CNB GS3010PBX User Manual
B/W Box Camera Series
P/N : 3810-0113A
(Ver.0703E)
Design and specifications are subject to
change without notice.
B/W Box Camera Series
CCTV VIDEO CAMERA
4. NAME AND FUNCTIONS
CCTV VIDEO CAMERA
B/W CCD
B/W CCD
.
e
l
b
a
t
c
e
l
e
S
s
B/W
n
e
l
s
i
r
I
l
a
u
n
a
M
/
o
t
u
A
•
monochrome
B/W BOX CAMERA SERIES
CCTV VIDEO CAMERA
OWNER'S MANUAL
8 9
CCTV VIDEO CAMERA
CS-Mount Holding Screw
Used to readjust back focus of the camera.
There are two back focus lock screws.
These must be loosened before the camera
may be back focused.
Loosen the lock screws to turn the CS-mount
lens adaptor, and tighten the lock
screws after adjustment.
Auto Iris Lens Connector
Used to connect Auto Iris Lens plug.
Holder Screw Hole
Used to install the camera on an optional
holder.(Tripod or Bracket)
The optional holder must be equipped with
the screw specified as shown right.
1/4"- 20 UNC (20 THREAD)
L : 4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
C-Mount Lens Adapter
Used to attach C-mount lens.
CS-Mount Lens Adapter
Used to attach CS-mount lens.
L
Rear-view
①
Lens Select
Switch
③
Mode Setting
DIP Switch
(See page 11)
④
Power Input
Terminal
VIDEO DC
OFF
ON
BLC
S1S
DC 12V
DC 12V Input Model
AGC
L H
EI
FL
AI
2
ON
OFF
VIDEO OUT
Class 2 Only
DC
LEVEL
②
AGC Select Switch
⑤
DC Level Control
Volume
⑥
Video Output Connector
(BNC-Type)
Connect the video output of the camera to the video input of a monitor or other equipment.
When using a "loop through" connection of two or more monitors, set the 75Ω switch of only the final
monitor to on. Determine the type of cable according to the distance of the connected equipment.
NOTE
Do not turn any component's power
on until all connections are completed.
CCTV VIDEO CAMERA
16 17
CCTV VIDEO CAMERA
7. CONNECTIONS
To Power input terminal
Power Source
DC 12V
Lens Connector
When using an auto-iris lens, install the accessory lens plug
on the lens cable as follows.
Video Type lens : Set lens Switch to Video. Connect the lens cable of a video Type lens.
If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.
DC type lens : Set lens switch to DC. Connect the lens cable of a DC(Galvanometric) type lens.
AGC
L HVIDEO DC
OFF
EI
DC
FL
LEVEL
ON
ON
AI
DC 12V
S1S
2
OFF
VIDEO OUT
Class 2 Only
To Video input connector
BLC
If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.
Pin Assignment :
#
1
#
3
#
2
#
4
NOTE
VIDEO Iris Type Lens
Pin No.
#1
#2
#3
#4
After installing the connector plug, connect it to
the lens connector on the rear panel of camera.
Signal
+9V DC
Video(1.0Vp-p, high impedance, no sync)
N.C
GND
DC Iris Type Lens
Pin No.
Signal
#1
Damping coil (-)
#2
Damping coil (+)
#3
Drive coil (+)
#4
Drive coil (-)
CCTV VIDEO CAMERA
. User Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION!
Explanation of two Symbols
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"
2
CCTV VIDEO CAMERA
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.
. Contents
Thank you for purchasing this CCTV VIDEO CAMERA.
Before using this camera, please read this operation manual carefully to obtain
the best result and keep this manual for future reference.
1. SAFETY INSTRUCTIONS
2. PRECAUTIONS
3. FEATURES
..................................
4. NAME AND FUNCTIONS
. DC 12V Input Model
. AC 24V / DC 12V Input Model
. Mode Setting DIP Switch
4
CCTV VIDEO CAMERA
.............
............................
.............
......................
............
................
5
6
7
8
9
10
11
5. INSTALLATION (LENS)
. Mounting a Lens
. Back-focus Adjustment
6. COMPOSITION
7. CONNECTIONS
. Lens Connector
8. SPECIFICATIONS
. DC 12V Input Model
. AC 24V / DC 12V Input Model
................
..........................
..................
...........................
..........................
...........................
.......................
.....................
...........
AC 24V / DC 12V Input Model
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
WARNING
The manufacturer could void the user's authority to operate the equipment.
CAUTION - To prevent electric shock and risk of fire hazards:
Do NOT use power sources except for that specified.
Do NOT expose this appliance to rain or moisture.
Rear-view
①
Lens Select
Switch
③
Mode Setting
DIP Switch
(See page 11)
④
Power Input
Terminal
VIDEO DC
OFF
ON
BLC
S1S
AC 24V / DC 12V
AGC
L H
EI
FL
AI
2
ON
OFF
VIDEO OUT
Class 2 Only
DC
LEVEL
②
AGC Select Switch
⑤
DC Level Control
Volume
⑥
Video Output Connector
(BNC-Type)
This installation should be made by a qualified service person and should abide to all local codes.
3
CCTV VIDEO CAMERA
1. SAFETY INSTRUCTIONS
Read Instructions
Read all of the safety and operating instructions
before using the product.
12
13
14
15
16
17
18
18
20
Retain Instructions
Save this instructions for later use.
Cleaning
Unplug this appliance from wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Water and Moisture.
Do not use this product near water or moisture.
(For example. near a bathtub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool,etc)
Installation
Do not place this product on an unstable cart, stand,
or table. The product may fall causing serious injury
to a child or adult, and damage to the product.
Use only with a cart or stand recommended by the
manufacturer, or sold with the product.
Mounting should follow the manufacturer's instructions,
and should use a mounting accessory recommended
by manufacturer.
Power source
This product should be operated only from the type
of power source indicated on the marking label.
If you are not sure of the type of power supplied to
your home, consult your dealer or local power
company.
5
CCTV VIDEO CAMERA
10 11
CCTV VIDEO CAMERA
5. INSTALLATION (LENS)
Please insert a lens cable when using the DC iris lens or
Video iris lens.
Lens select switch on the rear pannel should be set to
DC or VIDEO position when using
the AUTO iris lens.
When using the VIDEO type lens, please adjust a brightness
of image with volume attached with the lens.
When using the DC type lens, please
adjust a brightness of image by setup
menu on the rear panel.
12 13
CCTV VIDEO CAMERA
BLC (Back Light Compensation)
Strong light entering from an object's background may cause the lens iris to close,
there by possibly obscuring or darkening desired portions of the scene.
Back Light Compensation function automatically adjust the video level so as to
preserve visibillity in important section of the scene.
EI (Electronic Iris)
Electronic iris shutter is automatically controlled at the speed of
1/60 ~ 100,000 sec (EIA Mode), 1/50 ~ 100,000 sec (CCIR Mode).
Select this mode when using the manual lens.
FL (Flickerless)
If the camera is used with 50Hz fluorescent lighting, there maybe flicker on the
screen. In this case, FL switch should be set to ON position. But, FL switch
should be set to OFF in 60Hz power source. Flickerless mode can overcome
flickering on the screen in case that the AC power frequency is different from
the vertical sync frequency of the camera.
EIA (1/100), CCIR (1/120)
AI (Automatic Iris)
Electronic iris shutter is fixed 1/60 sec (EIA Mode), 1/50 sec (CCIR Mode).
Select this mode when using the DC or video iris vari-focal lens.
Remove the lens mount cap from the camera.
1
Attach or remove the C-mount adapter depending on the lens to be used.
2
-If the adapter is attached so tightly that it is difficult to remove it.
(Keep the C-mount adapter for possible future use.)
Attach the lens to the lens mount. Secure it so that it does not become loose.
3
If the lens has an auto-iris mechanism, connect the lens cable to the lens connector.
4
-When installing a video-iris lens, lens switch should be set to VIDEO position.
-When installing a galvanometric-iris lens, lens switch should be set to DC position.
When installing a manual lens, mode setting DIP switch should be set to EI position.
5
Mode Setting DIP Switch
OFF ON ON
ON
OFFS1OFF
BLC
OFF ON ON
ON
OFFS1OFF
BLC
OFF ON ON
ON
OFFS1OFF
BLC
OFF ON ON
ON
OFFS1OFF
BLC
Mounting a Lens
S2
Signal system
CCD Pick-up Element
Effective Pixels
S2
Video Output
Sync. System
Luminance S/N Ratio
S2
S2
CCTV VIDEO CAMERA
Horizontal Resolution
Sensitivity
CCTV VIDEO CAMERA
Signal system
CCD Pick-up Element
Effective Pixels
Video Output
Sync. System
Luminance S/N Ratio
Horizontal Resolution
Sensitivity
CCTV VIDEO CAMERA
CCTV VIDEO CAMERA
8. SPECIFICATIONS
Normal ResolutionHigh ResolutionMODEL
EIA CCIR EIA CCIR
2:1 Interlace Transfer 1/3 Inch Super HAD CCD
768(H) x 494(V) 752(H) x 582(V) 510(H) x 492(V) 500(H) x 582(V)
1.0V p-p, 75Ω
Internal Sync
More than 46dB (AGC OFF)
580 TV Lines 380 TV Lines
0.03 Lux(F1.2, 20IRE, AGC LOW) 0.01 Lux(F1.2, 20IRE, AGC LOW)
0.003 Lux(F1.2, 20IRE, AGC HIGH) 0.001 Lux(F1.2, 20IRE, AGC HIGH)
8. SPECIFICATIONS
Normal ResolutionHigh ResolutionMODEL
EIA CCIR EIA CCIR
2:1 Interlace Transfer 1/3 Inch Super HAD CCD
768(H) x 494(V) 752(H) x 582(V) 510(H) x 492(V) 500(H) x 582(V)
1.0V p-p, 75Ω
Internal Sync
More than 46dB (AGC OFF)
580 TV Lines 380 TV Lines
0.03 Lux(F1.2, 20IRE, AGC LOW) 0.01 Lux(F1.2, 20IRE, AGC LOW)
0.003 Lux(F1.2, 20IRE, AGC HIGH) 0.001 Lux(F1.2, 20IRE, AGC HIGH)
Lens Mount
Electronic Shutter
Auto Gain Control
Back Light Compensation
Flickerless
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature
Storage Temperature
Lens Mount
Electronic Shutter
Auto Gain Control
Back Light Compensation
Flickerless
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature
Storage Temperature
DC 12V Input Model
C/CS Mount
1/60 ~1/100,000 (EIA), 1/50 ~1/100,000(CCIR)
LOW / HIGH Selectable
ON / OFF Selectable
ON / OFF Selectable
DC Iris / Video Iris / Manual Lens
DC 12V (10V~15V)
100mA / 1.4W (Max)
-10℃~+50℃(Recommendation: -5℃~+40℃)
-20℃~+60℃
AC 24V / DC 12V Input Model
C/CS Mount
1/60 ~1/100,000 (EIA), 1/50 ~1/100,000(CCIR)
LOW / HIGH Selectable
ON / OFF Selectable
ON / OFF Selectable
DC Iris / Video Iris / Manual Lens
AC 24V(20V~28V) or DC 12V(10V~15V)
330mA / 4W (Max) 240mA 2.8W (Max)
-10℃~+50℃(Recommendation: -5℃~+40℃)
-20℃~+60℃
1918
CCTV VIDEO CAMERA
2120
CCTV VIDEO CAMERA
2. PRECAUTIONS
3. FEATURES
Handling
Do not disassemble the camera and never touch
parts inside the camera.
Do not drop the camera or subject it to shocks
and vibrations to avoid possible damage.
When attaching or removing the lens, handle
with care in order to that moisture and dust do
not enter the camera.
Installation and storage
Do not point the camera at the sun. This could
damage the camera whether it is operating or not.
Do not install the camera where the temperature
could exceed the allowable range.
6 7
CCTV VIDEO CAMERA
Be sure the ambient temperature is less than
40℃ in installation intended for long term
continuous operation.
Avoid installing in a humid or dusty place.
Avoid installing in places where there are
strong magnetic fields and electric signals.
Avoid installing in places where the camera
would be subject to strong vibrations.
Never expose the camera to rain and water.
High Sensitivity 1/3 Inch Super HAD CCD Pick-up.
Min lllumination : 0.001 Lux (Normal Resolution)
0.003 Lux (High Resolution)
Auto/Manual Iris lens Selectable.
AGC (Automatic Gain Control) LOW/HIGH
BLC (Back Light Compensation) ON/OFF
Flickerless ON/OFF
High Resolution : Horizontal 580 TV Lines High Resolution
380 TV Lines Normal Resolution
Back-focus Adjustment
6. COMPOSITION
. Memo
When a lens is mounted, adjustment of the back-focus may sometimes be required.
Adjust the lens focus ring when the correct focus cannot be obtained.
WITH A FIXED-FOCUS LENS
1) Fully open the aperture and set the focus ring to "∞"(infinity).
In the case of an auto-iris lens only, shoot a comparatively dark object so that the aperture is fully open.
2)
Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.
3) After adjusting the back-focus, tighten the back-focus screw.
. Lens Connector Plug (E-4-191J-100)
. Lens Mount Cap
. C-mount Adapter
. Owner's Manual
......................................................
......................................................
......................................................
............................
1
1
1
1
WITH A ZOOM LENS
1) Fully open the aperture and set the lens to the maximum tele-photo position. Then turn the focus ring to focus.
In the case of an auto-iris lens only, shoot a comparatively dark object so that the aperture is fully open.
2) Set the lens to its maximum wide-angle position.
3) Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.
4) After adjusting the back-focus, tighten the back-focus screw.
5) Repeat step 1)~3) until the difference between focusing position 1) and 2)becomes smallest.
CAUTION : Do not forcibly turn back-focus screw, it could cause damage to the camera.
CCTV VIDEO CAMERA
14 15
CCTV VIDEO CAMERA
The lens mount cap and C-mount adapter are attached when supplied.
!
Design and specifications are subject to change without notice.
This B/W video camera is designed to output video signals conforming
to the EIA(CCIR) standard. So that it cannot be used with video recorder
or B/W monitors which use B/W systems other than EIA(CCIR)
CCTV VIDEO CAMERA
CCTV VIDEO CAMERA
2322
CCTV VIDEO CAMERA
Loading...