How it Works
CNET
Loading...
WNOR5305
User Manual
69 pgs1.69 Mb0

CNET WNOR5305 User Manual

Download
Page 1
1
CNet Global Technology Inc.
www.CNetusa.com
5GHz Outdoor Router
User Manual
Page 2
2
CNet Global Technology Inc.
www.CNetusa.com
Table of Contents
1.Terminology ............................................................................................................................... 4
2.Introduction ............................................................................................................................... 6
2.1 package content ................................................................................................................ 6
2.2 product features ................................................................................................................ 6
2.3 front panel description ...................................................................................................... 7
2.4 rear panel description ....................................................................................................... 8
3. Installation................................................................................................................................. 8
3.1 WNOR5305 Hardware Installation .................................................................................. 9
3.1.1 Appearance and Interface Introduction .................................................................... 9
3.1.2 Hardware installation steps .................................................................................... 11
3.2 Software Installation....................................................................................................... 11
4. Software configuration........................................................................................................... 12
4.1 Prepare your PC to configure the WLAN Broadband Router ........................................ 14
4.2 Connect to the WLAN Broadband Router ..................................................................... 15
4.3 Management and configuration on the Outdoor Router ................................................. 17
4.3.1 Wizard .................................................................................................................... 17
4.3.2 Operation Mode...................................................................................................... 24
4.3.3 Internet Settings...................................................................................................... 26
4.3.3.1 LAN ........................................................................................................... 28
4.3.3.2 VPN Passthrough ....................................................................................... 30
4.3.4 Wireless Settings .................................................................................................... 30
4.3.4.1 Basic .......................................................................................................... 31
4.3.4.2 Advanced ................................................................................................... 33
4.3.4.3 Security ...................................................................................................... 33
4.3.4.4 WPS ........................................................................................................... 40
4.3.5Administration......................................................................................................... 41
4.3.5.1 Management .............................................................................................. 41
4.3.5.2 Upload Firmware ....................................................................................... 43
4.3.5.3 Settings Management................................................................................. 44
4.3.5.4 Status.......................................................................................................... 46
4.3.5.5 System Log ................................................................................................ 46
4.4 Configuration Examples ................................................................................................. 48
4.4.1 Example one – PPPoE on the WAN ....................................................................... 48
4.4.2 Example two – fixed IP on the WAN ..................................................................... 51
4.4.3 Example three –set WLAN to be WAN as WiFi Client ......................................... 53
5. FREQUENTLY ASKED QUESTIONS (FAQ) .................................................................... 57
5.1 What and how to find my PC’s IP and MAC address?................................................... 61
5.2 What is Wireless LAN? .................................................................................................. 61
5.3 What are ISM bands? ..................................................................................................... 61
Page 3
3
CNet Global Technology Inc.
www.CNetusa.com
5.4 How does wireless networking work?............................................................................ 62
5.5 What is BSSID?.............................................................................................................. 62
5.6 What is ESSID? .............................................................................................................. 63
5.7 What are potential factors that may causes interference?............................................... 63
5.8 What are the Open System and Shared Key authentications?........................................ 63
5.9 What is WEP?................................................................................................................. 64
5.10 What is Fragment Threshold?....................................................................................... 64
5.11 What is RTS (Request to Send) Threshold? ................................................................. 65
5.12 What is Beacon Interval?.............................................................................................. 65
5.13 What is Preamble Type? ............................................................................................... 65
5.14 What is SSID Broadcast? ............................................................................................. 66
5.15 What is Wi-Fi Protected Access (WPA)? ..................................................................... 66
5.16 What is WPA2?............................................................................................................. 66
5.17 What is 802.1x Authentication?.................................................................................... 66
5.18 What is Temporal Key Integrity Protocol (TKIP)? ...................................................... 67
5.19 What is Advanced Encryption Standard (AES)? .......................................................... 67
5.20 What is Inter-Access Point Protocol (IAPP)?............................................................... 67
5.21 What is Wireless Distribution System (WDS)?............................................................ 67
5.22 What is Universal Plug and Play (uPNP)? ................................................................... 67
5.23 What is Maximum Transmission Unit (MTU) Size? ................................................... 68
5.24 What is Clone MAC Address?...................................................................................... 68
5.25 What is DDNS? ............................................................................................................ 68
5.26 What is NTP Client? ..................................................................................................... 68
5.27 What is VPN? ............................................................................................................... 68
5.28 What is IPSEC? ............................................................................................................ 68
5.29 What is WLAN Block Relay between Clients?............................................................ 69
5.30 What is WMM? ............................................................................................................ 69
5.31 What is WLAN ACK TIMEOUT? ............................................................................... 69
5.32 What is Modulation Coding Scheme (MCS)? .............................................................. 69
5.33 What is Frame Aggregation? ........................................................................................ 69
5.34 What is Guard Intervals (GI)? ...................................................................................... 69
Page 4
4
CNet Global Technology Inc.
www.CNetusa.com
1. Terminology
3DES
Triple Data Encryption Standard
AES
Advanced Encryption Standard
ANSI
American National Standards Institute
AP
Access Point
CCK
Complementary Code Keying
CSMA/CA
Carrier Sense Multiple Access/Collision Avoidance
CSMA/CD
Carrier Sense Multiple Access/Collision Detection
DDNS
Dynamic Domain Name Server
DH
Diffie-Hellman Algorithm
DHCP
Dynamic Host Configuration Protocol
DSSS
Direct Sequence Spread Spectrum
EAP
Extensible Authentication Protocol
ESP
Encapsulating Security Payload
FCC
Federal Communications Commission
FTP
File Transfer Protocol
IEEE
Institute of Electrical and Electronic Engineers
IKE
Internet Key Exchange
IP
Internet Protocol
ISM
Industrial, Scientific and Medical
LAN
Local Area Network
MAC
Media Access Control
MD5
Message Digest 5
NAT
Network Address Translation
NT
Network Termination
NTP
Network Time Protocol
PPTP
Point to Point Tunneling Protocol
PSD
Power Spectral Density
RF
Radio Frequency
SHA1
Secure Hash Algorithm
SNR
Signal to Noise Ratio
SSID
Service Set Identification
TCP
Transmission Control Protocol
TFTP
Trivial File Transfer Protocol
TKIP
Temporal Key Integrity Protocol
Page 5
5
CNet Global Technology Inc.
www.CNetusa.com
UPNP
Universal Plug and Play
VPN
Virtual Private Network
WDS
Wireless Distribution System
WEP
Wired Equivalent Privacy
WLAN
Wireless Local Area Network
WPA
Wi-Fi Protected Access
Page 6
6
CNet Global Technology Inc.
www.CNetusa.com
2.Introduction
The 5GHz WNOR5305 Outdoor Router is an affordable IEEE 802.11A/N specifications of Outdoor Router solution; setting SOHO and enterprise standard for high performance, secure, manageable and reliable WLAN. This document describes the steps required for the initial IP address assign and other configuration of the outdoor router. The description includes the implementation of the above steps.
2.1 package content
The package of the WLAN Broadband Router includes the following items,
WNOR5305 outdoor Router DC 12V Power Adapter Documentation CD POE Injector Tie
2.2 product features
Compatible with IEEE 802.11n Specifications provides wireless speed up to 150Mbps data rate. Compatible with IEEE 802.11a standard to provide wireless speeds of 54Mbps data rate. Maximizes the performance and ideal for media-centric applications like streaming video, gaming and Voice over IP
technology.
Support various operation (Bridge/Gateway/Ethernet Converter) modes between wireless and wired Ethernet inter-
faces.
Supports WPS, 64-bit and 128-bit WEP, WPA, WPA2 encryption to protect the wireless data transmission. Support TKIP/AES/TKIPAES of WPA algorithms. Support IEEE 802.3x full duplex flow control on 10/100M Ethernet interface. Support DHCP server to provide clients auto IP addresses assignment. Support DHCP client, static IP, PPPoE, L2TP and PPTP of WAN Interface. Supports firewall security with port filtering, IP filtering, MAC filtering, port forwarding, DMZ hosting and URL fil-
tering functions.
Support WEB based management and configuration. Support System Log. Support Dynamic DNS Support NTP
Page 7
7
CNet Global Technology Inc.
www.CNetusa.com
2.3 WNOR5305 front panel description
LED Indicator
State
Description
1. PWR LED ON
The WLAN Broadband Router is powered ON.
Off
The WLAN Broadband Router is powered Off.
2. WLAN LED ON
Wireless Radio ON.
Off
Wireless Radio Off.
Flashing
Data is transmitting or receiving on the wireless.
3. WAN LED ACT ON
Port linked.
Off
No link.
Flashing
Data is transmitting or receiving on the WAN interface.
4. LAN LED ACT ON
Port linked.
Off
No link.
Flashing
Data is transmitting or receiving on the LAN interface.
Page 8
8
CNet Global Technology Inc.
www.CNetusa.com
2.4 WNOR5305 rear panel description
Interfaces
Description
SMA connector
For external antenna. You can use the SMA connector to connect with 2.4GHz external an­tenna.
Secondary(Middle)
The RJ-45 sockets allow LAN connection through Category 5 cables. Support auto-sensing on 10/100M speed and half/ full duplex; comply with IEEE 802.3/ 802.3u respectively.
Main(Right)
The RJ-45 socket allows WAN connection through a Category 5 cable. Support auto-sensing on 10/100M speed and half/ full duplex; comply with IEEE 802.3/ 802.3u respectively.
Page 9
9
CNet Global Technology Inc.
www.CNetusa.com
3. Installation
3.1 WNOR5305 Hardware Installation
3.1.1 Appearance and Interface Introduction
Notes: The product shot is for reference only please refer to physical product.
1. LED Panel
2. Waterproof Sliding Door
3. Pass trough Ethernet cable from this cable
4. Push this button to remove upper housing
Page 10
10
CNet Global Technology Inc.
www.CNetusa.com
5. Wall Mount
6. Pole Mount
7. Secondary port with POE
8. Main port
9. SMA connector for external antenna
Page 11
11
CNet Global Technology Inc.
www.CNetusa.com
3.1.2 WNOR5305 hardware installation steps
Step2: Pass through Ethernet cable from the hole, insert the cable to Secondary port.
Note: RJ-45 8P8C Ethernet cable is required.
Step3: Install the upper housing and make sure the housing is well installed.
Page 12
12
CNet Global Technology Inc.
www.CNetusa.com
3.2 WNOR5305 Software Installation
Step4: Install POE Injector DC: Insert adapter POE: This hole is linked to Secondary port of the Outdoor Router with RJ-45. LAN: This hole is linked to LAN side PC/Hub or Router/ADSL modem device with RJ-45
Page 13
13
CNet Global Technology Inc.
www.CNetusa.com
Step5: Complete the hardware installation as diagram at below
Notes: Use Reset button on POE injector. Push continually the reset button of POE injector about 5 ~10 seconds to reset
the configuration parameters to factory defaults.
There is no software driver or utility installation needed, but only the configuration setting. Please re­fer to chapter 4 for software configuration.
Notice: It will take about 50 seconds to complete the boot up sequence after powered on the Outdoor Router; Power LED
will be active, and after that the WLAN Activity LED will be flashing to show the WLAN interface is enabled and working now.
Page 14
14
CNet Global Technology Inc.
www.CNetusa.com
4. Software configuration
There are web based management and configuration functions allowing you to have the jobs done easily. The Outdoor Router is delivered with the following factory default parameters on the Ethernet LAN interfaces. Default IP Address: 192.168.1.1 Default IP subnet mask: 255.255.255.0 WEB login User Name: admin WEB login Password: admin Telnet login User Name: admin Telnet login Password: admin
Page 15
15
CNet Global Technology Inc.
www.CNetusa.com
4.1 Prepare your PC to configure the WLAN Broadband Router
For OS of Microsoft Windows 2000/ XP:
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
2. Move mouse and double-click the right button on Network and Dial-up Connections icon. Move mouse and double-click the Local Area Connection icon. The Local Area Connection window will appear. Click Properties button in the Local Ar- ea Connection window.
3. Check the installed list of Network Components. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6.
4. Select Protocol in the Network Component Type dialog box and click Add button.
5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation.
6. Select TCP/IP and click the properties button on the Network dialog box.
7. Select Specify an IP address and type in values as following example.
IP Address: 192.168.1.2, any IP address within 192.168.1.2 to 192.168.1.254 is good to connect the Wireless LAN Access Point. Don’t use 192.168.1.1.
IP Subnet Mask: 255.255.255.0
8. Click OK to complete the IP parameters setting.
For OS of Microsoft Windows Vista / 7:
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
2. Move mouse and double-click the right button on Network Connections item. The Network Connections window will appear. Double click Local Area Connection icon, then User Account Control window shown. Right click Continue button to set properties.
3. In Local Area Connection Properties window, Choose Networking tab, move mouse and click Internet Protocol Version 4 (TCP/IPv4), then click Properties button.
4. Move mouse and click General tab, Select Specify an IP address and type in values as following example.
IP Address: 192.168.1.2, any IP address within 192.168.1.2 to 192.168.1.254 is good to connect the Wireless LAN Access Point. Don’t us e 192.168.1.1.
IP Subnet Mask: 255.255.255.0
5. Click OK to complete the IP parameters setting.
For OS of Microsoft Windows NT:
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
2. Move mouse and double-click the right button on Network icon. The Network window will appear. Click Protocol tab from the Network window.
3. Check the installed list of Network Protocol window. If TCP/IP is not installed, click the Add button to install it; other­wise go to step 6.
4. Select Protocol in the Network Component Type dialog box and click Add button.
5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it
Page 16
16
CNet Global Technology Inc.
www.CNetusa.com
may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation.
6. Select TCP/IP and click the properties button on the Network dialog box.
7. Select Specify an IP address and type in values as following example.
IP Address: 192.168.1.2, any IP address within 192.168.1.2 to 192.168.1.254 is good to connect the Wireless LAN Access Point. Don’t us e 192.168.1.1.
IP Subnet Mask: 255.255.255.0
8. Click OK to complete the IP parameters setting.
Page 17
17
CNet Global Technology Inc.
www.CNetusa.com
4.2 Connect to the WLAN Broadband Router
Open a WEB browser, i.e. Microsoft Internet Explorer 6.1 SP1 or above, then enter 192.168.1.1 on the URL to connect the WLAN Broadband Router.
4.3 Management and configuration on the Outdoor Router
4.3.1 Wizard
This Wizard page guides you to configure Internet connection and Wireless Settings quickly.
Step 1: Configure Internet connection
Click Next button to the next step for Internet connection settings. There are five options (DHCP, Static Mode, PPPOE, L2TP, PPTP) for Internet connection on WAN port.
a. DHCP (Auto Configure)
Page 18
18
CNet Global Technology Inc.
www.CNetusa.com
If you select DHCP option, please click Next button to jump at Step2.
b. Static Mode (fixed IP)
If you select Static Mode (fixed IP), please fill in these fields on next page.
Item
Description
IP Address
Fill in the IP address for WAN interface.
Subnet Mask
Fill in the subnet mask for WAN interface.
Default Gateway
Fill in the default gateway for WAN interface out going data packets.
Primary DNS Server
Fill in the IP address of Domain Name Server 1.
Secondary DNS Server
Fill in the IP address of Domain Name Server 2.
When you finish these settings, then click Next button to jump at Step2.
Page 19
19
CNet Global Technology Inc.
www.CNetusa.com
c. PPPOE Connection
If you select PPPOE, please fill in these fields on next page.
Item
Description
User Name
If you select the PPPoE support on WAN interface, fill in the user name and password to login the PPPoE server.
Password
If you select the PPPoE support on WAN interface, fill in the user name and password to login the PPPoE server.
Verify Password
Fill in the password again for verification.
Operation Mode
Keep Alive: Keep the PPPoE connection all the time. Please also configure the Redial Period field. On Demand: Please configure the Idle Time field. When time is up, the PPPoE connection will
disconnect. The connection will re-connect when any outgoing packet arise. Manual: Let user con- nect the PPPoE connection manually.
When you finish these settings, then click Next button to jump at Step2.
Page 20
20
CNet Global Technology Inc.
www.CNetusa.com
d. L2TP
If you select L2TP, please fill in these fields on next page.
Item
Description
L2TP Server IP Address
Allow user to make a tunnel with remote site directly to secure the data transmission among the connection. User can use embedded L2TP client supported by this router to make a VPN connection. If you select the L2TP support on WAN interface, fill in the IP address for it.
User Name
Fill in the user name and password to login the L2TP server.
Password
Fill in the user name and password to login the L2TP server.
Address Mode
Static: To configure the IP address information by manually, please fill in the related setting at be­low. Dynamic: The option allows the machine to get IP address information automatically from DHCP server on WAN side.
IP Address
Fill in the IP address for WAN interface.
Subnet Mask
Fill in the subnet mask for WAN interface.
Default Gateway
Fill in the default gateway for WAN interface out going data packets.
Page 21
21
CNet Global Technology Inc.
www.CNetusa.com
Operation Mode
Keep Alive: Keep the L2TP connection all the time. Please also configure the Redial Period field. Manual: Let user connect the L2TP connection manually.
When you finish these settings, then click Next button to jump at Step2.
Page 22
22
CNet Global Technology Inc.
www.CNetusa.com
e. PPTP
If you select PPTP, please fill in these fields on next page.
Item Description
Item
Description
PPTP Server IP Address
Allow user to make a tunnel with remote site directly to secure the data transmission among the connection. User can use embedded PPTP client supported by this router to make a VPN connec tion. If you select the PPTP support on WAN interface, fill in the IP address for it.
User Name
Fill in the user name and password to login the PPTP server.
Password
Fill in the user name and password to login the PPTP server.
Address Mode
Static: To configure the IP address information by manually, please fill in the related setting at be­low. Dynamic: The option allows the machine to get IP address information automatically from DHCP server on WAN side.
IP Address
Fill in the IP address for WAN interface.
Subnet Mask
Fill in the subnet mask for WAN interface.
Default Gateway
Fill in the default gateway for WAN interface out going data packets.
Operation Mode
Keep Alive: Keep the PPTP connection all the time. Please also configure the Redial Period field. Manual: Let user connect the PPTP connection manually.
Page 23
23
CNet Global Technology Inc.
www.CNetusa.com
Step 2: Configure Wireless Settings
There are three options (Disable, WEP, WPA-PSK/WPA2-PSK) for Wireless security connection.
Disable
OPENWEP
Page 24
24
CNet Global Technology Inc.
www.CNetusa.com
SHAREDWEP
WPA-PSK
Page 25
25
CNet Global Technology Inc.
www.CNetusa.com
WPA2-PSK
Item
Description
Wireless Mode
Click to select wireless mode from pull down menu.
Frequency (Channel)
Select the wireless communication frequency/channel from pull-down menu.
Network Name (SSID)
It is the wireless network name. The SSID can be 32 bytes long.
Channel Bandwidth
Select the operating channel width 20 MHz or 20/40 MHz.
Security
Please select the security mode related wireless data encryption.
KEY
WEP: When you select WEP, please input 5, 13 (ASCII), 10 or 26 (HEX) characters for WEP Key. WPA-PSK/WPA2-PSK: When WPA/WPA2 Pre-shared key encryption is selected, please fill in the Pre-shared key. The format can be passphrase or Hex (64 characters).
When you finish these settings, then click Apply button to save.
Page 26
26
CNet Global Technology Inc.
www.CNetusa.com
4.3.2 Operation Mode
a. Bridge:
In Bridge mode, all ethernet ports and wireless interfaces are bridged together and NAT function
is disabled. All the WAN related function and firmware all not supported.
b. Gateway:
In Gateway mode, the device is supposed to connect to internet via ADSL/Cable modem. The NAT is enabled and PCs in LAN ports shard the same IP to ISP through WAN port. The connection type can be setup in WAN page by using PPPOE, DHCP client, PPTP client, L2TP client or static IP.
Page 27
27
CNet Global Technology Inc.
www.CNetusa.com
c. Wireless ISP
In Wireless ISP mode, all ethernet ports are bridged together and the wireless client will connect to ISP access point. The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN. You must set the wireless to client mode first and connect to the ISP AP in Site-Survey page.
Page 28
28
CNet Global Technology Inc.
www.CNetusa.com
.4.3.3 Internet Settings
4.3.3.1 LAN
Item
Description
MAC Address
This shows the MAC address of the device.
IP Address
Fill in the IP address for LAN interface.
Subnet Mask
Fill in the subnet mask for LAN interface.
DHCP Type
Disable: Disable DHCP server on LAN side. Server: Enable DHCP server on LAN side.
Start IP Address
You can configure the first IP from the DHCP Server.
Page 29
29
CNet Global Technology Inc.
www.CNetusa.com
End IP Address
You can configure the last IP from the DHCP Server.
Lease Time
Fill in the lease time of DHCP server function.
LLTD
Select enable or disable the Link Layer Topology Discover function from pull-down menu.
IGMP Proxy
Select enable or disable the IGMP proxy function from pull-down menu.
UPNP
Select enable or disable the UPnP protocol from pull-down menu.
Router Adver­tisement
Select enable or disable the Router Advertisement protocol from pull-down menu. PPPoE Relay
Select enable or disable the PPPoE Relay function from pull-down menu.
DNS Proxy
Select enable or disable the DNS Proxy function from pull-down menu.
Page 30
30
CNet Global Technology Inc.
www.CNetusa.com
4.3.3.3 VPN Pass through
Item
Description
L2TP Pass through
Select enable or disable the L2TP pass -through function from pull-down menu.
IPSec Pass through
Select enable or disable the IPSec pass -through function from pull-down menu.
PPTP Pass through
Select enable or disable the PPTP pass-through function from pull-down menu.
Page 31
31
CNet Global Technology Inc.
www.CNetusa.com
4.3.4 Wireless Settings
4.3.4.1 Basic
Page 32
32
CNet Global Technology Inc.
www.CNetusa.com
Item
Description
Wireless On/Off
Click Wireless OFF button to turn off wireless RF radio. Click Wireless ON button to turn on wire­less RF radio.
Antenna Switch
Select Internal antenna or External antenna for using. The default is using Internal antenna.
Wireless Mode
Click to select wireless mode from pull down menu.
Wireless Band
Click to select wireless band from pull down menu.
SSID
It is the wireless network name. The SSID can be 32 bytes long. User can use the default SSID or change it.
Broadcast Net­work Name (SSID)
Enable or disable the SSID broadcast function.
AP Isolation
Wireless network is similar to the virtual local area network. All of the Wireless client devices can access each other completely. When you enable this function, it will turn off connection between wireless clients. Only allows connection between wireless client and this AP router.
MBSSID AP Isolation
Enable this function will turn off connection between clients with different MBSSID. Example: The client connected with BSSID 1. When enable this function, it will not connect with BSSID 2. Only can access between clients with SSID 1.
BSSID
Show the MAC address of Wireless interface.
Frequency (Channel)
Select the wireless communication frequency/channel from pull-down menu. Operating Mode
Select “Mixed Mode” for 11a/n mode or “Green Field” for 11n mode.
Channel Band­width
Select the operating channel width 20 MHz or 20/40 MHz.
Guard Interval
Select “Long” or “Auto”. Guard intervals are us ed to ensure that distinct trans missions do not inte r­fere with one another. Only effect under Mixed Mode.
MCS
Select 0~7 or “Auto” from pull down menu. The default is “Auto”. Only effect under Mixed Mode.
Page 33
33
CNet Global Technology Inc.
www.CNetusa.com
4.3.4.2 Advanced
Item
Description
Beacon Interval
Beacons are the packets sending by Access point to synchronize the wireless network. The beacon interval is the time interval between beacons sending by this unit in AP or AP+WDS operation. The default and recommended beacon interval is 100 milliseconds.
Data Beacon Rate(DTM)
This is the Delivery Traffic Indication Map. It is used to alert the clients that multicast and broadcast packets buffered at the AP will be transmitted immediately after the transmission of this beacon frame. You can change the value from 1 to 255. The AP will check the buffered data according to this value. For example, selecting “1” means to check the buffered data at every beacon.
Fragment Threshold
The fragmentation threshold determines the size at which packets are fragmented (sent as several pieces instead of as one block). Use a low setting in areas where communication is poor or where there is a great deal of radio interference. This function will help you to improve the network per­formance.
Page 34
34
CNet Global Technology Inc.
www.CNetusa.com
RTS Threshold
The RTS threshold determines the packet size at which the radio issues a request to send (RTS) b e­fore sending the packet. A low RTS Threshold setting can be useful in areas where many client de­vices are associating with the device, or in areas where the clients are far apart and can detect only the device and not each other. You can enter a setting ranging from 0 to 2347 bytes.
TX Power
The default TX power is 100%. In case of shortening the distance and the coverage of the wireless network, input a smaller value to reduce the radio transmission power. For example, input 80 to ap­ply 80% Tx power.
Short Preamble
Default: Disable. It is a performance parameter for 802.11 b/g mode and not supported by some of very early stage of 802.11b station cards. If there is no such kind of stations associated to this AP, you can enable this function.
Short Slot
It is used to shorten the communication time between this AP and station.
TX Burst
The device will try to send a serial of packages with single ACK reply from the clients. Enable this function to apply it.
Country Code
Select the country code for wireless from pull down menu.
Page 35
35
CNet Global Technology Inc.
www.CNetusa.com
3.4.3.4.3 Security
a. Disable
If you set Security Mode to “Disable”, the wireless data transmission will not include encryption to prevent from unauthorized access and monitoring.
b. OPENWEP
Page 36
36
CNet Global Technology Inc.
www.CNetusa.com
If you set Security Mode to “OPENWEP”, please fill in the related configurations below.
Item
Description
Default Key
Specify a Key number for effective.
WEP Keys (1~4)
Please input 5, 13 (ASCII), 10 or 26 (HEX) characters for WEP Key.
Page 37
37
CNet Global Technology Inc.
www.CNetusa.com
c. WPA-PSK/WPA2-PSK/WPAPSKWPA2PSK
Page 38
38
CNet Global Technology Inc.
www.CNetusa.com
If you set Security Mode to “WPA-PSK , WPA2-PSK or WPAPSKWPA2PSK”, please fill in the related configurations below.
Item
Description
WPA Algo­rithms
Select TKIP, AES, or TKIPAES for WPA algorithms.
Pre-Shared Key
Please fill in the key like ‘12345678’.
Key Renewal Interval
Please fill in a number for Group Key Renewal interval time.
Page 39
39
CNet Global Technology Inc.
www.CNetusa.com
d. Access Policy
Item
Description
Policy
Select the Disabled, Allow or Reject of drop down menu choose wireless access control mode. This is a security control function; only those clients registered in the access control list can link to this WLAN Broadband Router.
Add a station MAC
Fill in the MAC address of client to register this AP router access capability.
Page 40
40
CNet Global Technology Inc.
www.CNetusa.com
4.3.4.4 WPS
Item
Description
WPS
Select Enabled or Disabled the Wi-Fi Protected Setup function. Then click Apply button to take ef- fect function.
WPS Summary
After enabling the WPS function, if there is connection the WPS Summary will show related infor­mation and status.
AP PIN
Here shows the AP’s PIN code (Personal Identification Number) that the enrollee should enter the
registrar’s PIN code to make a connection. Click Generate button to generate a new AP PIN code.
Reset OOB
Click Reset OOB button to reset WPS AP to the OOB (out-of-box) configuration.
WPS mode
Select WPS mode. PIN: Personal Identification Number. PBC: Push Button Communication.
PIN
Input enrollee’s PIN code to AP-registrar.
Page 41
41
CNet Global Technology Inc.
www.CNetusa.com
4.3.5Administration
4.3.5.1 Management
Item
Description
Username
Fill in the user name for web management login control.
Password
Fill in the password for web management login control.
Current Time
It shows the current time.
Time Zone
Select the time zone in your country from pull-down menu..
NTP Server
Fill in NTP server IP address.
NTP synchronization
Fill in a number to decide the synchronization frequency with NTP server.
Page 42
42
CNet Global Technology Inc.
www.CNetusa.com
Item
Description
Dynamic DNS Provider
Click the drop down menu to pick up the right DDNS provider you registered.
Account
Fill in the account of DDNS you registered.
Password
Fill in the password of DDNS you registered.
DDNS
Fill in the domain name that you registered.
Page 43
43
CNet Global Technology Inc.
www.CNetusa.com
4.3.5.2 Qos
Item
Description
Uplink Speed
Input uplink Maximum upload speed
Downlink Speed
Input downlink Maximum upload speed
Local IP Address
Fill in the local IP address
Uplink Bandwidth
Fill limit upload bandwidth
Downlink Bandwidth
Fill limit downlink bandwidth
Page 44
44
CNet Global Technology Inc.
www.CNetusa.com
4.3.5.3 Upload Firmware
Item
Description
Location
Click the Browse button to select the new firmware image file on PC. And click the Apply button to upgrade firmware.
Page 45
45
CNet Global Technology Inc.
www.CNetusa.com
4.3.5.4 Settings Management
Item
Description
Export Button
Click Export button to export the current configuration to your PC.
Settings file location
Click Browse button to select the configuration file from your PC, then click Import button to update the configuration.
Load Default Button
Click the Load Default button to reset the configuration parameter to factory defaults.
Page 46
46
CNet Global Technology Inc.
www.CNetusa.com
4.3.6.5 Status
This page shows the current status and some basic settings of the device, including System Information, Wireless Infor­mation, WAN Information and LAN Information.
Page 47
47
CNet Global Technology Inc.
www.CNetusa.com
4.3.6.6 System Log
This page is used to view system logs
Item
Description
Refresh
Click the Refresh button to refresh the log shown on the screen.
Clear
Click the Clear button to clear the log display screen.
Page 48
48
CNet Global Technology Inc.
www.CNetusa.com
4.4 Configuration Examples
4.4.1 Example one – PPPoE on the WAN
Sales division of Company ABC likes to establish a WLAN network to support mobile communication on sales’ Notebook PCs. MIS engineer collects information and plans the WLAN Broadband Router implementation by the following configu­ration.
WAN configuration: PPPoE
User Name
User123
Password
Password123
Note: User Name and Password that ISP provided
LAN configuration:
IP Address
192.168.1.254
Subnet Mask
255.255.255.0
DHCP Client Range
192.168.1.100 –192.168.1.200
WLAN configuration:
SSID
AP
Channel Number
AutoSelect
Page 49
49
CNet Global Technology Inc.
www.CNetusa.com
1. Configure the Operati on Mode Confi guration
Open “Operation Mode Confi gurati on ” page, select Gateway. Press “Apply” button to confirm the configuration setting.
Page 50
50
CNet Global Technology Inc.
www.CNetusa.com
2. Configure the WAN interface:
Open “W ide Area Network (WAN) Settings” page, select PPPoE then enter the User Name “User123” and Pass word “Pass word123”, the pas s word is encrypted to display on the screen. Press “Apply” button to confirm the configuration setting.
Page 51
51
CNet Global Technology Inc.
www.CNetusa.com
3. Configure the WLAN interface:
Open “Basic Wireless Settings ” page, enter the SSID ”AP”, Channel Number ”AutoSelect”. Press “Apply” button to confirm the configuration setting.
Page 52
52
CNet Global Technology Inc.
www.CNetusa.com
4. Configure the LAN interface:
Open “Local Area Network (LAN) settings ” page, and enter the IP Address “192.168.1.254”, Subnet Mas k “255.255.255.0”. Enable DHCP Server, DHCP client range “192.168.1.100” to “192.168.1.200”, default Gateway “192.168.1.254” . Press “Apply” button to confirm the configuration setting
Page 53
53
CNet Global Technology Inc.
www.CNetusa.com
4.4.2 Example two – Fixed IP on the WAN
Company ABC likes to establish a WLAN network to support mobile communication on all employees ’ Notebook PCs. MIS engineer collects information and plans the WLAN Broadband Router implementation by the following configuration.
WAN configuration : Fixed IP
IP Address
10.10.10.10
Subnet Mask
255.255.255.0
Default Gateway
10.10.10.1
Primary DNS Address
168.95.1.1
LAN configuration:
IP Address
192.168.1.254
Subnet Mask
255.255.255.0
DHCP Client Range
192.168.1.50 – 192.168.1.150
WLAN configuration:
SSID
WNOR5305_CNet
Channel Number
AutoSelect
Page 54
54
CNet Global Technology Inc.
www.CNetusa.com
1. Configure the WAN interface:
Open “W ide Area Network (WAN) Settings” page, select STATIC (fixed IP) and enter IP Address “10.10.10.10” , subnet mas k “255.255.255.0”, Default gateway “10.10.10.1”. Press “Apply” button to confirm the configuration setting.
Page 55
55
CNet Global Technology Inc.
www.CNetusa.com
2. Configure the LAN interface:
Open “Local Area Network (LAN) settings ” page, and enter the IP Address “192.168.1.254”, Subnet Mas k “255.255.255.0”. Enable DHCP Server, DHCP client range “192.168.1.50” to “192.168.1.150”, default Gateway “192.168.1.254” . Press “Apply” button to confirm the configuration setting
.
Page 56
56
CNet Global Technology Inc.
www.CNetusa.com
3. Configure the WLAN interface:
Open “Basic Wireless Settings ” page, and enter the SSID ”WNOR5305_CNet”, Channel Number ”Auto Select”. Press “Apply” button to confirm the configuration setting.
Page 57
57
CNet Global Technology Inc.
www.CNetusa.com
4.4.3 Example three –Set WLAN to be WAN as WiFi Client
User Mr. ABC likes to configure this WLAN Broadband Router to be a WiFi client. In order to communicate with another AP, Mr. ABC collects information and plans the WLAN Broadband Router implementation by the following configuration.
WiFi client: WAN configuration: DHCP (Auto config.)
IP Address
n/a
Subnet Mask
n/a
Default Gateway
n/a
Primary DNS Address
n/a
LAN configuration:
IP Address
192.168.1.254
Subnet Mask
255.255.255.0
DHCP Client Range
192.168.1.100 –192.168.1.200
WLAN configuration:
SSID
802.11an_Router
Channel Number
Channel 36
WiFi server:
AP configuration:
SSID
TestAP
Channel Number
Channel 36
Wireless Encryption
n/a
DHCP server
192.168.88.2~192.168.88.200
Page 58
58
CNet Global Technology Inc.
www.CNetusa.com
1. Configure the Operation Mode: Open “Operation Mode Configuration” page, select Wireless ISP, and click “Apply” button to confirm the configuration
setting and then reboot the WLAN Broadband Router. After reboot, the wireless LAN will become WAN interface.
2. Site Survey:
Open “Site Survey” page under Wireless Settings, and s elect the AP “TestAP”. Press “Next” button to connect with the AP.
Page 59
59
CNet Global Technology Inc.
www.CNetusa.com
3. Wireless encryption setting: If the AP has encryption setting, it will pop out a window for you to fill in the encryption setting. Please fill up the encryption code and click “Apply” button to connect with the AP.
Page 60
60
CNet Global Technology Inc.
www.CNetusa.com
4 Status: You can open “Status ” page under Administration to check Internet Configurations.
Page 61
61
CNet Global Technology Inc.
www.CNetusa.com
5. FREQUENTLY ASKED QUESTIONS (FAQ)
5.1 What and how to find my PC’s IP and MAC address?
5.1 What and how to find my PC’s IP and MAC address?
IP address is the identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route mes­sages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be zero to 255. For example, 191.168.1.254 could be an IP address The MAC (Media Access Control) address is your computer's unique hardware number. (On an Ethernet LAN, it's the same as your Ethernet address.) When you're connected to the Internet from your computer (or host as the Internet protocol thinks of it), a correspondence table relates your IP address to your computer's physical (MAC) address on the LAN. To find your PC’s IP and MAC address,
Open the Command program in the Microsoft Windows. Type in “ipconfig /all”, then press the Enter button. Your PC’s IP address is the one entitled IP Address and your PC’s MAC addres s is the one entitled Physical Address.
5.2 What is Wireless LAN?
A wireless LAN (WLAN) is a network that allows access to Internet without the need for any wired connections to the us­er’s machine.
5.3 What are ISM bands?
ISM stands for Industrial, Scientific and Medical; radio frequency bands that the Federal Communications Commission (FCC) authorized for wireless LANs. The ISM bands are located at 915 +/-13 MHz, 2450 +/-50 MHz and 5800 +/-75 MHz.
Page 62
62
CNet Global Technology Inc.
www.CNetusa.com
5.4 How does wireless networking work?
The 802.11 standard define two modes: infrastructure mode and ad hoc mode. In infrastructure mode, the wireless network consists of at least one access point connected to the wired network infrastructure and a set of wireless end stations. This configuration is called a Basic Service Set (BSS). An Extended Service Set (ESS) is a set of two or more BSSs forming a single sub-network. Since most corporate WLANs require access to the wired LAN for services (file servers, printers, In­ternet links) they will operate in infrastructure mode. Example
example 1: wireless Infrastructure Mode Ad hoc mode (also called peer-to-peer mode or an Independent Basic Service Set, or IBSS) is simply a set of 802.11 wire­less stations that communicate directly with one another without using an access point or any connection to a wired net­work. This mode is useful for quickly and easily setting up a wireless network anywhere that a wireless infrastructure does not exist or is not required for services, such as a hotel room, convention center, or airport, or where access to the wired network is barred (such as for consultants at a client site).
Example 2: wireless Ad Hoc Mode
Page 63
63
CNet Global Technology Inc.
www.CNetusa.com
5.5 What is BSSID?
A six-byte address is that distinguish a particular a particular access point from others. Also know as just SSID. Serve as a network ID or name.
5.6 What is ESSID?
The Extended Service Set ID (ESSID) is the name of the network you want to access. It is used to identify different wire­less networks.
5.7 What are potential factors that may causes interference?
Factors of interference:
Obstacles: walls, ceilings , furniture… etc. Building Materials: metal door, aluminum studs. Electrical devices: microwaves, monitors and electrical motors.
Solutions to overcome the interferences:
Minimizing the number of walls and ceilings. Position the WLAN antenna for best reception. Keep WLAN devices away from other electrical devices: microwaves, monitors, electric motors…etc. Add additional WLAN Access Points if necessary.
5.8 What are the Open System and Shared Key authentications?
IEEE 802.11 supports two subtypes of network authentication services: open system and shared key. Under open system authentication, any wireless station can request authentication. The station that needs to authenticate with another wireless station sends an authentication management frame that contains the identity of the sending station. The receiving station then returns a frame that indicates whether it recognizes the sending station. Under shared key au­thentication, each wireless station is assumed to have received a secret shared key over a secure channel that is independent from the 802.11 wireless network communications channel.
Page 64
64
CNet Global Technology Inc.
www.CNetusa.com
5.9 What is WEP?
An option of IEEE 802.11 function is that offers frame transmission privacy similar to a wired network. The Wired Equivalent Privacy generates secret shared encryption keys that both source and destination stations can use to alert frame bits to avoid disclosure to eavesdroppers. WEP relies on a secret key that is shared between a mobile station (e.g. a laptop with a wireless Ethernet card) and an ac­cess point (i.e. a base station). The secret key is used to encrypt packets before they are transmitted, and an integrity check is used to ensure that packets are not modified in transit.
5.10 What is Fragment Threshold?
The proposed protocol uses the frame fragmentation mechanism defined in IEEE 802.11 to achieve parallel transmissions. A large data frame is fragmented into several fragments each of size equal to fragment threshold. By tuning the fragment threshold value, we can get varying fragment sizes. The determination of an efficient fragment threshold is an important issue in this scheme. If the fragment threshold is small; the overlap part of the master and parallel transmissions is large. This means the spatial reuse ratio of parallel transmissions is high. In contrast, with a large fragment threshold, the overlap is small and the spatial reuse ratio is low. However high fragment threshold leads to low fragment overhead. Hence there is a trade-off between spatial re-use and fragment overhead. Fragment threshold is the maximum packet size used for fragmentation. Packets larger than the size programmed in this field will be fragmented. If you find that your corrupted packets or asymmetric packet reception (all send packets, for example). You may want to try lowering your fragmentation threshold. This will cause packets to be broken into smaller fragments. These small fragments, if corrupted, can be resent faster than a larger fragment. Fragmentation increases overhead, so you'll want to keep this value as close to the maximum value as possible.
Page 65
65
CNet Global Technology Inc.
www.CNetusa.com
5.11 What is RTS (Request to Send) Threshold?
The RTS threshold is the packet size at which packet transmission is governed by the RTS/CTS transaction. The IEEE
802.11-1997 standard allows for short packets to be transmitted without RTS/ CTS transactions. Each station can have a different RTS threshold. RTS/CTS is used when the data packet size exceeds the defined RTS threshold. With the CSMA/CA transmission mechanism, the transmitting station sends out an RTS packet to the receiving station, and waits for the receiving station to send back a CTS (Clear to Send) packet before sending the actu­al packet data. This setting is useful for networks with many clients. With many clients, and a high network load, there will be many more collisions. By lowering the RTS threshold, there may be fewer collisions, and performance should improve. Basically, with a faster RTS threshold, the system can recover from problems faster. RTS packets consume valuable bandwidth, however, so setting this value too low will limit performance.
5.12 What is Beacon Interval?
In addition to data frames that carry information from higher layers, 802.11 include management and control frames that support data transfer. The beacon frame, which is a type of management frame, provides the "heartbeat" of a wireless LAN, enabling stations to establish and maintain communications in an orderly fashion. Beacon Interval represents the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon (and learn whether there are buffered frames at the access point).
5.13 What is Preamble Type?
There are two preamble types defined in IEEE 802.11 specification. A long preamble basically gives the decoder more time to process the preamble. All 802.11 devices support a long preamble. The short preamble is designed to improve efficiency (for example, for VoIP systems). The difference between the two is in the Synchronization field. The long preamble is 128 bits, and the short is 56 bit
Page 66
66
CNet Global Technology Inc.
www.CNetusa.com
5.14 What is SSID Broadcast?
Broadcast of SSID is done in access points by the beacon. This announces your access point (including various bits of in­formation about it) to the wireless world around it. By disabling that feature, the SSID configured in the client must match the SSID of the access point. Some wireless devices don't work properly if SSID isn't broadcast (for example the D-link DWL-120 USB 802.11b adapt­er). Generally if your client hardware s upports operation with SSID disabled, it’s not a bad idea to run that way to enhance network security. However it's no replacement for WEP, MAC filtering or other protections.
5.15 What is Wi-Fi Protected Access (WPA)?
Wi-Fi’s original security mechanism, Wired Equivalent Privacy (WEP), has been viewed as insufficient for securing con- fidential business communications. A longer-term solution, the IEEE 802.11i standard, is under development. However, since the IEEE 802.11i standard is not expected to be published until the end of 2003, several members of the Wi-Fi Alli­ance teamed up with members of the IEEE 802.11i task group to develop a significant near-term enhancement to Wi-Fi se­curity. Together, this team developed Wi-Fi Protected Access. To upgrade a WLAN network to support WPA, Access Points will require a WPA software upgrade. Clients will require a software upgrade for the network interface card, and possibly a software update for the operating system. For enterprise networks, an authentication server, typically one that supports RADIUS and the selected EAP authentication protocol will be added to the network.
5.16 What is WPA2?
It is the second generation of WPA. WPA2 is based on the final IEEE 802.11i amendment to the 802.11 standard.
5.17 What is 802.1x Authentication?
802.1x is a framework for authenticated MAC-level access control, defines Extensible Authentication Protocol (EAP) over LANs (WAPOL). The standard encapsulates and leverages much of EAP, which was defined for dial-up authentication with Point-to-Point Protocol in RFC 2284. Beyond encapsulating EAP packets, the 802.1x standard also defines EAPOL messages that convey the shared key infor­mation critical for wireless security.
Page 67
67
CNet Global Technology Inc.
www.CNetusa.com
5.18 What is Temporal Key Integrity Protocol (TKIP)?
The Temporal Key Integrity Protocol, pronounced tee-kip, is part of the IEEE 802.11i encryption standard for wireless LANs. TKIP is the next generation of WEP, the Wired Equivalency Protocol, which is used to secure 802.11 wireless LANs. TKIP provides per-packet key mixing, a message integrity check and a re-keying mechanism, thus fixing the flaws of WEP.
5.19 What is Advanced Encryption Standard (AES)?
Security issues are a major concern for wireless LANs, AES is the U.S. government’s next -generation cryptography algo­rithm, which will replace DES and 3DES.
5.20 What is Inter-Access Point Protocol (IAPP)?
The IEEE 802.11f Inter-Access Point Protocol (IAPP) supports Access Point Vendor interoperability, enabling roaming of
802.11 Stations within IP subnet. IAPP defines messages and data to be exchanged between Access Points and between the IAPP and high layer management entities to support roaming. The IAPP protocol uses TCP for inter-Access Point communication and UDP for RADIUS re­quest/response exchanges. It also uses Layer 2 frames to update the forwarding tables of Layer 2 devices.
5.21 What is Wireless Distribution System (WDS)?
The Wireless Distribution System feature allows WLAN AP to talk directly to other APs via wireless channel, like the wireless bridge or repeater service.
5.22 What is Universal Plug and Play (uPNP)?
UPnP is an open networking architecture that consists of services, devices, and control points. Theultimate goal is to allow data communication among all UPnP devices regardless of media, operating system, programming language, and wired/wireless connection.
Page 68
68
CNet Global Technology Inc.
www.CNetusa.com
5.23 What is Maximum Transmission Unit (MTU) Size?
Maximum Transmission Unit (MTU) indicates the network stack of any packet is larger than this value will be fragmented before the transmission. During the PPP negotiation, the peer of the PPP connection will indicate its MRU and will be ac­cepted. The actual MTU of the PPP connection will be set to the smaller one of MTU and the peer’s MRU.
5.24 What is Clone MAC Address?
Clone MAC address is designed for your special application that request the clients to register to a server machine with one identified MAC address. Since that all the clients will communicate outside world through the WLAN Broadband Router, so have the cloned MAC address set on the WLAN Broadband Router will solve the issue.
5.25 What is DDNS?
DDNS is the abbreviation of Dynamic Domain Name Server. It is designed for user owned the DNS server with dynamic WAN IP address.
5.26 What is NTP Client?
NTP client is designed for fetching the current timestamp from Internet via Network Time protocol. User can specify time zone, NTP server IP address.
5.27 What is VPN?
VPN is the abbreviation of Virtual Private Network. It is designed for creating point-to point private link via shared or pub­lic network.
5.28 What is IPSEC?
IPSEC is the abbreviation of IP Security. It is used to transferring data securely under VPN.
Page 69
69
CNet Global Technology Inc.
www.CNetusa.com
5.29 What is WLAN Block Relay between Clients?
An Infrastructure Basic Service Set is a BSS with a component called an Access Point (AP). The access point provides a local relay function for the BSS. All stations in the BSS communicate with the access point and no longer communicate di­rectly. All frames are relayed between stations by the access point. This local relay function effectively doubles the range of the IBSS.
5.30 What is WMM?
WMM is based on a subset of the IEEE 802.11e WLAN QoS draft standard. WMM adds prioritized capabilities to Wi-Fi networks and optimizes their performance when multiple concurring applications, each with different latency and through­put requirements, compete for network resources. By using WMM, end-user satisfaction is maintained in a wider variety of environments and traffic conditions. WMM makes it possible for home network users and enterprise network managers to decide which data streams are most important and assign them a higher traffic priority.
5.31 What is WLAN ACK TIMEOUT?
ACK frame has to receive ACK timeout frame. If remote does not receive in specified period, it will be retransmitted.
5.32 What is Modulation Coding Scheme (MCS)?
MCS is Wireless link data rate for 802.11n. The throughput/range performance of an AP will depend on its implementation of coding schemes. MCS includes variables such as the number of spatial streams modulation, and the data rate on each stream. Radios establishing and maintaining a link must automatically negotiate the optimum MCS based on channel con­ditions and then continuously adjust the selection of MCS as conditions change due to interference, motion, fading, and other events.
5.33 What is Frame Aggregation?
Every 802.11 packet, no matter how small, has a fixed amount of overhead associated with it. Frame Aggregation combines multiple smaller packets together to form one larger packet. The larger packet can be sent without the overhead of the indi­vidual packets. This technique helps improve the efficiency of the 802.11n radio allowing more end user data to be sent in a given time.
5.34 What is Guard Intervals (GI)?
. A GI is a period of time between symbol transmission that allows reflections (from multipath) from the previous data
transmission to settle before transmitting a new symbol. The 802.11n draft specifies two guard intervals: 400ns (short) and 800ns (long). Support of the 400ns GI is optional for transmit and receive. The purpose of a guard interval is to introduce immunity to propagation delays, echoes, and reflections to which digital data is normally very sensitive.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use