Cobra Automotive G100, G300 Complete Instructions
G100 - G300
ISTRUZIONI COMPLETE
COMPLETE INSTRUCTIONS
ISTRUZIONI COMPLETE G100-G300
2
1 - LEGENDA E CONTENUT O DEL KIT .
Codice ricambio
Spare part code: 4T2771B2G
8772
Centralina
Central unit
Centrale
Centralita
Central
Злекфспнйкьт егкЭцблпт
Centrální jednotka
Styrenhet
Sentralenhet
Central
Cablaggio
Wiring harness
Câblage
Cableado
Conjunto de fios
КблщдЯщуз
Kabelá
Kablar
Ledningsnett
Kabler
Sacchetto accessori
Fittings bag
Sachet des accessoires
Bolsa de accesorios
Saco de acessórios
УбкЯдйп ме боеупхЬс
Sáèek p
isluenstvím
Tillbehörspåse
Pakke med monteringsdeler
Pose med tilbehør
Sensori ultrasuoni
Sensor transducers
Capteurs à ultrasons
Sensores a ultrasonido
Detectores de ultra-sons
БйуизфЮсбт хресЮчщн
Ultrazvukové snímaèe
Ultraljudssensorer
Ultralydsensorer
Ultralydsfølere
Sirena autoalimentata
Siren with backup battery
Sirène autoalimentée
Sirena autoalimentada
Sirene auto-alimentada
Бхфпфспцпдпфпэменз уейсЮнб
Siréna s nezávislým napájením
Självförsörjande sirén
Sirene med selvmatingsbatteri
Sirene med batteri
Sirena non autoalimentata
Siren without backup battery
Sirène non autoalimentée
Sirena no autoalimentada
Sirene não auto-alimentada
Мз бхфпфспцпдпфпэменз уейсЮнб
Siréna bez vlastního napájení
Ej självförsörjande sirén
Sirene uten selvmatingsbatteri
Sirene uden batteri
Pannello di controllo
Control panel
Tableau de commande
Panel de control
Painel de controlo
РЯнбкбт елЭгчпх
Ovládací panel
Kontrollpanel
Kontrollpanel
Styrepanel
Manuale utente/installatore
User/installation manual
Manuel utilisateur/Installateur
Manual del usuario/instalador
Manual de uso/instalação
ЕгчейсЯдйп чсЮуфз
Návod pro
uivatele/instalatéra
Användar-/installattionshandbok
Brukermanual/installatørmanual
Bruger-/installatørmanual
Pin Code Card
Pin Code Card
Carte Code PIN
Tarjeta de código PIN
Cartão do código PIN
Pin code card
Karta s pin kódem
Pin code card
PIN-kodekort
Pin-kode card
Vetrofania
Warning sticker
Vitrauphanie
Calcomanía de advertencia
Aviso autocolante
Бхфпкьллзфб гйб фб фжЬмйб
Fólie na sklo s upozornìními
Varningsetikett
Advarselssticker
Advarselsmærkat
Staffa
Bracket
Patte de fixation
Estribo
Presilha
ВсбчЯпнбт
Tømen
Bygel
Bøjle
Bøjle
Dima di foratura
Drilling mask
Gabarit de perçage
Escantillón para perforar
Escantilhão para perfuração
Елбумб фсхрЮмбфпт
Vrtací ablona
Borrningsmall
Hullmal
Hulskabelon
Driver card
Driver card
Carte de circuit de commande
Driver card
Cartão do condutor
Driver card
Driver card
Driver card
Driver card
Driver card
Radiocomando
Radio controls
Radiocommande
Radiomando
Comando por rádio
Фзлечейсйумьт
Rádiové ovládání
Fjärrkontroller
Fjernkontroller
Fjernbetjeninger
Cablaggio sirena
Siren wiring harness
Câblage sirène
Cableado de sirena
Conjunto de fios da sirene
КблщдЯщуз уейсЮнбт
Kabelá sirény
Sirénkablar
Ledningsnett sirene
Sirenekabler
www.cobra-at.com
ISTRUZIONI COMPLETE G100-G300
3
3
3
3
3
33
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
C
O
N
TEN
UTO
D
EL K
IT
KIT CO
N
TEN
TS
AKG 368
AKG 198
3
3
3
3
AKG 193 AKG 363
ACG 196
ACG 366
3
3
3
3
3
3
3
3
3
3
3
3
33
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
w
w
w
.
c
o
b
r
a
-
a
t
.
c
o
m
COMPLETE INSTRUCTIONS
G100-G300
40
Dear Customer,
Thank you and congratulations for choosing our product. It is a technologically
advanced alarm system which meets the performance standards set by automobile
manufacturers and complies with the European directives.
After the system was installed, dear Customer, you were given the radio controls or
Driver Card (where foreseen) and the user’s manual, which also contains the product’s
declaration of conformity and the relative installation certificate.
The manual is divided into 22 parts:
Page
2/3 _______ LEGENDA AND KIT CONTENTS.
41 ______
INFORMATION.
42 ______
INTRODUCTION.
43 ______ ADDITIONAL PROTECTIONS.
44/45 ______
LIST OF FUNCTIONS.
da 46 a 50 ______ LIST OF STANDARD FUNCTION (G300) AND
SELF-LEARNING PROCEDURE.
51/52 ______ LIST OF BASIC PROGRAMMABLE FUNCTIONS.
da 52 a 55 ______ LIST OF ADVANCED FUNCTIONS (programmable).
56/57 ______ SYSTEM COMPONENTS.
57 ______
VEHICLE SPEED SENSOR CONNECTION -VSS (G100-G300).
AUXILIARY OUTPUT AUX2.
58/59 ______ PROGRAMMING.
60 _______ RADIO CONTROL FUNCTIONS CHECK
.
da 61 a 66 ______
PROGRAMMABLE FUNCTIONS (G100 -G300).
67/68 ______ HOW TO PROGRAMME THE (G100 - G300) SYSTEM.
68/69 ______
PROCEDURE FOR ADDING NEW RADIOCONTROL DEVICES (G100)
AND NEW DRIVER CARDS (G300).
SWITCHING ON / SWITCHING OFF OF DRIVER CARD.
70 ______
ALARM MEMORY.
71 ______
EMERGENCIES, PERSONALIZING THE PIN CODE.
72/73 ______ MAINTENANCE TROUBLESHOOTING
.
74 ______ SYSTEM TECHNICAL CHARACTERISTICS.
da 75 a 98 ______
DIAGRAMS AND GUARANTEE.
Please read the manual carefully to get the full benefit of the product purchased.We also
advise you to keep this manual in the same place as your car documents for easy consultation
when needed.If any problem arises that cannot be resolved, please contact your dealer.
GB
COMPLETE INSTRUCTIONS
G100-G300
41
www.cobra-at.com
STICK ON PIN
CODE LABEL
PERSONAL PIN CODE
5CGXXXAIA
S/N 0003 050524
PIN
CODE
1122
2 - INFORMA TION.
The system is equipped with a self-learning function which makes it possible to simplify
all operations necessary for adding or replacing radio controls / Driver Cards but only
with the user’s consent.
For the procedure make reference to the manual at page 69 on www.cobra-at.com
2.1 - Personal PIN CODE.
Each G100 - G300 system has a PIN code that is used to disarm the system in
emergencies.
This is a PIN CODE CARD sample
(PIN CODE is a factory-setted):
We advise you to stick the PIN CODE adhesive label onto the PIN
CODE card (which may be found on the rear of the control unit).
COMPLETE INSTRUCTIONS
G100-G300
42
3 - INTRODUCTION.
These anti-intruder alarm systems are controlled by a radio control device - G100 or
G300 - with Driver Card with high security codes. This technology provides an extremely
high degree of protection against any attempt to reproduce the code.
The radio control makes it possible to activate the system from a distance of 5 - 10
metres from the vehicle, while the drivers card transmits from a distance of 1 - 5
metres from the vehicle.
In some circumstances the range may be shorter due to interference from other
sources (e.g. radio transmitters operating on the same band).
If the radio control is not effective in the usual range, get as close to the vehicle as
you can.
If radio - controlled window closing is foreseen, we advise you to stay very close to
the vehicle when carrying out this operation to make sure it is performed under safe
conditions.
Your vehicle’s complete protection is assured by:
Mod.
AKG 198
AKG 368
VOLUMETRIC
PROTECTION
PERIMETRIC
PROTECTION
WIRING CUT
PROTECTION
AKG 193
ACG 196
ACG 366
AKG 363
ENGINE LOCK
PROTECTION
Note: in product G366 (without us) the perimeter connection must only be made
on the door pushbutton connection.
COMPLETE INSTRUCTIONS
G100-G300
43
4 - ADDITONAL PROTECTIONS (G100-G300).
You can increase the protection level of the system with the following additional sensors:
5452: Level monitor module.
When the system is armed, this sensor will detect the vehicle being jacked up to tow it
away or steal the wheels.
5462: Hyperfrequency module.
When the system is armed, hyperfrequency emissions from the module hidden in the car
will ensure volumetric protection of the vehicle.
2980: Windows lift module.
The electric windows of your car will raise automatically when the system is armed.
COMPLETE INSTRUCTIONS
G100-G300
44
5 - LIST OF FUNCTIONS.
5.1 - Standard functions list.
The following list indicates the main functional characteristics of the alarm system.
G100
• Radiocontrol button functions.
• Arm / Disarm by means of dynamic - code radio controls.
• Disablement of the sensor transducer and / or external sensor.
• Panic alarm.
G300
• Arm / disarm controls self - learning procedure.
• Arm by means of the vehicle’s original radio controls
• Driver card armed / disarmed .
• Disablement of the sensor transducer and / or external sensor.
• Driver card functions.
G100 - G300
• Volumetric protection of the vehicle’s interior by ultrasonic sensor not requiring sensitivity
adjustment.
• Perimetric protection. When the alarm is armed, after 25 s the siren will sound if a door
or the bonnet or boot is opened.
• Protection of start attempts. With the alarm connected the engine is blocked and a start
attempt generates an alarm.
• When an alarm occurs the siren sounds for 30 s. The direction lamps flash.
• Emergency disarming by pin-code.
• Wire-cutting protection.
• Original centralised door and boot closing system.
• LED indicating the system’s status with alarm-record memory function.
• Safety circuit to prevent the system being armed when the engine is running.
• Coupling of modules / siren 4310 / satellite alarm ICD31 on Cobra Bus line.
5.2 - List of basic functions (programmable).
These are the functions that require programming in keeping with the vehicle model and
desired operating characteristics of the alarm system. Please refer to the basic functions
table in the programming tables section.
G100
• Centralised closing times.
• Controlled comfort window closing.
• Silent arming.
• Armed/disarmed blinker
COMPLETE INSTRUCTIONS
G100-G300
45
G100 - G300
• Door / bonnet / boot open signal.
.• Automaticsystem arming.
• Automatic start prevention arming (starter).
• Start prevention alarm.
5.3 - List of advanced functions (programmable).
These are special functions that require programming in keeping with the desired operating
characteristics of the alarm system. Please refer to the advanced functions table in the
programming tables section.
G100
• Autolock - Automatic door locking.
• Autolock - AMERICAN STYLE.
• AutoHazard (switching on indicator lights in the case of emergency braking).
• Door closing by anti-diversion alarm.
• Car Finder.
• Automatic anti - theft protection.
•· Voluntary anti - theft protection.
• Trunk Release (truck opening).
.
G300
• Automatic anti - theft protection.
•· Voluntary anti - theft protection.
G100 - G300
• Automatic anti - theft protection delay with odometer.
• Pager output.
• Anti - diversion blocker.
• Anti - diversion alarm.
• Buzzer.
• Speed limit signal.
COMPLETE INSTRUCTIONS
G100-G300
46
B
A
B
A
6 - LIST OF ST ANDARD FUNCTIONS (not programmable).
G100
RADIOCONTROL BUTTON FUNCTIONS (G100).
Button A
This button arms the alarm and blocker system, deactivates
the volumentric input and additional sensors input,
activates the panic option, gives access to the
programming function, selects the line and raises the
buzzer volume in the programming table, and activates the
Car Finder option.
Button B This button deactivates the alarm, block system,
activates/deactivates the function and lowers the
buzzer volume.
6.1 - Arming.
• When radiocontrol button “A” is pressed, the doors lock (if the
vehicle is equipped with a centralized locking system).
•
The direction lights flash twice.
•
The buzzer emits two acoustic signals (if enabled).
• The protection functions activate after 25 s.
• The LED lights up and stays on for 25 s, then flashes.
6.2 - Disarming.
• When radiocontrol button “B” is pressed, the doors
unlock.
• The direction lights flash once.
• The buzzer emits one acoustic signal (if enabled).
• The protection functions are immediately deactivated.
• The LED is switched off.
B
A
B
A
COMPLETE INSTRUCTIONS
G100-G300
47
6.3 - Interrupting an alarm during the warning-signal cycle.
While the system is sounding the alarm it is possible to deactive the siren
and flashing lights by pressing radio control button “B” once (one press).
This operation interrupts the alarm cycle, but the system stays armed. To
deactivate the system completely, it is necessary to disarm it by pressing
radiocontrol button “B” again (two presses).
B
A
B
A
RADIOCONTROL FUNCTIONS
Button
A
Button
B
Arming
Disarming
Interrupt alarm
Panic alarm
Deactivate ultrasonic volumetric
sensor and additional sensor
(if installed)
Car finder
6.4 - Deactivating the ultrasonic volumetric sensor .
If you wish to activate the protection system with the windows left open or
when a passenger will be staying inside the passenger compartment, it is
possible to deactivate the volumetric sensor so that it will not generate any
alarms.
1) Activate the system by pressing radiocontrol button “A”.
2) Press radiocontrol button “A” again within 25 s.
If a hyperfrequency or anti-lifting sensor is installed, it is possible to disable
it by pressing button “A” twice within 25 s. The reception of the signal is
confirmed by one flash of the direction indicators and by an acoustic signal
from the buzzer (if enabled). The sensor has been disabled; all the other
protection functions remain active. The sensors will be automatically
reactivated the next time the system is armed
B
A
COMPLETE INSTRUCTIONS
G100-G300
48
6.5 - Panic Alarm.
Whenever you press radiocontrol button “A”, provided 25 s have elapsed after arming
the system, it will produce an alarm cycle (siren sound and flashing direction lamps). If
the Car Finder function is enabled, press radiocontrol button “A” twice (2 consecutive
presses). To stop the panic alarm, press radiocontrol button “B.
G300
INTRODUCTION.
This alarm system can self-learn a series of recurrent signals that take place on the
vehicle when the operations for locking and unlocking the doors are executed the original
radio control device. The signals that are normally utilised are the engine comand, door
deflector status and direction indicator signals. If connection to the direction indicators is
foreseen for alarm activation/deactivation, please note that:
• the alarm may not activate / deactive when the vehicle’s emergency blinker is
on.
6.6 - Arm / disarm controls self - learning procedure.
For self-learning of the arm / disarm commands through the vehicle’s original radiocontrol
device, the following conditions are indispensable:
1) G300 system disarmed.
2) Door and bonnet closed.
3) Ignition off (+15 absent).
Proceed as described:
A) Connect the GREY - BLACK lead to Ground (GND) for at least 1 s.
B) The LED will start to flash slowly.
C) Press the Lock (close) button on the vehicle’s original radiocontrol.
D) The LED flashes fast while awaiting the door opening signal.
E) Press the Unlock (open) button on the vehicle’s original radiocontrol device for
the system disarmed signal.
F) The confirmations of the happened self-learning process of the signal is
confirmed by an acoustic signal emitted by the buzzer.
COMPLETE INSTRUCTIONS
G100-G300
49
6.7 - Arming
6.7.1 Arm by means of the vehicle’s original radio controls
• When the lock button on the original radiocontrol is pressed, the doors lock and
the system is armed.
•
The buzzer emits two acoustic signals (if enabled).
• The LED lights up and stays on for 25 s, then flashes.
• The protection functions activate after 25 s.
6.7.2 Arm with Driver Card
It is also possible to connect the alarm system in the event of an emergency by pressing
the button on the Driver Card, without locking the doors.
6.8 - Disarming (using the Driver Card).
Introduction: the alarm is disconnected using the vehicle’s original remote control and by
recognition of the Driver Card as follows:
6.8.1 -
original radiocontrol recognition procedure.
•
Press the original radiocontrol button to unlock the doors.
•
The direction lights flash
(“pre - disarm” phase).
•
The protection functions are temporarily deactivated while awaiting the
Driver Card signal.
• The buzzer emits an acoustic signal (if enabled). Once the Driver Card
has been recognised, the LED switches off.
Note: it is also possible to disarm the alarm system in the event of an emergency by
pressing the button on the Driver Card, without unlocking the doors.
6.9 - Deactivating the ultrasonic volumentric sensor .
If you wish to arm the protection system with the windows lift open or when a
passenger will be staying inside the passenger compartment, it is possible to deactivate
the volumetric sensor so that it will not generate any alarms.
• Within 5 s after having turned off the ignition and from the door opening, keep the
button pressed down until you see the LED give a long flash. If a hyperfrequency
or anti-lifting sensor is installed, it is possible to disarm it by pressing the button
again within 5 s after the LED has flashed. The LED will flash again to confirm its
deactivation.
• Arm the system by pressing the radiocontrol button: the sensors are deactivated
but all the other protections are active. The sensors will be automatically reactivated
the next time the ignition is turned on.
COMPLETE INSTRUCTIONS
G100-G300
50
6.10 - Driver card Function.
The Driver Card is used exclusively for the user recognition phase:
When the doors are unlocked by the vehicle’s original radiocontrol the system goes into a
“pre-disarm” phase which lasts for 25 s, activated by the opening of a door.
When 25 s have elapsed after the door opened, unless Driver Card recognition has
occurred an alarm state is generated. It is possible to disarm the system during the alarm
phase using the Driver Card key or by keying in the entire Pin Code from the LED panel
(see page 72).
G100 - G300
6.1 1 - Protection functions.
When the system is armed, opening the bonnet/boot/door or attempting to start the vehicle
generates an acoustic and visual alarm cycle that lasts approximately 30 s. In products
that include a volumetric sensor, the alarm will be triggered off by intrusion into the
passenger compartment. At the cycle’s end the system stays armed.
6.12 - Coupling of modules / siren 4310 / satellite alarm ICD31 on Cobra Bus
line.
On the Cobra Bus line (pin 14) it is possible to connect the following additional modules
(Siren 4310 / anti-lifting module / satellite alarm ICD 31 / Engine lock 8509) by means of the
following programming procedure:
1. Disconnect system.
2. Enter programming mode using the dedicated procedure for the product.
3. Move from page 1 to page 7 by activating and de-activating the panel (+15 ON /
OFF).
4. The storage and completion of programming is signalled by flashing indicator
lights.
Repeat from point 1 if a module of the Cobra Bus line is disconnected.
NOTE: with the alarm disconnected, disconnecting a self learning module from
the Cobra Bus line, when the G100/G300 is armed the indicator lights will flash
8 times and if the Buzzer is activated it will signal 8 times by the buzzer.
A TTENTION!
If both radiocontrol devices (G100) or Driver Card (G300) have been lost, proceed
as follows:
A. Disarm the system by keying in the PIN code.
B. Cut off the system’s power feed (disconnnect the connector from the central
unit).
C. Open a door and the vehicle’s bonnet.
D. Turn on the ignition.
E. Reconnect the power feed.
COMPLETE INSTRUCTIONS
G100-G300
51
F. Key in the PIN code.
G. The LED will confirm with a long flash that the code you have entered is
correct.
H. After about 5 s the LED will light up with a steady light and by 5 flashes from the
direction indicators to signal that you have entered the self-learning procedure.
I. Ref. subsection 16.1 point 7 and 16.2 the point 8 of the procedure for adding on
new radiocontrol / Driver Card devices for all the transmitters to be enabled.
Note: When a new remote control / Driver Card is coupled, the system automatically
prevents use of the previous ones. They can only be used if they are re - enabled through
the self-learning procedure.The system can memorize up to a maximum of 4 radiocontrol
devices (G100), or 4 Driver Cards (G300).
7 - LIST OF BASIC FUNCTIONS
As the functional characteristics of this system can be personalised, the installer will
have clearly marked in this manual which of them are enabled. The standard factory
setting is the one indicated by a dark square.
G100
7.1 • Controlled comfort window closing.
When arming, if radio control button “A” is kept pressed down the windows close in
controlled comfort mode. This makes it possible to stop the window rising by releasing the
button.
7.2 • Window control delay activation.
If radiocontrol window output is enabled, when this function is activated the windows
will rise with a delay of 1 s after closing the doors.
7.3 • Silent arming.
For temporary elimination of the buzzer signal when arming the system, press radiocontrol
button “A” before turning off the ignition. The next time it is armed, the buzzer will start
working again.
7.4 • Armed / Disarmed blinker.
The system signals it has been armed with two blinks of the direction lamps, and signals
that it has been disarmed with one blink. If this function is disabled, the direction lamps
blink only when an alarm cycle is triggered.
Disabled
Enabled
Disabled
Enabled
Disabled (G300)
Enabled (G100)
Loading...