Rev.
DCA No.
Date
Description of Change
806-005 / 807-005 Audio Selector Panel
SM806 Installation and Operation Manual Supplement
Part #: 806-005, 807-005 Description: Audio Selector Panel
Document #: SM806-005-810-0 Rev: 1.00
Prepared By: Geoff Melton Checked By: Ken Marshall Approved By: Robert Davis
Revisions
1.00 W14250 Oct 30, 2014 Initial release
SM806 Supplement Rev: 1.00 Oct 15, 2014 Page i
ENG-FORM: 810-0105.DOT
CONFIDENTIAL AND PROPRIETARY TO COBHAM
INSTALLATION AND OPERATION
MANUAL SUPPLEMENT
Part #: 806-005, 807-005 Description: Audio Selector Panel
Document #: SM806-005-810-0 Rev: 1.00
This supplement contains installation and operation information that is unique to the
806-005 and 807-005. Installation and operation information common to the 806-000
and 807-000 base units can be found in the Installation and Operation section of the
SM806 Installation and Service Manual.
Note: This supplement replaces and obsoletes all previous supplements for the
806-005 and 807-005 Audio Selector Panels.
1 Description
This supplement describes the differences between the 806-000 / 807-000 base units,
and the 806-005 / 807-005 derivatives. All changes apply to both the 806-005 / 807-005
variants unless otherwise indicated.
afpmi^v
m
c
a
kloj
^eop
N O
kloj
^a`
N O
kloj
`ar
N O
kloj
j
c
a
ujfq
O
N
fkme
q p
N `ljj O
ec
jf`
m^
bjbo
l
kloj
^rql
`ljj
u
v
Row 1
jf`
bjbo
kloj
^rql
`ljj
Row 2
^q`
N
O
ec
pibt
J H
ad
cobb
p
q
_
v
jho
_`k
N k^s O
N ajb O
N ^ac O
jho
pmho
pmho
Row 3
slf`b
fabkq
^rafl
^iqk
_
l
q
e
Row 4
slf`b
fabkq
ec
Row 5
kloj
ec=pbi`^i
ef
mobpp
ec=pbi`^i
Row 6
ilkloj
qbpq
806-005 807-005
Figure 1 – 806-005 and 807-005 Faceplates
l
u
v
_
l
q
e
ujfq
O
N
N `ljj O
N k^s O
N
N ^ac O
jho
_`k
ec
m^
O
ajb
pibt
J H
ad
cobb
kloj
q
p
SM806 Supplement Rev: 1.00 Oct 15, 2014 Page 1 of 3
CONFIDENTIAL AND PROPRIETARY TO COBHAM
806-005 / 807-005 Audio Selector Panel
SM806 Installation and Operation Manual Supplement
1.1 Functional/Cosmetic Changes
The 806-005 and 807-005 are identical to the 806-000 and 807-000 with the following
exceptions:
a) The 806-005 and 807-005 have HF SELCAL indicator/switch added to row 6 and
the associated circuitry is added onto the HF SELCAL indicator/switch.
2 Installation
For general Installation information and drawings, see Service Manual SM806 Section
2. Select the appropriate revision of the drawing for the serial number of the unit under
consideration. The drawings specific to this derivative are listed below, and can be
found at the end of this supplement.
2.1 Installation Drawings
DRAWING REV. DESCRIPTION TYPE SERIAL #
806-005
806-005-403-0 1.00 Audio Selector Panel Interconnect All
806-005-405-0 1.00 Audio Selector Panel Connector Map All
806-005-922-0 1.10 Audio Selector Panel Mech. Installation All
DRAWING REV. DESCRIPTION TYPE SERIAL #
807-005
807-005-403-0 1.00 Audio Selector Panel Interconnect All
807-005-405-0 1.00 Audio Selector Panel Connector Map All
807-005-922-0 1.10 Audio Selector Panel Mech. Installation All
3 Operation
For general Operation information, see Service Manual SM806 Section 3 with the
following exceptions:
SM806 Supplement Rev: 1.00 Oct 15, 2014 Page 2 of 3
CONFIDENTIAL AND PROPRIETARY TO COBHAM
806-005 / 807-005 Audio Selector Panel
SM806 Installation and Operation Manual Supplement
3.1 SELCAL indicator/switch
ec=pbi`^i
mobpp
qbpq
806-005 807-005
ec=pbi`^i
End of Installation and Operation Manual Supplement
The HF SELCAL indicator (row 6) indicates when a call
from the aircraft’s Selective Calling System is being
received. On 806-005, a switch also allows the operator
to apply a test signal to the SELCAL system.
SM806 Supplement Rev: 1.00 Oct 15, 2014 Page 3 of 3
CONFIDENTIAL AND PROPRIETARY TO COBHAM
Mating connectors
Unit Connector Unit Connector
Part No.
P1 (61-pin)
Amphenol
TVP02RW-25-61P
Shielded wire must be used for all audio connections. AWG 20-22 size should be used for the input supply power and
power ground; panel lighting supplyand return; knob lighting supply and return; and chassis ground. AWG 22-24 size
wire should be used for all other connections.
P1-A OXY MIC HI P1-i TEST MODE JUMPER IN
P1-B OXY MIC LO P1-j TEST MODE JUMPER OUT
P1-C OXYMIC MODE INTERCONNECT P1-k SPKR OUTPUT HI
P1-D NORM/OXY MIC TIP PTT P1-m SPKR OUTPUT LO
P1-E NORMAL MIC HI P1-n CHASSIS GND
P1-F NORMAL MIC LO P1-p +28 VDC
P1-G INPH MIC HI OUT P1-q POWER GROUND
P1-H INPH LISTEN P1-r SELCAL TEST SWITCH OUT
P1-J HAND MIC HI P1-s COMM1 MIC HI (1)
P1-K HAND MIC LO P1-t COMM1 KEY (1)
P1-L INPH SWITCH P1-u COMM5 KEY (N/C)
P1-M VOX THLD P1-v COMM2 KEY (2)
P1-N SPKR INPUT HI P1-w AW BYPASS OUT
P1-P SPKR INPUT LO P1-x N/C
P1-R MUXDATA LO P1-y PA VOL
P1-S MUX DATA HI P1-z AW BYPASS IN
P1-T CHASSIS GND P1-AA PA KEY
P1-U COMM3 MIC HI (HF) P1-BB PTT KEY SWITCH
P1-V COMM3 KEY (HF) P1-CC LIGHT NEUTRAL
P1-W N/C P1-DD LIGHT POSITIVE
P1-X N/C P1-EE CHASSIS GND
P1-Y COMM4 MIC HI (N/C) P1-FF COMM4 KEY (N/C)
P1-Z HAND MIC PTT P1-GG COMM5 MIC HI (N/C)
P1-a COMM2 MIC HI (2) P1-HH AUDIO COMMON
P1-b NORM SWITCH OUT P1-JJ MIC AUDIO COMMON
P1-c N/C P1-KK AUDIO ALTN SWITCH
P1-d N/C P1-LL CHASSIS GND
P1-e N/C P1-MM CHASSIS GND
P1-f SELCAL INDICATOR DIM P1-NN AUDIO COMMON
P1-g SELCAL INDICATOR IN P1-PP PA MIC HI
P1-h INPH MIC LO OUT
Mating Connector
Part No.
Amphenol
D38999-26WJ61SN
CONFIDENTIALAND PROPRIETARY TO COBHAM
DRAWN
AP 11-30-10
TITLE
FILE
806-005405-0.DOC
CHECK APPROVED
PINOUTLIST
CAGE CODE
1B7G3
PART NO.
FOR MODEL 806-005
DRAWING NO.
806-005405-0
DWG. TYPE
PINOUT LIST
SHEET
1 / 3
SIZE
A
REV.
1.00
Mating connectors
Unit Connector Unit Connector
Part No.
P2 (61-pin)
Amphenol
TVP02RW-25-61PC
Shielded wire must be used for all audio connections. AWG 20-22 size should be used for the input supply power and
power ground; panel lighting supply and return; knob lighting supply and return; and chassis ground. AWG 22-24 size
wire should be used for all other connections.
P2-A EMER 28V IN P2-i MFD 1
P2-B EMER 28V IN P2-j AFD CMN 1
P2-C DG FREE P2-k AFD CMN 2
P2-D N/C P2-m N/C
P2-E EMER SWITCH OUT P2-n N/C
P2-F N/C P2-p PFD 3
P2-G
P2-H
P2-J
P2-K
P2-L
P2-M
P2-N
P2-P
P2-R
P2-S
P2-T CDU 26 P2-AA AHRS 2
P2-U TDR CNM 2 P2-BB AHRS CMN
P2-V CDU 1 P2-CC CDU 11
P2-W CDU 2 P2-DD CDU 13
P2-X
P2-Y
P2-Z
P2-a COMMON 22 P2-HH N/C
P2-b SLEW + P2-JJ
P2-c SLEW - P2-KK
P2-d TDR 12 P2-LL
P2-e TDR 9 P2-MM
P2-f TDR 3 P2-NN
P2-g TDR 6 P2-PP
P2-h PFD 1
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
N/C
P2-q PFD 2
P2-r MFD 2
P2-s MKR HI 3
P2-t MKR HI 2
P2-u MKR HI 1
P2-v MKR SNS CMN
P2-w AHRS 1
P2-x ADC 1
P2-y ADC CMN
P2-z ADC 2
P2-EE CDU 24
P2-FF N/C
P2-GG
N/C
N/C
N/C
N/C
N/C
N/C
N/C
Mating Connector
Part No.
Amphenol
D38999-26WJ61SC
CONFIDENTIALAND PROPRIETARY TO COBHAM
DRAWN
AP 11-30-10
TITLE
PINOUTLIST
FILE
806-005405-0.DOC
CAGE CODE
1B7G3
PART NO.
FOR MODEL 806-005
DRAWING NO.
806-005405-0
DWG. TYPE
PINOUT LIST
SHEET
2 / 3
SIZE
A
REV.
1.00
806-005 Front Panel / 700-XXX Pin Association Table
This table describes which 700-XXX pin each 806-005 front panel control affects.
MODEL 806-005 FRONT PANEL CONTROL MODEL 700-XXXPIN
P1-12 COMM-1 HI
COMM 1
P1-11 COMM-1 SDTN HI
P1-34 COMM-1/COMM-1SDTN LO
P1-13 COMM-2 HI
COMM 2
P1-17 COMM-2 SDTN HI
P1-35 COMM-2/COMM-2SDTN LO
P1-8 COMM-3 HI
COMM 3 (HF)
P1-19 COMM-3 SDTN HI
P1-31 COMM-3/COMM-3SDTN LO
P1-7 COMM-4 HI
COMM 4 (NOT INSTALLED)
P1-18 COMM-4 SDTN HI
P1-30 COMM-4/COMM-4SDTN LO
P1-4 COMM-5 HI
COMM 5 (NOT INSTALLED)
P1-16 COMM-5 SDTN HI
P1-27 COMM-5/COMM-5SDTN LO
NAV 1 P1-42 HI/P1-38 LO NAV-1
NAV 2 P1-21 HI/P1-40 LO NAV-2
1
1
DME 1 P1-15 HI/P1-57 LO DME-1
DME 2 P1-14 HI/P1-36 LO DME-2
ADF 1 P1-62 HI/P1-39 LO ADF-1
ADF 2 P1-41 HI/P1-37 LO ADF 2
1
1
MKR BCN P1-10 HI/P1-33 LO MKR-1
MKR 2 (NOT INSTALLED) P1-9 HI/P1-32 LO MKR-2
INPH P1-44/P1-45 INPH HI
2
SPARE 1 (NOT INSTALLED) P1-6 HI/P1-29 LO SPARE-1
SPARE 2 (NOT INSTALLED) P1-5 HI/P1-28 LO SPARE-2
AUDIO ALTN SWITCH P1-3 EMERGENCY SWITCH
SPKR P1-53 HI/P1-51 LO SPKR
XMIT (PA) P1-20 PA SDTN HI
VOL P1-2 HI/P1-25 LO HDPH
(T) VOX THRESHOLD TRIMMER P1-46 INPH SQUELCH (VOX THRESHOLD)
1. VOICE/BOTH/IDENT SWITCH CONTROLS VOICE OR TONE FILTERING FOR NAV1, NAV2, ADF1 AND ADF2 INPUTS OF MODEL 700.
2. HAND MIC PTT AND PTT SWITCH INPUTS TO 806-XXX CAUSE INPH AUDIO OF MODEL 700 TO BECOME MUTED FOR ALL
POSITIONS OF XMIT ROTARY SWITCH WHEN TRANSMITTING, EXCEPT PA. P1-44 IS ELECTRICALLY COMMON WITH P1-45
WITHIN THE MODEL 700. THERE IS NO AUDIO LO FOR INPH HI SINCE THE SIGNAL REFERENCE IS THE MODEL 700 POWER
GROUND.
3. HAND MIC PTT AND PTT SWITCH INPUTS TO 806-XXX CAUSE PA SIDETONE TO BECOME ACTIVE IF TRANSMITTING TO PA USING
XMIT ROTARY SWITCH PA POSITION.
4. OXY/NORM SWITCH WILL ACTIVATE SPKR WHEN SET TO OXY POSITION.
5. AUTO COMM SWITCH WILL CAUSE THE RECEIVER VOLUME CHANNEL THAT IS SELECTED BY THE XMIT ROTARY SWITCH TO
BECOME ACTIVE.
6. SIDETONE TRIMMER ON THE 806 FRONT PANEL CONTROLS THE MODEL 700 MASTER SIDETONE VOLUME.
6
6
6
6
6
3
REFERTO MODEL 700 PINOUT FOR ALL OTHER CONNECTIONSOF MODEL 700-[ ]
CONFIDENTIALAND PROPRIETARY TO COBHAM
DRAWN
AP 11-30-10
TITLE
PINOUTLIST
FILE
806-005405-0.DOC
CAGE CODE
1B7G3
PART NO.
FOR MODEL 806-005
DRAWING NO.
806-005405-0
DWG. TYPE
PINOUT LIST
SHEET
3 / 3
SIZE
A
REV.
1.00
Mating connectors
Unit Connector Unit Connector
Part No.
P1 (61-pin)
Amphenol
TVP02RW-25-61P
Shielded wire must be used for all audio connections. AWG 20-22 size should be used for the input supply power and
power ground; panel lighting supply and return; knob lighting supply and return; and chassis ground. AWG 22-24 size
wire should be used for all other connections.
P1-A OXY MIC HI P1-i TEST MODE JUMPER IN
P1-B OXY MIC LO P1-j TEST MODE JUMPER OUT
P1-C OXYMIC MODE INTERCONNECT P1-k SPKR OUTPUT HI
P1-D NORM/OXY MIC TIP PTT P1-m SPKR OUTPUT LO
P1-E NORMAL MIC HI P1-n CHASSIS GND
P1-F NORMAL MIC LO P1-p +28 VDC
P1-G INPH MIC HI OUT P1-q POWER GROUND
P1-H INPH LISTEN P1-r N/C
P1-J HAND MIC HI P1-s COMM1 MIC HI (1)
P1-K HAND MIC LO P1-t COMM1 KEY (1)
P1-L INPH SWITCH P1-u COMM5 KEY (N/C)
P1-M VOX THLD P1-v COMM2 KEY (2)
P1-N SPKR INPUT HI P1-w AW BYPASS OUT
P1-P SPKR INPUT LO P1-x DG FREE
P1-R MUXDATA LO P1-y PA VOL
P1-S MUX DATA HI P1-z AW BYPASS IN
P1-T CHASSIS GND P1-AA PA KEY
P1-U COMM3 MIC HI (HF) P1-BB PTT KEY SWITCH
P1-V COMM3 KEY (HF) P1-CC LIGHT NEUTRAL
P1-W COMMON 22 P1-DD LIGHT POSITIVE
P1-X N/C P1-EE CHASSIS GND
P1-Y COMM4 MIC HI (N/C) P1-FF COMM4 KEY (N/C)
P1-Z HAND MIC PTT P1-GG COMM5 MIC HI (N/C)
P1-a COMM2 MIC HI (2) P1-HH AUDIO COMMON
P1-b NORM SWITCH OUT P1-JJ MIC AUDIO COMMON
P1-c EMER SWITCH IN P1-KK AUDIO ALTN SWITCH (N/C)
P1-d SLEW (+) P1-LL CHASSIS GND
P1-e SLEW (-) P1-MM CHASSIS GND
P1-f SELCAL INDICATOR DIM P1-NN AUDIO COMMON
P1-g SELCAL INDICATOR IN P1-PP PA MIC HI
P1-h INPH MIC LO OUT
Mating Connector
Part No.
Amphenol
D38999-26WJ61SN
CONFIDENTIALAND PROPRIETARY TO COBHAM
DRAWN
AP 11-30-10
TITLE
FILE
807-005405-0.DOC
CHECK APPROVED
PINOUTLIST
CAGE CODE
1B7G3
PART NO.
FOR MODEL 807-005
DRAWING NO.
807-005405-0
DWG. TYPE
PINOUT LIST
SHEET
1 / 2
SIZE
A
REV.
1.00
807-005 Front Panel / 700-XXX Pin Association Table
This table describes which 700-XXX pin each 807-005 front panel control affects.
MODEL 807-005 FRONT PANEL CONTROL MODEL 700-XXXPIN
P1-12 COMM-1 HI
COMM 1
P1-11 COMM-1 SDTN HI
P1-34 COMM-1/COMM-1SDTN LO
P1-13 COMM-2 HI
COMM 2
P1-17 COMM-2 SDTN HI
P1-35 COMM-2/COMM-2SDTN LO
P1-8 COMM-3 HI
COMM 3 (HF)
P1-19 COMM-3 SDTN HI
P1-31 COMM-3/COMM-3SDTN LO
P1-7 COMM-4 HI
COMM 4 (NOT INSTALLED)
P1-18 COMM-4 SDTN HI
P1-30 COMM-4/COMM-4SDTN LO
P1-4 COMM-5 HI
COMM 5 (NOT INSTALLED)
P1-16 COMM-5 SDTN HI
P1-27 COMM-5/COMM-5SDTN LO
NAV 1 P1-42 HI/P1-38 LO NAV-1
NAV 2 P1-21 HI/P1-40 LO NAV-2
1
1
DME 1 P1-15 HI/P1-57 LO DME-1
DME 2 P1-14 HI/P1-36 LO DME-2
ADF 1 P1-62 HI/P1-39 LO ADF-1
ADF 2 P1-41 HI/P1-37 LO ADF 2
1
1
MKR BCN P1-10 HI/P1-33 LO MKR-1
MKR 2 (NOT INSTALLED) P1-9 HI/P1-32 LO MKR-2
INPH P1-44/P1-45 INPH HI
2
SPARE 1 (NOT INSTALLED) P1-6 HI/P1-29 LO SPARE-1
SPARE 2 (NOT INSTALLED) P1-5 HI/P1-28 LO SPARE-2
AUDIO ALTN SWITCH (NOT INSTALLED) P1-3 EMERGENCY SWITCH
SPKR P1-53 HI/P1-51 LO SPKR
XMIT (PA) P1-20 PA SDTN HI
VOL P1-2 HI/P1-25 LO HDPH
(T) VOX THRESHOLD TRIMMER P1-46 INPH SQUELCH (VOX THRESHOLD)
1. VOICE/BOTH/IDENT SWITCH CONTROLS VOICE OR TONE FILTERING FOR NAV1, NAV2, ADF1 AND ADF2 INPUTS OF MODEL 700.
2. HAND MIC PTT AND PTT SWITCH INPUTS TO 807-XXX CAUSE INPH AUDIO OF MODEL 700 TO BECOME MUTED FOR ALL
POSITIONS OF XMIT ROTARY SWITCH WHEN TRANSMITTING, EXCEPT PA. P1-44 IS ELECTRICALLY COMMON WITH P1-45
WITHIN THE MODEL 700. THERE IS NO AUDIO LO FOR INPH HI SINCE THE SIGNAL REFERENCE IS THE MODEL 700 POWER
GROUND.
3. HAND MIC PTT AND PTT SWITCH INPUTS TO 807-XXX CAUSE PA SIDETONE TO BECOME ACTIVE IF TRANSMITTING TO PA USING
XMIT ROTARY SWITCH PA POSITION.
4. OXY/NORM SWITCH WILL ACTIVATE SPKR WHEN SET TO OXY POSITION.
5. AUTO COMM SWITCH WILL CAUSE THE RECEIVER VOLUME CHANNEL THAT IS SELECTED BY THE XMIT ROTARY SWITCH TO
BECOME ACTIVE.
6. SIDETONE TRIMMER ON THE 807 FRONT PANEL CONTROLS THE MODEL 700 MASTER SIDETONE VOLUME.
6
6
6
6
6
3
REFERTO MODEL 700 PINOUT FOR ALL OTHER CONNECTIONSOF MODEL 700-[ ]
CONFIDENTIALAND PROPRIETARY TO COBHAM
DRAWN
AP 11-30-10
TITLE
PINOUTLIST
FILE
807-005405-0.DOC
CAGE CODE
1B7G3
PART NO.
FOR MODEL 807-005
DRAWING NO.
807-005405-0
DWG. TYPE
PINOUT LIST
SHEET
2 / 2
SIZE
A
REV.
1.00
Loading...