CNB WCL-21S User Manual
WEATHERPROOF IR CAMERA
USER INFORMATION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION !
Explanation of two Symbols
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR
MOISTURE"
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of un-insulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance-(servicing) instructions in the literature
accompanying the appliance.
SPECIFICATIONS
MODEL HIGH RESOLUTION NORMAL RESOLUTION
Signal System
Image Sensor
Effective Pixels
Scanning Frequecy(H)
Scanning Frequecy(V)
Resolution
Video Output
S/N Ratio
Lens
Min Illunination
IR LED
IR LED Visible Range
White Balance
AGC
Shutter Speed
Supplied Voltage
Power Consumption
Dimensions
Operating Temperature/Humidity
Storage Temperature/Humidity
Weight
NTSC
PAL
NTSC
1/3” High Sensitivity CCD
768(H)x494(V) 752(H)x582(V) 510(H)x492(V) 500(H)x582(V)
15.734 KHz 15.625 KHz
59.94 Hz
600TV Lines 420TV Lines
1.0Vp-p (75Ω, composite)
50dB Min (AGC off)
Bulit-in Fixed Lens, f=6mm (Option:12mm)
0.05 Lux (High) , 0.01 Lux (Normal) , 0 Lux (IR LED On)
Intelligent IR
,
IR LED 36EA
Max 30m
Auto
Auto
NTSC - 1/60 ~ 1/120,000 sec
,
PAL - 1/50 ~ 1/120,000 sec
10V DC ~ 15V DC (Recomendation 12V DC ± 0.5V DC)
0.5A (Max 6.0W)
78.0 × 150.0mm
-10oC to +50oC / 30% to 80% RH
-20oC to +60oC / 20% to 90% RH
Approx.800g
Ver.1008E P/N:3810-0230A
PAL
50 Hz
OWNER ’S
MANUAL
DIGITAL IR CAMERA SERIES
Design and specifications are subject to change without notice.
DIMENSIONS(mm) Regulatory Notice
73.3
58.6
TO REDUCE THE RISK OF
ELECTRIC SHOCK
17.4
182.3
78
150
78
150.4
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions : (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules.These limits
are designed to provide reasonable protection against harmful interference
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and use in accordance with the instructions, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause interference, in which case the user
will be required to correct the interference at his own expense.
WARNING >>
Changes or modifications not expressly approved by the manufacturer
could void the user's authority to operate the equipment.
CAUTION >>
When this camera is installed near equipment, like a wireless communication
device that emits a strong electromagnetic field, some irregularity such as
on the monitor screen may happen.
noise
TROUBLESHOOTING
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact
an authorized technician.
?
The image does not appear on the
screen.
?
The image on the screen is dim.
?
The camera does not work properly,
the surface of the camera case is
hot, and a black line appears on the
screen.
?
The screen blinks a lot.
Check the power source for the monitor
and camera and ensure that the voltage
and polarity are properly connected and
being supplied correctly.
Check if the lens is stained. If dirty,
clean the lens with a soft, clean cloth.
Adjust the Back Focus of the lens again.
Check if you have connected the camera
to a proper power source and If there is
no problem with the power, turn the unit
off immediately and seek assistance
from our Customer Service department.
Check if the camera is pointed toward
the sun or a fluorescent lamp.
Adjust the angle or location of the camera
if too much light is coming into the screen.
Loading...