Page 1
EASTERN KING SIZE BED
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 7
Page 2
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1 . Remove hardware from box and sort by size.
2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to ensure fast & easy assembly.
Warning !
!
B1 ( BOX 1)
1 . Don’t attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2 . This product is for home use only and not intended for commercial establishment.
PARTS IDENTIFICATION
B2 ( BOX 2)
A
B3 ( BOX 3)
C 2 PCS.
D
E
F
G
CENTER RAIL SUPPORT WITH LEVELER
BED SLATS SUPPORT WITH LEVELER
BED RAIL
ROLL SLATS
(6 PCS.)
CENTER RAIL
1 PC.
B
2 SETS
1 PC.
4 PCS.
8 PCS.
FOOTBOARDHEADBOARD
1 PC.
H
I
J
A
CENTER RAIL END SUPPORT
FOOTBOARD SUPPORT LEG WITH LEVELER
CONCEAL PANEL
* FROM BOX 1
HEADBOARD
PAGE 2 OF 7
1 PC.
2 PCS.
2 PCS.
B
* FROM BOX 2
FOOTBOARD
Page 3
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1 . Remove hardware from box and sort by size.
2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to ensure fast & easy assembly.
Warning !
!
1 . Don’t attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2 . This product is for home use only and not intended for commercial establishment.
HARDWARE IDENTIFICATION
Z- B3 ( BOX 3) -
1
2
3
4
5
6
7
8
HARDWARE PACK IS
LOCATED IN (B3)
THREADED BOLT
WOOD DOWEL
U WASHER
SMALL FLAT WASHER
HEX NUT
WRENCH
LONG SCREW
SHORT SCREW
8 PCS.
8 PCS.
8 PCS.
8 PCS.
8 PCS.
1 PC.
24 PCS.
8 PCS.
9
10
11
12
13
LONG BOLT
SHORT BOLT
ALLEN WRENCH
LARGE FLAT WASHER
LOCK WASHER
NOTE : PHILLIPS HEAD SCREW DRIVER IS REQUIRED IN THE ASSEMBLY
PROCESS. HOWEVER, MANUFACTURER DOES NOT PROVIDE THIS ITEM.
PAGE 3 OF 7
4 PCS.
2 PCS.
1 PC.
2 PCS.
2 PCS.
Page 4
BOX 2
ASSEMBLY INSTRUCTIONS
B
STEP 1
13
10
I
12
11
STEP 1
Align & fasten footboard support leg with leveler (I) to footboard (B)
using short bolt (10), lock washer (13) & large flat washer (12) and fully tighten with Allen wrench (11).
STEP 2
STEP 2
2.1) Unscrew the pull from the back of drawer front.
2.2) Align & fasten the pull to drawer front using screw and fully tighten
with Phillips head screw driver ( NOT INCLUDED )
PAGE 4 OF 7
Page 5
BOX 1 TO BOX 3
STEP 3
3.1) Screw in threaded bolt (1) to headboard (A) leg.
3.2) Insert wood dowel (2) to the end of bed rail (C).
3.3) Align & fasten bed rail (C) to headboard (A) leg using U washer (3),
small flat washer (4) & hex nut (5) and fully tighten with wrench (6).
ASSEMBLY INSTRUCTIONS
STEP 3
1
2
A
3
4
5
C
6
O
FO TBOARD
WER BOX
DRA
STEP 4
B
3
4
1
5
2
6
STEP 4
C
4.1) Screw in threaded bolt (1) to footboard (B).
4.2) Insert wood dowel (2) to the other end of bed rail (C).
4.3) Pull out footboard (B) drawer. Align & fasten bed rail (C)
to footboard (B) using U washer (3), small flat washer (4) & hex nut (5)
and fully tighten with wrench (6).
D
STEP 5
Align & place roll slats (D) onto bed rail (C).
PAGE 5 OF 7
Page 6
STEP 6
Align & fasten center rail end support (H) to center rail (E) by
turning anti-clockwise until tight (as per diagram show).
STEP 6
ASSEMBLY INSTRUCTIONS
E
H
STEP 7
Align & fasten center rail support with leveler (F) to center rail (E) &
roll slats (D) using long bolt (9) and fully tighten with Allen wrench (11).
11
STEP 7
E
9
D
F
STEP 8
STEP 8
Align & fasten bed slats support with leveler (G)
to roll slats (D) by turning anti - clockwise until tight.
( as per diagram shown)
D
G
PAGE 6 OF 7
Page 7
STEP 9
Align & fasten roll slats (D) to bed rail (C) using long screw (7) and fully
tighten with Phillips head screw driver. (NOT INCLUDED)
STEP 9
ASSEMBLY INSTRUCTIONS
D
7
C
STEP 10
Align & fasten conceal panel (J) to
roll slats (D) using short screw (8)
and fully tighten with Phillips head
screw driver. (NOT INCLUDED)
STEP 10
8
D
J
PAGE 7 OF 7
W
Loading...