COBY electronic TFDVD1595S3, TFDVD2295S2, TFDVD2495, TFDVD1995S2 User Manual
Precautions
For recycling or disposal information about this product, please
contact your local authorities or the Electronics Industries
Alliance:www.eiae.org.
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufcient magnitude to constitute
a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operation and servicing instructions in the
literature accompanying the appliance.
For Cust omer Use:
Enter below the s e rial number that is located on the
rear of the unit. Retain this information for f uture reference.
Model No.
Seria l No.
TFDVD2495/2295S2/1995S2/1595S3
Precautions
WARNING: To prevent re or shock hazard, do not expose this device to rain or moisture. Dangerous high
voltage is present inside the enclosure. Do not open the cabinet.
Note: If the product suddenly has no response or powers off, an electrostatic discharge may be the cause.
In this circumstance, please follow the procedures below for recovery:
• Unplug the unit. Wait 30 seconds.
• After 30 seconds, plug the unit in and turn it on again.
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and•
This device must accept any interference received, including interference that may cause undesired •
operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•
Consult the dealer or an experienced radio/TV technician for help•
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC rules. Do
not make any changes or modications to the equipment unless otherwise specied in the manual. If such
changes or modications should be made, you could be required to stop operation of the equipment.
Important Safety Instructions
Warnings and precautions
To prevent any injuries, the following safety precautions should be observed in the installation, use, servicing
and maintenance of this equipment. Before operating this equipment, please read this manual completely,
and keep it nearby for future reference.
Important Safety Instructions
Read Instructions: All the safety and operating instructions should be read before the product is operated.1.
Retain Instructions: The safety and operating instructions should be retained for future reference.2.
Heed Warnings: All warnings on the product and in the operating instructions should be adhered to.3.
Follow Instructions: All operating and usage instructions should be followed.4.
Do not place the equipment on uneven or unstable carts, stands, tables, shelves etc. The equipment 5.
may fall, causing serious injury to children or adults and serious damage to the equipment itself. Always
place the equipment on the oor or on a surface that is sturdy, level, stable and strong enough to support
the weight of the equipment.
Use only a cart or stand recommended by the manufacturer. This equipment and recommended cart or 6.
stand should be handled with care. Quick stops, excessive force, and uneven surfaces may cause the
equipment and cart/stand to overturn.
Do not disable the 3-wire grounding type plug. The grounding pin on the 3-prong plug is an important 7.
feature. Removing the grounding pin will increase the risk of damaging the equipment.
If you can not t the plug into the electrical outlet, contact an electrician to install a grounding outlet.8.
Always operate this equipment from the type of power source indicated on the rear of the serial/model 9.
plate.
Never overload wall outlets and extensions.10.
Use and handle the power cord with care. Do not place any heavy objects on the AC power cord.11.
Do not pull the AC power cord. Do not handle the AC power cord with a wet hand.12.
Do not touch the power cord and antenna cable during lightning.13.
Remove the plug from the wall outlet, if the equipment will not be used for a long period of time.14.
Do not place, use or handle this equipment near water.15.
Never expose the equipment to liquid, rain, or moisture. Seek service if any of the above is spilled into 16.
the equipment.
Do not expose the equipment to extreme temperature or to direct sunlight, as the equipment may heat 17.
up and suffer damage.
Do not install the equipment near any heat sources such as radiators, heat registers, stoves, or any other 18.
apparatus that might produce heat.
Do not attempt to service the equipment yourself.19.
Opening and removing the covers may expose you to dangerous voltage or other hazards and may void 20.
your warranty. Refer service to qualied personnel.
Do not place or drop any other objects on top.21.
Do not insert anything into the ventilation holes of your equipment. Inserting any metal or flammable 22.
objects may result to re or electric shock.
Protect the power cord from being walked on or pinched particularly at plugs ,convenience receptacles, 23.
and the point where they exit
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been 24.
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Always remove the power cord from the outlet before cleaning the equipment.25.
Never use liquid or aerosol cleaners on the equipment. Clean only with a soft dry cloth.26.
Only use attachments/accessories specied by the manufacturer.27.
Where the mains plug or an appliance coupler is used as the disconnected device, the disconnect device 28.
shall remain readily operable.
Important Safety Instructions
Antenna Safety Instructions
If an outdoor antenna is connected, follow the precautions below:
An outdoor antenna should not be located in any area where it could come in contact with overhead •
power lines, or any other electric light or power circuits.
When installing an outdoor antenna system, extreme caution should be taken to prevent contact with •
power lines. Direct contact with power lines may be fatal and should be avoided at all costs.
Section 810 of National Electrical Code (NEC) provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the
grounding electrode.
Listening with Earphones
Listen at moderate Volumes to avoid hearing damage.•
If you hear no sound during playback, do not turn the Volume up as the music may suddenly begin at a •
high Volume. Excessive sound pressure from earphones and headphones can cause hearing loss.
To avoid damaging your ears, adjust the Volume to the lowest level before playback, and turn up to the •
desired level when playback has started.
Legal and Trademark Notices
Coby is a registered trademark of Coby Electronics Corporation. All other trademarks and logos are property
of their respective owners unless indicated otherwise.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of
Dolby Laboratories. Condential unpublished works. © 1992 -1997 Dolby Laboratories, Inc. All rights
reserved.
This TV incorporates High-Denition Multimedia Interface (HDMITM) technology. HDMI, the HDMI logo and
High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Note: This product contains electrical or electronic materials.The presence of these materials may, if not
disposed of properly, have potential adverse effects on the environment and human health. Presence of this
label on the product means it should not be disposed of as unsorted waste and must be collected separately.
As a consumer, you are responsible for ensuring that this product is disposed of properly.
Table of Contents
Table Of Contents
Precautions
Important Safety Instructions
Main Feature-----------------------------------------------------------------------------------------------------------------------------1
Package Contents-----------------------------------------------------------------------------------------------------------------2
Unit View---------------------------------------------------------------------------------------------------------------------3
Remote Control ------------------------------------------------------------------------------------------------------------------4
Cable Connections----------------------------------------------------------------------------------------------------------------7
TV Function----------------------------------------------------------------------------------------------------------------11
AV Function-----------------------------------------------------------------------------------------------------------------------------15
PC Function----------------------------------------------------------------------------------------------------------------------------16
DVD Operation-------------------------------------------------------------------------------------------------------------------------17
USB/Card Access--------------------------------------------------------------------------------------------------------------18
DVD Playback Function-----------------------------------------------------------------------------------------------------------19
DVD Setup----------------------------------------------------------------------------------------------------------------------------21
Troubleshooting -----------------------------------------------------------------------------------------------------------------------23
Specifications ----------------------------------------------------------------------------------------------------------------------24
Main Features
This product incorporates the LCD display and the TV receiver in one system.
Multiple Mode
TV
AV
S-VIDEO
COMPONENT
DVD
VGA
HDMI
High Quality Property
High Resolution
Adopt an MPEG2 decoding format to achieve horizontal resolution more than 500 lines.
Superior sound
Built-in Dolby Digital decoder to output high quality sound effects.
Screen
Support the picture size of a normal screen (4:3) and a wide screen (16:9)
LCD (Liquid Crystal Display)
Designed with color TFT liquid crystal display clearly shows the data.
LCD Information
The LCD panel used in this television contains millions of thin lm transistors that have been manufactured
using a high-technology process to deliver a crisp, clear, and detailed picture. Occasionally, a few of these
transistors may become stuck or non-active; please note that this does not affect the performance of the
television.
NOTE: It is normal for a TFT screen to experience some light or dark spots appearing on the LCD screen.
Advanced Playing Features
Compatibility
DVD, CD, MP3, CD-R,CD-RW, JPEG discs compatible.
All Playback Functions
Fast forward and reverse, repeat playback, program playback.
Power Supply:
Connect one end of the supplied power cord to the power jack on the unit rear
panel and the other end
a long time, disconnect the plug from the outlet.
Power Management:
Before plugging the power cord into the AC outlet, make sure that all necessary •
connections have been properly made.
If the unit will not be used for a long period of time, disconnect the power and •
remove the batteries from the remote.
to the AC100-240V wall outlet. If the unit will not be used for
1
Package Contents
Please make sure the following items are included with your LCD TV/monitor. If any item is missing, contact
your dealer.
a.
b. c.
a, Main Unit
b, Power Cord & RCA Cable
c, Remote Control Unit
2
3
9
10
11
Wall Mounting - Attach the TV case to the wall
Separate the TV case and the stand-base by removing screws before installation.•
Use the VESA standard mountings to x the unit on the wall. Take care when mounting, it may cause •
damage or serious injury should it fall from its mountings. See the Specification page for VESA
informaiton. A variety of mounts are available in your local retailer, see instructions when installing the
unit.
NOTE: 10 mm is the maximum depth that screws could be driven inside the unit cabinet without damaging
the player.
1. TFT SCREEN
Present high resolution pictures
2. POWER INDICATOR
The indicator lights bright blue when the
TV is on, it will dim when the TV is turned
off (standby mode).
3. REMOTE SENSOR
Sense the remote control signal.
4. VOL+/-
Adjust sound output level.
5. CH+/ Press to skip channels.
6. MENU
Display the system setup menu.
7. SOURCE
Press this button to switch modes.
8. POWER
Press to turn on/off the player.
9. Disc Slot
10. Card Slot
11. USB Port
12. STOP - Stop disc playback.
13. PLAY/PAUSE - Start/hold disc playback.
14. OPEN/CLOSE - Open/close the disc room.
15. Wall Mounting Thread X 4
16. Connector Panel
17. Unit Stand
18. Screw - This screw is connecting the TV case
to the unit stand-base.
Unit View
NOT E : See "Ca b le Conne c tions" se c tion fo r
detailed description on connectors.
2
1
3
4
5
6
7
8
9
10
11
12
13
14
Remote Control
12
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
19
20
32
21
22
23
24
25
26
27
28
29
30
31
33
34
35
36
37
38
Remote Control Drawing
1. POWER
Turn the unit on or off (standby).
2. Numeric Keypad
Input numberic data. Access the TV channel directly.
3. Sub-channel Selector <->
This button is usually used with the numeric keypad
to tune to a channel substation (e.g., 4-1, 4-2).
e.g. To tune to channel 13-2, press these keys in
sequence: <1>, <3>, <–>, <2>.
4. Skip Backward
Repeatedly press this button to skip backward through DVD
playback.
5. A-B
Repeat specifed playback A to B in the DVD mode.
6. Fast Reverse
Search fast backward through DVD playback.
7. Stop
Stop disc playback.
8. VOL+/-
Adjust the volume level up and down.
9. INFO
Display system current working information.
10. CH/LIST
Display the TV program list, use the up/down direction
button
to select the desired program in the list, press OK to
access.
11. TV/DVD
Switch between the TV mode and the DVD mode.
12. Direction & OK
This set of buttons is usually used when working with system setup menu, use arrow buttons to
select an option in the menu, press OK to conrm settings.
13. SLEEP
Cycle through the sleep timer options.
14. SUBTITLE
Display available DVD subtitles.
15. DISC MENU
Access the DVD root menu.
16. GUIDE
Display TV electronic program guide.
17. MTS
Set the audio mode.
18. TITLE
Access the DVD title menu.
19. LIGHT
Turn the front panel light on/off.
4
Remote Control
20. ANGEL
Some discs are recorded with Multi-angle, press this button to chose the desired viewing angle.
21. OPEN/CLOSE
In the DVD mode, press this button to take in/out disc automatically.
22. RETURN
Reveal the previously viewed channel.
23. Skip Forward
Repeatedly press this button to skip forward through DVD playback.
24. SLOW
Press this button to have current playback advanced in a slow motion, repeatedly press this
button to change advance speed. You can press Play/Pause to pause current playback, and
then repeatedly press this button to have playback moved step by step forward. To resume
normal playback, press Play/Pause.
25. Fast Forward
Search fast forward through DVD playback.
26. Play/Pause
Press this button to start/hold DVD playback.
27. SOURCE
Display the working mode menu, use the up/down direction button to select a desired working
mode, press OK to enter.
28. CH+/ Tune to a higher or lower channel.
29. MUTE
Disable/enable audio output.
30. CH FAV
Display the TV favorite channels list.
31. MENU
Access the TV’s main menu to adjust system options.
32. DVD SETUP
Display the DVD system menu.
33. EXIT
Exit the TV system menu.
34. PROGRAM
Display the DVD program menu.
35. CC
Repeatedly press this button to select a desired TV closed caption mode.
36. GOTO
Go to a desired section on a disc via information input.
37. REPEAT
Repeat DVD title/chaptor or CD tracks.
38. ZOOM
Repeatedly press this button to zoom in/out DVD images.
5
Loading...