Page 1
REVISION 0 : 03/07/2012
REVISION 1 : 06/28/2012
PAGE 1 OF 5
202311Q ( B1 & B2 )
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
www.coastercompany.com
QUEEN SIZE BED
Page 2
ITEM : ASSEMBLY INSTRUCTIONS
202311KE ( B1 & B2 )
EASTERN KING SIZE BED
A
1PC
D
FOOTBOARD
1PC
E
CENTER RAIL
1PC
B LEFT HEADBOARD LEG
1PC
F
ROLL SLAT 1 SET
(9 PCS)
C
RIGHT HEADBOARD LEG
1PC
G
2PCS
H
BED RAIL
2PCS
I
CROSS RAIL
2PCS
1PC
HB
Z - B2 (BOX 2)
1 BOLT 6PCS
5
FLAT HEAD SCREW
18PCS
2 FLAT WASHER 6PCS
6
LONG BOLT 2PCS
3 LOCK WASHER 6PCS
7
SHORT BOLT 8PCS
4 ALLEN WRENCH 1PC
8
FLAT WASHER 8PCS
9
LOCK WASHER 8PCS
10 ALLEN WRENCH 1PC
11
PAN HEAD SCREW 8PCS
www.coastercompany.com
PAGE 2 OF 5
PARTS IDENTIFICATION
HARDWARE IDENTIFICATION
Z - B1 (BOX 1)
BED SLAT SUPPORT
WITH LEVELER
202311Q (B1)
*FROM BOX 1
HEADBOARD
COMPLETE
202311Q (B1 & B2)
B1 (BOX 1)
B2 (BOX 2)
HEADBOARD
PANEL
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instruction in the same sequence as numbered to assure fast & easy assembly.
Warning!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2. This product is for home use only and not intended for commercial establishment.
Page 3
ASSEMBLY INSTRUCTIONS
202311Q (B1) - BOX 1
STEP 1 STEP 2
**BACK VIEW **BACK VIEW
202311Q (B1 & B2) - BOX 1 & BOX 2
Align and fasten the bed rails to headboard and footboard using short bolt,lock washer and flat washer and
tighten with Allen wrench.
www.coastercompany.com
PAGE 3 OF 5
IF PURCHASE HEADBOARD ONLY, SKIP BELOW STEPS
ITEM :
202311Q (B1 & B2)
Place headboard panel upside down on soft surface,
place the headboard leg on the correct position.
Align and fasten headboard leg to headboard panel
using bolt,lock washer and flat washer, and tighten with
Allen wrench.
STEP 3
STICKER 'L'
STICKER 'R'
B
C
A
1
3
2
4
Page 4
ASSEMBLY INSTRUCTIONS
STEP 4
www.coastercompany.com
PAGE 4 OF 5
ITEM :
202311Q (B1 & B2)
Align and fasten bottom cross rail (I) to bed slat support (G) using pan head screw (11) and tighten with screw
driver ( not included ) then place it into the bed.
G
11
REMARK : MAKE SURE THE BOTTOM SURFACE OF THE BED SLAT SUPPORT (G)
IS ALIGNED WIITH THE EDGE OF THE BOTTOM CROSS RAIL (I).
G
11
H
D
HB
G
I
Page 5
ASSEMBLY INSTRUCTIONS
STEP 5
www.coastercompany.com
5.1: Then fasten the bottom cross rail (I) to the bed rail (H) using pan head screw (11) and tighten with screw
driver (not included).Repeat the same process for the 2nd bed slat support.
5.3 : Align and fasten bed slat to bed rail using flat head screw (5) and tighten with screw driver (not included)
PAGE 5 OF 5
202311Q (B1 & B2)
ITEM :
5.1: Place the center rail (E) onto the bed slat support (G).Place the roll slat (F) onto the bed rail,towards the
headboards.Align and fasten the 2nd slat (F) to the center rail (E) and the 1st bed slat support (G) using long bolt
(6) and tighten with Allen wrench (10).
5
H
F
H
HB
D
H
D
HB
6
10
F
E
G
F
1st bed slat support
2nd bed slat support
Loading...