Cobalt Digital SDI-To-Analog HD User Manual

1 2 3 4 5 6

YPbPr Video Out; SMPTE

YPbPr Video Out; Betacam

YPbPr Video Out; MII

RGB Video Out

Composite Video Out; CVBS + Y/C

Composite Video Out; CVBS + Y/C PAL-M

Composite Video Out; 3X CVBS

Composite Video Out; 3X CVBS PAL-M

SD Composite; Pedestal Off

SD Composite; Pedestal On

De-Embed Emb 1/2

De-Embed Emb 3/4

De-Embed Emb 5/6

De-Embed Emb 7/8

1 2 3 4 5 6

OFF

SCPD2012P27

Cobalt Digital Inc.

2406 E. University Ave. Urbana, IL 61802 Voice 217.344.1243 • Fax 217.344.1245 www.cobaltdigital.com

SDI-To-Analog Con verte r

HD/SD-SDI-to-Analog Video with Audio De-Embedder

The BlueBox™ SDI-To-Analog Converter (hereinafter “BlueBox™ SDI>Analog”) provides a small “throwdown” package that offers HD/SD-SDI to analog video-audio conversion. Component and composite conversions are available, with support for NTSC/PAL CVBS, and PAL-M CVBS outputs. The supported SDI input formats are listed below.

• 1920 x 1080i 50/5994/60

• 1920 x 1080psf 2398/24/25/2997/30

• 1280 x 720p50/5994/60

Note: BlueBox™ SDI>Analog does not perform format cross, up, or down-conversions. Selected video output mode must be set to be compatible with input (e.g., CVBS modes are compatible only with SD-SDI input). The unit receives its DC power from either connecting its USB port to associated equipment, or by the supplied AC adapter.

SDI

SDI IN

De-serialize

Audio

De-embed

Connecting BlueBox™ SDI>Analog

1 Connect BlueBox™ Analog>SDI to DC power using either or both the USB port or the

supplied AC adapter. Dual source (simultaneous) use provides power redundancy. Note: USB connection derives only DC operating power from USB port. This connection

does not provide remote control or monitoring.

2. Connect SDI input and analog output. This provides the basic conversion connections. Other connections do not require termination if unused.

Video Output Modes

BlueBox™ SDI>Analog provides highly flexible output mode selection using DIP switch positions SW1 thru SW4, offering the modes listed below. Refer to diagram on rear page or label on unit for switch positions. Connector port functions depend on mode selection (see unit label).

HD Modes SD Modes

• YPbPr

•RGB

Note: CVBS modes provide a 1x3 D A, w ith C VBS outp ut on a ll three BNC v ide o outp uts . Sel ecta ble NTSC pedestal On/Off for CVBS modes.

• YPbPr, SMPTE levels

• YPbPr, Betacam™ levels

• YPbPr, MII leve ls

• 720 x 480i5994 (SD-NTSC)

• 720 x 576i50 (SD-PAL)

SDI RCK/

Driver

Video

D/A

Audio

DAC

SDI RCK OUT

AN-AUD OUT (2-ch)

• Y/C (NTSC/PAL and PAL-M)

• CVBS (NTSC/PAL and PAL-M)

Y G CVBS CVBS Pb B Y CVBS Pr R C CVBS

Output line-up depends on mode setting; see text

Audio De-Embedding

BlueBox™ SDI>Analog provides de-embedding of SDI embedded channel pairs 1/2, 3/4, 5/6, or 7/8 from the SDI input to analog audio outputs AUDIO OUT (L/R) RCA connectors. Refer to diagram on rear page or label on unit for switch positions.

Unbalanced Audio Levels and This Device

The unbalanced “RCA” audio outputs on this device correspond to 2.2 Vrms output when sourced from a unity-gain 0 dBFS digital sine-wave source. Consumer audio is specified in dBV with a nominal (or recording) level of -10 dBV. The 2 Vrms maximum output level corresponds to +6 dBV. The unbalanced analog outputs on this device allow for 16 dB of headroom above the nominal -10 dBV consumer level (“headroom” is the range between the maximum and nominal audio levels).

Professional balanced analog audio levels in the US typically use a +4 dBu nominal level with 20 dB of headroom (-20 dBFS). The maximum level for balanced analog interfaces is +24 dBu.

The headroom difference between consumer and professional audio will result in a lower RCA consumer level when converting from professional balanced analog audio. For example, if pro level analog audio is received and transmitted via AES or embedded SDI to a receiver converting to RCA analog audio, the output will be 4 dB lower, with a nominal level of -14 dBV.

Status Indicator

BlueBox™ SDI>Analog has a Status LED on the side of the unit which functions as follows:

• Solid ON – Input lock OK.

• Slow Flash – Unlocked to input video; input video not present

Specifications

Item Description/Specification

Standards supported: Inputs:

Receiver EQ Performance

Outputs:

Audio conversion format: Power source:

Dimensions (WxHxD):

SMPTE 259M, 292M

- HD/SD-SDI, 75Ω BNC

- DC Power (+5 VDC via USB or adapter) HD: 200m of Belden 1694A (or equivalent)

SD: >300m of Belden 1694A (or equivalent)

- Analog video (selectable as component, CVBS+Y/C, or 3x CVBS)

- Reclocked SDI, 75Ω BNC

- Analog audio out L/R pair, unbalanced “consumer” level RCA 48 kHz sampling, 24-bit 5-16 VDC, 2.4 W. Power-sourced directly from host equipment USB port. Can

also be powered using corded AC adapter (included).

5.5" x 3" x 1" (including connector projections) (139 x 77 x 26 mm)

Warranty and Service Information

Cobalt Digital In c . Limited Warranty

This product is warranted to be free from defects in material and workmanship for a period of five (5) years from the date of shipment to the original purchaser, except that 4000, 5000, 6000, 8000, and Blue Box series power supplies, and Dolby material and workmanship for a period of one (1) year.

Cobalt Digital Inc.'s (“Cobalt”) sole obligation under this warranty shall be limited to, at its option, (i) the repair or (ii) replacement of the product, and the determination of whether a defect is covered under this limited warranty shall be made at the sole discretion of Cobalt.

This limited warranty applies only to the original end-purchaser of the product, and is not assignable or transferrable therefrom. This warranty is limited to defects in material and workmanship, and shall not apply to acts of God, accidents, or negligence on behalf of the purchaser, and shall be voided upon the misuse, abuse, alteration, or modification of the product. Only Cobalt authorized factory representatives are authorized to make repairs to the product, and any unauthorized attempt to repair this product shall immediately void the warranty. Please contact Cobalt Technical Support for more information.

To facilitate the resolution of warranty related issues, Cobalt recommends registering the product by completing and returning a product registration form. In the event of a warrantable defect, the purchaser shall notify Cobalt with a description of the problem, and Cobalt shall provide the purchaser with a Return Material Authorization (“RMA”). For return, defective products should be double boxed, and sufficiently protected, in the original packaging, or equivalent, and shipped to the Cobalt Factory Service Center, postage prepaid and insured for the purchase price. The purchaser should include the RMA number, description of the problem encountered, date purchased, name of dealer purchased from, and serial number with the shipment.

Cobalt Digital Inc. Factory Service Center 2406 E. University Avenue Office: (217) 344-1243 Urbana, IL 61802 USA Fax: (217) 344-1245 www.cobaltdigital.com Email: info@cobaltdigital.com

THIS LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON COBALT'S PART. ANY SOFTWARE PROVIDED WITH, OR FOR USE WITH, THE PRODUCT IS PROVIDED “AS IS.” THE BUYER OF THE PRODUCT ACKNOWLEDGES THAT NO OTHER REPRESENTATIONS WERE MADE OR RELIED UPON WITH RESPECT TO THE QUALITY AND FUNCTION OF THE GOODS HEREIN SOLD. COBALT PRODUCTS ARE NOT AUTHORIZED FOR USE IN LIFE SUPPORT APPLICATIONS.

COBALT'S LIABILITY, WHETHER IN CONTRACT, TORT, WARRANTY, OR OTHERWISE, IS LIMITED TO THE REPAIR OR REPLACEMENT, AT ITS OPTION, OF ANY DEFECTIVE PRODUCT, AND SHALL IN NO EVENT INCLUDE SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS), EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

modules (where applicable) are warranted to be free from defects in

the express written permission of Cobalt Digital Inc. This manual and any information contained within, may not be reproduced, distributed, or transmitted in any form, or by any means, for any purpose, without the express written permission of Cobalt Digital Inc. Reproduction or reverse engineering of software used in this device is prohibited.

The information in this document has been carefully examined and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Cobalt Digital Inc. reserves the right to make changes to any products herein to improve readability, function, or design. Cobalt Digital Inc. does not assume any liability arising out of the application or use of any product or circuit described herein.

Cobalt

is a registered trademark of Cobalt Digital Inc. BlueBox™ is a trademark of Cobalt Digital Inc.