Cobalt Networks 9006 User Manual

Page 1
9006
Triple 3G/HD/SD SDI
Distribution Amplifier
Cobalt Digital Inc.
9006-OM Version: 1.0
Owner’s Manual
Page 2
9006 ••• Triple 3G/HD/SD SDI Distribution Amplifier Owner’s Manual
Cobalt Part Number: 9006-OM
Document Version: 1.0
Printed in the United States.
Last Author: MWB
Printing Date: 08/19/08 8:38 AM
The information contained in this Owner’s Manual is subject to change without notice or obligation.
Copyright
© 2008 Cobalt Digital Inc. All rights reserved. Contents of this publication may not be reproduced in any form without the written permission of
Cobalt Digital Inc. Reproduction or reverse engineering of copyrighted software is prohibited.
Notice
The material in this manual is furnished for informational use only. It is subject to change without notice and should not be construed as a commitment by Cobalt Digital Inc. Cobalt Digital Inc assumes no responsibility or liability for errors or inaccuracies that may appear in this manual.
Trademarks
is a registered trademark of Ross Video Limited.
All other product names and any registered and unregistered trademarks mentioned in this
manual are used for identification purposes only and remain the exclusive property of their respective owners.
is a registered trademark of Cobalt Digital Inc.
Page 2 of 18 9006 Owner’s Manual ••• (V 1.0)
Page 3
Important Regulatory and Safety Notices
Before using this product and any associated equipment, refer to the “Important Safety Instructions” listed below so as to avoid personnel injury and to prevent product damage.
Products may require specific equipment, and /or installation procedures be carried out to satisfy certain regulatory compliance requirements. Notices have been included in this publication to call attention to these specific requirements.
Symbol Meanings
Warning
Caution
Notice
ESD
Susceptibility
This symbol on the equipment refers you to important operating and maintenance (servicing) instructions within the Product Manual Documentation. Failure to heed this information may present a major risk of damage or injury to persons or equipment.
The symbol with the word “Warning” within the equipment manual indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury.
The symbol with the word “Caution” within the equipment manual indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.
The symbol with the word “Notice” within the equipment manual indicates a situation, which if not avoided, may result in major or minor equipment damage or a situation which could place the equipment in a non-compliant operating state.
This symbol is used to alert the user that an electrical or electronic device or assembly is susceptible to damage from an ESD event.
Important Safety Instructions
Caution
Warning
This product is intended to be a component product of the openGear to the openGear the proper installation and safe operation of the frame as well as it’s component products.
Certain parts of this equipment namely the power supply area still present a safety hazard, with the power switch in the OFF position. To avoid electrical shock, disconnect all A/C power cords from the chassis' rear appliance connectors before servicing this area.
TM
TM
frame Owner’s Manual for important safety instructions regarding
frame. Refer
Warning
9006 Owner’s Manual ••• (V 1.0) Page 3 of 18
Service barriers within this product are intended to protect the operator and service personnel from hazardous voltages. For continued safety, replace all barriers after any servicing.
This product contains safety critical parts, which if incorrectly replaced may present a risk of fire or electrical shock. Components contained within the product’s power supplies and power supply area, are not intended to be customer serviced and should be returned to the factory for repair.
To reduce the risk of fire, replacement fuses must be the same type and rating. Only use attachments/accessories specified by the manufacturer.
Page 4
Environmental Information
The equipment that you purchased required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment.
To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources, Cobalt Digital encourages you to use the appropriate take-back systems. These systems will reuse or recycle most of the materials from your end-of-life equipment in an environmentally friendly and health consc i ous manner.
The crossed-out wheeled bin symbol invites you to use these systems.
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration.
You can also contact Cobalt Digital for more information on the environmental performances of our products.
Page 4 of 18 9006 Owner’s Manual ••• (V 1.0)
Page 5
Contents
Introduction 6
In This Chapter...........................................................................................................................6
A Word of Thanks......................................................................................................................6
Overview....................................................................................................................................6
Functional Block Diagram.........................................................................................................7
Supported Serial Rates...............................................................................................................8
Documentation Terms................................................................................................................8
Installation and Setup 9
In This Chapter...........................................................................................................................9
Static Discharge .........................................................................................................................9
Unpacking...................................................................................................................... ............9
Rear Module Installation (Optional)........................................................................................10
Board Installation.....................................................................................................................11
Cable Connections....................................................................................................................11
Card Control and Status...........................................................................................................12
Card Status.................................................................................................................12
Switches.....................................................................................................................12
Remote Control 13
In This Chapter.........................................................................................................................13
DashBoard Control System Software.......................................................................................13
Service Information 15
In This Chapter.........................................................................................................................15
Troubleshooting Checklist.......................................................................................................15
Warranty and Repair Policy.....................................................................................................16
Ordering Information 17
9006 and Related Products.......................................................................................................17
Contact Us 18
Contact Cobalt Digital Inc........................................................................................................18
Visit us at the Cobalt Digital Inc. website................................................................................ 18
9006 Owner’s Manual ••• (V 1.0) Page 5 of 18
Page 6
Introduction
In This Chapter
This chapter includes the following sections:
A Word of Thanks
Overview
Functional Block Diagram
Supported Audio and Video Formats
Documentation Terms
A Word of Thanks
Overview
Congratulatio ns on choosing the openGearTM 9006 Triple 3G/HD/SD Distribution Amplifier. The 9006 is part of a full line of modular conversion gear for broadcast TV environments. The Cobalt Digital openGear distribution amplifiers, format converters, and much more. Cobalt openGear gear will meet your signal conversion and distribution needs now and well into the future.
Should you have questions pertaining to the installation or operation of your 9006, please contact us at the numbers listed on the back cover of this manual. We are happy to help with any questions regarding this or any other openGear
The 9006 is a high quality three channel 3G/HD/SD Distribution Amplifier. It is capable of equalizing and equalizing three channels in 3G, HD or SD.
The 9006 can equalize incoming SDI signals using up to 300m of cable at 270 Mbps, up to 120m of cable at 1.485 Gbps, and up to 80m at 2.97Gbps.
One channel of ASI can be equalized and output for each of the SDI inputs. The BNC’s that output a non-inverted signal suitable for ASI are BNCs #4, 5, and 8.
TM
line includes video decoders and encoders, audio embedders and de-embedders,
TM
card.
TM
modular conversion
Page 6 of 18 9006 Owner’s Manual ••• (V 1.0)
Page 7
Functional Block Diagram
SDI OUT A
SDI IN 1
SDI IN 2
SDI IN 3
EQ
EQ
EQ
9006 Block Diagram
DA
DA
DA
DA
SDI OUT A
SDI OUT B
SDI OUT B
SDI OUT C
SDI OUT C
SDI OUT C
9006 Owner’s Manual ••• (V 1.0) Page 7 of 18
Page 8
Supported Serial Rates
The 9006 will reclock 270 Mbps, 1.485 Gbps, and 3 Gbps signals. Signals of other rates will be equalized and distributed to the outputs, and the reclocker will be bypassed.
Documentation Terms
The following terms are used throughout this guide:
Frame” refers to the 8310 frame that houses the 9006 card.
Operator” and “User” both refer to the person who uses the 9006.
Board” and “Card” all refer to the 9006 card itself, including all components and
switches.
System” and “Video system” refers to the mix of interconnected production and
terminal equipment in which the 9006 operates.
Page 8 of 18 9006 Owner’s Manual ••• (V 1.0)
Page 9
Installation and Setup
In This Chapter
This chapter includes the following sections:
Static Discharge
Unpacking
Rear Module Installation (Optional)
Board Installation
BNC Connections
Menu Structure
Factory Defaults
Static Discharge
Whenever handling the card and other related equipment, please observe all static discharge precautions as described in the following note:
Static discharge can cause serious damage to sensitive semiconductor devices. Avoid handling circuit boards in high static environments such as carpeted areas, and when wearing
ESD
Susceptibility
synthetic fiber clothing. Always exercise pr oper ground ing precautions when working on circuit boards and related equipment.
Unpacking
Unpack each card you received from the shipping container, and check the contents against the packing list to ensure that all items are included. If any items are missing or damaged, contact your sales representative or Cobalt Digital directly.
9006 Owner’s Manual ••• (V 1.0) Page 9 of 18
Page 10
Rear Module Installation (Optional)
If you are installing the card in a 8310-C-BNC or 8310-BNC frame (one with a 100 BNC rear module installed across the entire back plane), skip this section.
If you are installing the card into a slot with no rear module, you should have ordered and received a RM-9006-A Rear Module with your card. You will need to install it in your 8310 frame before you can connect cables.
Use the following steps to install the RM-9006-A in an 8310 openGear
1. Refer to the openGear
properly installed according to instructions.
2. On the rear of the 8310, locate the card frame slot.
3. As shown in Figure 2, seat the bottom of the RM-9006-A in the seating slot at the
base of the frame’s back plane.
TM
8310 frame Owner’s Manual, to ensure that the frame is
TM
frame:
Figure 2. Rear Module Installation
4. Align the top hole of the RM-9006-A with the screw hole on the top edge of the 8310
back plane.
5. Using a Phillips driver and the supplied screw, fasten the RM-9006-A panel to the
8310 back plane. Do not over tighten.
This completes the procedure for installing the RM-9006-A in an 8310 openGear
Page 10 of 18 9006 Owner’s Manual ••• (V 1.0)
TM
frame.
Page 11
Board Installation
Use the following steps to install the card in the openGearTM 8310 frame:
1. Refer to the Owner’s Manual of the openGear
is properly installed according to instructions.
TM
8310 frame to ensure that the frame
Heat and power distribution requirements within a frame may dictate specific slot placement of cards. Cards with many heat-producing components should be arranged to avoid areas of excess heat build-up,
Warning
particularly in frames using convecti on cooling.
2. After selecting the desired frame installation slot, hold the card by the edges and
carefully align the card edges with the slots in the frame. Then, fully insert the card into the frame until the rear connection plugs are properly seated on the midplane and rear modules.
This completes the procedure for installing the card in the openGear
Cable Connections
This section provides instructions for connecting cables to the installed BNC rear modules on the 8310 series frame backplane. Connect the input and output cables according to the following diagram. The input is internally ter minated with 75 Ohms. It is not necessary to terminate unused outputs.
HD/SD SDI Inp ut A
HD/SD SDI
Output A
HD/SD SDI
Output A
HD/SD SDI
Output C
HD/SD SDI
Input C
TM
8310 frame.
10
2
4
6
HD/SD SDI Inp ut B
HD/SD SDI Outpu t B
HD/SD SDI Outpu t B
8
HD/SD SDI Outpu t C
HD/SD SDI Outpu t C
1
3
5
7
9
Figure 3. BNC Designations for t he Card Rear M odule RM-9006-A or 8310-RM-100
9006 Owner’s Manual ••• (V 1.0) Page 11 of 18
Page 12
Card Control and Status
Card Status
The card has an LED that indicates whether Dashboard remote control is enabled, or if the switch bank controls the card. See description of switch 1 below.
The card also indicates the status of each of the outputs signal with the three banks of four LEDs labeled with the different supported formats (1080, 720, 625, 525). When the card has locked to a particular output format, that LED will be illuminated. When the card has not locked to a particular video format, the card will search all possible formats, and the lights will cycle rapidly.
Switches
1) The bank of eight switches (S1) on the front edge that controls the card are reserved for future use.
Page 12 of 18 9006 Owner’s Manual ••• (V 1.0)
Page 13
Remote Control
In This Chapter
This section provides a detailed explanation on using remote control functions with your card.
DashBoard Control System Software
The DashBoard Control System enables you to monitor and control openGearTM frames and controller cards from a computer. The DashBoard software and manual can be downloaded from the Cobalt Digital Inc. website.
Using the Menus
You must first install the DashBoard Control System software on your computer. Refer to the DashBoard User Manual for software installation procedures and for using the DashBoard interface.
9006 Owner’s Manual ••• (V 1.0) Page 13 of 18
Page 14
The Menu System
The following table and sections describe the menus, items, and parameters available from the DashBoard Control System software for the card.
Table 3. DashBoard Menus
Menu Item Parameters Description
Product CDI-9006 Manufacturer Cobalt Digital Inc.
############ Displays the Silicon Serial
Number of the card. Temperature of on card
sensor Current consumed from
+12V rail Measured vo ltage of +12V
rail
Card Info (Read-only)
Serial Number
Temperature
Input Current
Input Voltage
Lock Status
Lock Status A
Lock Status B
Lock Status C
Describes the current input rate
Describes the current input rate
Describes the current input rate
Page 14 of 18 9006 Owner’s Manual ••• (V 1.0)
Page 15
Service Information
In This Chapter
This chapter includes the following sections:
Troubleshooting Checklist
Warranty and Repair Policy
Troubleshooting Checklist
Routine maintenance to this openGearTM product is not required. In the event of problems with your card, the following basic troubleshooting checklist may help identify the source of the problem. If the module still does not appear to be working properly after checking all possible causes, please contact your openGear the “Contact Us” section at the end of this manual.
TM
products distributor, or the Technical Support department at the numbers listed under
1. Visual Review  Performing a quick visual check may reveal many problems, such
as connectors not properly seated or loose cables. Check the module, the frame, and any associated peripheral equipment for signs of trouble.
2. Power Check  Check the power indicator LED on the distribution frame front
panel for the presence of power. If the power LED is not illuminated, verify that the power cable is connected to a power source and that power is available at the power main. Confirm that the power supplies are fully seated in their slots. If the power LED is still not illuminated, replace the power supply with one that is verified to work.
3. Reseat the Card in the Frame Eject the card and reinsert it in the frame.
4. Check Control Settings  Refer to the Installation and Operation sections of the
manual and verify all user-adjustable component settings.
5. Input Signal Status  Verify that source equipment is operating correctly and that a
valid signal is being supplied.
6. Output Signal Path  Verify that destination equipment is operating correctly and
receiving a valid signal.
7. Module Exchange Exchanging a suspect module with a module that is known to
be working correctly is an efficient method for localizing problems to indivitriple modules.
9006 Owner’s Manual ••• (V 1.0) Page 15 of 18
Page 16
Warranty and Repair Policy
The openGearTM card is warranted to be free of any defect with respect to performance, quality, reliability, and workmanship for a period of FIVE (5) years from the date of shipment from our factory. In the event that your Cobalt Digital Inc. card proves to be defective in any way during this warranty period, Cobalt Digital Inc. reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics.
Should you find that this openGear repair your defective product should suitable replacement components be available. You, the owner, will bear any labor and/or part costs incurred in the repair or refurbishment of said equipment beyond the FIVE (5) year warranty period.
In no event shall Cobalt Digital Inc. be liable for direct, indirect, special, incidental, or consequential damages (including loss of profits) incurred by the use of this product. Implied warranties are expressly limited to the duration of this warranty.
This openGear operation of your Cobalt Digital Inc. Product. Cobalt Digital Inc. policy dictates that all repairs to the openGear
TM
card Owner’s Manual provides all pertinent information for the safe installation and
TM
card are to be conducted only by an authorized Cobalt Digital Inc. factory representative. Therefore, any unauthorized attempt to repair this product, by anyone other than an authorized Cobalt Digital Inc. factory representative, will automatically void the warranty. Please contact Cobalt Digital Inc. Technical Support for more information.
In Case of Problems
Should any problem arise with your openGearTM card, please contact the Cobalt Digital Inc. Technical Support Department. (Contact information is supplied at the end of this publication.)
TM
card has failed after your warranty period has expired, we will
A Return Material Authorization number (RMA) will be issued to you, as well as specific shipping instructions, should you wish our factory to repair your openGear
TM
card. If required, a temporary replacement module will be made available at a nominal charge. Any shipping costs incurred will be the responsibility of you, the customer. All products shipped to you from Cobalt Digital Inc. will be shipped collect.
The Cobalt Digital Inc. Technical Support Department will continue to provide advice on any product manufactured by Cobalt Digital Inc., beyond the warranty period without charge, for the life of the equipment.
Page 16 of 18 9006 Owner’s Manual ••• (V 1.0)
Page 17
Ordering Information
9006 and Related Products
Your 9006 Triple 3G/HD/SD SDI Distribution Amplifier is a part of the openGearTM family of products. Cobalt Digital offers a full line of openGear conversion, monitoring, synchronizers, encoders, decoders, embedders, and de-embedders, as well as analog audio and video products.
TM
terminal equipment including distribution,
Standard Equipment
9006 Triple 3G/HD/SD SDI Distribution Amplifier
9006-OM Triple 3G/HD/SD SDI Distribution Amplifier Owner’s Manual
Optional Equipment
9006-OM Triple 3G/HD/SD SDI Distribution Amplifier Owner’s Manual
(additional Owner’s Manual)
TM
RM-9006-A openGear
(10 BNC connector)
8310-C Digital Products Frame and Power Supply with Cooling Fans
(2RU, holds 10 cards)
8310-C-BNC Digital Products Frame and Power Supply with fixed 100-BNC Rear
Module and Cooling Fans. (2RU, holds 10 cards)
MFC-8310-N Network Controller Card (Additional)
Rear Module compatible with 9006
9006 Owner’s Manual ••• (V 1.0) Page 17 of 18
Page 18
Contact Us
Contact Cobalt Digital Inc.
PHONE
E-MAIL
POSTAL
SERVICE
General Business Office and Technical Support
Fax General Information
Sales Information
Cobalt Digital Inc.
217.344.1243
217.344.1245
Info@cobaltdigital.com Sales@cobaltdigital.com
2406 East University Avenue Urbana, IL 61802 USA
Visit us at the Cobalt Digital Inc. website.
http://www.cobaltdigital.com
Online catalog
Related products and full product lines
Trade show information
Dealer information
Cobalt Digital Inc. news
Page 18 of 18 9006 Owner’s Manual ••• (V 1.0)
Loading...