Cobalt Networks OPEN GEAR 9002 User Manual

9002

HD/SD SDI

Distribution Amplifier

Cobalt Digital Inc.

9002-OM Version: 1.0

Owner’s Manual

9002 •••• HD/SD SDI Reclocking Distribution Amplifier Owner’s Manual

• Cobalt Part Number: 9002-OM

• Document Version: 1.0

• Printed in the United States.

• Last Author: KGM

• Printing Date: 08/19/08 9:02 AM

The information contained in this Owner’s Manual is subject to change without notice or obligation.

Cobalt Digital Inc. Reproduction or reverse engineering of copyrighted software is prohibited.

Notice

The material in this manual is furnished for informational use only. It is subject to change without notice and should not be construed as a commitment by Cobalt Digital Inc. Cobalt Digital Inc assumes no responsibility or liability for errors or inaccuracies that may appear in this manual.

Trademarks

• is a registered trademark of Ross Video Limited.

•

• All other product names and any registered and unregistered trademarks mentioned in this

manual are used for identification purposes only and remain the exclusive property of their respective owners.

is a registered trademark of Cobalt Digital Inc.

Page 2 of 18 9002 Owner’s Manual •••• (V 1.0)

Important Regulatory and Safety Notices

Before using this product and any associated equipment, refer to the “Important Safety Instructions” listed below so as to avoid personnel injury and to prevent product damage.

Products may require specific equipment, and /or installation procedures be carried out to satisfy certain regulatory compliance requirements. Notices have been included in this publication to call attention to these specific requirements.

Symbol Meanings

Warning

Caution

Notice

ESD

Susceptibility

This symbol on the equipment refers you to important operating and maintenance (servicing) instructions within the Product Manual Documentation. Failure to heed this information may present a major risk of damage or injury to persons or equipment.

The symbol with the word “Warning” within the equipment manual indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury.

The symbol with the word “Caution” within the equipment manual indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

The symbol with the word “Notice” within the equipment manual indicates a situation, which if not avoided, may result in major or minor equipment damage or a situation which could place the equipment in a non-compliant operating state.

This symbol is used to alert the user that an electrical or electronic device or assembly is susceptible to damage from an ESD event.

Important Safety Instructions

Caution

Warning

This product is intended to be a component product of the openGear to the openGear the proper installation and safe operation of the frame as well as it’s component products.

Certain parts of this equipment namely the power supply area still present a safety hazard, with the power switch in the OFF position. To avoid electrical shock, disconnect all A/C power cords from the chassis' rear appliance connectors before servicing this area.

frame Owner’s Manual for important safety instructions regarding

frame. Refer

Warning

9002 Owner’s Manual •••• (V 1.0) Page 3 of 18

Service barriers within this product are intended to protect the operator and service personnel from hazardous voltages. For continued safety, replace all barriers after any servicing.

This product contains safety critical parts, which if incorrectly replaced may present a risk of fire or electrical shock. Components contained within the product’s power supplies and power supply area, are not intended to be customer serviced and should be returned to the factory for repair.

To reduce the risk of fire, replacement fuses must be the same type and rating. Only use attachments/accessories specified by the manufacturer.

Environmental Information

The equipment that you purchased required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment.

To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources, Cobalt Digital encourages you to use the appropriate take-back systems. These systems will reuse or recycle most of the materials from your end-of-life equipment in an environmentally friendly and health consc i ous manner.

The crossed-out wheeled bin symbol invites you to use these systems.

If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration.

You can also contact Cobalt Digital for more information on the environmental performances of our products.

Page 4 of 18 9002 Owner’s Manual •••• (V 1.0)

Contents

Introduction 6

In This Chapter...........................................................................................................................6

A Word of Thanks......................................................................................................................6

Overview....................................................................................................................................6

Functional Block Diagram.........................................................................................................7

Supported Serial Rates...............................................................................................................8

Documentation Terms................................................................................................................8

Installation and Setup 9

In This Chapter...........................................................................................................................9

Static Discharge .........................................................................................................................9

Unpacking...................................................................................................................... ............9

Rear Module Installation (Optional)........................................................................................10

Board Installation.....................................................................................................................11

Cable Connections....................................................................................................................11

Card Control and Status...........................................................................................................12

Card Status.................................................................................................................12

Switches.....................................................................................................................12

Remote Control 13

In This Chapter.........................................................................................................................13

DashBoard Control System Software.......................................................................................13

Service Information 15

In This Chapter.........................................................................................................................15

Troubleshooting Checklist.......................................................................................................15

Warranty and Repair Policy.....................................................................................................16

Ordering Information 17

9002 and Related Products.......................................................................................................17

Contact Cobalt Digital Inc........................................................................................................18

Visit us at the Cobalt Digital Inc. website................................................................................ 18

9002 Owner’s Manual •••• (V 1.0) Page 5 of 18

Introduction

In This Chapter

This chapter includes the following sections:

• A Word of Thanks

• Overview

• Functional Block Diagram

• Supported Audio and Video Formats

• Documentation Terms

A Word of Thanks

Overview

Congratulatio ns on choosing the openGearTM 9002 HD/SD Distribution Amplifier. The 9002 is part of a full line of modular conversion gear for broadcast TV environments. The Cobalt Digital openGear line includes video decoders and encoders, audio embeders and de-embeders, distribution amplifiers, format converters, and much more. Cobalt openGear conversion and distribution needs now and well into the future.

Should you have questions pertaining to the installation or operation of your 9002, please contact us at the numbers listed on the back cover of this manual. We are happy to help with any questions regarding this or any other openGear

The 9002 is a high quality HD/SD Distribution Amplifier. It is capable of equalizing and reclocking an SDI signal in HD or SD.

The 9002 can equalize an incoming SDI signal using up to 300m of cable at 270 Mbps and up to 120m of cable at 1.485 Gbps.

card.

modular conversion gear will meet your signal

Page 6 of 18 9002 Owner’s Manual •••• (V 1.0)

+ 12 hidden pages