Page 1
460442(B1-B4)
REVISION 1:11/07/2013
BUNKBED
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
www.coastercompany.com
PAGE 1 OF 7
REVISION 0:11/10/2012
REVISION 2:01/21/2016
REVISION 3:04/21/2017
Page 2
ITEM :
PAGE 2 OF 7
460442 (B1-B4)
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instruction in the same sequence as numbered to assure fast & easy
assembly.
Warning!
!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact
the store immediately.
2. This product is for home use only and not intended for commercial establishment.
ASSEMBLY TIME 30 MINUTES
PARTS IDENTIFICATION
B1 (BOX 1) B3 (BOX 3)
A
RIGHT UPPER BED
END
1PC
H
LOWER BACK BED
RAIL
1PC
B
B2 (BOX 2)
C
D
B3 (BOX 3)
E
F
G
LEFT UPPER BED END
RIGHT LOWER BED
END
LEFT LOWER BED END
UPPER BACK BED
RAIL (WITH 2 HOLES)
UPPER FRONT BED
RAIL(WITH 3 HOLES)
LOWER FRONT BED
RAIL(WITH 2 HOLES)
1PC
1PC
1PC
1PC
1PC
1PC
I
J
K
L
M
N
B4 (BOX 4)
O
HARDWARE IDENTIFICATION
Z-B3(BOX 3)- HARDWARE PACK IS LOCATED IN 460442(B3)
1
LONG BOLT
22PCS
5
LONG GUARDRAIL
SHORT GUARDRAIL
RIGHT LADDER STILE
LEFT LADDER STILE
LADDER STEP
FLAT TRESTLE BAR
ROLL SLAT
(13PCS)
ALLEN CAP SCREW
2PCS
2PCS
1PC
1PC
4PCS
3PCS
2SETS
8PCS
2
3
4
NOTE: PHILLIPS HEAD SCREW DRIVER IS REQUIRED IN THE ASSEMBLY PROCESS; HOWEVER
MANUFACTURER DOES NOT PROVIDE THIS ITEM.
BARREL NUT
WOOD DOWEL
SHORT BOLT
22PCS
30PCS
12PCS
6
7
8
9
WOOD SCREW
METAL DOWEL
ALLEN WRENCH
MEDIUM BOLT
16PCS
6PCS
1PC
6PCS
www.coastercompany.com
Page 3
ITEM :
460442(B1-B4)
STEP 1 STEP 2
ASSEMBLY INSTRUCTIONS
STEP 3 STEP 4
www.coastercompany.com
PAGE 3 OF 7
Page 4
ITEM :
460442(B1-B4)
STEP 5 STEP 6
ASSEMBLY INSTRUCTIONS
STEP 7 STEP 8
www.coastercompany.com
PAGE 4 OF 7
Page 5
ITEM :
460442 (B1-B4)
STEP 9
ASSEMBLY INSTRUCTIONS
STEP 10
www.coastercompany.com
PAGE 5 OF 7
Page 6
ITEM :
460442 (B1-B4)
ASSEMBLY INSTRUCTIONS
SIZE OF MATTRESS
The length and width of the bunk mattress are as f
Length Width Thickness
74"
Upper bunk
Lower bunk 74" - 75" 37 1/2”-38 1/2” 6" maximum
Ensure thickness of mattress does not exceed 6” and
surface to top edge of guardrail.
-
75"
37 1/2"
-
ollow:
38 1/2"
6" Maximum
there must be at least 5” from mattress sleeping
1. Follow the information on the warnings appearing
carton. Do not remove the warning label from bed.
2. Always use the recommended size mattress or matt
likelihood of entrapment or falls.
3. Surface of mattress must be at least 5 in. (127
4. Do not allow children under 6 years of age to us
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrail
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving t
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a night light may provide added safety precaution for a child using upper bunk.
11. Always use guardrails on both long sides of the
to the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
12. The use of water or sleep flotation mattress is prohibited.
13. Keep these instructions for future reference.
14. Never attach or hang items to any part of the bunk bed that are not designed for use with the bed
STRANGULATION HAZARD:
for example, but not limited to hooks, belts, and j
REPLACEMENT PARTS:
Replacement parts, including additional guardrails may be obtained from any COASTER
Furniture Dealer.
SAFETY WARNING
mm) below the upper edge of guardrails.
, ladder, and other components are in their proper
upper bunk. If the bunk bed will be placed next
on the upper bunk end structure and on the
ress support or both to help prevent the
e the upper bunk.
he upper bunk.
ump ropes.
www.coastercompany.com
PAGE 6 OF 7
Page 7
ITEM :
460442 (B1-B4)
1. When using beds as bunk beds, the ladder MUST be securely
attached to the upper bunk rail at all times.
2. When using the beds as two (2) separate floor-standing beds,
the ladder MUST be stored in a separate location where children
cannot use the ladder in any manner.
ASSEMBLY INSTRUCTIONS
3. DO NOT use, nor permit children to use, the ladder in any
manner whatsoever, other than to access the top unit when
used as bunk beds, and only if the ladder is securely attached
to the top bunk rail, as set forth in the instructions.
4. Any misuse or unauthorized use of the ladder could result in
serious or fatal injury.
5. Failure to follow the above WARNING, and/or failure to follow
assembly instructions completely, will void any and all liability
of COASTER COMPANY OF AMERICA for damages and injury to
persons and property.
www.coastercompany.com | 877- COASTER (262-7838)
www.coastercompany.com
PAGE 7 OF 7
Loading...