COATS Kit 8184572 User Manual
8184575 00 11/04 1 of 2 © COPYRIGHT 2004 HENNESSY INDUSTRIES AND COATS ALL RIGHTS RESERVED PRINTED IN U.S.A.
PAX Adapter Installation
Instructions Kit 8184572
COATS, Inc. • Hennessy Industries • 1601 J.P. Hennessy Drive, LaVergne, TN 37086-3565
(800. 688-6359 • (615. 641-7533 • (615. 641-5104 FAX • www.ammcoats.com
Important: Support removal and installation steps
require two people to complete.
Removal Instructions for Left Helpers and
Support
Always disconnect the electrical power supply, air supply, and bleed the system before
servicing.
1. Disconnect the power and air supplies, and bleed
the air system.
2. Using a 10mm socket, remove the four bolts,
washers, and lock washers from the side panel and
holding the panel, remove and set aside.
3. Using a 7mm socket wrench, disconnect the lefthand support column air gauge line (fig. 1) from the
pressure limiter. Take these air hose out through the
hole in the back of the chassis.
Figure 1 - Loosen Hose Clamp to Remove Air Gauge Line
4. Remove the drop center tool from the upper lefthand helper arm and the disk tool from the lower lefthand helper arm and set aside.
5. With the aid of a person holding the helper
arm, first remove the
upper helper arm bolt and
set the upper arm aside
and then the lower helper
arm bolt and then set the
lower arm aside. (fig. 2)
Figure 2 - Remove Helper Arm Bolts
6. With the aid of a person holding the left-hand support column, start the removal of the support column
from the chassis using a 17mm socket to remove the 2
bolts holding the support column bracket to the top of
the chassis.
7. Now, remove the 3
remaining bolts holding
the support column to the
back of the chassis (fig. 3)
and then set the support
aside.
Figure 3 - Left-hand Support Column Bolt Removal
8. Using a 10mm socket, remove the inflation gauge
from the old left-hand support column and retain for
PAX adapter installation.
Note: If not already installed, it may be necessary to
replace the inflation gauge air hose with a longer 64inch hose.
PAX Adapter Installation
9. With the aid of a person holding the PAX adapter
support column, use a 17mm socket to mount the support bracket to the top of the chassis using 2 (M10x25)
bolts and 2 nuts (fig. 4) loosely installed.
Figure 4 - Install PAX Adapter Bracket
10. Next, attach the
storage tray using 3
(M10x25) bolts loosely
installed (fig. 5).
Figure 5 - Install PAX Adapter Storage Tray
Air Gauge Line
Hose Clamp
Pressure
Limiter
CAUTION
8184575 00 11/04 2 of 2 © COPYRIGHT 2004 PRINTED IN U.S.A.
11. Loosely install the PAX adapter support column
to the chassis below the storage tray using 6 (M10x25)
bolts and 6 nuts (fig. 6).
Figure 6 - Install Support Bolts Below The Storage Tray
12. Now tighten all the bolts in a star pattern adjusting tower alignment.
13. Thread the air line from the support column into
the hole on the backside of the chassis and then connect to the air manifold (fig. 7).
Figure 7 - Connect Support Air Line to Air Manifold
14. Remount the inflation gauge — attach channel to column, attach
gauge to channel, and
attach hose clamp with
hole (fig. 8).
Figure 8 - Remounted Inflation Gauge
15. Replace the side cover.
16. Bolt upper and lower arms using 10mm socket.
Configuring Machine For PAX Tire Service
Important: Always read and follow the operating manual instructions prior too servicing
your first tire. This will help prevent damage
to the tire and wheel.
17. Place the wheel riser on the table top and clamp.
Figure 9 - Riser Placed on the Table Top
18. Install the tool holder in the upper left arm and
then install the double roller system in the tool holder
with the small roller down.
Figure 10 - Install Tool Holder Then Double Roller
20. Install the tool holder in the lower left arm and
then the tapered roller.
Figure 12 - Tapered Roller installed in the Lower Left Arm Tool
Holder
CAUTION
Loading...