code between 1 and 14 (see ‘Remarks’ and tables
I and II) and continue at step [17]!
[16] (1) Press the device selection button with the
light bulb.
(2) Select the button you wish to assign to the
receiver (button 1 through 0 or red, green, yellow
or blue).
(3) Press ‘CH+’. To confirm, the built-in dimmer
switches on and off two times.
9
UCR-4285 UNIVERSAL REMOTE CONTROL
10
SWITCHING LIGHTS ON/OFF
[17] (1) Press the device selection button with the
light bulb.
[17] (1) Press the device selection button with the
light bulb.
(2) Select the number you assigned to the receiver
in [16] (point 2).
(2) Select the number you assigned to the receiver
in [16] (point 2).
[18] Control your lighting: [18] Control your lighting:
OnOn
: Press ‘CH+’. Off: Press ‘CH-’. Dimming: Press
‘CH+’ 3x: (1) light switches on, (2) light intensity
changes continuously, (3) select desired light
intensity.
The dimmer function only works if the lamp is
connected to a dimmer receiver!
UCR-4285 UNIVERSAL REMOTE CONTROL
Extra functions
Teletext
If your TV is suitable for teletext, you can use several buttons to control the basic functions:
On: Activate Teletext.
Off: Switch off Teletext.
Zoom in: Show the upper half of the page. Press again to see the lower half. Press again to return to
normal format, or (depending on the TV) press the button.
Pause/Stop: Hold the page.
Mix: Shows both Teletext and the normal TV picture. Also use this button for subtitles. On some TVs
the Mix function is activated by pressing the button.
Volume ‘push-through’
• With this function you can adjust the volume of a device (such as your TV) while the UCR-4285 is set to
control another device (e.g. ‘SAT’ mode).
• Activating the push-through function (example: adjusting the TV volume in ‘SAT’ mode):
1- Press ‘SAT’ to select the mode in which you want to control the volume of the TV.
2 Press and simultaneously. Do not release them until the indicator has flashed several times to
confirm.
3- Press ‘9 9 3’. The indicator flashes several times.
4- Press ‘TV’. The indicator flashes several times.
• Cancelling the push-through function:
1 Press and simultaneously. Do not release them until the indicator has flashed several times to
confirm.
2- Press ‘9 9 3’. The indicator flashes several times.
3- Press ‘Vol +’. The indicator flashes several times.
Macros
• This function allows you to execute a series of commands with just the press of a button, while you
would normally have to press several buttons.
11
UCR-4285 UNIVERSAL REMOTE CONTROL
12
• Programming a macro (example: Using the ‘Last’ button to switch from ‘TV’ mode to ‘SAT’ mode and
select channel 801):
1- Press ‘TV’ to select the mode in which you want to execute the macro.
2- Press and simultaneously. Do not release them until the indicator has flashed several times to
confirm.
3- Press ‘9 9 5’. The indicator flashes several times.
4- Press ‘Last’ to select the button you want to assign to the macro.
5- Now press the desired series of commands: ‘TV’, ‘AV’, ‘SAT’, ‘8 0 1’.
6- Press ‘Enter’ to save the macro, and don’t let go until the indicator flashes several times.
• Executing a saved macro: Press the button to which the macro is assigned for 1.5 seconds (in the
macro programmed above: ‘Last’).
• Cancelling a macro (example: the macro programmed above):
1- Press ‘TV’ to select the mode in which the macro was programmed.
2 Press and simultaneously. Do not release them until the indicator has flashed several times to
confirm.
3- Press ‘9 9 5’. The indicator flashes several times.
4- Press ‘Last’ to select the button assigned to the macro.
5- Press ‘Enter’. Do not release them until the indicator has flashed several times.
• A macro can contain a maximum of 32 pressed buttons.
• Assign a macro to a button you do not use, because the macro writes over the pre-programmed code.
• A macro can also be used to switch lights on and off (e.g. press a single button to switch off your Home
Theatre and switch on the lights near the TV).
• If a button on the original remote control must be held for several seconds to activate a particular
function, this function cannot be programmed in a macro.
Remarks
Reminders
• This product is a combination of an infrared remote control and a radio-frequency transmitter.
Remote control
: Controls numerous multimedia devices (TV, Stereo, DVD, MediaCenter PC etc.) in the
same manner as the original remote control.
13
UCR-4285 UNIVERSAL REMOTE CONTROL
Transmitter: Controls your COCO receivers. Program your receivers under the same button to control
them simultaneously, or program them under various buttons to control them individually.
• For the ‘transmitter’ function this product must be used in combination with at least one COCO receiver.
The wireless system can be indefinitely expanded with other COCO remote controls and/or receivers.
• The standard setting for the ‘lighting mode’ is COCO house code ‘A’. If the receivers are already set to
a different house code, you can change the house code of the UCR-4285 or change your receivers to
house code A. Follow steps [5-7] to change the house code of the UCR-4285. Use the device button
with the light bulb icon and the desired code from table I below.
• In table II below, you can see which buttons on the UCR-4285 match the number codes of your COCO
receivers. The UCR-4285 can use a maximum of 14 different number codes.
Table I Table II
House
code
receiver
Code
UCR-4285
Number
code
receiver
Button
UCR-4285
A 41000 1 1
B 41001 2 2
C 41002 3 3
D 41003 4 4
E 41004 5 5
F 41005 6 6
G 41006 7 7
H 41007 8 8
I 41008 9 9
J 41009 10 0
K 41010 11 red
L 41011 12 green
M 41012 13 yellow
N 41013 14 blue
O 41014 15 -
P 41015 16 -
UCR-4285 UNIVERSAL REMOTE CONTROL
14
• If your AV device does not have a power button, press the ‘Play’ button in step [13].
• Some TVs cannot be switched on with the ‘Power’ button. In that case, use a channel number button or
consult your TV manual for the correct manner to switch it on.
• If the product does not work or does not work properly:
- Check the correct placement and/or function of the batteries of the transmitter (replace if necessary).
- Check step by step whether everything is programmed properly.
- Some codes are very similar. Try another code in step [7] if some functions on the remote control
work and some do not.
- First press the correct device selection button before you operate the desired device.
- To control lighting: Make sure the house code set on the UCR-4285 is the same as the house code
on the COCO receiver you want to control (see [15] and table I). The number code of the receiver
must match the correct button on the UCR-4285 (see table II).
Dimmer function for lighting
• The dimmer function only works if the lamp is connected to a COCO dimmer receiver!
• If you want to control some of the receivers simultaneously (=program receivers to respond to the same
button on the remote control):
- Do not assign ‘dimmer receivers’ and ‘on/off receivers’ to the same button.
- Do not assign multiple ‘dimmer receivers’ to the same button.
Safety instructions
• Do not expose this product to excessive heat, direct sunlight or moisture.
• Remove the battery from the product if the product will not be used for an extended period.
• Do not attempt to repair this product. If the product is damaged or if you are in doubt about the proper
operation, take the product back to the place of purchase.
• Never use COCO products for life support systems or other applications in which equipment
malfunctions can have life-threatening consequences.
• Do not use the product in damp areas. Clean the device with a dry cloth.
UCR-4285 UNIVERSAL REMOTE CONTROL
Power
• Replace the batteries if the remote control does not function reliably.
• Only use 1.5 Volt AA (LR03) alkaline batteries.
• All the settings will remain intact after changing the batteries.
• Do not throw the batteries into an open fire.
• Respect the local regulations when disposing of batteries.
Wireless
• This product works with infrared signals (control of multimedia devices) and with radio signals (control
of COCO receivers). The latter signals go through walls, windows and doors. The range is maximum 75
metres in the open air. The range indoors is strongly influenced by local conditions such as concrete,
glass and metals. On average, the indoor range is approximately 30 metres.
• New double glass often includes a thin metallic layer. This type of glazing (“HR glass”) allows most
visible light to pass through but has a negative impact on radio signals. If there is HR glass between the
transmitter and receiver, you should expect a significant reduction of the range of the wireless signal.
• This product operates at a frequency of 433.92 MHz. It complies with the essential requirements and
other conditions of R&TTE Directive 1999/5/EC and can be used in all EU countries.
• There may be restrictions on the use of this device outside the EU. If this device is used outside the EU,
check whether the device complies with the local directives.
This product complies with the essential requirements and other relevant provisions of the applicable
European directives. The Declaration of Conformity (DoC) is available at www.coco-technology.com.
If possible, submit this product for recycling after use. Do not dispose of the product with household trash.
15
16
UCR-4285 UNIVERSAL REMOTE CONTROL
Warranty and copyright
This device is covered by a 2-year warranty that begins on the day of purchase. Visit www.cocotechnology.com/warranty for additional information. Reprinting of (portions of) this manual without
permission from Pan-Trade International B.V. is expressly prohibited.
UCR-4285 UNIVERSAL REMOTE CONTROL
PAN-TRADE INTERNATIONAL B.V.
P.O. BOX 126
4760 AC ZEVENBERGEN
THE NETHERLANDS
www.coco-technology.com
17
Declaration of Conformity
Pan-Trade International BV declares that the COCO product, model:
type designation UCR-4285 UNIVERSAL REMOTE CONTROL
item number 74030
is in compliance with the essential requirements and other relevant provisions of directives R&TTE
1999/5/EC, EMC 2004/108/EC and LVD 2006/95/EC and is compatible with the standards EN 300 2201/3, EN 55015 and EN 301 489-1/3.
Manufacturer / Authorised representative,
M.A. Hoekstra, managing director
Zevenbergen, 2008-01-30
Loading...