Cobra POWRFLO Instruction Manual
606-0102B
Page
1
of 2
* Cobra recommends you always wear a helmet while riding. Please never operate your motorcycle while unde
r
1 – INTAKE COVER W/ IN
TAKE SCREEN ASSEMBLY
3 – LOCK WASHER, 1/4” TOOTHED
HARLEY:
Read all instructions carefully and completely before installing your new POWRFLO
TM
Intake.
VELOCITY
SUPPLIED
GASKET
MOUNTING
FIGURE 1
(3) 1/4”
-
20 x 3/4”
(2) SUPPLIED
(2) SUPPLIED
BOLTS
(2) STOCK
BREATHER
HOSES
SUPPORT
(3) LOCK
BREATHER SLOTS
®
23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. 714.692.5016
www.cobrausa.com
Items Supplied >
Application(s) >
1 – K&N ® VENTURI AIR FILTER
1 – BILLET VELOCITY STACK
1 – MOUNTING PLATE
1 – SUPPORT BRACKET
1 – INTAKE GASKET
2 – O-RING, SILICONE
2 – BREATHER BOLT, 3/8”-16 X 1”
3 – BOLT, 1/4”-20 X 7/8”, BUTTONHEAD W/ LOCK PATCH
3 – BOLT, 1/4”-20 X 5/8”, HEX FLANGE
Instruction Manual >
1. Remove the allen bolt from the center of the stock air cleaner to remove the cover. Remove the (3)
bolts securing the formed bracket located on top of the air filter. Then remove and discard the air filter,
air box and seals/gaskets.
2. Remove and discard the (2) stock breather bolts and (2) stock o-rings from the cylinder heads; save
the breather hoses for reuse during installation.
3. Insert (3) supplied 1/4”-20 x 3/4” buttonhead bolts with lock washers through the mounting holes in
the velocity stack and mounting plate. While holding that assembly together with one hand, insert the
(2) breather hoses through the mounting plate and into the velocity stack with the hoses rotated
outward, as shown in Figure 1. Make sure the hoses are bottomed out in the back of the velocity
stack.
4. Join together the assembly from Step 3 with the supplied support bracket and gasket then start
threading the (3) buttonhead bolts into the throttle body, but do not tighten.
SOFTAIL 2000-10
ROCKER 2008-10
DYNA 2000-10
WASHERS
BUTTONHEAD
BOLTS W/
LOCK PATCH
STACK
PLATE
BREATHER
BRACKET
VELOCITY STACK BACKSIDE
INTAKE
O-RINGS
ORIENT TO TOP
WHEN ASSEMBLED
the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.
DOCUMENT NO. 0017 REV. A
05/10
1 ®
606-0102B
DOCUMENT NO
. 0018 REV. B
IMPORTANT
:
ASSEMBLY FROM
K&N® VENTURI
x
”
INTAKE
FIGURE
2
To clean your black air intake system use a liquid
based soap detergent, such as
CLEANING
®
23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. 714.692.5016
www.cobrausa.com
Instruction Manual >
5. Place a supplied o-ring onto both supplied breather bolts. Insert the breather bolts through the
support bracket openings and into the cylinder heads and lightly snug. Now snug the (3) buttonhead
bolts evenly, and then fully tighten them to the throttle body. Tighten the (2) breather bolts.
6. Insert outer end of rubber hoses over nipples on breather bolts.
7. Place the supplied K&N® filter onto the velocity stack. Insert the intake screen assembly into the
POWRFLOTM intake cover so the holes in the bent tabs align with the threaded bosses.
8. Place the intake cover over the air filter and align threaded bosses with the mounting plate holes.
Insert the (3) supplied 1/4"-20 x 5/8” hex flange bolts through the mounting plate, intake screen and
into the intake cover then tighten. See Figure 2.
AIR FILTER
Page 2 of 2
INTAKE COVER
(3) 1/4”-20
HEX FLANGE
BOLTS
STEPS 3-6
SCREEN
To achieve optimum performance from your new POWRFLOTM Air Intake it is suggested
that you install a Cobra Fi2000® Digital Fuel Processor. Visit www.fi2000r.com
5/8
INSTRUCTIONS:
dishwashing soap applied with a soft cloth and rinse with clean water. Note: Avoid
abrasive cleaning methods such as granular or dry cleansers, simple green, Scotch -Brite
or steel wool pads. Abrasives may breach the coating and shorten life.
05/10
2 ®
Loading...