Order Form...............................................................................44
IfYou Think You Need Service......................Back Cover
Features of This Product
• UHF FM Frequencies
• No License Required
• No Air Time Fees
• Up to 2 mile range
• 14 Main Channels
• 38 CTCSS Subchannels
• LCD Function Display
• Talk Confirmation To n e
• Ca l l / R ing Bu t to n
• Recharging Pads
• Retractable Antenna
• Auto Battery Saver Circuity
• Auto Squelch
• 10 Memory Locations
• Full Channel/CTCSS Scan
• Lock Key
• Ring/Vibrate Notification
• Belt Clip
• Water Resistant
1
Operation
Operation
Battery
Installation
Note
Batteries not included with
microTALK2-way radio.
Install Batteries
Clear antenna.
Pull lock tab down
and lift door up
(towards you) to
remove battery
cover.
Insert four “AAA”
batteries. Position
batteries according
to po l a ri ty marki n g s.
Note
Always use high quality
alkaline or NiMH batteries.
Incorrect positioning can
damage both the batteries
and the unit.
Only the Cobra NiMH
battery (Part # FA-BP)
pack can be recharged.
See Accessories on page ??.
Charge ports for recharging
NiMH (Nickel Metal Hydride)
battery pack are located on
back of unit.
Note
When batteries are low or
need charging the
BATT LOW indicator will
blink.Replace alkaline
batteries or recharge NiMH
battery pack.
2
3
Operation
Operation
Turning
On Your
microTALK
Note
Whenever the unit is on you
can receive communications.
Illuminating
the Display
Turning On Your microTalk
Press and holdthe power button for 2
seconds.An audible “tone”will indicate the unit is
on and then the LCD will go through a 3 second
self-test and then go to Operational Mode.
Illuminating the Display
Press and releaseLIGHT/MAX RANGE
button to illuminate display for ten seconds.
Auto Battery Power Saver
Your microTALK has a unique circuit designed to
extend battery life. If there are no transmissions
within 10 seconds, the unit will automatically
switch to battery SaveMode.
Theicon will flash.
Select Main Channel (1-14)
Turn on the microTALK.An audible “tone”will
indicate the unit is on and then the LCD will
go through a 3 second self-test and then go to
Operational Mode.
Select channel by moving the Channel Button
up or down.
Auto Battery
Power Saver
Note
The Auto Battery Save Circuit
does not effect the unit’s
ability to receive incoming
transmissions.
Select Main
Channel
Note
Units must be on same
channel and subchannels to
communicate.
Note
Channels 8-12 generally are
less used and give better
results for communications
in most areas.
Note
Push and hold the channel
up/down button for fast
channel advance.
4
5
Operation
Operation
Select CTCSS
Subchannel
Note
If you push and hold the
Mode Button,the LCD display
will cycle through
the different functions.
Note
To return to Operational
Mode and not save your last
setting push and release talk
button.
Note
CTCSS (Coded Tone
Controlled Squelch System) is
an advanced subcoding
system that allows
segmentation of a main
channel.
Select CTCSS Subchannel (00-38)
The CTCSS Subchannel allows the user to utilize a less
used channel range (00-38) within a main channel.
Turn on the microTALK.An audible “tone” will
indicate the unit is on and then the LCD will go
through a 3 second self-test and then go to
Operational Mode.
Select main channel by the Channel Button up
or down.
Se l e cts u bcode number by moving the Ch a n n e l
Bu t ton up or dow n.
When desired code is displayed press andreleaseLock Button. If key stroke tone is
on,an audible tone will confirm your selection.
Select CTCSS
Subchannel
Note
Press and hold the Channel
Button up and down for fast
channel advance.
Push and releaseMode Button. Small num-
bers flash next to channel display on LCD.
6
7
Operation
Operation
Battery LowCalling
Note
When battery capacity is at
the 1/4 level it is recommended that you replace
alkaline batteries or recharge
your NiMH (Nickel Metal
Hydride) battery pack.
Only the Cobra NiMH
battery (Part # FA-BP)
pack can be recharged.
Note
NiMH rechargeable battery
Pack (item #FA-BP) and desktop charger (item #FA-CR)
are not included with this
unit. See Accessories section
on page 43.
Battery Low
When in normal use the icon may begin
flashing. This is a warning to you that your
batteries are getting low.
Replace alkaline batteries as soon as possible
and/or recharge NiMH battery pack.
Calling Another Party
To alert another party that you wish
to communicate:
Turn onyour microTALK 2-way radio.
An audible “tone”will indicate the unit is on.
The LCD will go through a 3 second self test
and then to Operational Mode.
Placeantenna in full upright position.
Another
Party
8
9
Operation
HeadlineOperation
Talking to
Another Party
Note
Your incoming “Call”audio
ringing level is dependent on
your unit’s volume s e t t i n g.
Select desired channel by moving the Channel
Button up and down. Both the calling and
receiving units must be on same channel and
subchannel for the call function to work.
Press and releaseCall Button. The indica-
tor icon will flash and the icon will remain
on for 3 seconds. The unit you are calling will
hear a 2 second ring tone.
Your microTALK is always in the Standby Mode
when theTalk Button is not depressed.
Press and holdTalk Button.
Th ei con will appe a r.
Hold mic about 2 inches from mouth.
Speak in a normal voice.
Talking to
Another Party
Note
While Talk Button is
depressed you cannot
receive incoming calls.
Note
When you release the
Talk Button,the person you
are talking to will hear a tone
indicating that it’s ok to talk.
See Talk Confirmation Tone
section on page 14.
10
ReleaseTalk Button and listen for response.
11
Operation
Operation
Talk
Confirmation
Tone
Standby Mode
Note
While Talk Button is
depressed you cannot receive
incoming communications.
Talk Confirmation Tone
Your listener will hear an audible
tone when you release
theTalk Button.
This alerts the other party t h at
you are finished talking and it’s
OK for them to begin talki n g.
Standby Mode
When finished talking:
ReleaseTalk Button to receive incoming
transmissions.
Your microTALK is always in the Standby Mode
when the Talk Button is not pressed and you are
not in Function Mode. See Advanced Features
section on page 14.
Auto Squelch
Your microTALK is equipped with Auto Squelch,
which automatically shuts off weak transmissions
and unwanted noise due to terrain conditions or
if you have reached your range limit.
Maximum Range Extender
Au to squelch can be te m po ra rily re m oved to allow
all signals to enter (Maximum Range Exte n d e r ) .
Push and holdLIGHT/MAX RANGE
Button to allow all signals to enter.
Auto Monitor
When the signal you want to hear is consistently
weak, you may place the radio in Maximum
Range Mode without having to constantly hold
the button: Press and hold the Maximum Range
Extender button for five seconds.You will hear an
audible “beep”confirmation. To return to normal
operation,momentarily press the Maximum
Range Extender Button again or change channels.
Auto Squelch
Maximum
Range
Extender
Note
To learn more about the
range of your microTALK,
see page 35.
Range is dependent on
battery condition and
geographic territory.
Auto Monitor
12
13
Advanced Features
Advanced Features
Advanced
Features
No te
When using or prog ra m m i n g
f u n ct i o n s,pushing and
releasing the Mode Bu t t on or
the Lock Bu t t on will save all
e n te red info r m a t i o n .
No te
To exit out of Fu n c tion Mod e
and return to Ope ra t i o n a l
M ode without saving ente re d
i n f ormation simply press the
Press to Talk Bu t to n .
Advanced Features
Your microTALK has many advanced features
not found on other 2-way radios.
These include:
• 10 Memory Storage Location and Recall
• Full Channel/Sub Channel Scan
• Dual Watch
• Ring/Vibrate Notification Modes
• Tone Indicator Settings
Key Stroke Tone
Talk Confirmation Tone
• Lock Key
Programming Memory Locations
Your microTALK has 10 memory (0-9) locations
for storing your most frequently used channels.
Turn on the microTALK. An audible “tone”will
indicate the unit is on and then the LCD will
go through a 3 second self-test and then go to
Operational Mode.
Push and releaseMode Button until
icon and a memory location flashes.
Programming
Memory
Locations
14
Select memory location you wish to change by
pressing the Channel Button up and down
continued
15
Advanced Features
Advanced Features
Programming
Memory
Locations
Note
Once you enter Memory
Mode you can talk and listen
to any channel you select
after programming is
complete. See Using Memory
Locations section on
page 19.
Programming Memory Locations continued
Press and releaseMode Button again.
Main Channel andicon will flash.
Select desired main channel you wish to store
(1-14) by pushing the Channel Button up
or down.
Push the Channel Button up or down to set
the main channel in memory and move to
subchannel selection. The subchannel begins
flashing.The icon will remain flashing.
Select desired subchannel you wish to store
(00-38) by pushing the Channel Button up
or down.
Note
Push and hold the Channel
Button up and down or fast
channel advance.
Note
You can push and hold the
Talk Button to begin talking
anytime.
16
continued
17
Advanced Features
Advanced Features
Programming
Memory
Locations
Note
If you push and hold the
Mode Button,the LCD display
will cycle through the
different functions.
Programming Memory Locations
After selecting your Memory Channel and
Main/Sub Channels, for immediate entry
pressTalk Button.
or...
After selecting you Memory Channel and
Main/Sub Channel,DO NOT press any buttons
for 10 seconds and your unit will automatically
set the Memory and Main/Sub Channels. It will
then go to the NEW channel.
Press and releaseLock Button to return to
Operational Mode original Main Channel.
or...
Press and releaseMode Button to proceed
to next Function Mode (Scan).
Memory Channel Recall/Talk
To recall a channel in memory:
Press and releaseMode Button until
icon and a memory location flashes.
Select desired memory location you wish
to recall (0-9) by pressing the Channel
Button up or down.
Using Memory
Locations
18
continued
19
Advanced Features
Advanced Features
Using Memory
Locations
Note
If the Mode Button is pushed
while listening/talking,
programming will begin.
See Programming Memory
Locations on page 15.
Press and holdTalk Button and talk. Your
radio will stay on this recalled location until
you exit out of Memory Function Mode.
Repeat step 2 for recalling other memory
locations.
To exit the Memory Mode and return to
Operational Mode:
Press and releaseMode Button.
Scan Function
Turn on microTALK.An audible “tone”will
indicate the unit is on and then the LCD will go
through a 3 second self-test and then go to
Operational Mode.
Press and releaseMode Button until
icon and main channel flashes.
Scan Function
Note
The microTALK“zeros out”the
subchannels to allow scanning of the main channels.
20
continued
21
Advanced Features
Advanced Features
Scan Function
Scan Function continued
Press Channel Button up or down and the
unit will begin scanning the main channels.
Unit will co ntinue to scan all main channels and
s to p,if an incoming transmission is dete cte d .
Your microTALK will pick it up for 10 seconds.
Within 10 seconds you can:
Press and hold Talk Bu t ton and talk. Your ra d i o
will re t u rn to Ope rational Mode on that channel.
or...
Press and releaseChannel Button up or down
to rescan the main channel.
or...
Proceed to subchannel scan on next page.
To scan subchannels:
Press and releaseMode Button and
subchannel and Scan Icon will flash.
Press and release Channel Button up or down
and subchannel scanning begins and stops
when an incoming transmission is detected.
22
continued
23
Advanced Features
Advanced Features
Scan Function
Note
If you wish to proceed to the
next Function Mode,press
and release Mode Button.
Scan Function continued
Your microTALK will pick it up for 10 seconds.
Within 10 seconds you can:
Press and holdTalk button and talk.Your ra d i o
will re t u rn to Ope rational Mode on that channel.
or...
Press and release Channel Button up or down
to rescan the main channel.
To exit the Scan Mode and return to
Operational Mode:
1 Press and releaseMode Button.
Ringer/Vibrate Modes
Your microTALK will signal you that there is an
incoming transmission with either a tone or a
vibration or both. To set for Ringer/Vibrate:
Turn on microTALK.An audible “tone”will
indicate the unit is on and then the LCD will go
through a 3 second self-test and then go to
Operational Mode.
Press and releaseMode Button until
icon flashes.
Ringer/Vibrate
Modes
24
Press Channel Button up and down until
icon appears for Ringer Only Mode.
continued
25
Advanced Features
Advanced Features
Ringer/Vibrate
Modes
Note
When you press and hold the
Talk Button,the unit exits out
to Operational Mode.
If,after 10 seconds no selection is made,the unit will
return to Operational Mode.
Ringer/Vibrate Modes continued
Press and release Channel Button up and down
again.icon appears for Vibrator Only Mode.
Press and release Channel Button up and
d own again and bo t hi c ons will be displaye d
for Ringer and Vi b rate Mod e .
After selecting the mode you desire press andreleaseLock Button orMode Button
to proceed to next function.
Ringer/VibrateTest
To test the ringer/vibrate Mode:
Turn on unit.
Press and holdLock Button andCall
Button simultaneously.
Unit will ring, vibrate,or ring/vibrate for 4
seconds.
Note
Unit must be in Operational
Mode to test ring/vibrate.
26
27
Advanced Features
Advanced Features
Tone
Settings
Tone Setting
PressMode Button until flashing
Press Channel Button up or down to turn
on or off.
To set option:
PressLock Button.This will immediately
enter new setting;
PressMode Button.This will enter new setting and go to new Function Mode;
Wait 10 seconds. It will go to Operational
Mode with new setting.
Talk Confirmation Tone Indicator
To te m po ra r ily eliminate the Talk Co n f i rm ation To n e :
PressMode Button until flashing
Press Channel Button up or down to turn
on or off.
To set option:
PressLock Button.This will immediately
enter new setting;
PressMode Button.This will enter new setting and go to new Function Mode;
Wait 10 seconds. It will go to Operational
Mode with new setting.
2928
Advanced Features
Advanced Features
Lock Function
Note
Call Button,Range Extender
Button and Talk Button
do not lock and are fully
operational while the unit
is locked.
The unit cannot lock while in
Function Mode.
Lock Function
The purpose of the LOCK function is to lock most
buttons to avoid accidental operation.
To engage the LOCK function:
Press and hold for one seco n dLock Bu t to n .
i con flashes. If the Beep Fu n ction is ON yo u
will hear an audible co n f i rm at i o n .Most butto n s
a re loc ke d .
To“unlock”press and releasebutton again.
If the Beep Fu n ction is ON you will hear an audible co n f i rm at i o n . Most buttons are loc ke d .
Buttons are“unlocked” andicon disappears.
Dual Watch Function
Dual Watch allows you to simultaneously monito r
a ny two pre s e l e cted Family Radio Se rv i ce channels.
Select first channel and CTCSS code which
you desire to Dual Watch. (please see
pages 6 and 7).
Dual Watch
Function
30
continued
31
Advanced Features
Advanced Features
Dual Watch
Function
Dual Watch Function
Press and releaseMode Bu t ton unt i l
i con flashes.
Pre s s Channel Bu t ton up and down to
s e l e ct second channel.
Dual Watch
Function
PressMode Bu t ton to set CTC S S .
C TCSS channel numbers will flash.
Pre s s Channel Bu t t on up and down
to select CTC S S .
PressLock Button.This will store the second channel and CTCSS and start Dual Watch.
To terminate Dual Watch and go to Normal
Mode, press Lock or Talk Buttons.
32
continued
33
Dual Watch Function
microTALK Range
Dual Watch
Function
Dual Watch Function
To enter Dual Watch when the second channel
and CTCSS are already stored, press the
Mode Button untilicon flashes.
Pre s sLock Bu t to n . Dual watch will be g i n .
Pre s s Talk Bu t ton to exit Dual Watch Mod e.
microTALK Range
Your micro TA L K Radio has a range of up to2 miles.
This effective range can be shortened under
some conditions.
Under flat,o pen co n d itions you will ex pe rie n ce the micro TA L K ’s
maximum ra n g e.
Range can be re d u ce d
by buildings and fo l i a g e
in the path of the signal.
Range will be furt h e r
re d u ced by dense
foliage and hilly te rra i n .
To achieve maximum
range the auto squelch
can be ove r ri d d e n .
Re fer to Ma x i m u m
Range Extender sect i o n
on page 13.
microTALK
Range
34
35
Making Life Easier and Safer
Making Life Easier and Safer
microTALK
2-Way Radio
Can Make
Life Easier
and Safer
microTALK 2-Way Radio Can Make Life
Easier and Safer
As you become familiar with your microTALK
Radio you will find many of your own uses for
the unit. Some suggestions include:
Talking with
fellow hikers.
Keeping track of the
kids in a shopping mall.
microTALK 2-Way Radio Can Make Life
Easier and Safer
Checking on traveling
companions in another
car.
Holster/Belt Clip/Desk Stand
Your microTALK Radio comes with a custom mold ed plastic holster.Its unique dual-function design
enables it to act as a handy desktop storage unit,
as well as easily attaching to your belt for maximum convenience and portability.
Agree on a meeting
spot after an event.
microTALK
2-Way Radio
Can Make
Life Easier
and Safer
Holster-
Belt Clip and
Desk Stand
Co m m u n i cating be twe e n
b a s e m e nt and first,s e cond or third floo r.
36
Ta l king to a neighbor or
a fri e n d .
Desk StandBelt Clip
37
E x t e rnal Microphone/Speaker Jack
Caring for Your MicroTalkRadio
External
Microphone/
Speaker Jack
Note
External microphone/
speaker (item #FA-SM) is not
included with this unit. See
Accessories section on page
?? for available units.
External Microphone/Speaker Jack
Your microTALK 2-Way Radio can be fitted with
an external microphone/speaker, (not included)
freeing your hands for other tasks.
To attach the external microphone/speaker:
Open Mic/Spkr tab on top of unit.
Caring for Your microTALK Radio
The microTALK 2-Way Radio will give you years
of service if cared for properly.
Here are some suggestions:
Handle unit gently.Keep away
f rom dust.
Caring for Yo u r
m i c ro TA L K
R a d i o
Note
Modifying or tampering
with the radio’s internal
components can cause
malfunction and will
invalidate the warranty.
If your radio is not performing as it should,please call
Cobra at 773.889.3087.Do
not return the unit to the
retailer.
Insert jack into the Mic/Spkr ports.
Never place the
unit in water or in
a moist place.
Avoid ex po s u re
to ext reme
te m pe rat u re s.
3938
Frequency Range
MicroTalkSpecifications
Frequency
Ranges
The microTalk unit represents one of the most
advanced FM two-way radios available.
8. TRANSIENT FREQ.BEHAVIOR
a)TXONmS 30
b) TX OFF mS 5
D.POWER SUPPLY
1.BATTERY LIFE (1:1:8 RATIO) HR 24
2.BATTERYV4.8 - 6.0
4140
Limited Two Year Warranty
COBRA ELECTRONICS CORPORATION warrants that its
COBRA FRS Radios, and the component parts thereof, will
be free of defects in workmanship and materials for period
of two (2) years from the date of first consumer purchase.
This warranty may be enforced by the first consumer
purchaser,provided that the product is utilized within
the U.S.A.
COBRA will,without charge,repair or replace, at its option,
defective FRS radios, products or component parts upon
delivery to the COBRA factory Service Department, accompanied by proof of the date of first consumer purchase ,
such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship
the product for warranty service, but the return charges
Cobra Electronics
Corporation
6500 West Cortland Street
Chicago,Illinois 60707
will be at Cobra's expense, if the product is repaired or
replaced under warranty.
Exclusions:This limited warranty does not apply; 1) to any
product damaged by accident;2) in the event of misuse or
abuse of the product or as a result of unauthorized alterations or repairs;3) if the serial number has been altered,
defaced or removed;4) if the owner of the product resides
outside the U.S.A.
All implied warranties,including warranties of
merchantability and fitness for a particular purpose
are limited in duration to the length of this warranty.
COBRA shall not be liable for any incidental, consequential or other damages;including,without limitation,
damages resulting from loss of use or cost of installat i o n .
Some states do not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion
or limitation of incidental or consequential damages, so
the above limitations may not apply to you.
(1) NiMH Rechargeable
Battery Pack
High performance Nickel Metal
Hydride battery pack for
multiple recharging
FA-BP $29.95
Ear Bud Mic with PTT
I n te g ra ted spe a ker/mic adapte r
that fits in your ear.Includes
s h i r t clip.M A-EBM $29.95
Optional Accessories
2 Po rt De s k t op Ch a rg e r
Ch a rges your micro Talk Radio
and (1) NiMH batte r y pack
FA- C R$ 2 4 . 9 5
You Can Find These Fine Accessories AtYour Local
Cobra Dealer
If you wish, you can order directly from Cobra.
Order by phone
Call 1.773.889.3087
(Press 1 from the main menu) 8 a.m.-6 p.m. M-F CST. )
Order by mail or fax
Please fill out order form on ne xt page, and mail/fax directly
to Cobra.
Order over the Web
www.cobratelectronics.com.
Vox Headset Mic
VOX (Voice Operated
Transmitter) headset and
microphone allows hands-free
operation.
MA-VOX$49.95
Replacement Belt Clip
FA-HR3 $4.95
42
43
Accessory Order Form
Item #DescriptionCost Ea. Qty. Amount
FA-BPNiMH Re c h a rgeable Bat te ry Pa c k$29.95
M A - E B MEar Bud Mic with PTT$ 2 9 . 9 5
M A - VOXVox Mi c$ 4 9 . 9 5
FA-CR2 Port Desktop Charger$24.95
CA-40Lapel Microphone $25.95
FA-HR3Holster Belt Clip$4.95
For credit card orders fill out order
form and fax to: 1.773.622.2269
or call 1.773.889.3087
(Press 1 from the main menu)
8:00 am - 6:00 pm,M-F,CST.
Please print clearly
Name
Address (No P.O.Box)
CityState
Zip
Telephone ( )
Credit Card No.Exp. Date
Customer Signature
Circle One: Visa MasterCard Discover
Subtotal
(Tax if applicable)
Shipping/handling*
Total
*See chart.
Ma ke check or money order (no stamps)
payable to:
Cobra Electronics
Attn:Accessories Dept.
6500 West Co rtland St.Ch i ca g o ,IL 60707
Allow 7 to 10 days??? for delivery.Offer valid in Continental U.S.only.
44
Cobra Electronics Corporation
6500 West Cortland Street
Chicago, IL 60707
IfYou Think You Need Service
For te c h n i cal assistance,please call our Au to m a ted Help Desk which can assist
you by answe ring the most fre q u e n t l y asked questions about Co b ra prod u ct s.
(773) 889-3087
24 hours a day, 7 days a week.
A Consumer Service Representative can be reached through this same number
8:00 am - 6:00 pm,Monday through Friday,CST.
Technical assistance is also available on-line in the Frequently Asked Questions (FAQ)
section at www.cobraelectronics.com or by e-mail to
productinfo@cobraelectronics.com
If you think you need service call 1.773.889.3087
“If your product should require factory service please call Cobra first before sending your unit in.
This will ensure the fastest turn-around time on your repair.”
You may be asked to send your unit to the Cobra factory.It will be necessary to furnish the following in order to have the product serviced and returned.
1. For Warranty Repair include some form of proof-of-purchase, such as a mechanical reproduction
or carbon or a sales receipt. If you send the original receipt it cannot be returned.
2. Send the entire pr oduct.
3. Enclose a description of what is happening with the unit.Include a typed or clearly print name
and address of where the unit is to be returned.
4. Pack unit securely to prevent damage in transit. If possible, use the original packing material.
5. Ship prepaid and insured by w ay of a traceable carrier such as United Par cel Service (UPS) or First
Class Mail: to avoid loss in transit to: Cobra Factory Service, Cobra Electronics Corporation,6500
W.Cortland St., Chicago,IL 60707.
6. If the unit is in war ranty, upon receipt of your unit it will either be repaired or exchanged
depending on the model. Please allow approximately 3 to 4 weeks before contacting us for
status. If the unit is out of warranty a letter will automatically be sent informing you of the
repair charge or replacement charge. If you have any questions, please call 1.773.889.3087 for
assistance.
O pe rating Instru ctions
for your Co b ra micro TA L K
2Way Radio
FRS 305
“Ingenious Prod u cts for Easier Co m m u n i cat i o n .”
The Family Radio Service Story
The Family Radio Service Story
Ever wish you could talk to someone who wasn’t
within earshot? Like contacting ski partners back
at the lodge? Or letting a friend know how to find
you in a busy mall? Cobra’s microTalk FRS 305 is a
great way for friends or family to increase their
fun–and safe ty – by staying in touch while on the go.
The FCC (Federal Communications Commission)
has created 14 license free frequency bands,
or channels, called Family Radio Service (FRS)
frequencies. All of these 14 channels are easily
accessed on your Cobra FRS radio. These channels are in the UHF (Ultra High Frequency) band
which means great penetration through buildings, thick forests, hills, and other dense structures.
They are also FM (Frequency Modulation) signals
which means crystal clear reception even in
crowded noisy environments.
FCCWarnings
Replacement or substitution of transistors, regular
1
diodes or other parts of a unique nature, with
parts other than those recommended by Cobra,
may cause a violation of the technical regulations
of part 95 of the FCC Rules, or violation of Type
Acceptance requirements of Part 2 of the Rules.
Included with your microTalk
1. Holster/Belt Clip/Desk Stand
A1
Controls and Indicators
1. An te n n a
2 . Mi c ro p h o n e / Spe a ker Ja c k
3 . On / Off Power Bu t to n
4 . LCD Di s p l ay Pa n e l
5 . Light/Max Range Bu t to n
6 . Down/Up Volume Co n t ro l
7 . Spe a ke r
8 . Ba t te ry Co m p a rt m e n t
9 . Talk Bu t to n
10. Call Bu t to n
11. Channel Se l e ct Bu t to n
12 . Ba t te ry Ch a rge Pa d s
13 . M ode Key
14 . Key Loc k
1 1
1 3
1
9
1 0
1 0
Our Thanks to You
Thank you for purchasing the Cobra microTALK
2-way Radio. Properly used, this Cobra product
will give you many years of reliable service.
Customer Support
1
8
2
1 2
2
9
3
1 1
4
1 3
5
6
1 4
6
Should you encounter any problems with the
product or not understand its many features,
please refer to this owner’s manual. If, after
referring to the manual, you still need help,
call Cobra Customer Service at 773.889.3087.
Cobra Customer Service
Live operators are available
M-F 8:00 am - 6:00 pm CST
at: 773.889.3087
Automated Technical
Assistance available 24 hours
a day,seven days a week.
E-mail questions to:
productinfo@cobraelectronics.com
Co b ra on the Wo rld Wide We b :
Frequently Asked Questions
(FAQ) can be found on-line
at:
www.cobraelectronics.com
A2
7
A3
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.