Cobalt Digital COMPASS 9032 User Manual

Cobalt Digital Inc.

9032

Analog to Digital Converter with Frame

Synchronization

9032-OM Version: 2.1

Owner’s Manual

9032 •••• HD/SD Analog to Digital Converter with Frame Sync Owner’s Manual

• Cobalt Part Number: 9032-OM

• Document Version: 2.1

• Printed in the United States.

• Last Author: CGG

• Printing Date: 1/8/2013

The information contained in this Owner’s Manual is subject to change without notice or obligation.

Cobalt Digital Inc. Reproduction or reverse engineering of copyrighted software is prohibited.

Notice

The material in this manual is furnished for informational use only. It is subject to change without notice and should not be construed as a commitment by Cobalt Digital Inc. Cobalt Digital Inc assumes no responsibility or liability for errors or inaccuracies that may appear in this manual.

Trademarks

• is a registered trademark of Ross Video Limited.

•

• All other product names and any registered and unregistered trademarks mentioned in this

manual are used for identification purposes only and remain the exclusive property of their respective owners.

is a registered trademark of Cobalt Digital Inc.

Page 2 of 26 9032 Owner’s Manual •••• (V 2.1)

Important Regulatory and Safety Notices

Before using this product and any associated equipment, refer to the “Important Safety Instructions” listed below so as to avoid personnel injury and to prevent product damage.

Products may require specific equipment, and /or installation procedures be carried out to satisfy certain regulatory compliance requirements. Notices have been included in this publication to call attention to these specific requirements.

Symbol Meanings

Warning

Caution

Notice

ESD

Susceptibility

This symbol on the equipment refers you to important operating and maintenance (servicing) instructions within the Product Manual Documentation. Failure to heed this information may present a major risk of damage or injury to persons or equipment.

The symbol with the word “Warning” within the equipment manual indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury.

The symbol with the word “Caution” within the equipment manual indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.

The symbol with the word “Notice” within the equipment manual indicates a situation, which if not avoided, may result in major or minor equipment damage or a situation which could place the equipment in a non-compliant operating state.

This symbol is used to alert the user that an electrical or electronic device or assembly is susceptible to damage from an ESD event.

Important Safety Instructions

Caution

Warning

This product is intended to be a component product of the openGear to the openGear the proper installation and safe operation of the frame as well as it’s component products.

Certain parts of this equipment namely the power supply area still present a safety hazard, with the power switch in the OFF position. To avoid electrical shock, disconnect all A/C power cords from the chassis' rear appliance connectors before servicing this area.

frame Owner’s Manual for important safety instructions regarding

frame. Refer

Warning

9032 Owner’s Manual •••• (V 2.1) Page 3 of 26

Service barriers within this product are intended to protect the operator and service personnel from hazardous voltages. For continued safety, replace all barriers after any servicing.

This product contains safety critical parts, which if incorrectly replaced may present a risk of fire or electrical shock. Components contained within the product’s power supplies and power supply area, are not intended to be customer serviced and should be returned to the factory for repair.

To reduce the risk of fire, replacement fuses must be the same type and rating. Only use attachments/accessories specified by the manufacturer.

Environmental Information

The equipment that you purchased required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment.

To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources, Cobalt Digital encourages you to use the appropriate take-back systems. These systems will reuse or recycle most of the materials from your end-of-life equipment in an environmentally friendly and health consci ous manner.

The crossed-out wheeled bin symbol invites you to use these systems.

If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration.

You can also contact Cobalt Digital for more information on the environmental performances of our products.

Page 4 of 26 9032 Owner’s Manual •••• (V 2.1)

Contents

Introduction 6

In This Chapter..........................................................................................................................6

A Word of Thanks.....................................................................................................................6

Overview....................................................................................................................................6

Functional Block Diagram.........................................................................................................7

Supported Audio and Video Formats.........................................................................................7

Documentation Terms................................................................................................................7

Installation and Setup 8

In This Chapter..........................................................................................................................8

Static Discharge.........................................................................................................................8

Unpacking..................................................................................................................................8

Rear Module Installation (Optional) ..........................................................................................9

Rear Module Available for 9032 .............................................................................................10

Board Installation.....................................................................................................................11

Software Version.....................................................................................................................11

Card Control and Status...........................................................................................................12

Menu Structure ........................................................................................................................12

Input and Output Video...............................................................................................7

Card Status ................................................................................................................12

Menu Navigation.......................................................................................................12

Factory Default Settings............................................................................................16

Remote Control 17

In This Chapter........................................................................................................................17

DashBoard Control System Software......................................................................................17

Technical Specifications 20

Service Information 22

In This Chapter........................................................................................................................22

Troubleshooting Checklist ...................................................................................................... .22

Warranty and Repair Policy.....................................................................................................23

Ordering Information 25

9032 and Related Products......................................................................................................25

Contact Cobalt Digital Inc.......................................................................................................26

Visit us at the Cobalt Digital Inc. website................................................................................26

9032 Owner’s Manual •••• (V 2.1) Page 5 of 26

Introduction

In This Chapter

This chapter includes the following sections:

• A Word of Thanks

• Overview

• Functional Blo ck Diagram

• Supported Audio and Video Formats

• Documentation Terms

A Word of Thanks

Overview

Congratulations on choosing the openGearTM 9032 Analog to Digital Converter with Frame Sync. The 9032 is part of a full line of modular conversion gear for broadcast TV environments. The Cobalt Digital openGear distribution amplifiers, format converters, and much more. Cobalt openGear gear will meet your signal conversion needs now and well into the future.

Should you have questions pertaining to the installation or operation of your 9032, please contact us at the numbers listed on the back cover of this manual. We are happy to help with any questions regarding this or any other openGear

The 9032 is a high quality analog to digital converter that also includes a full video frame synchronizer. The product also provides full color processing control of the output video, with separate controls for

Luma Gain, Luma Lift, Chroma Saturation and Color Phase. All card configuration is done with a simple front panel menu. There is a four character text display to

view and control parameters, and a toggle switch and two buttons to navigate the menu. Card configuration can also be done over DashBoard remote control software.

The input and outputs of the 9032 are the following:

Input:

 One 3-BNC dual-rate HD/SD analog video input

Outputs:

line includes video decoders and encoders, audio embedders and de-embedders,

card.

modular conversion

 Two dual-rate HD/SD-SDI video outputs

Page 6 of 26 9032 Owner’s Manual •••• (V 2.1)

Functional Block Diagram

The 9032 has a very flexible signal flow path and feature set that combines several products into one compact package. This section diagrams the basic signal flow of your 9032 product.

HD/SD

Analog Input

Analog to Digital

Conversion

Video Proc:

Gain, Lift, Saturation, Phase

Frame

9032 Block Diagram

Figure 1. Simplified Block Di agram of 9032 Functions

Supported Audio and Video Formats

Input and Output Video

The 9032 supports the complete range of modern SMPTE standard SD and HD video formats.

Raster structure Frame Rate

1080psF 23.98, 24

1080p 23.98, 24

1080i 720p 25, 29.97, 30, 50, 59.94, 60

486i

575i

25, 29.97, 30

29.97 25

Sync

Serializer

and Cable

Driver

HD/SD SDI

Output

Notes:

1. All rates displayed as frame rates, interlaced (“i”) field rates are two times the number shown.

Documentation Terms

The following terms are used throughout this guide:

• “Frame” refers to the HPF-9000 or 8321 frame that houses the 9032 card.

• “Operator” and “User” both refer to the person who uses the 9032.

• “Board” and “Card” all refer to the 9032 card itself, including all components and

switches.

• “System” and “Video system” refers to the mix of interconnected production and

terminal equipment in which the 9032 operates.

9032 Owner’s Manual •••• (V 2.1) Page 7 of 26

Installation and Setup

In This Chapter

This chapter includes the following sections:

• Static Discharge

• Unpacking

• Rear Module Installation (Optional)

• Board Installation

• BNC Connections

• Menu Structure

• Factory Defaults

Static Discharge

Whenever handling the card and other related equipment, please observe all static discharge precautions as described in the following note:

Static discharge can cause serious damage to sensitive semiconductor devices. Avoid ha ndling circuit boards in high static environments such as carpeted areas, and when wearing

ESD

Susceptibility

synthetic fiber clothing. Always exercise proper ground ing precautions when working on circuit boards and related equipment.

Unpacking

Unpack each card you received from the shipping container, and check the contents against the packing list to ensure that all items are included. If any items are missing or damaged, contact your sales representative or Cobalt Digital directly.

Page 8 of 26 9032 Owner’s Manual •••• (V 2.1)

+ 18 hidden pages