If You Think You Need Service . . . . . . . . . Back Cover
Features of This Product
• 40 CB Radio Channels
• 10 Weather Channels
• SoundtrackerTMSystem
• Instant Channel 19 and 9
• 40 Channel Scan
• Dual Watch
• Front Firing Speaker
• Channel Saver Circuitry
• Dynamic Microphone
• 9 Foot Mic Cord
• Front Panel Microphone
Connector
1
18 WX ST.NEW LAYOUT(4279)2a 8/9/00 4:25 PM Page 2
O p e r a t i o nInstallationInstallation
Mounting and
Connections
Note
The transceiver is held in the
universal mounting bracket by
two thumb screws,permitting
adjustment at the most convenient angle.
A universal mounting bracket
is supplied along with self tapping screws and star washers.
To mount the transceiver:
Mo u nting and Co n n e ct i o n s
Se l e ct a location for the tra n s ce i ver and microphone bra c ket that is co nve n i e nt for ope rat i o n .
In auto m o b i l e s,the tra n s ce i ver is usually mounte d
to the undern e ath of the dash panel,with the
m i c rophone bra c ket beside it.
1Hold the radio with mounting bra c ket in the
ex a ct location desire d.Re m ove the mount i n g
b ra c ket and use it as a te m p l ate to mark the
l ocation for the mounting scre ws.
CB Transceiver
4Co n n e ct the red lead of DC power co rd to an
a c ce s s o ry 12 volt fuse.
5Co n n e ct the orange lead to a co n s t a nt 12v fuse
( i e :c i g a re t te lighter or dire ct to bat te ry )
6Co n n e ct the black lead to the negat i ve side of
the auto m o b i l e.This is usually the chassis.Any
co nve n i e nt location with good elect ri cal co nt a ct
( re m ove paint) may be used.
O p e r a t i o n
Mounting and
Connections
Note
Before installing the CB radio,
visually check the vehicle battery connections to determine
which battery terminal,positive or negative (positive is the
larger of the two) is grounded
to the engine block
(or chassis).
7Mo u nt the microphone bra c ket on ri g ht side of
the tra n s ce i ver or near it using two scre ws sup-
2Drill nece s s a ry holes and secure mount i n g
b ra c ket in locat i o n .
3Co n n e ct the antenna cable plug to the re ce p t a-
cle marked “A N T”on the back of the unit.
p l i e d.When mounting in an auto m o b i l e,p l a ce
the bra c ket under the dash so the micro p h o n e
is readily acce s s i b l e.
8Attach the 4-pin microphone cable to recepta-
cle on front of unit and install unit in bracketsecurely.
2
3
18 WX ST.NEW LAYOUT(4279)2a 8/9/00 4:25 PM Page 4
Operation
Turning on
Your Radio
CB Antenna
No te
Co b ra loaded-ty pe ante n n a
m odels HGA 1000,HGA 1500,
and HGA 2000 are highly re commended for most installat i o n s. Consult your Co b ra dealer for further details (or see
o rder form at the back of
this boo k ) .
3 - Way Combination An te n n a s
a re available which allow ope ration of all three bands (AM-FM
& CB),using a single ante n n a .
Howeve r,use of this ty pe of
a n tenna usually results in less
than normal transmit and
re ce i ve range when co m p a re d
to a standard - ty pe "Si n g l e
Band" antenna designed for
CB only.
Tu rning on
Tu rn volume co nt rol cloc kwise to turn power on
and set the desired listening vo l u m e.
CB Ante n n a
Only a pro pe rly matched antenna sys tem will
a l l ow maximum power output.
In mobile installations (ca r s,t ru c k s,bo at s,e tc. ) ,
an antenna sys tem that is non-dire ctional should
be used.
When installed in a bo at,the tra n s ce i ver will not
o pe rate at maximum efficiency without a gro u n d
p l ate unless the vessel has a steel hull.Be fo re
installing the tra n s ce i ver in a bo at,consult yo u r
dealer for info rm ation re g a rding an adequate
g rounding sys te m .
Mi c rophone Co n n e ctor
Al l ows for co nve n i e nt re m oval of the micro p h o n e
plug when sto rage is re q u i re d.The micro p h o n e
MUST be co n n e cted to the unit at all times when in
u s e,for pro per ope rat i o n .
Sq u e l c h
This co nt rol is used to cut off or eliminate re ce i ve r
b a c kg round noise in the absence of an inco m i n g
s i g n a l . Adjust until the re ce i ver noise disappe a r s.
This will re q u i re the incoming signal to be slight l y
s t ronger than ave rage re ce i ver noise.Fu rther cloc kwise ro t ation will increase the threshold leve l
which a signal must ove rcome in order to be heard.
Only strong signals will be heard at a maximum
c l oc kwise setting.
O p e r a t i o n
Microphone
Connector
Squelch
4
5
18 WX ST.NEW LAYOUT(4279)2a 8/9/00 4:25 PM Page 6
O p e r a t i o n
Setting
Squelch
Gate closed
Gate open
Setting Squelch
Squelch is the “control gate”for incoming signals.
1 . Fullclockwise rotation closes the gate
allowing only very strong signals to enter.
2 . Fullcounterclockwise rotation opens the “gate”
allowing all signals in.
3 . To achieve the De s i red Squelch Setting (DSS),
t u rn the Squelch co nt rol co u n te rc l oc kw i s e u nt i l
you hear noise. Now turn the co nt rol c l oc kw i s e
just until the noise sto p s. This is the DSS setting.
O p e r a t i o n
Gate set to Desired
Squelch Setting (DSS)
6
7
18 WX ST.NEW LAYOUT(4279)2a 8/9/00 4:25 PM Page 8
O p e r a t i o n
Channel
Selection
Channel 9/
Channel 19
CB Weather
Set CB or W XMod e
Set on CB mod e. Ro t ate channel knob cloc kw i s e
u ntil desired channel is displaye d.
Channel 9/Channel 19
Press CH 9/19 to obtain instant access to emerg e n cy
channel 9.Press again for info rm ation CH 19.
PRESS AND RELEASE
C B / We at h e r
CB mode is for normal CB ope rat i o n .Pre s s
C B / We ather again and select act i ve We ather channel
in your are a .
Dual Watc h
This fe at u res allows the user to scan be tween two
s e l e cted channels.
1 . Se l e ct first channel,CB mod e.
PRESS AND HOLD
2 . Press and hold DW until LED begins flashing and
beeps once.
3 . Se l e ct second channel.Press DW until LED light s
s te a dy and radio beeps tw i ce. Two channels are
n ow sto red in DW memory.
S ca n
Press and release SCAN button to act i vate CB sca n
m od e.If the radio is squelched,radio begins to sca n .
PRESS AND RELEASE
When scan is inte rru p ted by a signal,s can stops and
holds until loss of signal.Press PTT on mic to sto p
s can funct i o n . Press Scan to re s t a rt CB sca n .
O p e r a t i o n
Dual Watch
Note
The radio needs to be
squelched before DWcan
monitor both channels.
Scan
Note
On some channels squelch
setting might have to be re-set.
The SoundTracker System reduces noise while
leaving the signal intact in the reception mode.
In the transmission mode, it strengthens the signal,providing you with a significant reduction in
noise on reception and transmission.
How SoundTracker works
On Reception–
With a normal CB,distant signals fall below the
squelch level and are unintelligible.With a
SoundTracker CB,the noise level is cut by up to
90%,which increases the signal-to-noise ratio
and dramatically improves signal clarity.This also
allows you to significantly reduce the squelch
level,which greatly expands your listening range.
“Cuts Noise Coming In”
Activating Soundtracker
1 . Press the SoundTracker button on the upper
left side of front panel.A red indicator will
illuminate when the SoundTracker system is
engaged.
PUSH AND RELEASE
O p e r a t i o n
Activating
Soundtracker
USPat.No.6,038,429
On Transmission–
A SoundTracker CB strengthens the transmit signal by more effectively using the available RF
power output of the CB.The result is improved
transmission signal clarity and an expanded
transmission range.
Sh ows re l at i ve tra n s m i t ter RF output power and
input signal strength when re ce i v i n g.The LED
( L i g ht Emitting Di ode) segments glow green to
a m ber to re d...this indicates re ce i ve or tra n s m i t
a ct i v i ty.
RX / TX Indicator LED
RX indicator will light when in the re ce i ve mod e.
TX indicator lights when in transmit mod e.
Rear Pa n e l
Antenna Co n n e cto r.This female connector per-
mits connection of the transmission line cable
male connector to the transceiver.
Exte rnal Spe a ke r.The External Speaker Jack is
used for an external speaker.The external speaker should have 8-ohm impedance and be rated
to handle at least 4.0 watts.When the external
speaker is plugged in,the internal speaker is
automatically disconnected.
Powe r :This cable is permanently attached to the
radio.If you wish to remove the radio after installation,disconnect at fuse holder and ground
connector.
O p e r a t i o n
Antenna
Connector
External
Speaker
Note
Co b ra external spe a kers are
ra ted 15 wa t t s
Power
When we ather channel is selecte d,WX indicator is
i l l u m i n ate d, and the channel is displaye d.
When using the unit with ciga re t te adapte r , turn off when
not in use to avoid draining
the batte ry.
Temporary
Mobile
Operation
Note
Red and Orange wires are co nn e cted to po s i t i ve side of soc ke t
ce n ter tip.Black wire is co n n e cted to negative side co n t a ct s.
Note
Radio resets to CH 9 when co nn e cted to cigare t te lighter plug.
Ignition Noise Inte rfe re n ce
Use of a mobile re ce i ver at low signal levels is normally limited by the pre s e n ce of elect ri cal noise.
Under most ope rating co n d i t i o n s,when signal
l evel is adequate,the backg round noise does not
p re s e nt a serious pro b l e m .Al s o,when ext re m e l y
l ow level signals are being re ce i ve d,the tra n s ce i ve r
m ay be ope rated with vehicle engine turned off.
The unit re q u i res ve ry little curre nt and there fo re
will not significa ntly discharge the vehicle bat te ry.
Even though this radio has an auto m atic noise limi te r,in some installations ignition inte rfe re n ce may
be high enough to make good co m m u n i cat i o n s
i m po s s i b l e.Consult your CO B RA dealer or a 2-way
radio technician for help in locating and co rre ct i n g
the source of seve re noise.
Te m po ra ry Mobile Ope rat i o n
For te m po ra ry mobile ope rat i o n ,you may wa nt to
p u rchase an additional cigare t te lighter adapte r
f rom your CO B RA dealer.This adapter and a magnetic mount antenna allow you to quickly "install"
your tra n s ce i ver for te m po ra ry use.
O p e r a t i o n
Operating Procedure to Receive
1 . Be sure that power cord,antenna and microphone are connected to the
proper connectors before proceeding further.The weather switch should
be in the "CB" position.
2 . Turn the radio ON by rotating the VOLUME CONTROL clockwise.
3 . Rotate SQUELCH CONTROL counterclockwise until incoming signal is
heard.
4 . Select the desired channel.
5 . Set VOLUME CONTROL to a comfortable listening level.
6 . Engage the SoundTracker system by depressing the button labeled ST.
Listen to the background noise from the speaker.Turn the SQUELCH CONTROL slowly clockwise until the noise JUST disappears (no signal should be
present).Leave the control at this setting.The squelch is now properly
adjusted.The receiver will remain quiet until a signal is actually received.Do
not advance the control too far,or some of the weaker signals will not be
heard.The revolutionary SoundTracker system allows you to reduce
unwanted background noise (static) and increase the signal for better
reception.
Operating Procedure toTransmit
1 . Select the desired channel.
2 . The receiver and transmitter are controlled by the press-to-talk switch on
the microphone.Press the switch and the transmitter is activated;release
switch to receive.When transmitting (on a clear channel),hold the microphone two inches from the mouth and speak clearly in a normal voice.
Be sure the antenna is properly connected to the radio before transmitting.Prolonged transmitting without an antenna,or a poorly matched
antenna,could cause damage to the transmitter.
Your COBRA CB transceiver is specifically
designed for the environment encountered in
mobile installations.The use of all solid state circuitry and its light weight result in high reliability.Should a failure occur,however,review the following,then if necessary,replace parts only with
identical parts.Do not substitute.
1 . Check connections to the source of power and
make sure it is the 13.8 VDC required to operate your radio.
2 . Check the fuses in the DC power cord.The
main power lead (red & orange wire) has a 2
amp 3AG type fuse in its holder.Use only the
above specified type and size fuse for maximum protection.Failure to do so,will void the
warranty.
3 . Ma ke ce rtain the microphone is pro pe rl y
plugged in.
4 . Make certain the antenna is properly assem-
bled and connected.
If you are unable to correct the problem, refer to
the SERVICE INSTRUCTIONS at the end of this
manual for the correct procedure for warranty
and post-warranty service from COBRA.
ReplacementWarning
Replacement or substitution of certain parts with
replacements other than those recommended by
Cobra may be a violation of the technical regulations of Part 95 of the FCC rules,or of Type
Acceptance requirements of Part 2 of said rules.
When making adjustment s,be sure to re - re a d
a p p l i cable po rtions of this instru ction manual to
m a ke ce rtain you are fo l l owing co rre ct proce d u re
and that the radio was pro pe rly installed,e tc.
A Few Rules That Should Be Obeyed
1. You are not allowed to carry on a conversation with
another station for more than five minutes at a time without taking a one-minute break to give others a chance to
use the channel.
2. You are not allowed to blast others off the air by overpowering them with illegally amplified transmitter power or
illegally high antennas.
3. You can't use CB to promote illegal activities.
4. You are not allowed to use profanity.
5. You may not play music in your CB.
6. You may not use your CB to sell merchandise or profes-
sional service.
Use Channel 9 For Emergency Messages Only
The FCC gives the following examples of permitted and prohibited types of communications for
use on Channel 9.These are guidelines and are
not intended to be all-inclusive.
Permitted:"A tornado sighted six miles of town."
Not Permitted :"This is observation post number 10.
FREQUENCY RESPONSE . . . . . . . . . . . .300 – 3000 HZ AT -6 dB
F requency Ranges
The CO B RA 18 WX ST II tra n s ce i ver re p re s e nts one of
the most adva n ced AM two - way radios used as a Cl a s s
D station in the Ci t i zens Radio Se rv i ce.This unit fe at u re s
a dva n ced Phase Lock Loop (PLL) circ u i t ry prov i d i n g
co m p l e te cove rage of all 40 CB channels and all 10
we ather channels as shown be l ow.
COBRA ELECTRONICS CORPORATION warrants that its
COBRA CBTransceiver,and the component parts thereof, will
be free of defects in material and workmanship for a period
of two (2) years from the date of consumer purchase.This
warranty may be enforced by the first consumer purchaser,
provided that the product is utilized within the U.S.A.
COBRA will,without charge,repair or replace,at its option,a
defective CBTransceiver upon delivery to the COBRA factory
Service Department,accompanied by proof of the date of
first consumer purchase,such a duplicated sales receipt.
You must pay initial shipping charges required to ship the
product for warranty service,but the return charges will be
at COBRA’S expense,if the product is repaired or replaced
under warranty.
Exclusions:This limited warranty does not apply;1) to any
product damaged by accident;2) in the event of misuse or
abuse of the product or as a result of unauthorized alter ations or repairs;3) if the serial number has been altered,
defaced or removed;4) if the owner of the product resides
outside the U.S.A.
All implied wa rra nt i e s,including wa rra nties of merc h a nt a b i l i ty and fitness for a particular purpose are limite d
in duration to the length of this wa rra nty.
CO B RA shall not be liable for any incident a l ,co n s e q u e nt i a l
or other damages;i n c l u d i n g,without limitat i o n ,d a m a g e s
resulting from loss of use or cost of installat i o n .
Some states do not allow limitations on how long an
implied wa rra nty lasts and/or do not allow the exclusion or
l i m i t ation of incidental or co n s e q u e ntial damages,so the
a bove limitations may not apply to yo u.
2 5 1 - 1 9 9 - 9 - 0 0 1 Re p l a ce m e nt Mo u nting Bra c ke t$ 4 . 5 0
634-081-9-001 Replacement Thumb Screws$0.60
741-080-9-001 Replacement Microphone Bracket$0.45
HG A10002 1 ”Base Loaded Magnetic Mo u nt Ante n n a$28.95
HG A15003 8 ”Base Loaded Magnetic Mo u nt Ante n n a$46.95
HG A20005 4 ”Base Loaded Magnetic Mo u nt Ante n n a$99.95
Shipping & Handling
Amount of Shipping/
OrderHandling
$25.00 and under $4.75 minimum
$25.01-$40.00$6.95
$40.01-$80.00$9.00
$80.01-$120.00$10.00
$120.01-$160.00 $11.50
$160.01 and up$14.25
For AK,HI and PR please add
an additional $15.00 for UPS
shipments.
For credit card orders fill out order form
and fax to: 1.773.622.2269
or call 1.773.889.3087
(Press 1 from the main menu)
8:00 am - 8:00 pm,M-F,CST.
Ma ke check or money order (no stamps)
payable to:
Cobra Accessories Dept.
6500 West Co rtland St .Ch i ca g o,IL 60707
HG M844 Pin Premium No i s e - Ca n celling Mi c ro p h o n e $74.95
HG M84W4 Pin Premium No i s e - Ca n celling Mic Wood gr $74.95
HG M855 Pin Premium No i s e - Ca n celling Mi c ro p h o n e $74.95
HG M73
HG M75 Power Microphone $25.95
HG M77Noise Canceling/Power Microphone$30.95
HG S100Dynamic External Speaker$21.95
HG S300Noise Canceling External Speaker$28.95
HG S500Dynamic Noise Canceling
HG A300Fi be rglass Whip Re p l a ce m e nt Ante n n a $28.95
HG A400Fi be rglass Whip Re p l a ce m e nt Ante n n a $29.95
HG A450Fi be rglass Whip Re p l a ce m e nt Ante n n a $30.95
HG A60006 2 ”Ce nte r - Load Re p l a ce m e nt Antenna
Cobra Electronics Corporation
6500 West Cortland Street
Chicago, IL 60707
18 WX ST II
O pe rating Instru ctions for your
If You Think You Need Service
For te c h n i cal assistance,please call our Au to m a ted Help Desk which can assist
you by answering the most fre q u e n t ly asked questions about Co b ra prod u ct s.
(773) 889-3087
24 hours a day,7 days a week.
A Consumer Service Representative can be reached through this same number
8:00 am - 6:00 pm,Monday through Friday,Central Standard Time.
Technical assistance is also available on-line in the Frequently Asked Questions (FAQ)
section at www.cobraelectronics.com or by e-mail to productinfo@cobraelectronics.com
If you think you need service call 1.773.889.3087
If your product should require factory service please call Cobra first before sending in your unit.
This will ensure the fastest turn-around time on your repair.
You may be asked to send your unit to the Cobra factory.It will be necessary to furnish the following in order to have the product serviced and returned.
1. For Warranty Repair include some form of proof-of-purchase,such as a mechanical reproduction
or carbon of a sales receipt. If you send the original receipt it cannot be returned.
2. Send the entire product.
3. Enclose a description of what is happening with the unit.Include a typed or clearly print name
and address of where the unit is to be returned.
4. Pack unit securely to prevent damage in transit. If possible, use the original packing material.
5. Ship prepaid and insured by way of a traceable carrier such as United Parcel Service (UPS) or First
Class Mail to avoid loss in transit to: Cobra Factory Service, Cobra Electronics Corporation,6500
W.Cortland St.,Chicago,IL 60707.
6. If the unit is in warranty,upon receipt of your unit it will either be repaired or exchanged
depending on the model. Please allow approximately 3 to 4 weeks before contacting us for
status.If the unit is out of warranty a letter will automatically be sent informing you of the
repair charge or replacement charge.If you have any questions, please call 1.773.889.3087
for assistance.
The Ci t i zens Band lies be tween the shortwave bro a d ca s t
and 10-meter Am ateur radio bands,and was established
by law in 1949. The Class D two - way co m m u n i cat i o n s
s e rv i ce was opened in 1959.(CB also includes a Class A
2
1
3
4
c i t i zens band and Class C re m o te co nt rol fre q u e n c i e s. )
F CCR e g u l at i o n s
F CC re g u l ations pe rmit only "transmissions" (one-party
to another) rather than" bro a d cast" (to a wide audience ) .
Th u s,a dve rtising is not allowed on CB channels be ca u s e
t h at is "bro a d ca s t i n g " .
F CC Wa rn i n g s
All tra n s m i t ter adjustments other than those supplied
by the manufact u rer as fro nt panel ope rating co nt ro l s,
must be made by,or under the supe rvision of,the holder
of an FCC-issued general Ra d i o - Telephone Ope rato r’s
L i ce n s e.
Re p l a ce m e nt or substitution of tra n s i s to r s,regular diodes or other parts of a unique nat u re,with parts other
than those re commended by Co b ra ,m ay cause violat i o n
of the te c h n i cal re g u l ations of Pa rt 95 of the FCC Ru l e s,
or violation of Ty pe Ac ce p t a n ce re q u i re m e nts of Pa rt 2
of the Ru l e s.
You should read and understand Pa rt 95 (included with
this unit) of the FCC Rules and Re g u l at i o n s,be fo re ope rating your Co b ra ra d i o,even though the FCC no longer
re q u i res you to obtain an ope rato r’s lice n s e.
Wh at’s included with your CB Ra d i o :
1 . CB tra n s ce i ve r6 . F CC ru l e s
5
2 . Mi c ro p h o n e.(not pict u re d )
3 . Tra n s ce i ver bra c ke t1 .
4 . Mi c rophone bra c ke t
1 6 . Antenna Connector
1 7 . External Spe a ker Co n n e cto r
1 8 . Power Cord
15
17
18
1 4
1
1 3
1 2
9
1 0
1 1
23 4 5
16
Our Thanks to You
Thank you for purchasing the Cobra 18 WX ST II
CB Radio Transceiver.Properly used,this Cobra
p rod u ct will give you many years of reliable serv i ce.
8
7
6
“Cuts Static coming in,adds Punch going out!”
Technology that dramatically improves the
transmission and reception of CB radio signals.
The revolutionary SoundTrackerTMSystem reconfigures the transmission signal which allows it to
be transferred more effectively through cluttered
airwaves.
At the same time,it significantly reduces the
amount of static on all incoming CB signals.
The end result is a clearer,cleaner sounding
reception of signals and a more powerful
transmission which dramatically improve
CB communications.
Customer Support
Should you encounter any problems with this
product,or not understand its many features,
please refer to this owner’s manual.If,after referring to the manual, you still need help,call Cobra
Customer Service at 773.889.3087.
Cobra Customer Service
Live operators are
available
M-F 8:00 am – 6:00 pm
Central StandardTime at
773.889.3087
Automated Technical
Assistance available 24
hours a day,seven days a
week.E-mail questions to:
productinfo@
cobraelectronics.com
Cobra on the World Wide
Web:Frequently Asked
Questions (FAQ) can be
found at:
w w w. co b ra e l e ct ro n i c s. co m
A2
A3
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.