Cobra PX500 User Manual

TWO-WAY RADIO MODEL

PX500PX500 Owner’s Manual

Owner’s Manual

Printed in China

Part No. KEM-ML41900

English

Nothing Comes Close to a Cobra

®

Nothing Comes Close to a Cobra

®

Before operating the radio, please read all safety and
operating instructions. Save all instructions in a safe place
for future reference.

WARNING: Important Safety Instructions

1. Only accessories included in this package or specied by the manufacturer
should be used with the radio. The 5V micro-USB charging input is compatible
with most high quality micro-USB chargers that fully conform to the USB
standards.

2. Do not use cleaners or solvents to clean the exterior of the radio. Use only a
damp or dry cloth.

3. Do not expose this product to splashing or dripping water.

4. Do not attempt to service the receiver yourself. Removing the cover will void
the warranty. Changes or modications not expressly approved by Cobra may
void the user’s authority granted by the FCC to operate this device and should
not be made.

5. Do not plug the wall adaptor into the power outlet if the outlet is wet.

6. Do not use any portable radio that has a damaged antenna. If a damaged
antenna comes into contact with your skin, a minor burn can result.

WARNING: Important Safety Instructions for Battery

Read All Instructions

• Do not incinerate the battery even if it is severely damaged or is completely worn
out.

• Do not discard battery in a re. The battery pack can explode in a re.

• Do not replace battery in any area labeled “Hazardous Atmosphere”. Any sparks
created in a potentially explosive atmosphere can cause an explosion or re.

• Do not disassemble, crush, puncture, shred, or otherwise attempt to change the
form of your battery.

• Do not dry a wet or damp battery with an appliance or heat source, such as a hair
dryer or microwave oven.

• A small leakage of liquid from the battery cells may occur under extreme usage or
temperature conditions. This does not indicate a failure. Do not open, deform or
mutilate the battery as there may be corrosive materials which can cause damage
to eyes or skin and may be toxic if swallowed.

However, if the outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If battery liquid gets into your eyes, ush them with clean water for a minimum of

10 minutes and seek immediate medical attention.

This product uses Lithium Polymer Battery. Do not transport package if damaged, a
re hazard could exist.

For more information, please call our customer support line at [phone], or
email us at [e-mail].

Recycle Battery

Local, state or federal laws may prohibit disposal of batteries in ordinary trash.
Consult your local waste authority for information regarding available recycling
and/or disposal options.

Introduction

Making Life Easier and Safer

Staying in touch is convenient and easy when using your
microTALK
include:

Communicating with others while hiking, biking, and working; keeping track of
family and friends at a crowded public event; checking with travel companions;

Holster

®

radio. Some of the many uses you will discover

connecting with neighbors; arranging meeting spots
with others while shopping at the mall, talking with
your colleagues in store or warehouse.

®

Secure your microTALK
the go.

Carrying your microTALK
using the holster.

radio while on

®

radio with you is easy when

The holster easily attaches to your belt, purse, or
backpack.

Customer Assistance

Product Service & Support

For any questions about operating this new Cobra branded product, PLEASE
CONTACT US FIRST… The contact information for support will vary depending
on the country in which you purchased and utilize the product.

To obtain warranty service or other information for products purchased from
Altis itself or through its authorized reseller or agent and utilized in the U.S.A.,
please call our consumer support line at [phone], or email us at
[e-mail]. You will receive instructions on how to ship the
products at your expense to an Altis Global Limited Authorized Service Center.
To obtain service, you must include: (a) a copy of your receipt, bill of sale or
other comparable proof of purchase; (b) a written description of the problem;
and, most importantly; (c) your address and telephone number.

For warranty and customer service information outside the US, please contact
your local dealer.

For further information needed on its features, please visit
www.cobrawalkietalkie.com for frequently
asked questions and the electronic manual.

A-1 A-2

©2018 Altis Global Limited,

Atlanta, GA USA.

www.cobrawalkietalkie.com

Customer Assistance

Operational Cautions

Exposure to high volume sound levels may cause temporary or permanent
damage to your hearing. Although there is no single volume setting that is
appropriate for everyone, you should always use your radio with the volume set
at low level and avoid prolonged exposure to high volume sound levels.

1. Set the volume control in a low position and use as low a volume as

possible.

2. Avoid turning up the volume to block out noisy surroundings. Whenever

possble, use your radio in a quiet environment with low background noise.

3. Limit the amount of time you use headsets or earpiece at high volume

levels.

4. When using the radio without a headset or earpiece, do not place the radio’s

speaker directly against your ear.

5. Observe all signs and instructions that require an electrical device or RF

radio product to be switched off in designated areas, such as gas/refueling
stations, hospitals, blasting areas, potentially explosive atmospheres, or
aircraft.

6. If you experience a skin irritation after using this product, discontinue use

and seek medical attention.

7. If the product or charger: overheats; has a damaged cord or plug; has been

dropped or damaged; has been dropped into water, disconnect any charger
from its power supply, discontinue use of the product.

Electromagnetic Interference

Nearly every electronic device is susceptible to electromagnetic interference
(EMI) if inadequately shielded, designed, or otherwise congured for
electromagnetic compatibility. Turn off your radio in any facility where posted
notices instruct you to do so. These facilities may include hospitals or health
care facilities that may be using equipment that is sensitive to external RF
energy.

• When instructed to do so, turn off your radios when on board an aircraft. Any

use of a RF device must be in accordance with applicable laws, regulations
and airline crew instructions.

• Some radios may interfere with some hearing aids. In the event of such

interference, you may want to consult your hearing aid manufacturer or
physician to discuss alternatives.

• If you use any other personal medical device, consult the manufacturer of

your deivce to determine if it is adequately shielded from RF energy. Your
doctor or physician may be able to assist you in obtaining this information.

A-3 A-4

Introduction

Product Features

1

2

3

4

5

6

1. Antenna

2. Up Button

3. Down Button

4. Microphone

5. Call/Lock Button

6. USB Charge Jack

7. Battery Door Screws

8. Speaker

1213

15

11

10

9

8

7

9. Mode Button

10. Backlit LCD Display

11. Talk Button

12. Power On/Off/Volume Knob

13. External Speaker / Microphone
Jack

14. Holster with 360˚ Swivel Clip

15. Battery compartment

14

1

Features

• 22 Channels

• 121 Privacy Codes

(38 CTCSS codes/
83 DCS codes)

• Hands-Free Operation
(VOX)

• Backlit LCD Display

• Call Alert

• Button Lock

• Speaker/

Microphone/

Charge Jack

• Roger Beep

• Battery/Power Saver

• Keystroke Tones

• Battery Level
Indicator

• Low Battery
Audible Alert

• Auto Squelch

• Holster

10

Backlit LCD Display

4

3

2

9

1. Lock Icon

2. Transmit Icon

3. Receive Icon

4. Battery Level Indicator

5. VOX Icon

6. DCS Icon

7. CTCSS Icon

8. DCS / CTCSS Privacy
Code Numbers

9. Power Saver Icon

10. Channel Numbers

Caring for Your microTALK

®

Your microTALK

radio will give you years of trouble-free service if cared for

®

Radio

properly. Handle the radio gently. Keep the radio away from dust. Never put
the radio in water or in a damp place. Avoid exposure to extreme
temperatures.

5

6

7

Installing Batteries

Holster

1. Remove Holster by releasing the belt clip latch and

1

slide the holster downward.

2. Unscrew 2 screws at bottom with a proper

2

screwdriver, then open the battery compartment
cover. Connect the connector of the battery to the

8

socket of the radio inside the battery compartment.

3. Place the battery inside the battery compartment and
align the wire as shown.

Battery Door Screws

(Make sure the wire does not block the screw holes)

4. Replace the battery compartment cover, screw down
the screws mildly.

(Screw nuts may be damaged if applying too strong

force when tightening)

Battery connector

5. Re-attach the holster

To charge batteries in radio:

Wires alignment

1. Check to see that the batteries have been
inserted properly.

2. Insert the cable into the charge jack located at
the left side of the radio.

3. Plug the cable into USB-compatible power port.

Only use the supplied rechargeable batteries and desktop charger for
recharging your Cobra microTALK

®

radio.

Cobra recommends your radio is turned off while being charged.

1 2

Operation

Using Your Radio

For charging microTALK® radio(s) in desktop charger:

1. Insert radio(s) into desktop charger as shown.

2. Insert the micro-USB cable into jack on back of charger.

3. Plug the cable into USB compatible power port.

For pluggable equipment, the socket-outlet shall be

accessible.
If charging light is not on, check position of radio. Radio should be
upright. The charge indicator light will stay on as long as the radio is in
the charging well, and the light will go off when the charging is complete.
Note: To charge a single radio, you can bypass the desktop charger and

simply insert the micro-USB’s connector directly into the charge jack
located on the left side of the radio.
The radio will display ashing battery icon while charging.
Cobra recommends your radio be turned off while being charged.

Turning on Your microTALK® Radio

Turn clockwise to turn the radio on and counterclockwise to turn the
radio off.

1. In the ON position, the radio chirps and briey shows all feature icons
available on the radio.

2. The display screen then shows the current channel, code and all features
that are enabled.

installed near the equipment and shall be easily

Quick Start

1. Turn On/Off VOL Knob clockwise to turn the radio on and counter
clockwise to turn the radio off.

2. Select a desired channel.

Both radios must be tuned to the same
channel/privacy code to communicate.

3. Press and hold the Talk button while speaking into the microphone.

4. When nished talking, release the Talk button and listen for a

response.

This radio is equipped with default Privacy Code on each
channel for minimizing unwanted signals from others. See page 6
to 8 for procedures changing your radio from default Privacy Code
to a different Privacy Code or disabling Privacy Code.

Battery Low

When battery power is low, the nal bar in the

Battery Low

Battery Low icon will blink and an audible tone will
sound twice before the radio shuts off. Your batteries
need to be recharged.

The radio will display ashing battery icon
while charging if the radio is on.

Auto Battery Save

If there are no transmissions within 10 seconds, the

Battery Save Mode

radio will automatically switch to Battery Save mode
and the Power Saver icon will ash in the display.
This will not affect the radio’s ability to receive
incoming transmissions.

Communicating with Another Person

1. Press and hold the Talk button.

Talk Button

2. Position the microphone about two inches (5 cm)
from your mouth, speak in a normal voice.

3. Release the Talk button when you are
nished talking and listen for a response.

Two Inches

You cannot receive incoming calls while

from Mouth

pressing the Talk button.

Both radios must be tuned to the same
channel and privacy code to communicate.

To Select a Channel

Up & Down Button

Press Mode button once, then press Up button or

Channel Number

Down button.

Both radios must be tuned to the
same channel to communicate.

See page 11 for frequency
allocations charts.

Listening for a Response

Listening

Release the Talk button to receive incoming
transmissions. Your microTALK
in Standby mode while the Talk or Call buttons
are not pressed.

®

radio is always

3 4

To Adjust Volume

1. Rotate clockwise to increase the volume.

2. Rotate counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an

uncomfortable level, it could hurt your ear.

Call Button

Call Button

Press and release the Call/Lock button.

The other person will hear a three second call
tone. This tone is used only to establish voice
communications.

Auto Squelch

Your microTALK
unwanted noise due to terrain, conditions limit.

Lock Function

Lock Button

The Lock function locks the Up, Down and Mode

To turn the lock on or off:

– Press and hold the Call/Lock button for
two seconds.

A double beep sound is used to conrm your lock

Lock Icon

microTALK

Your range will vary depending on terrain and

In at, open country your radio will operate at

Buildings and foliage in the path of the signal can

Dense foliage and hilly terrain will further reduce the

On Channels 8 through 14, your radio automatically

®

radio will automatically shut off weak transmissions and

buttons to prevent accidental operation.

enabled. When in Lock mode, the Lock icon will be
displayed also.

®

Range

conditions.

maximum range.

reduce the range of the radio.

range of the radio.

switches to low power, which will limit the range the
radio can communicate.

Operation

Mode Functions

Scrolling Through the Mode Function

By scrolling through the Mode function, you will be able to select or turn on
preferred features of your microTALK
Mode function, your radio features will be displayed in the same
predetermined order:

Mode Button

Channel

VOX on/off On or off shown on LCD

VOX sensitivity 5 levels

CTCSS code setting 38 codes for setting

DCS code setting 83 codes for setting

Privacy Codes

Your microTALK
that can help to reduce interference from other users on any given channel.

®

radio incorporates two advanced coded squelch systems

CTCSS (Continuous Tone Coded Squelch System) provides 38 privacy codes
and DCS (Digitally Coded Squelch) provides 83 privacy codes. This provides
a total of 121 Privacy Codes. Either system can be used on all channels, but
both systems cannot be used on the same channel at the same time.

For ease of use and reduce interference from other users, the 22 channels of
your radio has been customized, see Channel and Default Privacy Code
Table.

5 6

®

radio. When scrolling through the

22 channels with default privacy code

Channel and Default Privacy Code Table

Privacy Code

Channel
Type Number

1 CTCSS 1
2 CTCSS 11
3 CTCSS 22
4 CTCSS 33
5 DCS 1
6 DCS 11
7 DCS 22
8 DCS 33
9 DCS 44
10 DCS 55
11 DCS 66

You can change your radio to a different Privacy Codes for
working with other radio with different privacy code or without
privacy code. See page 7 and 8 for procedures.

Privacy Code
Channel
Type Number

12 DCS 77
13 CTCSS 1
14 CTCSS 11
15 CTCSS 22
16 CTCSS 33
17 DCS 1
18 DCS 11
19 DCS 22
20 DCS 33
21 DCS 44
22 DCS 55

Set CTCSS Privacy Codes

To select a CTCSS privacy code:

Mode Button

1. After selecting a channel, press the Mode button until
the CTCSS icon appears and the small numbers next
to the channel number ash on the display.

Privacy Code

If DCS is turned on at the channel selected, the
display will ash the CTCSS icon and “OFF.”
To switch from DCS to CTCSS, press the Up or
Down button while the display is ashing
“OFF.” The display will then show the small

Up/Down Button

numbers ashing and you will then be able to
proceed to step 2.

2. Press using the Up or Down button to select a privacy
code. You can hold the Up or Down button for fast
advance.

3. When your desired CTCSS privacy code is displayed, choose one of the

following:

a. Press the Mode button to enter the new setting and proceed to other

functions.

b. Press the Talk or Call/Lock button to return to Standby mode.

c. Do not press any buttons for 6 seconds to return to Standby mode.

Set DCS Privacy Codes

To select a DCS privacy code:

Mode Button

1. After selecting a channel, press the Mode
button until the DCS icon appears and the small
numbers ash on the display (00 through 83).

DCS Privacy Code

If CTCSS is turned on at the channel selected,
the display will ash the DCS icon and “OFF.”
To switch from CTCSS to DCS, press the Up

Up/Down Button

or Down button while the display is ashing
“OFF.” The display will then show the small
numbers ashing and you will then be able to
proceed to step 2.

2. Press using the Up or Down button to select a DCS
privacy code. You can hold the Up or Down button for fast advance.

3. When DCS privacy code is displayed, choose one of the following:

a. Press the Mode button to enter the new setting and
proceed to other functions.

b. Press the Talk or Call/Lock button to return to Standby mode.

c. Do not press any buttons for 6 seconds to enter the new settings
and to return to Standby mode.

To successfully communicate using a privacy code, both
the sending and receiving radios must be tuned to the same
channel and to the same privacy code system (CTCSS or DCS)
and privacy code number. Each channel will remember the
last privacy code system and number you select.

The privacy code 00 is not a privacy code, but allows all
signals to be heard on a channel that is set to 00 on both
the CTCSS and DCS systems.

7 8

Voice Activated Transmit (VOX)

In VOX mode, your microTALK

®

radio can be used “hands-free,” automatically
transmitting when you speak. You can set the VOX sensitivity level to t the
volume of your voice and avoid transmissions triggered by background noise.

Mode Button

To turn VOX mode on or off:

1. Press the Mode button until the VOX
icon shown on the display. The current On or Off
setting is displayed.

2. Press the Up or Down

VOX Icon

button to turn VOX On or Off.

3. Choose one of the following:
a. Press the Mode button to enter the
new setting and proceed to other functions.

Up/Down Button

b. Press the Talk or Call/Lock button to return to
Standby mode.

To set VOX sensitivity:

Mode Button

VOX Sensitivity Level

1. Press the Mode button until the VOX icon
ashes and the current sensitivity level is displayed.

The current VOX sensitivity level is
displayed with letters “L” and a Number 1
through 5, with Number 5 being the most
sensitive level and Number 1 being the
least sensitive level.

2. Press the Up or Down

Up/Down Button

button to change the setting.

3. Choose one of the following:
a. Press the Mode button to enter the
new setting and proceed to other functions.

b. Press the Talk or Call/Lock button to return to

Standby mode.

c. Do not press any buttons for 6 seconds to
return to Standby mode.

Call Alert

®

Your microTALK

radio can alert you to incoming signals by sounding an

audible call tone.

Roger Beep Conrmation Tone

Your listener will hear an audible tone when you release the Talk button.
This alerts the other party that you have nished talking and it is OK for
them to speak.

Key Tone

Key Tone is an audible tone which will sound each time a button is
pressed.

9 10

Operation

General Specications

Frequency Allocation and Compatibility

A = Channel No. for 22 Channel Models
B = Frequency in MHz
C = Power Output

A B C

1 462.5625 High
2 462.5875 High
3 462.6125 High
4 462.6375 High
5 462.6625 High
6 462.6875 High
7 462.7125 High
8 467.5625 Low
9 467.5875 Low
10 467.6125 Low
11 467.6375 Low
12 467.6625 Low
13 467.6875 Low
14 467.7125 Low
15 462.5500 High
16 462.5750 High
17 462.6000 High
18 462.6250 High
19 462.6500 High
20 462.6750 High
21 462.7000 High
22 462.7250 High

IMPORTANT NOTICE:

WARNING: Changes or modications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device must accept any
interference received,including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

• Consult the dealer or an experienced radio/TV technician for help.

Safety Information for microTALK

Your wireless handheld portable transceiver contains a low power transmitter. When the talk button
is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty
factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted
RF exposure guidelines with safety levels for handheld wireless devices

Important

FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the
FCC RF exposure guidelines when used with Cobra accessories supplied or designated for this
product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use
only the supplied antenna. Unauthorized antennas, modications or attachments could damage the
transmitter and may violate FCC regulations.

Normal Position

Hold the transmitter approximately 2 inches from your face and speak in a normal voice, with the
antenna pointed up and away.

FCC Part 15.21 Warning Statement­NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT

EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

IC RSS-GEN

This device complies with ISEDC license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.

Under ISEDC regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by ISEDC. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

The applicant is responsible for providing proper instructions to the user of the radio device, and any
usage restrictions, including limits of exposure durations. The user manual shall provide installation
and operation instructions, as well as any special usage conditions, to ensure compliance with SAR
and/or RF eld strength limits. For instance, compliance distance shall be clearly stated in the user
manual.

Radiation Exposure Statement:

Any Changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

For Remote controller, SAR tests are conducted using standard operating positions accepted by the
FCC/ISEDC with the device transmitting at its highest certied power level in all tested frequency
bands, although the SAR is determined at the highest certied power level, the actual SAR level of
the device while operating can be well below the maximum value.

Before a new model device is available for sale to the public, it must be tested and certied to the
FCC that it does not exceed the exposure limit established by the FCC/ISEDC, Tests for each device
are performed in positions and locations (e.g. at the ear and worn on the body) as required by the
FCC/ISEDC.

For body worn operation, this model device has been tested and meets the FCC/ISEDC RF exposure
guidelines when used with an accessory designated for this product or when used with an accessory
that Contains no metal and that positions the handset a minimum of 10 mm from the body.

Non-compliance with the above restrictions may result in violation of RF exposure guidelines.

MODEL PX500:

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: 1) This device may not cause harmful interference, and 2)
this device must accept any interference received,including interference that may
cause undesired operation.

FCC Warnings: Replacement or substitution of transistors, regular diodes or other parts
of a unique nature, with parts other than those recommended by Cobra may cause a
violation of the technical regulations of part 95 of the FCC rules, or violation of type
acceptance requirements of part 2 of the rules.

®

Radios

11 12

Warranty & Trademark Acknowledgment

Limited One-Year Warranty

Altis Global Limited warrants to the original consumer purchaser only that this product and
the component parts thereof, will be free from defects in workmanship and materials for a
period of one year from the date of rst consumer purchase. During this period, Altis will,
repair or replace, at its sole option and discretion, this product or any defective parts. Altis’
liability hereunder shall be limited to repair or replacement of the defective part or parts, and
such correction shall constitute a fulllment of all of Altis’ warranties hereunder.

This limited warranty is only valid for the original consumer purchaser in limited jurisdictions
and is not transferrable. This limited warranty will automatically terminate prior to expiration
if this product is sold or otherwise transferred to another party. The product must be
purchased from Altis or an authorized dealer or the warranty is void. This limited warranty is
valid only for products purchased and utilized in specic jurisdictions. Please visit our
website at www.cobrawalkietalkie.com for a list of jurisdictions wherein this limited
warranty is valid.

This limited warranty does not cover damage due to misuse, abuse, negligence, acts of God,
accident, commercial use or modication of, or to any part of this product. This warranty
does not cover damage due to improper operation, maintenance or installation; ordinary
wear and tear; or attempted alterations or repairs by anyone other than Altis or someone
authorized by Altis to do warranty work. Any unauthorized alterations or repairs will void this
warranty. This limited warranty does not cover product sold AS IS or WITH ALL FAULTS.
This limited warranty is invalid if the factory applied serial number or date stamp has been
altered, defaced or removed from this product. This limited warranty does not cover product
purchased or utilized in a jurisdiction not covered.

The procedure for obtaining service and support, and the applicability of this warranty, will
vary depending on the country or jurisdiction in which you purchase and utilize the product.
For details on obtaining product service, support and other warranty information please visit
www.cobrawalkietalkie.com.

This warranty gives you specic legal rights, and you may also have other rights which vary
from state to state and country to country.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, ALTIS MAKES NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALTIS EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
EXPRESSED WARRANTY.

LIMITATION OF REMEDIES AND DAMAGES. REPAIR OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ALTIS SHALL NOT BE
LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED
TO ATTORNEYS’ FEES AND/OR COSTS OF LITIGATION, FOR BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT. ALTIS IS NOT LIABLE FOR ANY DAMAGES CAUSED
BY THE PRODUCT OR BY THE PRODUCT TO PERFORM, INCLUDING ANY LOST PROFITS, LOST
SAVINGS, INCIDENTAL DAMAGES, OR CONSEQUENTIAL DAMAGES. ALTIS IS NOT LIABLE
FOR ANY CLAIM MADE BY A THIRD PARTY OR MADE BY YOU FOR A THIRD PARTY. THIS
LIMITATION APPLIES WHETHER DAMAGES ARE SOUGHT, OR A CLAIM MADE, UNDER THIS

13 14

WARRANTY OR AS A TORT CLAIM (INCLUDING NEGLIGENCE OR STRICT PRODUCT LIABILITY),
A CONTRACT CLAIM, OR ANY OTHER CLAIM. THIS LIMITATION CANNOT BE WAIVED OR
AMENDED BY ANY PERSON. THIS LIMITATION OF LIABILITY WILL BE EFFECTIVE EVEN IF
ALTIS OR AN AUTHORIZED REPRESENTATIVE OF ALTIS HAS BEEN ADVISED BY YOU OF THE
POSSIBILITY OF ANY SUCH DAMAGES.

Some states and countries do not allow limitations on how long an implied warranty lasts
and do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specic legal rights, and you
may also have other rights which vary from state to state and country to country.

Provided that the product was purchased from Altis itself or through its authorized reseller or
agent and utilized in the U.S.A., Altis will, without charge, repair or replace, at its option,
defective products, products or component parts upon delivery to the authorized Altis Global
Limited Authorized Service Center, accompanied by proof of the date of rst customer
purchase, such as a duplicated copy of a sales receipt.

You must pay any initial shipping charges required to ship the product for warranty service,
but the return charges, to an address in the U.S.A, will be at Altis’ expense, if the product is
under warranty.

For Products Purchased Outside the U.S.A.

Please contact your authorized local reseller or agent for warranty information.

Trademark Acknowledgment

Manufactured, distributed, or sold by Altis Global Limited, ofcial licensee for this product.

®

, microTalk®, Nothing Comes Close to a Cobra®, and the snake design are registered

Cobra
trademarks of Cobra Electronics Corporation, USA. Cobra Electronics Corporation™ is a
trademark of Cobra Electronics Corporation, USA. All other product or service names are the
property of their respective owners.

©Cobra Electronics Corporation, USA 2018. All rights reserved.