Order Form...................................................................................................51
If You Think You Need Service...................................Back Cover
Features of This Product
• UHF FM Frequencies
• 10 Weather Channels
• Weather Alert
• No License Required
• No Air Time Fees
• Up to 2 mile range
• 14 Main Channels
• 38 CTCSS Subchannels
• LCD Function Display
• Pri va te Call® Vo i ce
S c ra m b l i n g
• Talk Confirmation To n e
• Ca l l / Ring Bu t to n
• Recharging Pads
• Retractable Antenna
• Au to Ba t te ry Saver Ci rc u i ty
• Auto Squelch
• 10 Memory Locations
• Memory Scan
• Channel or CTCSS Scan
• Lock Key
• Ri n g / Vi b ra te No t i f i ca t i o n
• Belt Holster
• Water Resistant
• Dual Watch
1
Page 2
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 2
Operation
Battery
Installation
Note
Batteries not included with
microTalk 2-way radio.
Install Batteries
Clear antenna.
Pull lock tab down
and lift door up
(towards you) to
remove battery
cover.
Insert four “AAA”
batteries.Position
batteries according
to po l a ri ty marki n g s.
Operation
Note
Always use high quality
alkaline or NiMH batteries.
Incorrect positioning can
damage both the batteries
and the unit.
Only the Cobra NiMH
battery (Part # FA-BP)
pack can be recharged.
See Accessories on page 50.
Charge ports for recharging
NiMH (Nickel Metal
Hydride) battery pack are
located on back of unit.
Note
When batteries are low or
need charging the ()
BATT LOW indicator will
blink.Replace alkaline
batteries or recharge NiMH
battery pack.
2
3
Page 3
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 4
Operation
Turning On
Your microTalk
Note
Wh e n ever the unit is on yo u
can re ce i ve co m m u n i ca t i o n s.
Illuminating
the Display
Turning On Your microTalk
Press and hold thePower Bu t ton fo r
two seco n d s.An audible “to n e”will indicate
the unit is on,and the LCD will go on.
Illuminating the Display
Press and releaseLIGHT/MAX RANGE
Button to illuminate display for ten seconds.
Auto Battery Power Saver
Your microTalk has a unique circuit designed to
extend battery life. If there are no transmissions
within 10 seconds,the unit will automatically
switch to battery savemode.
Theicon will flash.
Operation
Auto Battery
Power Saver
Note
The Auto Battery Save
Circuit does not effect the
unit’s ability to receive
incoming transmissions.
4
5
Page 4
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 6
Operation
Select Main
Channel
Note
Units must be on same
channel and subchannels
to communicate.
Note
Channels 8-12 generally are
less used and give better
results for communications
in most areas.
Note
Push and holdChannel up
or down Buttons for fast
channel advance.
Select Main Channel (1-14)
Turn on microTalk.An audible “tone”will indicate the unit is on and then the LCD will go
through a 3 second self-test and then go to
Operational Mode.
Select channel by moving the Channel Button
up or down.
Select CTCSS Subchannel (00-38)
The CTCSS (Continuous Tone Controlled Squelch
System) is a great convenience when you are in
an area with many radios.It acts like a gate to
transmissions from other radios.Once your radio
is set to a CTCSS code,you will only hear transmissions from other radios on the same channel
and the same CTCSS code.
Tu rn on the micro Ta l k .An audible “to n e”w i l l
i n d i cate the unit is on and then the LCD will go
t h rough a 3 second self-test and then go to
O pe rational Mod e.
Operation
Select CTCSS
Subchannel
Note
CTCSS (Coded Tone
Controlled Squelch System)
is an advanced subcoding
system that allows
segmentation of a
main channel.
Note
If you push and hold the
Mode Button,the LCD display will cycle through the
different functions.
Note
To return to operational
mode and not save your
last setting push and
release Talk Button.
Select main channel by moving the Channel
Button up or down.
continued
6
7
Page 5
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 8
Operation
Select CTCSS
Subchannel
Note
Press and hold Channel Button
up or down for fast channel
advance.
Select CTCSS Subchannel continued
Press and releaseMode Button.Small num-
bers flash next to channel display on LCD.
Se l e cts u bchannel number by moving the
Channel Bu t ton up or dow n.
Battery Low
When in use the () icon may begin flashing.
This is a warning to you that your batteries are
getting low.
Replace alkaline batteries as soon as possible or
recharge NiMH battery pack.
Operation
Battery Low
Note
When batte ry ca p a c i ty is at
the 1/4 level it is re co mmended that you re p l a ce
a l kaline batte ries or
re c h a rge your NiMH (Nicke l
Metal Hyd ride) batte ry pack.
Only the Cobra NiMH
battery (Part # FA-BP)
pack can be recharged.
Note
NiMH rechargeable battery
Pack (item #FA-BP) and
desktop charger (item #FACR) are not included with
this unit. See Accessories
section on page 50.
When desired subchannel is displayed p ress and
re l e a s eLock Bu t to n .If key audible tone is
o n ,an audible tone will co n f i rm your select i o n .
8
9
Page 6
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 10
Operation
Talking to
Another
Party
Note
While Talk Button is
depressed you cannot
receive incoming calls.
Note
When you release the
Talk Button,the person you
are talking to will hear a
tone indicating that it’s ok
to talk.See Talk
Confirmation Tone section
on page 13.
Pressand holdTalk Button.
Th e()i con will appe a r.
Hold mic about 2 inches from mouth.
Speak in a normal voice.
Talk Confirmation Tone
Your listener will hear an audible
tone when you release
theTalk Button.
This alerts the other party t h at
you are finished talking and it’s
OK for them to begin talki n g.
When finished talking:
Operation
Talk
Confirmation
Tone
Standby Mode
ReleaseTalk Button and listen for response.
10
ReleaseTalk Button to receive incoming
transmissions.
Your microTalk is always in the standby mode
when the Talk Button is not pressed and you are
not in function mode. See Advanced Features
section on page 18.
Note
While Talk Bu t ton is depre s s e d
you cannot re ce i ve inco m i n g
co m m u n i ca t i o n s.
11
Page 7
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 12
Operation
Calling
Another
Party
Calling Another Party
To alert another party that you wish to
communicate:
Turn on your microTALK 2-way radio.
An audible “tone”will indicate the unit is on.
The LCD will go through a 3 second self test
and then to operational mode.
Placeantenna in full upright position.
Select desired channel by moving Channel
Button up or down.Both the calling and
receiving units must be on same channel and
subchannel for the call function to work.
Operation
Note
Your incoming “Ca l l ”a u d i o
ringing level is dependent on
your unit’s volume setting.
12
Press and releaseCall Button.The ( ) indicator icon will flash and the ( ) icon
will remain on for 3 seconds.
The unit you are calling will hear a 2 second
ring tone.
Your microTalk is always in the standby mode
when theTalk Button is not depressed.
13
Page 8
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 14
Operation
Auto Squelch
Maximum
Range
Extender
Note
To learn more about the
range of your microTALK,
see page 42.
Range is dependent on
battery condition and
geographic territory.
Auto Monitor
Auto Squelch
Your microTALK is equipped with Auto Squelch,
which automatically shuts off weak transmissions
and unwanted noise due to terrain conditions or
if you have reached your range limit.
Maximum Range Extender
Au to squelch can be te m po ra rily re m oved to allow
all signals to enter (Maximum Range Exte n d e r ) .
Press and holdLIGHT/MAX RANGE
Button to allow all signals to enter.
Auto Monitor
When the signal you want to hear is consistently
weak,you may place the radio in Maximum
Range mode without having to constantly hold
the button.Press and hold the Maximum Range
Extender Button for five seconds.You will hear an
audible beep confirmation.To return to normal
operation,momentarily press the Maximum
Range Extender Button again or change channels.
Listening to Weather Channels
Turn on your microTalk 2 -way radio.An audible
“tone”will indicate the unit is on. The LCD will
go through a 3 second self test and then go
operational mode.
Placeantenna in full
upright position.
Press and release Mode Button until weather
iconflashes.The last weather channel
tuned will be displayed.
Operation
Listening to
Weather
Channels
14
15
Page 9
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 16
Operation
Listening to
Weather
Channels
Weather Alert
Turning
Weather Alert
On/Off
Listening to Weather Channels
Pre s s Channel Bu t ton up or down to select
the appro p ri ate channels for your are a .Th e re
a re ten we ather channels to choose fro m ,( 0 - 9 )
To exit weather reception,press the Mode or
Talk Button.The radio will go to the last FRS
channel and CTCSS sub-channel.
Weather Alert
A tone alert will be automatically activated
when NOAA activates emergency weather notification.
To turnWeather Alert on/off:
PressMode until Weather Alert
Icon flashes
Pressing Channel Button up or down will
turnWeather Alert On or Off.
Once you’ve selected On or Off, press
Lock Button to confirm.
.
E x t e rnal Microphone/Speaker Jack
External Microphone/Speaker Jack
Your microTalk 2-Way Radio can be fitted with a
variety of accessories,(not included) freeing your
hands for other tasks.
To attach an external microphone/speaker
accessory:
Open Mic/Spkr tab on top of unit.
Insert plug into the Mic/Spkr jacks.
External
Microphone/
Speaker Jack
Note
External microphone/
speaker (item #FA-SM) is
not included with this unit.
See Accessories Section on
page 50.
16
17
Page 10
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 18
Advanced Features
Advanced
Features
No te
When using or prog ra m m i n g
f u n ct i o n s,pushing and
releasing the Mode Bu t ton or
the Lock Bu t ton will save all
e n te red info r m a t i o n .
No te
To exit out of function mod e
and return to ope ra t i o n a l
m ode without saving ente re d
i n formation simply press the
Lock Bu t to n .
Advanced Features
Your microTalk has many advanced features
not found on other 2-way radios.
These include:
• 10 Memory Storage Location and Recall
• Memory Scan
• Channel/Sub Channel Scan
• Private Call® (Voice Scramble)
• Dual Watch
• Ring/Vibrate Notification Modes
• Tone Indicator Settings
Key StrokeTone
Talk Confirmation Tone
• Lock Key
• Dual Watch
Advanced Features
Programming Memory Locations
Your microTalk has 10 memory (0-9) locations for
storing your most frequently used channels.
Turn on microTalk.An audible “tone”will
indicate the unit is on and then the LCD will
go through a 3 second self-test and then go to
Operational Mode.
Press and releaseMode Button until ()
icon and a memory location flashes.
Programming
Memory
Locations
18
Select memory location you wish to change
by pressing Channel Button up or down.
continued
19
Page 11
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 20
Advanced Features
Programming Memory Locations continued
Note
Once you enter memory
mode you can talk and listen to any channel you
select after programming is
complete. See Using
Memory Locations section
on page 23.
Press and releaseMode Button again.
Main Channel and () Icon will flash.
Select desired main channel you wish to store
(1-14) by pressing Channel Button up or
down.
Advanced Features
Press Channel Button up or down to set the
main channel in memory and moves to subchannel selection. The subchannel begins
flashing.The () icon will remain flashing.
Select desired subchannel you wish to store
(00-38) by pushing Channel Button up or
down.
Programming
Memory
Locations
Note
Press and hold Channel
Button up or down for fast
channel advance.
Note
You can push and hold the
Talk Bu t ton to begin talki n g
a n y t i m e.
20
21
Page 12
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 22
Advanced Features
Programming
Memory
Locations
Note
If you push and hold the
Mode Button,the LCD display will cycle through the
different functions.
Programming Memory Locations continued
After selecting your Memory Channel and
Main/Sub Channels,for immediate entry
pressTalk Button.
or...
After selecting you Memory Channel and
Main/Sub Channel,DONOT press any buttons
for 10 seconds and your unit will automatically
set the Memory and Main/Sub Channels.It will
then go to the NEW channel.
Press and releaseLock Button to return to
Operational Mode original Main Channel.
or...
Press and releaseMode Button to proceed
to next Function Mode (Scan).
Advanced Features
Memory Channel Recall/Talk
To recall a channel in memory:
Press and releaseMode Button until ()
icon and a memory location flashes.
Using Memory
Locations
22
Select desired memory location you wish to
recall (0-9) by pushing Channel Button up
or down.
continued
23
Page 13
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 24
Advanced Features
Using Memory
Locations
Note
If Mode Button is pushed
while listening/talking,
programming will begin.
See Programming Memory
Locations on page 22.
Using Memory Locations continued
Press and holdTalk Button and talk.Your
radio will stay on this recalled location until
you exit out of memory function mode.
Repeat step 2 for recalling other memory
locations.
To exit the Memory Mode and return to
Operational Mode:
Advanced Features
Scan Function
Turn on microTALK.An audible “tone”will
indicate the unit is on and then the LCD will
go through a 3 second self-test and then go
to Operational Mode.
Press and releaseMode Button until ()
icon and Main Channel flashes.
Scan Function
Note
The microTALK “zeros out”
the subchannels to allow
scanning of the main
channels.
Press and releaseMode Button.
24
continued
25
Page 14
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 26
Advanced Features
Scan Function
Scan Function continued
Press Channel Button up or down and the
unit will begin scanning the main channels.
Unit will co ntinue to scan all main channels and
s top if an incoming transmission is dete cte d.
Your microTALK will pick it up for 10 seconds.
Within 10 seconds you can:
Press and holdTalk Button and talk.Your
radio will return to operational mode on
that channel.
or...
Press Channel Button up or down to
rescan the main channel.
or...
Proceed to subchannel scan on next page.
Advanced Features
To scan subchannels:
Press and releaseMode Button and
subchannel and scan icon will flash.
Press and release Channel Button up or down
and subchannel scanning begins and stops
when an incoming transmission is detected.
26
continued
27
Page 15
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 28
Advanced Features
Your microTalk will pick it up for 10 seconds.
Within 10 seconds you can:
Press and holdTalk Bu t ton and talk.Your ra d i o
will re t u rn to ope rational mode on that channel.
or...
Note
If you wish to proceed to the
n ext function mod e,p u s h
and release Mode Bu t to n .
( Pri va te Call Vo i ce Scra m b l e ) .
Press Channel Button up or down to rescan
the main channel.
To exit the Scan Mode and return to
Operational Mode:
Press and releaseMode Button.
Advanced Features
Memory Scan Function
Me m o ry Scan co nve n i e ntly allows you to access freq u e ntly used channel and sub-channel co m b i n at i o n s.
Turn on your microTALK 2 -way radio.An audible “tone”will indicate the unit is on. The LCD
will go through a 3 second self test and then
go to operational mode.
Placeantenna in full
upright position.
Memory Scan
Function
28
Press and releaseMode Button until
MEM/SCAN icon flashes.
continued
29
Page 16
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 30
Advanced Features
Memory Scan
Function
Note
When you push and hold the
Talk Bu t to n ,the unit will ex i t
out to ope rational mod e.If
a fter 10 seconds no select i o n
is made,the unit will return to
o pe rational mod e.
Memory Scan Function continued
Press Channel Button up or down to begin
the scan mode.
The radio will stop at the first memory location for 1/2 second.
• If no signal is detected it will move on.
• If a signal is detected,it will stay at that location for 10 seconds. If you want to stay at
that location for more than 10 seconds,pressand releaseTalk Button.
Advanced Features
Private Call (Voice Scrambling)
Private Call ensures that no one can eavesdrop on
your conversation.
To engage the Private Call function:
Turn on microTalk.An audible “tone”will
indicate the unit is on and then the LCD will
go through a 3 second self-test and then go
to Operational Mode.
Press and releaseMode Button until
() icon flashes.
Private Call
(Voice
Scrambling)
To leave Memory Scan,press and release the
Mode or Talk Button at any time.
30
continued
31
Page 17
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 32
Advanced Features
Private Call
( Vo i c e
S c r a m b l i n g )
Note
When you push and hold
the Talk Bu t to n ,the unit ex i t s
out to ope rational mod e.
If,a fter 10 seconds no selection is made,the unit will
return to ope rational mod e.
Private Call (Voice Scrambling) continued
Press Channel Button up or down to turn private call ON or OFF.To confirm status press
Lock button.
Advanced Features
Ringer/Vibrate Modes
Your microTALKwill signal you that there is an
incoming transmission with either a tone or a
vibration or both.To set for Ringer/Vibrate:
Turn on microTALK.An audible “tone”will
indicate the unit is on and then the LCD will go
through a 3 second self-test and then go to
Operational Mode.
Press and releaseMode Button until
icon flashes.
Ringer/Vibrate
Modes
32
Press Channel Button up and down until
icon appears for Ringer Only Mode.
continued
33
Page 18
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 34
Advanced Features
Ringer/Vibrate
Modes
No te
When you push and hold
the Talk Bu t to n ,the unit ex i t s
out to ope rational mod e.
If,a fter 10 seconds no selection is made,the unit will
return to ope rational mod e.
Ringer/Vibrate Modes continued
Press and release Channel Button up and down
again.icon appears for Vibrator Only Mode.
Press and release Channel Buttonup and
d own again and bo t hi cons will be displaye d
for Ringer and Vi b rate Mod e.
Advanced Features
After selecting the mode you desire push and
releaseLock Button orMode Button
to proceed to next function.
Ringer/VibrateTest
To test the ringer/vibrate mode:
Turn on unit.
Press and holdLock Button and Call
Button simultaneously.Unit will ring,vibrate,
or ring/vibrate for 4 seconds.
Note
Unit must be in operational
mode to test ring/vibrate.
34
35
Page 19
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 36
Advanced Features
Tone Settings
Tone Setting
PressMode Button until flashing
Press Channel Button up or down to turn
On or Off.
To set option:
PressLock Button.This will immediately
enter new setting;
PressMode Button.This will enter new setting and go to new Function Mode;
Wait 10 seconds.It will go to Operational
Mode with new setting.
Advanced Features
Talk Confirmation Tone Indicator
To te m po ra rily eliminate the Talk Co n f i rm ation To n e :
PressMode Button until flashing
Press Channel Button up or down to turn
On or Off .
To set option:
PressLock Button.This will immediately
enter new setting;
PressMode Button.This will enter new setting and go to new Function Mode;
Wait 10 seconds.It will go to Operational
Mode with new setting.
36
37
Page 20
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 38
Advanced Features
Lock Function
Note
Call Button,Range Extender
Button and Talk Button
do not lock and are fully
operational while the unit
is locked.
The unit cannot lock while
in Function Mode.
Lock Function
The purpose of the LOCK function is to lock most
buttons to avoid accidental operation.
To engage the LOCK function:
Press and hold for one seco n dLock Bu t to n .
will hear an audible co n f i rm at i o n .Most butto n s
a re loc ke d.
To“unlock”press and releasebutton again.
If the Beep Fu n ction is ONyou will hear an audible co n f i rm at i o n .Most buttons are loc ke d.
Buttons are“unlocked”andicon disappears.
i con flashes. If the Beep Fu n ction is ONyo u
Dual Watch Function
Dual Watch allows you to simultaneously monitor any two pre s e l e cte d
Family Radio Se rv i ce channels.
Select first channel and CTCSS
code which you desire to Dual
Watch. (please see pages 6
and 7).
Dual Watch Function
Advanced Features
Dual Watch
Function
Dual Watch
Function
38
Press and releaseMode Bu t ton unt i l
i con flashes.
Pre s s Channel Bu t ton up and down to
s e l e ct second channel.
continued
39
Page 21
FRS315WX MANUAL.qx 12/5/00 11:17 AM Page 40
Advanced Features
Dual Watch
Function
PressMode Bu t ton to set CTC S S .
C TCSS channel numbers will flash.
Pre s s Channel Bu t ton up and down
to select CTC S S .
Advanced Features
Dual Watch Function
To enter Dual Watch when the second channel
and CTCSS are already stored,pressthe
Mode Button untilicon flashes.
Pre s sLockBu t to n .Dual watch will be g i n .
Dual Watch
Function
PressLock Button.This will store the second channel and CTCSS and start Dual Watch.
To terminate Dual Watch and go to Normal
Mode,press Lock or Talk Buttons.
40
Pre s s Talk Bu t ton to exit Dual Watch Mod e.
41
Page 22
FRS315WX MANUAL.qx 12/5/00 11:18 AM Page 42
microTalk Range
microTalk
Range
microTALK Range
Your micro TA L K Radio has a range of up to2 miles.
This effective range can be shortened under
some conditions.
Under flat,o pen co n d itions you will ex pe rie n ce the micro TA L K’s
maximum ra n g e.
Range can be re d u ce d
by buildings and fo l i a g e
in the path of the signal.
Range will be furt h e r
re d u ced by dense
foliage and hilly te rra i n .
To achieve maximum
range the auto squelch
can be ove r ri d d e n .
Re fer to Maximum
Range Extender sect i o n
on page 14.
Making Life Easier and Safer
microTALK2-Way Radio Can Make Life
Easier and Safer
As you become familiar with your microTALK
Radio you will find many of your own uses for
the unit.Some suggestions include:
Talking with
fellow hikers.
Communicating
be tween basement and
f i r s t,s e cond or third
f l oo r.
Keeping track of the kids
in a shopping mall.
Ta l king to a neighbor
or a fri e n d.
microTalk
2-Way Radios
Can Make
Life Easier
and Safer
continued
42
43
Page 23
FRS315WX MANUAL.qx 12/5/00 11:18 AM Page 44
Making Life Easier and Safer
microTalk
2-Way Radios
Can Make
Life Easier
and Safer
HolsterBelt Clip and
Desk Stand
microTALK 2-Way Radio Can Make Life
Easier and Safer
Checking on traveling
companions in
another car.
Holster/Belt Clip/Desk Stand
Your microTALK Radio comes with a custom molded plastic holster.Its unique dual-function design
enables it to act as a handy desktop storage unit,
as well as easily attaching to your belt for maximum convenience and portability.
Desk StandBelt Clip
Agree on a meeting
spot after an event.
Frequency Range
The microTalk unit represents one of the most
advanced FM two-way radios available.
The microTALK 2-Way Radio will give you years
of service if cared for properly.
Here are some suggestions:
Handle unit gently.Keep away from dust.
Caring for Yo u r
m i c ro TA L K
R a d i o
Note
Modifying or tampering
with the radio’s internal
components can cause
malfunction and will
invalidate the warranty.
If your radio is not performing as it should,please call
Cobra at 773.889.3087.Do
not return the unit to the
retailer.
46
Never place the
unit in water or in
a moist place.
Avoid ex po s u re
to ext reme
te m pe rat u re s.
47
Page 25
FRS315WX MANUAL.qx 12/5/00 11:18 AM Page 48
microTalkSpecifications
I.GENERAL SPECIFICATIONS
A.GENERAL
CH=14 CHANNELS WITHIN 462-467 MHZ
B.RECEIVER
1. SENSITIVITY
FOR 12 DB SINAD uV 0.25
FOR CALL SIG.DETECTION uV 0.2
2. MAX.AUDIO OUTPUT @10% THD MW100
3. MAX.S/N RATIO @ 1mV RF INPUT DB 45
4. SQUELCH
a) SENS.uV 0.2
b) ATTACK TIME mS 120
c) CLOSING TIME mS 200
5. AUDIO FREQUENCY RESP.
@ 300 HZ DB -6
@ 3000 HZ DB -6
8. TRANSIENT FREQ.BEHAVIOR
a)TX ONmS 30
b) TX OFF mS 5
D.POWER SUPPLY
1.BATTERY LIFE (1:1:18 RATIO) HR 24
2.BATTERY (4 x AAA)V4.8 - 6.0
UNIT
UNIT
Limited Two Year Warranty
COBRA ELECTRONICS CORPORATION warrants that its
COBRA FRS Radios,and the component parts thereof,will
be free of defects in workmanship and materials for a
period of two (2) years from the date of first consumer purchase.This warranty may be enforced by the first consumer
purchaser,provided that the product is utilized within
the U.S.A.
COBRA will,without charge,repair or replace,at its option,
defective FRS radios,products or component parts upon
delivery to the COBRA factory Service Department,accompanied by proof of the date of first consumer purchase,
such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship
the product for warranty service,but the return charges
will be at Cobra's expense, if the product is repaired or
replaced under warranty.
Exclusions: This limited warranty does not apply;1) to any
product damaged by accident;2) in the event of misuse or
abuse of the product or as a result of unauthorized alterations or repairs;3) if the serial number has been altered,
defaced or removed;4) if the owner of the product resides
outside the U.S.A.
All implied wa rra nt i e s,including wa rra nties of
m e rc h a nt a b i l i ty and fitness for a particular purpose
a re limited in duration to the length of this wa rra nty.
CO B RA shall not be liable for any incident a l ,co n s e q u e ntial or other damages;i n c l u d i n g,without limitat i o n ,d a mages resulting from loss of use or cost of installat i o n .
Some states do not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages,so the above limitations may not apply to you.
Cobra Electronics
Corporation
6500 West Cortland Street
Chicago,Illinois 60707
48
49
Page 26
FRS315WX MANUAL.qx 12/5/00 11:18 AM Page 50
Optional Accessories
NiMH Rechargeable
Battery Pack
High performance
Rechargeable Nickel Metal
Hydride battery pack
FA-BP $29.95
Ear Bud Mi c ro p h o n e
Mi n i a t u re microphone and earbud for pri va te liste n i n g.
M A-EBM $29.95
2 Po rt De s k top Ch a rg e r
Ch a rges your micro T alk Radio
and (1) NiMH batte ry pack
FA- C R$ 2 9 . 9 5
Lapel Speaker/ Microphone
Remote speaker/microphone
combination.
M A- S M$ 2 4 . 9 5
You Can Find These Fine Accessories AtYour Local
Cobra Dealer
If you wish,you can order directly from Cobra.
Order by phone
Call 1.773.889.3087
(Press 1 from the main menu) 8 a.m.-6 p.m. M-F CST.
Order by mail or fax
Please fill out order form on next page,and mail/fax
directly
to Cobra.
FA-BPNiMH Rechargeable Battery Pack$29.95
M A - E B MEar Bud Microphone$ 2 9 . 9 5
M A - V O XVox Headset/Mic$ 4 9 . 9 5
FA-CR2 Port Desktop Charger$29.95
MA-SMLapel Speaker/Microphone $24.95
FA-HR3Replacement Belt Clip$4.95
For credit card orders fill out order
form and fax to: 1.773.622.2269
or call 1.773.889.3087
(Press 1 from the main menu)
8:00 am - 6:00 pm, M-F, CST.
Please print clearly
Name
Address (No P.O.Box)
CityState
Zip
Telephone ( )
Credit Card No.Exp.Date
Customer Signature
Circle One: Visa MasterCard Discover
Allow 4 to 6 weeks for delivery.Offer valid in Continental U.S.only.
Subtotal
(Tax if applicable)
Shipping/handling
Total
Make check or money order (no stamps)
payable to:
Cobra Electronics
Accessories Dept.
6500 West Cortland St. Chicago, IL 60707
Shipping & Handling
Amount ofShipping/
OrderHandling
$25.00 and under $4.75
$25.01–$40.00$6.95
$40.01–$80.00$9.25
$80.01–$120.00 $10.25
$120.01–$160.00 $11.75
$160.01 and up$14.50
For AK,HI and PR please add
an additional $15.00 for UPS
shipments.
50
51
Page 27
FRS315WX MANUAL.qx 12/5/00 11:18 AM Page 52
The Co b ra line of quality prod u cts
also includes:
• Ci t i zens Band Ra d i o s
• Mi c ro Ta lk™Radios
Family Radio Se rv i ce
• High Ge a r™Ac ce s s o ri e s
• Radar De te cto r s
• Sa fe ty Al e rt
™
Traffic Wa rning Sys te m s
Notes
Nothing comes close to a Co b ra
™
Page 28
FRS315WX MANUAL.qx 12/5/00 11:18 AM Page 54
Cobra Electronics Corporation
6500 West Cortland Street
Chicago, IL 60707
If You Think You Need Service
For te c h n i cal assistance,please call our Au to m a ted Help Desk which can assist
you by answering the most fre q u e n t ly asked questions about Co b ra prod u ct s.
(773) 889-3087
24 hours a day,7 days a week.
A Consumer Service Representative can be reached through this same number
8:00 am - 6:00 pm,Monday through Friday,CST.
Technical assistance is also available on-line in the Frequently Asked Questions (FAQ)
section at www.cobraelectronics.com or by e-mail to productinfo@cobraelectronics.com
If you think you need service call 1.773.889.3087
“If your product should require factory service please call Cobra first before sending your unit in.
This will ensure the fastest turn-around time on your repair.”
You may be asked to send your unit to the Cobra factory.It will be necessary to furnish the following in order to have the product serviced and returned.
1. For Warranty Repair include some form of proof-of-purchase, such as a mechanical reproduction
or carbon or a sales receipt. If you send the original receipt it cannot be returned.
2. Send the entire product.
3. Enclose a description of what is happening with the unit.Include a typed or clearly print name
and address of where the unit is to be returned.
4. Pack unit securely to prevent damage in transit. If possible,use the original packing material.
5. Ship prepaid and insured by way of a traceable carrier such as United Parcel Service (UPS) or First
Class Mail to avoid loss in transit to: Cobra Factory Service,Cobra Electronics Corporation,6500
W.Cortland St.,Chicago,IL 60707.
6. If the unit is in warranty,upon receipt of your unit it will either be repaired or exchanged
depending on the model. Please allow approximately 3 to 4 weeks before contacting us for
status.If the unit is out of warranty a letter will automatically be sent informing you of the
repair charge or replacement charge.If you have any questions,please call 1.773.889.3087
for assistance.
“Ingenious Prod u cts for Easier Co m m u n i cat i o n .”
Page 29
FRS315WX MANUAL.qx 12/5/00 11:31 AM Page 56
The Family Radio Service Story
The Family Radio Service Story
Ever wish you could talk to someone who wasn’t
within earshot? Like contacting ski partners back
at the lodge? Or letting a friend know how to find
you in a busy mall? Cobra’s microTalk radio is a
great way for friends or family to increase their
fun–and safe ty – by staying in touch while on the go.
The FCC (Federal Communications Commission)
has created 14 license free frequency bands,
or channels,called Family Radio Service (FRS)
frequencies. All of these 14 channels are easily
accessed on your Cobra FRS radio. These channels are in the UHF (Ultra High Frequency) band
which means great penetration through buildings,thick forests,hills,and other dense structures.
They are also FM (Frequency Modulation) signals
which means crystal clear reception even in
crowded noisy environments.
FCCWarnings
Replacement or substitution of transistors,regular
1.
diodes or other parts of a unique nature,with
parts other than those recommended by Cobra,
may cause a violation of the technical regulations
of part 95 of the FCC Rules,or violation of Type
Acceptance requirements of Part 2 of the Rules.
Included with your microTalk
1. Holster/Belt Clip/Desk Stand
A1
Page 30
FRS315WX MANUAL.qx 12/5/00 11:31 AM Page 57
Controls and Indicators
1. Antenna
2. Microphone/Speaker Jack
3. On/Off Power Button
4. LCD Display Panel
5. Light/Max Range Button
6. Down/Up Volume Control
7. Speaker
8 . Battery Compartment
9. Talk Button
10. Call Button
11. Channel Select Button
12. Battery Charge Pads
13. Mode Key
14. Key Lock
1 1
1 3
1
9
1 0
Our Thanks to You
Thank you for purchasing this Cobra microTalk
2-way Radio. Properly used,this Cobra product
will give you many years of reliable service.
1
8
2
1 2
2
3
9
1 1
4
1 0
5
1 4
1 3
6
Customer Support
Should you encounter any problems with the
product or not understand its many features,
please refer to this owner’s manual. If,after
referring to the manual,you still need help,
call Cobra Customer Service at 773.889.3087.
Cobra Customer Service
Live operators are available
M-F 8:00 am - 8:00 pm CST
at: 773.889.3087
Automated Technical
Assistance available
24 hours a day,seven days
a week.E-mail questions to:
productinfo@
cobraelectronics.com
Co b ra on the Wo rld Wide We b :
Fre q u e n t ly As ked Qu e s t i o n s
( FAQ) can be found on-line at:
www.cobraelectronics.com
A2
7
This device complies with part 15 of
the FCC rules.Operation is subject to
the condition that this device does not
cause harmful interference.
A3
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.