Cobalt Digital Inc 9433-EMDE-ADDA-EOOE, 9433-EMDE-ADDA-EO, 9433-EMDE-ADDA-OE Product Manual
9433-EMDE-ADDA9433-EMDE-ADDA
3G/HD/SD-SDI Fiber-Optic Converters with 16-Channel
AES / 8-Channel Analog Audio Embed / De-Embed
• 9433-EMDE-ADDA-EOOE — Fiber-Optic Transceiver
• 9433-EMDE-ADDA-EO — Fiber-Optic Transmitter
• 9433-EMDE-ADDA-OE — Fiber-Optic Receiver
Product Manual
Cobalt Digital Inc.
2506 Galen Drive
Champaign, IL 61821
Voice 217.344.1243 • Fax 217.344.1245
www.cobaltdigital.com
9433-EMDE-ADDA-OM (V1.4)
Copyright
©Copyright 2017, Cobalt Digital Inc. All Rights Reserved.
Duplication or distribution of this manual and any information contained within is strictly prohibited without the express written
permission of Coba lt Digital Inc. This manual and a ny information contained within, may not be re produced, distribute d, or
transmitted in any form, or by any means, for any purpose, without the express written permission of Cobalt Digital Inc.
Reproduction or reverse engineering of software used in this device is prohibited.
Disclaimer
The information in this document has been carefully examined and is believed to be entirely reliable. However, no responsibility
is assumed for inaccuracies. Furthermore, C obalt Digit al Inc. res erves the right to ma ke changes to any pro ducts herein to improve
readability, function, or design. Cobalt Digital Inc. does not assume any liability arising out of the application or use of any
product or circuit described herein.
Trademark Information
Cobalt® is a registered trademark of Cobalt Digital Inc.
openGear
Dolby
property of their respective owners.
®
is a registered trademark of Ross Video Limited. DashBoard™ is a trademark of Ross Video Limited.
®
is a registered trademark of Dolby Laboratories, Inc. Other product names or trademarks appearing in this manual are the
Congratulations on choosing the C obalt
Channel AES / 8-Channel Analog Audio Embed / De-Embed. The 9433-EMDE-ADDA is part of a full line of
modular processing and conversion gear for broadcast TV environments. The Cobalt Digital Inc. line includes
video decoders and encode rs, audio embedders and de-embedde rs, distribution amplifiers , format converters,
remote control systems and much more. Should you have questions pertaining to the installation or operation of
your 9433-EMDE-ADDA card, please contact us at the contact information on the front cover.
®
9433-EMDE-ADDA 3G/HD/SD-SDI Fiber-Optic Converter with 16-
Manual No.: 9433-EMDE-ADDA-OM
Document Version: V1.4
Release Date: May 1, 2017
Applicable for
Firmware Version
v1.0.8
(or greater):
Description of
product/manual
changes:
- UNBAL AES I/O port numbering shown in illustration for rear
module RM20-9433EMDE-C was incorrect. Illustration in this
manual version shows correct port numbering.
- Minor consistency updates to manual.
9433-EMDE-ADDA-OM (V1.4)
Table of Contents
Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Overview ................................................................................................................ 1-1
9433-EMDE-ADDA Card Software Versions and this Manual ............................ 1-2
Cobalt Reference Guides........................................................................................ 1-2
Manual Conventions............................................................................................... 1-3
Warnings, Cautions, and Notes .................................................................. 1-4
Labeling Symbol Definitions...................................................................... 1-4
Safety and Regulatory Summary............................................................................ 1-5
Warnings..................................................................................................... 1-5
Cautions...................................................................................................... 1-5
EMC Compliance Per Market .................................................................... 1-5
9433-EMDE-ADDA Functional Description......................................................... 1-6
9433-EMDE-ADDA Input/Output Formats............................................... 1-6
Audio Processor Description...................................................................... 1-8
User Control Interface ................................................................................ 1-8
9433-EMDE-ADDA Rear I/O Modules................................................... 1-10
Technical Specifications....................................................................................... 1-10
Warranty and Service Information ....................................................................... 1-13
Cobalt Digital Inc. Limited Warranty....................................................... 1-13
Contact Cobalt Digital Inc.................................................................................... 1-14
Chapter 2 Installation and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Overview ................................................................................................................ 2-1
Setting I/O Switches for Analog Audio (1-8) Ports ............................................... 2-1
Installing the 9433-EMDE-ADDA Into a Frame Slot............................................ 2-2
Installing a Rear I/O Module.................................................................................. 2-3
9433-EMDE-ADDA Rear I/O Modules..................................................... 2-5
Fiber and Balanced Audio Connections................................................................. 2-7
Setting Up 9433-EMDE-ADDA Network Remote Control................................... 2-8
9433-E MD E-A DDA -OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL i
Chapter 3 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Overview................................................................................................................. 3-1
Control and Display Descriptions........................................................................... 3-1
Function Menu/Parameter Overview.......................................................... 3-2
DashBoard™ User Interface ....................................................................... 3-3
Accessing the 9433-EMDE Card via Remote Control............................................ 3-4
Accessing the 9433-EMDE Card Using DashBoard™............................... 3-4
Checking 9433-EMDE Card Information............................................................... 3-6
9433-EMDE Function Menu List and Descriptions ............................................... 3-7
Input Video Controls .................................................................................. 3-8
Input Audio Status ...................................................................................... 3-8
Output Audio Routing ................................................................................ 3-9
Troubleshooting .................................................................................................... 3-13
Error and Failure Indicator Overview....................................................... 3-13
Basic Troubleshooting Checks.................................................................. 3-16
9433-EMDE Processing Error Troubleshooting....................................... 3-16
Troubleshooting Network/Remote Control Errors.................................... 3-17
In Case of Problems .................................................................................. 3-17
ii 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Overview
Chapter 1
Chapter 1 Introduction
Note: This manual is applicable for models:
• 9433-EMDE-ADDA-EOOE (Fiber Transceiver)
• 943 3-EM DE- A DDA-E O (Fiber Transmitter)
• 943 3-EMDE-ADDA-OE (Fiber Rece iv er)
All models function identically except for fiber I/O interface differences.
Differences between these models are noted where applicable. In all other
aspects, all versions function identically as described in this manual.
This manual provides installati on and o per at ing instr uct ions for the
9433-EMDE-ADDA 3G/HD/SD-SDI Fiber-Optic Converters with
16-Channel AES / 8-Channel Analog Audio Embed / De-Embed card (with all
models collectively referred to herein as the 9433-EMDE-ADDA).
This manual consists of the following chapters:
• Chapte r 1, “Introduction” – Provides informati on about this manual
and what is covered. Als o pr ovi des general information re gar di ng the
9433-EMDE-ADDA.
• Chapter 2, “Installation and Setup” – Provides instructio ns for
installing the 9433-EMDE-ADDA in a frame, and optionally
installing a Rear I/O Module(s).
• Chapter 3, “Operating Instructions” – Provides overviews of
operating controls and i nstru ctions for usi ng the 94 33-E MDE-ADDA.
This chapter contains the following information:
• 9433-EMDE-ADDA Card Software Versions and this Manual (p.
1-2)
• Manual Conventions (p. 1-3)
• Safety and Regulatory Summary (p. 1-5)
• 9433-EMDE-ADDA Functional Description (p. 1-6)
• Technical Sp ecifications (p. 1-10)
• Warranty and Service Information (p. 1-13)
• Contact Cobalt Dig ital Inc. (p. 1-14)
9433-E MD E-A DDA -OM (V1 .4) 9433-EMDE-ADDA PRODUCT MANUAL 1-1
1 9433-EMDE-ADDA Card Software Versions and this Manual
9433-EMDE-ADDA Card Software Versions and this Manual
When applicable, Cobalt Digital Inc. provides for continual product
enhancements through software updates. As such, functions described in this
manual may pertain specifically to cards loaded with a particular software
build.
The Software Version of your card can be checked by viewing the Ca r d I n fo
menu in DashBoard™. See Checking 9433-EMDE Card Information (p. 3-6)
in Chapter 3, “Operating Instructions” for more information. You can then
check our website for th e latest soft ware version currently released for the
card as described below.
Note: Not all functionality described in this manual may appear on cards with initial
software versions.
Check our website and proceed as follows if your card’s software does not
match the latest versi on:
Card Software earlier than
latest version
Card Software newer than
version in manual
Card is not loaded with the latest software. Not all
functions and/or specified performance described in
this manual may be available.
You can update your card with new Update software by
going to the Support>Firmware Do wnloads link at
www.cobaltdigital.com. Download “Firmware Update
Guide”, which provides simple instructions for
downloading the latest firmware for your card onto your
computer, and then uploading it to your card through
DashBoard™.
Software updates are field-installed with out an y
need to remove the card from its frame.
A new manual is expediently released whenever a
card’s software is updated and specifications
and/or functionality have changed as compared to
an earlier version (a new manual is not necessarily
released if specifications and/or functionality have not
changed). A manual earlier than a card’s softw a re
version may not completely or accurately describe all
functions available for your card.
If your card shows features not described in this
manual, you can check for the latest manual (if
applicable) and download it by going to the card’s web
page on www.cobaltdigital.com.
Cobalt Reference Guides
From the Cobalt® web home page, go to Support>Referen ce Docum ents for
easy to use guides covering network remote control, card firmware updates,
example card processing UI setups and other topics.
1-2 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Introduction Manual Conventions
Manual Conventions
In this manual, display messages and connectors are shown using the exact
name shown on the 9433-EMDE-ADDA itsel f. Examples are provi ded below.
• Card-edge display messages are shown like this:
BOOT
• Connector names are shown like this: SDI IN A
In this manual, the terms below are applicable as follows:
• 9433-EMDE-ADDA refers to the 3G/HD/SD-SDI Fiber-Optic
Converter with 16-Channel AES / 8-Channel Analog Audio Embed /
De-Embed card.
• Frame refers to the HPF-9000, OG3-FR, 8321, or similar 20-slot
frame that houses Cobalt
• Device and/or Card refers to a Cobalt
• System and/or Video System refers to the mix of interconnected
®
or other cards.
®
or other card.
production and termi nal equipment i n which the 9433-EMDE-ADDA
and other cards operate.
• Functions and/or features that are available only as an option are
denoted in th is manual like this:
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 1-3
1 Manual Conventions
Warnings, Cautions, and Notes
Certain items in this manual are highlighted by special messages. The
definitions are provided below.
Warnings
Warning messages indicate a possible hazard which, if not avoided, could
result in personal injury or death.
Cautions
Caution messages indicate a problem or incorrect practice which, if not
avoided, could result in improper operation or damage to the product.
Notes
Notes pro vide suppl emental information to the accompanying text. Notes
typically precede the text to which they apply.
Labeling Symbol Definitions
Important note regarding product usage. Failure to observe may result in
unexpected or incorrect operation.
Electronic device or assembly is susceptible to damage from an ESD event.
Handle only using appropriate ESD prevention practices.
If ESD wrist strap is not available, handle card only by edges and avoid contact
with any connectors or components.
CLASS 1 LASER PRODUCT
IEC 60825-1:2007
Caution - INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE T O
THE BEAM.
Symbol (WEEE 2002/96/EC)
For product disposal, ensure the following:
• Do not dispose of this product as unsorted municipal waste.
• Collect this product separately.
• Use collection and return systems available to you.
1-4 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Introduction Safety and Regulatory Summary
Safety and Regulatory Summary
Warnings
! WARNING !
! WARNING !
Cautions
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
• Do not stare at, or into, broken, or damaged, fibers.
• Do not stare at, or into, optical connectors.
• Only properly trained and authorized personnel should be permitted to perform laser/
fiber optic operations.
• Ensure that appropriate labels are displayed in plain view and in close proximity to the
optical port on the protective housing/access panel of the terminal equipment.
T o re duce risk of electr ic shock do not remove line voltage service barrier cover on frame
equipment containing an AC power supply. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This device is intended for environmentally controlled use only in appropriate video
terminal equipment operating environments.
This product is intended to be a component product of an openGear® frame. Refer to the
openGear® frame Owner's Manual for important safety instructions regarding the proper
installation and safe operation of the frame as well as its component products.
Heat and power distribution requirements within a frame may dictate specific slot
placement of cards. Cards with many heat-producing components should be arranged to
avoid areas of excess heat build-up, particularly in frames using only convection cooling.
The card has a moderate power dissipation (<18 W). As such, avoiding placing the card
adjacent to other cards with similar dissipation values if possible.
If required, make certain Rear I/O Module(s) is installed before installing the card into the
frame slot. Damage to card and/or Rear I/O Module can occur if module installation is
attempted with card already installed in slot.
If card resists fully engaging in rear I/O mod ule mating connec tor, check for alignment and
proper insertion in slot tracks. Damage to card and/or rear I/O module may occur if
improper card insertion is attempted.
EMC Compliance Per Market
Market Regulatory Standard or Code
United States of America FCC "Code of Federal Regulations" Title 47 Part 15, Subpart B, Class A
Canada ICES-003
International/CE CISPR 24:2010
IEC 61000-4-2:2008
IEC 61000-4-3:2006 with A1:2007 and A2:2010
IEC 61000-4-4:2004
IEC 61000-4-6:2008
CISPR 22:2008
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 1-5
1 9433-EMDE-ADDA Functional Description
9433-EMDE-ADDA Functional Description
Figure 1-1 shows functional block diagram of the 9433-EMDE-ADDA. The
card provides de-embeddi ng or embed ding bet ween unbala nced AES-3i d and
balanced analog audio discrete audio interfa ce s and SMPTE embedded audio
using full 24-bit conversion. In addition to individual per-pair embedding or
de-embedding, the card can be used to provide cross-conversions between
AES and analog discrete audio.The card also offers the built-in convenience
of either coaxial or fiber SDI I/O. Full audio crosspoints allow per-channel
gain and routing controls, as well as built-in tone generators. GUI audio
meters provide ready assessment of content presence and line-up.
The card is avai labl e wit h dis crete CWDM fiber E -O module s provid ing f ull y
error-free pat hologi cal pat tern oper ation is full y compati ble wit h profes siona l
fiber video int erfa ces wi th nu merou s CWDM wav elengt hs th at al low t he card
to be used with CWDM systems. All ancillary data is passed by the card
unaffected.
9433-EMDE-ADDA Input/Output Formats
The 9433-EMDE-ADDA provides the following inputs and outputs:
• Inputs:
• 3G/HD/SD SDI IN – 3G/HD/SD-SDI coaxial input.
• FIBER IN – 3G/HD/SD-SDI fiber input.
• AES I/O – Up to 16 channels (8 pairs) of embedding inputs from
unbalanced AES sources.
• AN_AUD I/O – Up to 8 channels of embedding inputs from
unbalanced analog audio sources (+24 dBu => 0 dBFS).
• Outputs:
• 3G/HD/SD-SDI OUT – 3G/HD/SD-SDI coaxial video output.
• FIBER OUT – 3G/HD/SD-SDI fiber output.
• AES I/O – Up to 16 channels (8 pairs) of de-embedded outputs to
unbalanced AES.
• AN_AUD I/O – Up to 8 channels of de-embedding outputs to
unbalanced analog audio (0 dBFS => +24 dBu).
1-6 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Introduction 9433-EMDE-ADDA Functional Description
3G/HD/SD-SDI
OUT
9433-EMDE-ADDA BD V1.0LB122
SDI
Fiber
(NOTE 2)
E-O
Fiber
2. Fiber EO (transmit) only on models -EOOE and -EO.
Driver
SDI Tx/
Audio
SDI Rx/
De-Embed
Fiber
Audio
Audio
Channel
Routing/
Embed
Control
AES Tx
SRC
AES Rx
(Per-Pair auto-detect
bypass for Dolby pair)
Control
Direction
AES Per-Pair
Notes: 1. Fiber OE (receive) only on models -EOOE and -OE.
ADC
Audio 24-Bit
Analog
DAC
Audio 24-Bit
Per-Pair
Switches
DIrection DIP
O-E
(NOTE 1)
Coax IN
Fiber IN
3G/HD/SD-SDI
3G/HD/SD-SDI
AES I/0
Unbalanced
(16-Ch max)
Balanced
Analog
Audio I/0
(8-Ch max)
Figure 1-1 9433-EMDE-ADDA Functional Block Diagrams
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 1-7
1 9433-EMDE-ADDA Functional Description
Audio Processor Description
The audio processor operates as an internal audio router. This function
chooses from the following inputs:
• 16 channels of embedded audio from the SDI video input (default
1-to-1 routing to SDI output).
• Up to 16 channels (8 pairs) of unbalanced (AES-3id) audio inputs or
outputs between AES I/O ports and embedded or other audio (pair
direction is controll ed via DashBoard controls).
• Up to 8 channels of balanced analog audio input s or out put s bet ween
analog input/outputs and embedded or other audio. (Analog audio
port direction is set using per-channel direction control DIP
switches.)
The audio processing subsection is built around a card internal 16-channel
audio bus. Audio embed adaptive SRC allows asynchronous 48 kHz AES
audio to automatically sy nc with progra m video 48 kHz ti ming for glitc h-fre e
embedding. Individual, per-pair SRC auto-detects and disables SRC when a
Dolby pair is detected on an input pair.
User Control Interface
Audio status (presence, dBFS signal levels) is displayed for each embedded
and AES input channel.
Figure 1-2 shows the user control interface options for the
9433-EMDE-ADDA. These options are individually described below.
Note: All user control interfaces described here are cross-compatible and can oper-
ate together as desired. Where applicable, any control setting change made
using a particular user interface is reflected on any other connected interface.
• DashBoard™ User Interface – Using DashBoard™, the
9433-EMDE-ADDA and other cards insta lled in open Gear ®
1
frames
can be controlled from a computer and monitor.
DashBoard™ allows users to view all frames on a network with
control and monitoring for all populated slots inside a frame. This
simplifies the setup and use of numerous modules in a large
installation and offers the ability to centralize monitoring. Cards
define their controllable parameters to DashBoard™, so the control
interface is always up to date.
The DashBoard™ software can be downloaded from the Cobalt
Digital Inc. website: www.cobaltdigital.com
(enter “DashBoard” in
the search window). The DashBoard™ user interface is described in
Chapter 3,“Operating Instructions”.
1. openGear® is a registered trademark of Ross Video Limited. DashBoard™ is a trademark of Ross
Video Limited.
1-8 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Introduction 9433-EMDE-ADDA Functional Description
OGCP-9000 Control Panel
or
OGCP-9000/CC Control Panel
9433-EMDE-ADDA Card
• Cobalt
®
OGCP-9000 and OGCP-9000/CC Remote Control
Panels – The OGCP-9000 and OGCP-9000/CC Remote Control
Panels conveniently and intuitively provide parameter monitor and
control of the 9433-EMDE-ADDA and other video and audio
processing terminal equipment meet ing the open-a rchitecture Co balt
cards for openGear™ standard.
In addition to circumventing the need for a computer to monitor and
control signal processing cards, the Control Panels allow quick and
intuitive acces s to hundre ds of car ds in a fac ility, a nd can monito r and
allow adjustment of multiple parameters at one time.
The Remote Control Panels are totally compatible with the
openGear™ control software DashBoard™; any changes made with
either system are reflected on the other. The Remote Control Panel
user interface is described in Chapter 3,“Operating Instructions”.
Remote Control Panel
Using the Control Panel, 9433-EMDE-ADDA
card can be remotely controlled over a LAN
20-Slot Frame with Network Controller Card
LAN
®
DashBoard™ Remote Control
Using a computer with DashBoard™
installed, 9433-EMDE-ADDA card
Computer
with NIC
Note: • To communicate with DashBoard™ or a Remote Control Panel, the frame must have a Network Controller Card installed
in the frame.
• DashBoard™ and the Remote Control Panels provide network control of the 9433-EMDE-ADDA as shown. The value
displayed at any time on the card, or via DashBoard™ or a Control Panel is the actual value as set on the card, with the
current value displayed being the actual value as effected by the card. Parameter changes made by any of these means
are universally accepted by the card (for example, a change made using the DashBoard™ controls will change the setting
displayed on a Control Panel).
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 1-9
can be remotely controlled over a
LAN
Figure 1-2 9433-EMDE-ADDA User Control Interface
In conjunction with a frame equipped
with a Network Controller Card,
9433-EMDE-ADDA card can be
remotely controlled over a LAN
1 Technical Specifications
Note: If network remote control is to be used for the frame and the frame has not yet
been set up for remote control, Cobalt
User Guide (PN 9000RCS-RM) provides thorough information and
step-by-step instructions for setting up network remote control of Cobalt
cards using DashBoard™. (Cobalt
Remote Control Panel product manuals have complete instructions for setting
up remote control using a Remote Control Panel.)
Download a copy of this guide by clicking on the Support>Reference
Documents link at www.cobaltdigital.com and then select DashBoard
Remote Control Setup Guide as a download, or contact Cobalt
Contact Cobalt Digital Inc. (p. 1-14).
9433-EMDE-ADDA Rear I/O Modules
The 9433-EMDE-ADDA physically interface s to system video connecti ons at
the rear of its frame using a Rear I/O Module.
All inputs and outputs shown in the 9433-EMDE-ADDA Functional Block
Diagrams (Figure 1- 1) enter and exit the card via the card edge backplane
connector. The Rear I/O Module breaks out the 9433-EMDE-ADDA card
edge connections to BNC and other connectors that interface with other
components and systems in the signal chain.
®
reference guide Remote Control
®
OGCP-9000 and OGCP-9000/CC
®
as listed in
®
The full assortment of 9433-EMDE-ADDA Rear I/O Modules is shown and
described in 9433-EMDE-ADDA Rear I/O Modules (p. 2-5) in Chapter 2,
“Installation and Setup”.
Technical Specifications
Table 1-1 lists the technical specifications for the 9433-EMDE-ADDA
3G/HD/SD-SDI Fiber-Optic Converters with 16-Channel AES / 8-Channel
Analog Audio Embed / De-Embed cards.
Table 1-1 Technical Specifications
Item Characteristic
Part number, nomenclature • 9433-EMDE-ADDA-EOOE 3G/HD/SD-SDI Fiber-Optic
Transceiver with 16-Channel AES / 8-Channel Analog Audio
Embed / De-Embed
• 9433-EMDE-ADDA-EO 3G/HD/SD-SDI Fiber-Optic Transmitter
with 16-Channel AES / 8-Channel Analog Audio Embed /
De-Embed
• 9433-EMDE-ADDA-OE 3G/HD/SD-SDI Fiber-Optic Receiver
with 16-Channel AES / 8-Channel Analog Audio Embed /
De-Embed
Installation/usage environment Intended for installation and usage in frame meeting openGear™
modular system definition.
Power consumption < 18 Watts maximum
1-10 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Introduction Technical Specifications
Table 1-1 Technical Specifications — continued
Item Characteristic
Installation Density Up to 20 cards per 20-slot frame
Environmental:
Operating temperature:
Relative humidity (operating or storage):
Frame communication 10/100 Mbps Ethernet with Auto-MDIX.
Indicators Card edge indicators as follows:
32° – 104° F (0° – 40° C)
< 95%, non-condensing
• Status/Error LED indicator
• Input Presence LED indicators
SDI/Fiber Inputs/Outputs
(fiber port presence per EOOE, OE, or
EO model)
Model -EOOE-WX (CWDM) Transmit
Wavelengths and Codes
(1) 75Ω BNC inputs
(1) 75Ω BNC output
SDI Receive Cable Length (1694A): 120m/180m/360m (3G/HD/
SD)
SDI Return Loss: >15 dB up to 1.485 GHz; >10 dB up to 2.970
GHz
Note: SDI Return loss and receive cable length are affected by
rear I/O module used. Specifications represent typical
performance.
Alignment Jitter: 3G/HD/SD: < 0.3/0.2/0.2 UI
Timing Jitter: 3G/HD/SD: < 2.0/1.0/0.2 UI
(1) Fiber input; LC connector
(1) Fiber output; LC connector
Fiber Wavelength, Tx: 1310 nm
Fiber Rx Sensitivity: -23 dBm; 1260 to 1620 nm
Fiber Tx Power: -5.0 dBm (min)
SDI Formats Supported: SMPTE 259M, SMPTE 292M, SMPTE
424M
Available wavelengths (in nm) are as follows: 1270, 1290, 1310,
1330, 1350, 1410, 1430, 1450, 1470, 1490, 1510, 1530, 1550,
1570, 1590, 1610.
In “WX” places in part number, code for wavelengths in each place
as listed below:
-27: 1270nm -29: 1290nm -31: 1310nm
-33: 1330nm -35: 1350nm -41: 1410nm
-43: 1430nm -45: 1450nm -47: 1470nm
-49: 1490nm -51: 1510nm -53: 1530nm
-55: 1550nm -57: 1570nm -59: 1590nm
-61: 1610nm
Audio Conversion Format 48 kHz sampling, 24-bit. Analog audio I/O conforms to
+24 dBu <=> 0 dBFS
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 1-11
1 Technical Specifications
Table 1-1 Technical Specifications — continued
Item Characteristic
Discrete Audio Inputs/Outputs (8) Unbalanced AES (AES-3id; 16-ch) with per-pair port direction
controls
(8) Balanced Analog Audio with per-pair port direction controls
Analog Audio I/O Specifications Input Impedance: >10 kΩ
Reference Level: -20 dBFS
Nominal Level: +4 dBu
Input Clip Level: +24 dBu (0 dBFS)
Freq. Response: ±0.2 dB (20 Hz to 20 kHz)
SNR: 115 dB (A weighted)
THD+N: -96 dB (20 Hz to 10 kHz)
Crosstalk: -106 dB (20 Hz to 20 kHz)
Output Impedance: < 50 Ω
Max Output Level: +24 dBu (0 dBFS)
1-12 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Introduction Warranty and Service Information
Warranty and Service Information
Cobalt Digital Inc. Limited Warranty
This product is warranted to be free from defects in material and workmanship for a period of five (5)
years from the date of shipment to the original purchaser, except that 4000, 5000, 6000, 8000 series
power supplies, and Dolby
material and workmanship for a period of one (1) year.
Cobalt Digital Inc.'s (“Cobalt”) sole obligation under this warranty sh all be limited to, at its option, (i)
the repair or (ii) replacement of the produc t, and the det ermination of whether a defect is covered under
this limited warranty shall be made at the sole discretion of Cobalt.
This limited warrant y appl ies on ly t o the origi nal end-pu rchaser of the produ ct, and i s not assign able o r
transferrable therefrom. This warr ant y i s li mited to defects in material and work ma nship, and shall not
apply to acts of God, accidents, or negligence on behalf of the purchaser, and shall be voided upon the
misuse, abuse, alteration, or modification of the product. Only Cobalt authorized factory
representatives are authorized to make repairs to the product, and any unauthorized attempt to repair
this product shall immediately void the warranty. Please contact Cobalt Technical Support for more
information.
®
modules (where applicable) are warranted to be free from defects in
To facilitate the resolut ion of warranty related issues, Cobalt recommends registering the product by
completing and returning a product registration form. In the event of a warrantable defect, the
purchaser shall notify Cobalt with a descripti on of t he p r oble m, an d Cobalt shall provide the pur ch aser
with a Re turn Mate rial Auth oriz ation (“RMA”). For retu rn, defective product s should be double boxed,
and sufficiently protecte d, in the original packa ging, or equivalent, a nd shipped to the Coba lt Factory
Service Center, postage prepaid and insured for the purchase price. The purchaser should include the
RMA number, description of the problem encountered, date purchased, name of dealer purchased
from, and serial number with the shipment.
Cobalt Digital Inc. Factory Service Center
2506 Galen Drive Office: (217) 344-1243
Champaign, IL 61821 USA Fax: (217) 344-1245
www.cobaltdigital.com Email: info@cobaltdigital.com
THIS LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES
EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE AND OF ALL OTHER OBLIGATIONS OR
LIABILITIES ON COBALT'S PART. ANY SOFTWARE PROVIDED WITH, OR FOR USE WI TH,
THE PRODUCT IS PROVIDED “AS IS.” THE BUYER OF THE PRODUCT ACKNOWLEDGES
THAT NO OTHER REPRESENTATIONS WERE MADE OR RELIED UPON WITH RESPECT TO
THE QUALITY AND FUNCTION OF THE GOODS HEREIN SOLD. COBALT PRODUCTS ARE
NOT AUTHORIZED FOR USE IN LIFE SUPPORT APPLICATIONS .
COBALT'S LIABILITY, WHETHER IN CONTRACT, TORT, WAR RANTY, OR OTHERWISE, IS
LIMITED TO THE REPAIR OR REPLACEMENT, AT ITS OPTION, OF ANY DEFECTIVE
PRODUCT, AND SHALL IN NO EVENT INCLUDE SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS), EVEN IF IT HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 1-13
1 Contact Cobalt Digital Inc.
Contact Cobalt Digital Inc.
Feel free to contact our thorough and professional suppo rt repr es entatives for
any of the following:
• Name and address of your local dealer
• Product information and pricing
• Technical support
• Upcoming trade show information
Phone: (217) 344-1243
Fax: (217) 344-1245
Web: www.cobaltdigital.com
General Information: info@cobaltdigital.com
Technical Support: support@cobaltdigital.com
1-14 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Chapter 2 Installation and Setup
Overview
This chapter contains the following information:
• Setting I/O Switches for Analog Audio (1-8) Ports (p. 2-1)
• Installing the 9433-EMDE-ADDA Into a Frame Slot (p. 2-2)
• Installing a Rear I/O Module (p. 2-3)
• Fiber and Balanced Audio Connections (p. 2-7)
• Setting Up 9433-EMDE-ADDA Network Remote Control (p. 2-8)
Setting I/O Switches for Analog Audio (1-8) Ports
Each analog channel (AN-AUD I/O 1 thru AN-AUD I/O 8) is configurable as an
input or output using the card DIP switches as shown in Figure 2-1.
Chapter 2
AN-AUD I/O 1
AN-AUD I/O 2
AN-AUD I/O 3
AN-AUD I/O 4
AN-AUD I/O 5
AN-AUD I/O 6
AN-AUD I/O 7
AN-AUD I/O 8
IN OUT
Note: All switches are set as IN (inputs) as factory default.
Top Rear of Card
Figure 2-1 AN-AUD I/O (1-8) Direction Switches
9433-E MD E-A DDA -OM (V1 .4) 9433-EMDE-ADDA PRODUCT MANUAL 2-1
2 Installing the 9433-EMDE-ADDA Into a Frame Slot
Installing the 9433-EMDE-ADDA Into a Frame Slot
CAUTION
Heat and power distribution requirements within a frame may dictate specific
slot placement of cards. Cards with many heat-producing components should
be arranged to avoid areas of excess heat build-up, particularly in frames
using only convection cooling. The card has a moderate power dissipation
(<18 W). As such, avoiding placing the card adjacent to other cards with
similar dissipation values if possible.
CAUTION
This device contains semiconductor devices which are
susceptible to serious damage from Electrostatic
Discharge (ESD). ESD damage may not be immediately
apparent and can affect the long-term reliability of the
device.
Avoid handling circuit boards in high static environments
such as carpeted areas, and when wearing synthetic fiber
clothing. Always use proper ESD handling precautions
and equipment when working on circuit boards and
related equipment.
Note: If installing the card in a slot with no rear I/O module, a Rear I/O Module
is required before cabling can be connected. Refer to Installing a Rear I/O
Module (p. 2-3) for rear I/O module installation procedure.
CAUTION
If required, make certain Rear I/O Module(s) is installed before installing the
card into the frame slot. Damage to card and/or Rear I/O Module can occur if
module installation is attempted with card already installed in slot.
Note: • Check the packaging in which the card was shipped for any extra items such
as a Rear I/O Module connection label. In some cases, this label is shipped
with the card and to be installed on the Rear I/O connector bank
corresponding to the slot location of the card.
• Before installing card or rear module, if not already fitted make certain
rear module is fitted with fiber blindmate adapter and all protective fiber port
plugs have been removed. See Fiber and Balanced Audio Connections (p.
2-7) for instructions.
Install the card into a fr ame slot as follows:
1. Determine the slot in which the card is to be installed.
2. Open the frame front access panel.
3. While holding the card by the card edges, align the card such that the
plastic ejector tab is on the bottom.
4. Align the card with the top and bottom guides of the slot in which the
card is being installed.
2-2 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Installation and Setup Installing a Rear I/O Module
5. Gradually slide the card into the slot. When resistance is noticed, gently
continue pushing the card until its rear printed circuit edge terminals
engage fully into the rear I/O module mating connector.
CAUTION
If card resists fully engaging in rear I/O module mating connector, check for
alignment and proper insertion in slot tracks. Damage to card and/or rear I/O
module may occur if improper card insertion is attempted.
Verify that the card is fully engaged in rear I/O module mating
6.
connector.
7. Close the frame front access panel.
8. Connect the input and output cables as shown in 9433-EMDE-ADDA
Rear I/O Modules (p. 2-5).
9. Repeat steps 1 through 8 for other cards.
Note: • The card BNC inputs are internally 75-ohm terminated. It is not necessary to
terminate unused BNC inputs or outputs.
• To remove a card, press down on the ejector tab to unseat the card from the
rear I/O module mating connector. Evenly draw the card from its slot.
10. If network remote control is to be used for the frame and the frame has
not yet been set up for remo te co ntr ol , perf or m se tup in acc ordance with
Setting Up 9433-EMDE-ADDA Network Remote Control (p. 2-8).
Note: If installing a card in a frame already equipped for, and connected to
DashBoard™, no network setup is required for the card. The card will be
discovered by DashBoard™ and be ready for use.
Installing a Rear I/O Module
Note: • This procedure is applicable only if a Rear I/O Module is not currently
installed in the slot where the card is to be installed. If installing the card in a
slot already equipped with a suitable I/O module, omit this procedure.
• Before installing card or rear module, if not already fitted make certain
rear module is fitted with fiber blindmate adapter and all protective fiber port
plugs have been removed. See Fiber and Balanced Audio Connections (p.
2-7) for instructions.
Install a Rear I/O Module as follows:
1. On the frame, determine the slot in which the card is to be ins t alled.
2. In the mounting area corresponding to the slot location, install
Rear I/O Module as shown in Figure 2-2.
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 2-3
2 Installing a Rear I/O Module
Align and engage mounting tab on Rear
I/O Module with the module seating slot
1
on rear of frame chassis.
Hold top of Rear I/O Module flush against
frame chassis and start the captive screw.
2
Lightly tighten captive screw.
Figure 2-2 Rear I/O Module Installation
2-4 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Installation and Setup Installing a Rear I/O Module
9433-EMDE-ADDA Rear I/O Modules
Table 2-1 shows and describes the full assortment of Rear I/O Modules
specifical ly for use with the 9433-EMDE-ADDA.
Notes: Rear I/O Modules equipped with multi-pin connectors are supplied with
removable terminal block adapters. For clarity, the adapters are omitted in
the drawings below.
Table 2-1 9433-EMDE-ADDA Rear I/O Modules
9433-EMDE-ADDA Rear I/O Module Description
CLASS 1 LASER PRODUCT - IEC 60825-1:2007. Never look into fiber connector or cable end
of device transmitting an optical signal. The transmitted light is not visible and can cause
permanent eye damage. Do not perform connection/disconnection with sending or receiving
device powered.
Note: Rear module fiber port directions (IN, OUT) are as shown below. When used on -EO or -OE models,
Fiber IN or Fiber OUT ports are respectively NC.
Provides the following connections:
• One 3G/HD/SD-SDI coaxial input BNC (SDI IN)
RM20-9433EMDE-C
• One 3G/HD/SD-SDI fiber LC input (FIBER IN)
• Eight AES-3id unbalanced audio input/outputs
(UNBAL AES I/O 1 thru AES I/O 8)
• Eight balanced analog audio input/outputs
(AN-AUD I/O 1 thru AN-AUD I/O 8)
• One 3G/HD/SD-SDI coaxial output BNC (SDI OUT)
• One 3G/HD/SD-SDI fiber LC output (FIBER OUT)
Note: AES coaxial connectors are DIN1.0/2.3 or
HD-BNC. Available equipped with High-Density
BNC (HDBNC) or DIN1.0/2.3 connectors as:
RM20-9433EMDE-C-HDBNC or
RM20-9433EMDE-C-DIN, respectively.
In previous manual version 1.2, the
UNBAL AES I/O port numbering was
labeled incorrect. Use the port
numbering shown here.
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 2-5
2 Installing a Rear I/O Module
Table 2-1 9433-EMDE-ADDA Rear I/O Modules — continue d
9433-EMDE-ADDA Rear I/O Module Description
RM20-9433EMDE-D Provides the following conne cti on s:
• One 3G/HD/SD-SDI coaxial input BNC (SDI IN)
• One 3G/HD/SD-SDI fiber LC input (FIBER IN)
• Eight balanced analog audio input/outputs
(AN-AUD I/O 1 thru AN-AUD I/O 8)
• Eight AES-3id unbalanced audio input/outputs
(UNBAL AES AUD I/O via HD-15 connector)
• One 3G/HD/SD-SDI coaxial output BNC (SDI OUT)
• One 3G/HD/SD-SDI fiber LC output (FIBER OUT)
Pinouts conform to those shown below (view shows “looking into” rear module connector)
1
11
AES Pair Cable Con nector Cable Colo r HD-15 Pin
1 (1/2) A1 BLK 11
2 (3/4) A2 RED 7
6
3 (5/6) A3 GRY 15
4 (7/8) A4 WHT 14
5 (9/10) B1 BLU 10
6 (11/12) B2 GRN 9
7 (13/14) B3 VIO 13
8 (15/16) B4 YEL 12
All GND connections are common to connector shell.
2-6 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Installation and Setup Fiber and Balanced Audio Connections
Fiber and Balanced Audio Connections
Figure 2-3 shows connect ions to the card multi-p in terminal block connect ors.
These connectors are used for card balanced audio connections. Figure 2-3
also shows how to install the blindmate fiber adapter to the rear module.
Note: It is preferable to wire connections to plugs oriented as shown in
Figure 2-3
that the orientation of rear module multi-pin audio connectors is not
necessarily consistent within a rear module, or between different rear
modules. If wiring is first connected to plug oriented as shown here, the
electrical orientation will be correct regardless of rear module connector
orientation.
rather than assessing orientation on rear module connectors. Note
Wiring insertion
+
–
G
G
+
–
holes
Removable multipin plug
view oriented with orange
release buttons to the left
Release
(orange) button
Rear module
PCB connector
+
–
G
+
–
Balanced Audio Multipin Connections
Note: • Press orange release button to insert wires
into holes.
• Wire thinner than 24 AWG may not be
securely retained in connector.
• The G terminal is shared by both ports.
Depending on wire gauge, two wires may not
fit in insertio n h o l e . In th is case, make the
bridge connection external to the multipin
plug.
• Unbalanced analog connections can be
connected across the + and G terminals. Note
that this connection will experience a 6 dB
voltage gain loss. Adjust gain for these
connections accordingly.
Fiber Adapter and Cable Connections
Installing Adapter on Card Fiber Port
The card fiber ports use a blindmate adapter which allows the card to be removed (leaving the rear module intact and installed) without
disturbing the fiber connections to the rear module. Before installing rear module or card, first install adapter to rear module as
shown below.
1
Remove protective plugs from adapter
Retaining tabs (2)
Adapter, with:
• cable locking
slots facing right
• metal retaining
tabs locking
adapter to rear
module PCB
and fiber cable ports.
Position adapter such that metal retaining
2
tabs are at rear side of rear module, and
cable locking slots on adapter are facing
right.
3
From rear of rear module, insert the
adapter into the rear module cutout hole,
making certain the two metal retaining
tabs lock the adapter into place. If tabs do
not lock the adapter, spread the tabs out
slightly.
Install the rear module into the frame.
4
Connect all cabling and fiber cables to the
5
rear module.
Install the card into the frame.
6
Figure 2-3 Fiber and Balanced Audio Connections
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 2-7
2 Setting Up 9433-EMDE-ADDA Network Remote Control
Setting Up 9433-EMDE-ADDA Network Remote Control
Perform remote control setup in accordance with Cobalt® reference guide
“Remote Control User Guide” (PN 9000RCS-RM).
Note: • If network remote control is to be used for the frame and the frame has not
yet been set up for remote control, Cobalt
Control User Guide (PN 9000RCS-RM) provides thorough information and
step-by-step instructions for setting up network remote control of Cobalt
cards using DashBoard™. (Cobalt
Remote Control Panel product manuals have complete instructions for
setting up remote control using a Remote Control Panel.)
Download a copy of this guide by clicking on the
Support>Reference Documents link at www.cobaltdigital.com and then
select DashBoard Remote Control Setup Guide as a download, or contact
®
Cobalt
• If installing a card in a frame already equipped for, and connected to
DashBoard™, no network setup is required for the card. The card will be discovered by DashBoard™ and be ready for use.
as listed in Contact Cobalt Digital Inc. (p. 1-14).
®
®
reference guide Remote
OGCP-9000 and OGCP-9000/CC
®
2-8 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Overview
Chapter 3
Chapter 3 Operating Instructions
This chapter contains the following information:
If you are already familiar with
using DashBoard or a Cobalt
Remote Control Panel to control
Cobalt cards, please skip to
9433-EMDE Function Menu List
and Descriptions (p. 3-7).
• Control and Display Descriptions (p. 3-1)
• Accessing the 9433-EMDE Card via Remote Control (p. 3-4)
• Checking 9433-EMDE Card Information (p. 3-6)
• 9433-EMDE Function Menu List and Descriptions (p. 3-7)
• Troubleshooting (p. 3-13)
Control and Display Descriptions
This secti on describes the user interface controls, indicators, and displays for
using the 9433-EMDE-ADDA card. The 9433-EMDE-ADDA functions can
be accessed and controlled using any of the user interfaces described here.
The format in which the 9433-EMDE-ADDA functional controls, indicators,
and displays appear and are used varies depending on the user int er fac e be ing
used. Regardless of the user interface being used, access to the
9433-EMDE-ADDA functions (and the controls, indicators, and displays
related to a particular function) follows a general arrangement of Function
Menus under which related c ontrols ca n be accesse d (as descri bed in Funct ion
Menu/Parameter Overview below).
Note: When a setting is changed, settings displayed on DashBoard™ (or a Remote
Control Panel) are the settings as effected by the card itself and reported back
to the remote control; the value displayed at any time is the actual value as set
on the card.
9433-E MD E-A DDA -OM (V1 .4) 9433-EMDE-ADDA PRODUCT MANUAL 3-1
3 Control and Display Descriptions
Function Menu/Parameter Overview
The functions and related parameters available on the 9433-EMDE-ADDA
card are organized i nto func tion menus, which consi st of parameter gr oups as
shown below.
Figure 3-1 shows how the 9433-EMDE car d and i ts men us are or ganized, and
also provides an overview of how navigation is performed between cards,
function menus, and parameters.
If using DashBoard™ or a Remote Control Panel, the
desired 9433-EMDE card is first selected.
9433-EMDE-ADDA
Menu a Menu b
Individual Parameters
Each menu consists of groups of parameters related
to the function menu. Using the “Output Audio
Routing” function menu example, the individual
parameters for this function consist of various routing
parameters such as channel source, gain, and so on.
Figure 3-1 Function Menu/Parameter Overview
• • •
The desired function menu is next selected.
Function Menus consist of parameter groups
related to a particular 9433-EMDE card
function (for example, “Output Audio
Routing”).
Menu z
3-2 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Operating Instructions Control and Display Descriptions
DashBoard™ User Interface
(See Figure 3-2.) The card function menus are organized in DashBoard™
using tabs. When a tab is selected, each parametric control or selection list
item associated with the function is displayed. Scalar (numeric) parametric
values can then be adjusted as desired using the GUI slider controls. Items in
a list can then be selected using GUI drop-down lists.
DashBoard Tabs
Typical Selection List
Typical Button Control
DashBoard Sub-Tab
Figure 3-2 Typical DashBoard Tabs and Controls
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 3-3
Typical Parametric Control
Level Bar Graph Meters
3 Accessing the 9433-EMDE Card via Remote Control
Accessing the 9433-EMDE Card via Remote Control
Access the 9433-EMDE card using Das hBoard™ or Cobal t® Remote Control
Panel as described below.
Accessing the 9433-EMDE Card Using DashBoard™
1. On the computer connected to the frame LAN, open DashBoard™.
2. As shown below, in the left side Basic View Tree locate the Network
Controller Card associated with the frame containing the 9433-EMDE
card to be accessed (in this example, “MFC-8320-N SN: 00108053”).
3. As shown below, expand the tree to access the cards within the frame.
Click on the card to be a cce sse d (in this example, “Slot 6: 9433-EMDE”).
.
As shown on the next page, when the card is accessed in DashBoard™
its function menu screen showing tabs for each function is displayed.
(The particular menu scr een di splaye d i s the previo usly di splay ed s creen
from the last time the card was accessed by DashBoard™).
3-4 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Operating Instructions Accessing the 9433-EMDE Card via Remote Control
Card Access/Navigation
Tree Pane
Card Info
Pane
Card Function Menu and
Controls Pane
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 3-5
3 Checking 9433-EMDE Card Information
Checking 9433-EMDE Card Information
The operating status and software version the 9433-EMDE card can be
checked using DashBoard™ or the card edge control user interface. Figure
3-3 shows and describes the 9433-EMDE card information screen using
DashBoard™ and accessing card infor mation using the card edg e control user
interface.
Note: Proper operating status in DashBoard™ is denoted by green icons for the sta-
tus indicators shown in Figure 3-3. Yellow or red icons respectively indicate
an alert or failure condition. Refer to Troubleshooting (p. 3-13) for corrective
action.
The Tree View shows the cards seen by
DashBoard™. In this example, Network
Controller Card is hosting a 9433-EMDE
card in slot 12.
Status Display
This displays shows the status and format
of the signals being received by the
9433-EMDE, as well as card status.
This display also shows the the card
hardware and software version info.
Figure 3-3 9433-EMDE Card Info/Status Utility
3-6 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Operating Instructions 9433-EMDE Function Menu List and Descriptions
9433-EMDE Function Menu List and Descriptions
Table 3-1 individually lists and describes each 9433-EMDE function menu
and its related list selections, co ntrols, and parameters . Where helpful,
examples showing usage of a function are also provided. Table 3-1 is
primarily based upon using DashBoard™ to access each function and its
corresponding menus and parameters.
Note: All numeric (scalar) parameters displayed on DashBoard™ can be changed
using the slider controls, arrows, or by numeric keypad entry in the
corresponding numeric field. (When using numeric keypad entry, add a return
after the entry to commit the entry.)
On DashBoard™ itself and in Table 3-1, the function menu items are
organized using tabs as shown below.
Some functions use sub-tabs to help maintain clarity and organization. In these
instances, Table 3-1 shows the ordinate tab along with its sub-tabs. Highlighted
sub-tabs indicate that controls described are found by selecting this sub-tab (in this
example, the Embedded sub-tab on the Output Audio Routing page).
The table below provides a quick-reference to the page numbers where each
function menu item can be found.
Function Menu Item Page Function Menu Item Page
Input Video Controls 3-8 Output Audio Routing 3-9
Input Audio Status 3-8
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 3-7
3 9433-EMDE Function Menu List and Descriptions
Table 3-1 9433-EMDE Function Menu List
(-OE and -EOOE only) Allows selection of card video
input from SDI (coax) or Fiber inputs. Also shows
Input Video Controls
Input Audio Status
Individual signal status and peak level displays for embedded audio input pairs, AES, and analog input pairs as described below.
AES pair status also shows sample rate.
• Absent: Indicates embedded channel or AES pair does not contain recognized audio PCM data.
• Present PCM: Indicates AES pair or embedded channel contains recognized audio PCM data. Running per-channel peak
level is also displayed (Dolby data will show as “PCM” but will exhibit a steady per-pair 0 dBFS level).
Note: AES Dolby-encoded inputs are directed via a special path that automatically bypasses SRC.
status (OK and format received) or no input conditions.
Displays signal status and payload for embedded and
discrete audio received by the card. Also provides AES
port user direction indication/control.
Channel-pair AES port
user direction indicator/
controls.
Note: Direction indicator/
controls are ganged with
same controls on Output
Audio Routing page.
3-8 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Operating Instructions 9433-EMDE Function Menu List and Descriptions
Table 3-1 9433-EMDE Function Menu List — continued
Provides source selection, gain, mute, and audio meters for
embedded destination (output) channels.
Output Audio Routing
Output Audio crosspoints are available for
embedded, AES 75 (AES-3id), and analog output
Input Audio
AES 75 Ch 5/6
Analog Ch 1/2
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 3-9
Crosspoint
Emb Ch 1
Emb Ch 2
Emb Ch 3
Emb Ch 4
Emb Ch 5
Emb Ch 6
Emb Ch 7
Emb Ch 8
Emb Ch 9
Emb Ch 10
•
•
•
Emb Ch 16
Card Embedded
Audio Output
destination channels.
The example above shows various Source
selections that direct various source choices to Emb
Ch 1 thru Ch 16 destination output channels (unused
channels can be set to Silence or Mute if desired).
Each output channel provides Gain and Mute
controls as well as level meters. Several internal
tones generator sources can also be routed to an
output channel.
Note: Analog audio channel can function as input or
output. If intending to embed and analog audio
channel, make certain channel direction DIP
switches for intended channels are set as IN. See
Setting I/O Switches for Analog Audio (1-8) Ports (p.
2-1) in Chapter 2, “Installation and Setup”.
3 9433-EMDE Function Menu List and Descriptions
Table 3-1 9433-EMDE Function Menu List — continued
(continued)
Note: •
Default factory preset routing routes as pass-thru embedded Ch 1 thru Ch 16 to Emb Ch 1 thru Emb Ch 16.
• Emb Ch 2 thru Emb Ch 16 have controls identical to the controls described here for Emb Ch 1. Therefore, only the
Emb Ch 1 controls are shown here.
• Embedded Audio Channel Source Select Using the Source drop-down list, selects the audio input source to be
• Channel Mute/Gain Contr o ls a n d Pe ak
Level Display
routed to the respective embedded output channel from the following
choices:
• Embedded input channel 1 thru 16 (Embedded Ch 1 thru
Embedded Ch 16)
• AES 75 (AES-3id) input channel 1 thru 16 (AES 75 Ch 1 thru AES 75
Ch 16)
• Analog audio input channel 1 thru 8 (Analog Ch 1 thru
Analog Ch 8)
• Built-in Tone generators Tone 100 Hz thru Tone 16 kHz
(all are -20 dBFS level; freq (Hz) in ascending order are 100, 200, 300,
400, 500, 600, 700, 800, 900, 1k, 2k, 4k, 6k, 8k, 12k, and 16k)
• Silence
Note: • AES pair sourcing is dependent on rear I/O module used. Current
rear modules may not support full input complement.
• AES pair selection should be boundary pairs applied to normal
boundary pairs of embedded destinations.
• For embedding from analog, make certain channel direction DIP
switches for intended channels are set as IN. See Setting I/O
Switches for Analog Audio (1-8) Ports (p. 2-1) in Chapter 2,
“Installation and Setup”.
Provides Mute channel controls, as well as peak level meter for each
output channel. (Meter shows level as affected by Level control.)
Gain controls allow relative gain (in dB) control for the corresponding
destination Embedded Audio Group channel.
(-80 to +20 dB range in 1.0 dB steps; unity = 0 dB)
®
Note: Although the card can pass non-PCM data such as Dolby
AC-3, setting the gain control to any setting other than default 0 will
corrupt Dolby data.
E or
3-10 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Operating Instructions 9433-EMDE Function Menu List and Descriptions
Table 3-1 9433-EMDE Function Menu List — continued
Provides source selection, gain, mute, and audio meters for
AES 75 destination (output) channels.
Note:
AES 75 Ch 2 thru Ch 16 have controls identical to the controls described here for AES 75 Ch 1. Therefore, only the
AES 75 Ch 1 controls are shown here.
• AES Pair Direction Select and Au dio
Channel Source Select
• Channel Mute/Gain Controls and Peak
Level Display
Input (Out put) buttons set an AES pair as an input or output (in this
example, AES 75 pair 1/2 set as Output).
Note: AES pair input/output selection also shown and controllable via
similar controls on the Input Audio Status page.
Using the Source drop-down list, selects the audio input source to be
routed to the corresponding destination channel from the following
choices:
• Embedded input channel 1 thru 16 (Embedded Ch 1 thru
Embedded Ch 16)
• AES 75 (AES-3id) input channel 1 thru 16 (AES 75 Ch 1 thru AES 75
Ch 16)
• Analog audio input channel 1 thru 8 (Analog Ch 1 thru
Analog Ch 8)
• Built-in Tone generators Tone 100 Hz thru Tone 16 kHz
(all are -20 dBFS level; freq (Hz) in ascending order are 100, 200, 300,
400, 500, 600, 700, 800, 900, 1k, 2k, 4k, 6k, 8k, 12k, and 16k)
• Silence
Note: • AES pair sourcing is dependent on rear I/O module used. Current
rear modules may not support full input complement.
• AES pair selection should be boundary pairs applied to normal
boundary pairs of embedded destinations.
• For embedding from analog, make certain channel direction DIP
switches for intended channels are set as IN. See Setting I/O
Switches for Analog Audio (1-8) Ports (p. 2-1) in Chapter 2,
“Installation and Setup”.
Provides Mute channel controls, as well as peak level meter for each
output channel. (Meter shows level as affected by Level control.)
Gain controls allow relative gain (in dB) control for the corresponding
destination AES channel.
(-80 to +20 dB range in 1.0 dB steps; unity = 0 dB)
®
Note: Although the card can pass non-PCM data such as Dolby
AC-3, setting the gain control to any setting other than default 0 will
corrupt Dolby data.
E or
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 3-11
3 9433-EMDE Function Menu List and Descriptions
Table 3-1 9433-EMDE Function Menu List — continued
Provides source selection, gain, mute, and audio meters for
Analog Out destination (output) channels.
Note:
• Analog Out Ch 2 thru Ch 8 have controls identical to the controls described here for Analog Out Ch 1. Therefore,
only the AES 75 Ch 1 controls are shown here.
• For de-embedding to analog, make certain channel direction DIP switches for intended channels are set as OUT
(switches are default set to the IN position). See Setting I/O Switches for Analog Audio (1-8) Ports (p. 2-1) in
Chapter 2, “Installation and Setup”.
• Analog Audio Out Channel Source Se lect Using the Source drop-down list, selects the audio input source to be
• Channel Mute/Gain Contr o ls a n d Pe ak
Level Display
routed to the respective analog output channel from the following
choices:
• Embedded input channel 1 thru 16 (Embedded Ch 1 thru
Embedded Ch 16)
• AES 75 (AES-3id) input channel 1 thru 16 (AES 75 Ch 1 thru AES 75
Ch 16)
• Analog audio input channel 1 thru 8 (Analog Ch 1 thru
Analog Ch 8)
• Built-in Tone generators Tone 100 Hz thru Tone 16 kHz
(all are -20 dBFS level; freq (Hz) in ascending order are 100, 200, 300,
400, 500, 600, 700, 800, 900, 1k, 2k, 4k, 6k, 8k, 12k, and 16k)
• Silence
Note: AES pair sourcing is dependent on rear I/O module used. Current
rear modules may not support full input complement.
Provides Mute channel controls, as well as peak level meter for each
output channel. (Meter shows level as affected by Level control.)
Gain controls allow relative gain (in dB) control for the corresponding
destination Embedded Audio Group channel.
(-80 to +20 dB range in 1.0 dB steps; unity = 0 dB)
Note: Maximum absolute analog output is limited to +24 dBu.
3-12 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Operating Instructions Troubleshooting
Troubleshooting
This section provides general troubleshooting information and specific
symptom/c orrective action for the 9433-EMDE card and its remote control
interface. The 9433-EMDE card requires no periodic maintenance in its
normal operation; if any er ror indication (as descr ib ed in this section) occurs,
use this section to correct the condition.
Error and Failure Indicator Overview
The 9433-EMDE card itself and its remote control system s all (to varying
degrees) provide error and failure indications. Depending on how the
9433-EMDE card is being used (i.e, st andalone or networ k controlled through
DashBoard™ or a Remote Control Panel), check all available indications in
the event of an error or failure condition. The various 9433-EMDE card and
remote control error and failure indicators are individually described below.
Note: The descriptions below provide general information for the various status and
error indicators. For specific failures, also use the appropriate subsection
listed below.
• Basic Troubleshooting Checks (p. 3-16)
• 9433-EMDE Processing Error Troubleshooting (p. 3-16)
• Troubleshooting Network/Remote Control Errors (p. 3-17)
9433-EMDE Card Edge Status/Error Indicators and Display
Figure 3-4 shows and describes the 9433-EMDE card edge status indicators
and display. These indicators and th e dis play s how stat us and erro r c onditi ons
relating to the card itself and remote (network) c ommunications (where
applicable). Because these indicators are part of the card itself and require no
external interface, the indicators are particularly useful in the event of
communications problems with external devices such as network remote
control devices.
3G
SD
HD
GRP1
GRP2
GRP3
COM
ERR
Status/Error
Indicators
Input Status
Item Function
COM LED Blue LED flashes when 9433-EMDE is receiving control message from remote network control (e.g.,
ERR LED This function is currently reserved.
Input Status
LEDs
Note: The input status LEDs may not be configured and functional on initial product release.
DashBoard™ or Cobalt
Three blue LEDs indicate SDI input presence and format (3G, HD, SD) of currently selected input.
Four blue LEDs indicate presence (lock) of the four embedded audio groups on the card SDI input (GRP1,
GRP2, GRP3, GRP4).
®
Remote Control Panel)
GRP4
Indicators
Figure 3-4 9433-EMDE Card Edge Status Indicators and Display
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 3-13
3 Troubleshooting
DashBoard™ Status/Error Indicators and Displays
Figure 3-5 shows and describes the DashBoard™ status indicators and
displays. These indicator icons and displays show status and error conditions
relating to the 9433-EMDE card itself and re mote (networ k) communication s.
Indicator Icon or Display Error Description
Red indicator icon in Card Access/Navigation Tree pane shows card with Error
condition (in this example, the Card Access/Navigation Tree pane shows a general
error issued by the 9433-EMDE card in slot 6).
Specific errors are displayed in the Card Info pane (in this example “No connection
to device” indicating 9433-EMDE card is not connecting to frame/LAN).
If the 9433-EMDE card is not connecting to the frame or LAN, all controls are
grayed-out (as shown in the example here).
Gray indicator icon in Card Access/Navigation Tree pane shows card(s) are not
being seen by DashBoard™ due to lack of connection to frame LAN (in this
example, both a 9433-EMDE card in slot 6 and the MFC-8320-N Network Controller
Card for its frame in slot 0 are not being seen).
Yellow indicator icon in Card Access/Navigation Tree pane shows card with Alert
condition (in this example, the Card Access/Navigation Tree pane shows a general
alert issued by the MFC-8320-N Network Controller Card).
Clicking the card slot position in the Card Access/Navigation Tree (in this example
Network Controller Card “Slot 0: MFC-8320-N”) opens the Card Info pane for the
selected card. In this example, a “Fan Door Open” specific error is displayed.
Yellow indicator icon in 9433-EMDE Card Info pane shows error alert, along with
cause for alert (in this example, the 9433-EMDE is not receiving a video input for the
selected input source).
Figure 3-5 DashBoard™ Status Indicator Icons and Displays
3-14 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Operating Instructions Troubleshooting
Access Card Info panes for specific cards by clicking the card slot position in
the Card Access/Navigation Tree pane (as shown in the example in Figure
3-6).
By clicking on “Slot 0: MFC-8320-N”
in this example, Card Info is
displayed for frame Network
Controller Card
By clicking on “Slot 12:
CDI-9433-EMDE” in this
example, Card Info is shown
for 9433-EMDE card in slot 12
Status for selected card is
shown here (in this
example, connection OK
and “Fan Door Open”
alert)
Card general information
is displayed in lower
portion of Card Info pane
Status for selected
card is shown here
(in this example, all
indications are OK)
Where applicable,
additional status is
displayed (as shown in
this example)
Figure 3-6 Selecting Specific Cards for Card Info Status Display
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 3-15
3 Troubleshooting
Basic Troubleshooting Checks
Failures of a general nature (affecting many cards and/or functions
simultaneously), or gross inoperability errors are best addressed first by
performing basic checks before proceeding further. Table 3-2 provides basic
system checks that typically locate the source of most general problems. If
required and applicable, perform further troubleshooting in accordance with
the other troubleshooting tables in this section.
Table 3-2 Basic Troubleshooting Checks
Item Checks
Verify pow er presence and
characteristics
Check Cable connection
secureness and connecting
points
Card seating within slots Make certain all cards are properly seated within its frame slot. (It is best to
Check status indicators and
displays
Troubleshoot by
substitution
On both the frame Network Controller Card and the 9433-EMDE, in all cases
when power is being properly supplied there is always at least one indicator
illuminated. Any card showing no illuminated indicators should be cause for
concern.
Make certain all cable connections are fully secure (including coaxial cable
attachment to cable ferrules on BNC connectors). Also, make certain all
connecting points are as intended. Make certain the selected connecting
points correlate to the intended card inputs and/or outputs. Cabling mistakes
are especially easy to make when working with large I/O modules.
assure proper seating by ejecting the card and reseating it again.)
On both DashBoard™ and the 9433-EMDE card edge indicators, red
indications signify an error condition. If a status indicator signifies an error,
proceed to the following tables in this section for further action.
All cards within the frame can be hot-swapped, replacing a suspect card or
module with a known-good item.
9433-EMDE Processing Error Troubleshooting
Table 3-3 provides 9433-EMDE processing troubleshooting information. If
the 9433-EMDE card exhibi ts any of t he symptoms l isted in Table 3-3, follow
the troubleshooting instructions provided.
In the majority of cases, most errors are caused by simple errors where the
9433-EMDE is not appropriately set for the type of signal being received by
the card.
Note: • The error indications shown below are typical for the corresponding error
conditions listed. Other error indications not specified here may also be displayed on DashBoard™ and/or the 9433-EMDE card edge status indicators.
• Where errors are displayed on both the 9433-EMDE card and network
remote controls, the respective indicators and displays are individually
described in this section.
3-16 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Operating Instructions Troubleshooting
Table 3-3 Troubleshooting Processing Errors by Symptom
Symptom Error/Condition Corrective Action
• DashBoard™ shows
Unlocked message in
9433-EMDE Status pane
• Card edge Input LED
corresponding to input is not
illuminated
Audio not processed or passed
through card
Dolby audio corrupted or
unrecognized by downstream
device
No video input present Make certain intended video source is
• AES port not set as input or
output as intended
• Analog audio port switches
not set for intended usage
Audio Output Routing Gain
control(s) for port set to setting
other than unity gain ( 0.0 dB)
Troubleshooting Network/Remote Control Errors
connected to appropriate 9433-EMDE card
video input. Make certain BNC cable
connections betw een frame Rear I/O Modu le for
the card and signal source are OK.
On Input Audio Status or Output Audio
Routing tab, make certain port direction setting
matches desired direction.
Analog audio Ch 1 thru Ch 8 use DIP switches
on the card PCB to set intended direction (IN or
OUT). See Setting I/O Switches for Analog
Audio (1-8) Ports (p. 2-1) in Chapter 2,
“Installation and Setup” for instructions.
Although the card can p a ss no n-PCM da t a s uc h
as Dolby® E or AC-3, setting the gain control to
any setting other than default 0 will corrupt
Dolby data.
In Case of Problems
Refer to Cobalt® reference guide “Remote Control User Guide” (PN
9000RCS-RM) for network/remote control troubleshooting information.
Should any problem arise with this product that was not solved by the
information in this section, please contact the Cobalt Digital Inc. Technical
Support Department.
If required, a Return Material Authorizatio n num ber (RMA) will be issued to
you, as well as specific shipping instructions. If required, a temporary
replacement item will be made available at a nominal charge. Any shipping
costs incur r ed are the customer’s responsibility. All products shipped to you
from Cobalt Digital Inc. will be shipp ed collect.
The Cobalt Digital Inc. Technical Support Department will continue to
provide advice on any product manufactured by Cobalt Digital Inc., beyond
the warranty period without charge, for the life of the product.
See Contact Cobalt Digi tal Inc. (p. 1-14) in Chapter 1, “Introduction“ for
contact information.
9433-EMDE-ADDA-OM (V1.4) 9433-EMDE-ADDA PRODUCT MANUAL 3-17
This page intentionally blank
3-18 9433-EMDE-ADDA PRODUCT MANUAL 9433-EMDE-ADDA-OM (V1.4)
Cobalt Digital Inc.
2506 Galen Drive
Champaign, IL 61821
Voice 217.344.1243 • Fax 217.344.1245
www.cobaltdigital.com
9433-EMDE-ADDA-OM (V1.4) Printed in USA
Loading...