CNB GP608 User Manual

WDR Camera Series

P/N : 3810-0023L (Ver.0609E)

Design and specifications are subject to change without notice.

Color Video Camera Series

WDR

Day & Night Color Camera

x Digital Zoom

480

•

TVL

•

(

•

)

(

)

•

DIGITAL CAMERA SERIES

COLOR VIDEO CAMERA

OWNER'S MANUAL

OSD

On-Screen Display

4. Features

1. Wide Dynamic Range (WDR)

SS-II DSP chip built-in SONY allows the camera to find the best picture conditions in any environment and automatically gives a necessary light level compensation, so you can always obtain the clear picture, the finest detail and perfect light contrast.

2. Day & Night

The camera provides automatic mode changeover by sensing day or night conditions. It can change color mode in the day condition for optimal color and BW mode in night condition for clear identification.

3. High Resolution

The horizontal resolution of 480TV lines at Color mode can be achieved by using a high density CCD having Double Speed 410,000 pixels SONY CCD, which provides clean, noiseless and reliable pictures.

4. Fine Picture Condition Under Very Low Illumination (Sense up)

1/3 high density CCD and digital processor permit high quality pictures to be captured in very low light condition.

5. VIDEO/ MANUAL/ DC Lens Selectable

The camera accepts 3 types of lenses (VIDEO/ MANUAL/ DC) and is set with the VIDEO/ ELC/ DC selection switch.

6. Electronic Iris

The electronic iris shutter is automatically controlled at the speed of 1/60~1/10,000sec (NTSC Models), 1/50~1/10,000sec (PAL Models)

7. Controlled by OSD menu and RS-485

You can control the camera using OSD menu and RS-485 jack at a remote place.

8. Privacy Zone

COLOR VIDEO CAMERA

5. Name and Function

CS-Mount Holding Screw

Used to readjust back focus of the camera. There are two back focus lock screws. These must be loosened before the camera may be back focused. Loosen the lock screws to turn the CS-mount lens adaptor, and tighten the lock screws after adjustment.

C-Mount Lens Adapter

Used to attach C-mount lens.

CS-Mount Lens Adapter

Used to attach CS-mount lens.

Auto Iris Lens Connector

Used to connect Auto Iris Lens plug.

Tripod Mounting Hole

Used to install the camera on an optional tripod. The tripod must be equipped with the screw specified as shown below.

1/4"- 20 UNC (20 THREAD) L : 4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard)

COLOR VIDEO CAMERA

Connecting to Power

Each model has different power specification, please check the name of the model and power specification before connecting to power source. Please refer to the sticker identifying the model, which is attached on the product, for power specification.

For DC 12V Power Type

The wire is polarized. Be careful of polarity. Use DC 12V power source.

( )

ELC

( )

DC 12V

DCVIDEO

CONTROL

VIDEO OUT

Class 2 Only

#24

(

0.22

㎟

)

0.078 0.050

)

0.028 0.018

DC12V

Class 2 Only

)]

#20

#18

(

)

0.83

㎟

0.018

0.006

#22

)

(

)

(

0.33

0.52

㎟

0.030

0.011

( ) ( )

Resistance of copper wire [at 20℃ (68˚F

Copper wire size

(

AWG)

Resistance(Ω

Voltage Drop(V/m

. As voltage may drop according to the length of electric cord as above table, a camera may malfunction if too long output line of adaptor is connected to the camera.

* Voltage for camera operation: DC 12V ± 10% * Voltage drops on above table are variable according to types of electric cord and makers.

COLOR VIDEO CAMERA

For AC 24V / DC 12V Power Type

The wire is non-polarized. Use AC 24V power source or DC 12V power source.

( )

ELC

( ) ( )

AC 24V / DC 12V

DCVIDEO

V.PHASE

( )

CONTROL

VIDEO OUT

Class 2 Only

AC24V/DC12V F.G

Class 2 Only

For AC 24V / DC 12V Power Type [UTP Video Output]

( )

ELC

DCVIDEO

( ) ( )

( )

VIDEO OUT

RS485 UTP OUT

AC 24V / DC 12V

Class 2 Only

When using AC 24V power, it is possible to supply the power within 100m. Use 4 wires by 2 pair of wires. When using DC 12V power, UTP wire can not be used for power line.

2 Wire

100m(Max)

COLOR VIDEO CAMERA

Power Supply

AC 24V

PELCO "D" Byte Format

Command Message

BYTE 1

MSG

0xFF

BYTE 1

MSG

0xFF

BYTE 1

MSG

0xFF

BYTE 1

MSG

0xFF

BYTE 1

MSG

0xFF

BYTE 1

MSG

0xFF

BYTE 1

MSG

0xFF

BYTE 1

MSG

0xFF

COLOR VIDEO CAMERA

BYTE 2 CamID

BYTE 3

0x00

BYTE 3

0x00

BYTE 3

0x01

BYTE 3

0x00

BYTE 3

0x40

BYTE 3

0x88

BYTE 3

0x08

BYTE 3

0x00

Pelco Keyboard (95+ PATTERN)

Zoom TeleFunction

BYTE 4

0x20

BYTE 5

0x00

BYTE 6

0x00

BYTE 7

Checksum

MSG

BYTE 1

0xFF

BYTE 2 CamID

BYTE 3

0x00

Menu On / OffFunction

BYTE 4

BYTE 5

BYTE 6

0x23

0x00

0x5F

BYTE 7

Checksum

Zoom WideFunction

BYTE 4

BYTE 5

BYTE 6

0x40

0x00

BYTE 7

Checksum

Focus NearFunction

BYTE 4

BYTE 5

BYTE 6

0x00

BYTE 7

Checksum

V/D Keyboard (Set Preset + 98)

Focus FarFunction

BYTE 4

BYTE 5

BYTE 6

0x80

BYTE 7

0x00

Menu On / OffFunction

Checksum

BYTE 4

BYTE 5

BYTE 6

0x00

BYTE 7

Checksum

MSG

BYTE 1

0xFF

BYTE 2 CamID

BYTE 3

0x00

Menu On / OffFunction

BYTE 4

BYTE 5

BYTE 6

0x03

0x00

0x62

BYTE 7

Checksum

Power OnFunction

BYTE 4

BYTE 5

BYTE 6

0x00

BYTE 7

Checksum

Power OffFunction

BYTE 4

BYTE 5

BYTE 6

0x00

BYTE 7

Checksum

Pelco D StopFunction

BYTE 4

BYTE 5 BYTE 6 BYTE 7

0x00

Don't care

Checksum

COLOR VIDEO CAMERA

8. Communication Protocol

Main Menu- D & N

Press the MENU button to access the D & N mode.

D/N MODE

TELE / WIDE

LEVEL FILTER DLY INITIAL EXIT

Your camera provides automatic mode changeover by CDS sensing day or night conditions. It changes to Color mode in day condition for optimal color and to BW mode in night condition for clear identification.

1. Press the SET button to display the MENU and move the indicator to 'D&N MODE' using the T or W button.

2. Set 'D/N MODE' to the desired mode using the LEFT( ) or RIGHT( ) button.

AUTO : DAY & NIGHT AUTO Mode / DAY : Only Day NIGHT : Only NIGHT / EXT : Externel Interface (IR LED)

Set 'LEVEL' to the desired mode using the LEFT( ) or RIGHT( ) button.

(15 : 40Lux, 28 : 30Lux, 48 : 20Lux, 88 : 10Lux, 128 : 5Lux, 200 : 1Lux) This level is setting up the turning point of the filter. For example, if the user set up the level to 48, the filter will be switched at 20Lux. The level can be chosen from 0 to 200. Please set up the level higher when you install this camera into the housing. (example : Level 128)

Set 'FILTER DLY' to the desired mode using the LEFT( ) or RIGHT( ) button.

According to user's need, the turning delay time of 0~15 seconds can be given.

5. INITIAL

INITIAL D&N MODE.

6. EXIT

RETURN to MAIN MENU.

COLOR VIDEO CAMERA

D & N

AUTO 48 10 ON

Main Menu- WDR

Press the MENU button to access the WDR mode.

WDR MODE

TELE / WIDE

WDR LEVEL BACK LIGHT BLC LEVEL INITIAL EXIT

1. Set 'WDR MODE' to 'ON/OFF' using the LEFT( ) or RIGHT( ) button.

2. Set 'WDR LEVEL' to the desired mode using LEFT( ) or RIGHT( ) button.

0~15 Ranged and adjust the brightness in WDR Mode.

3. Set 'BACK LIGHT' to 'ON/OFF' using the LEFT( ) or RIGHT( ) button.

4. Set 'BLC LEVEL' to the desired mode using LEFT( ) or RIGHT( ) button.

0~15 Ranged and adjust BLC Gain.

5. INITIAL

INITIAL WDR MODE.

6. EXIT

RETURN to MAIN MENU.

WDR

OFF 4 OFF 10 ON

COLOR VIDEO CAMERA

Model

Signal System

CCD Pick-up Element

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Resolution

Sensitivity

Lens Mount

Electronic Shutter

White Balance

Wide Dynamic Range

Day & Night

Auto Gain Control

Back Light Compensation

Flickerless

Supplied Voltage

Power Consumption

Operating Temperature

Storage Temperature

Dimensions (WxHxD)

Weight

COLOR VIDEO CAMERA

10. Specifications

2 : 1 Interalce Transfer 1/3 inch Double Scan CCD

768(H) x 494(V) 752(H) x 582(V)

Composite : 1.0V p-p, 75Ω, Unbalanced

0.1 Lux(DSS 2FLD, Color), 0.001 Lux(DSS Max, Color), 0.0003 Lux(DSS Max, BW)

1/60 ~ 1/10000 1/50 ~ 1/10000

-10℃~+50℃(Recommendation : -5℃~+40℃)

-AC 100V~AC 240V Input Model

DAY & NIGHT / WDR

High Resolution

NTSC PAL

Internal Sync.

More than 50dB (AGC OFF / BW Mode)

Horizontal : 480 TV

C / CS Mount

AWB (AUTO, HOLD, USER)

On / Off Selectable

AUTO / DAY / NIGHT / EXT Selectable

OFF / LOW / MID / HIGH Selectable

On / Off Selectable

AC 100V ~ AC 240V

6.0W (Max)

-20℃~+60℃

65 x 59.6 x 122.5mm

Approx. 430g

Model

Signal System

CCD Pick-up Element

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Resolution

Sensitivity

Lens Mount

Electronic Shutter

White Balance

Wide Dynamic Range

Day & Night

Auto Gain Control

Back Light Compensation

Flickerless

Supplied Voltage

Power Consumption

Operating Temperature

Storage Temperature

Dimensions (WxHxD)

Weight

WDR ONLY

High Resolution

NTSC PAL

2 : 1 Interalce Transfer 1/3 inch Double Scan CCD

768(H) x 494(V) 752(H) x 582(V)

Composite : 1.0V p-p, 75Ω, Unbalanced

Internal Sync.

More than 50dB (AGC OFF / BW Mode)

Horizontal : 480 TV

0.1 Lux (DSS 2FLD, Color), 0.001 Lux (DSS Max, Color)

C / CS Mount

1/60 ~ 1/10000 1/50 ~ 1/10000

AWB (AUTO, HOLD, USER)

On / Off Selectable

No Option

OFF / LOW / MID / HIGH Selectable

On / Off Selectable

AC 100V ~ AC 240V

6.0W (Max)

-10℃~+50℃(Recommendation : -5℃~+40℃)

-20℃~+60℃

65 x 59.6 x 122.5mm

Approx. 430g

COLOR VIDEO CAMERA

. User Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION!

Explanation of two Symbols

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

literature accompanying the appliance.

THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.

"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"

COLOR VIDEO CAMERA

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance-(servicing) instructions in the

INFORMATION

This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

WARNING

The manufacturer could void the user's authority to operate the equipment.

CAUTION - To prevent electric shock and risk of fire hazards:

Do NOT use power sources except for that specified.

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should abide to all local codes.

COLOR VIDEO CAMERA

DC 12V Input Model

① Function Setup Button

⑤ Power Input Terminal

( )

( ) ( )

( )

DC 12V

CONTROL

VIDEO OUT

Class 2 Only

ELC

DCVIDEO

② Lens Selection Swicth

④ Remote Jack

⑥ Video Out Jack

AC 24V/DC 12V Input Model

② Lens Selection

① Function

Setup Button

⑤ Power Input Terminal

( )

( ) ( )

( )

AC 24V / DC 12V

CONTROL

V.PHASE

VIDEO OUT

Class 2 Only

ELC

DCVIDEO

Swicth

③ V.PHASE Adjustment V.R

Left( ):Internal Right( ):

External

④ Remote Jack

⑥ Video Out Jack

AC 100V~AC 240V Input Model

( )

① Function Setup Button

( ) ( )

( )

POWER INLET

⑤ Power AC IN

COLOR VIDEO CAMERA

ELC

CONTROL

VIDEO OUT

DCVIDEO

② Lens Selection Swicth

④ Remote Jack

⑥ Video Out Jack

UTP Transmission Model

( )

① Function Setup Button

⑦ UTP Video

Output Terminal

①

Function Setup Button

Functions can be setup using 5 buttons on the camera's rear panel.

( )

( ) ( )

( )

②

Lens Selection Switch

Used to choose DC or VIDEO or ELC according to the type of your Lens.

③

V.PHASE Adjustment V.R (AC 24V / DC 12V Input Model)

If the camera is to be used in LineLock mode, the vertical phase may require adjustment to synchronize the vertical phase of the camera with other camera in the system. Make this adjustment when the vertical phase of the camera does not match with other cameras or systems. For correct adjustment, use a multi-channel oscilloscope. The V.PHASE adjustment can be readjusted.

④

Remote Jack (See page 21)

Used to connect remote plug.

⑤

POWER Input Terminal Used to connect an AC 24V or DC 12V power source. Used to connect a DC 12V power source. Used to connect an AC 100V~AC 240V power source.

⑥

VIDEO OUT Jack Used to connect an external video monitor in jack.

⑦

UTP Video Output Terminal These terminals provide a composite video output signal which may be

transmitted over a twisted-pair connection to furnished with a suitable receiver.

( ) ( )

( )

RS485 UTP OUT

MENU Buttons : Used to access menu mode. Also used to essape menu mode.

UP/DOWN Buttons : Used to choose the desired menu item. It also moves the cursor up or down in the menu screen.

LEFT/RIGHT Buttons: Used to change the parameter of the selected menu item. It also moves the cursor the left of right in the menu screen.

ELC

VIDEO OUT

AC 24V / DC 12V

Class 2 Only

② Lens Selection Swicth

DCVIDEO

⑥ Video Out Jack

⑤ Power Input

Terminal

COLOR VIDEO CAMERA

Notes

. Be sure to connect power after all the installation is done. . Note that AC adaptor is not supplied with camera. . Use only AC 24V / DC12V UL listed class 2 power supply. . Do not use power sources other than that specified.

For AC 100V ~ AC 240V Power Type

( )

ELC

DCVIDEO

( )

CONTROL

VIDEO OUT

Cabel

- Brown

- Blue

- Green

COLOR VIDEO CAMERA

( ) ( )

POWER INLET

AC Power Input

Frame Ground

Connecting to Monitor

For BNC Video Output Model

Connect the VIDEO out jack to the monitor video in jack.

Camera

( )

ELC

( ) ( )

AC 24V / DC 12V

As the connecting method varies with the instruments, refer to the manual supplied with the instrument.

DCVIDEO

V.PHASE

( )

CONTROL

VIDEO OUT

Class 2 Only

Connect the cable after power is turned off.

Set the 75Ω/ Hi-Z selection switch as shown below if you have an intermediate device.

CCD Camera

( )

( ) ( )

( )

CONTROL

AC 24V / DC 12V

V.PHASE

Class 2 Only

VIDEO OUT

ELC

DCVIDEO

Intermediate

Video Receiver

COLOR VIDEO CAMERA

Monitor

End monitor

9. Operating Camera

Configuration of The Menu

GENERAL

AWB

A E

D & N

WDR

CAMERA ID ZONE LABEL NEGA/POSI SHARPNESS MIRROR FREEZE PROTOCOL INITIAL EXIT WB MODE RED CONT BLUE CONT PUSH AUTO INITIAL EXIT BRIGHTNESS FLICKERLESS SHUTTER SPD AGC MAX SET MAX FLD SET INITIAL EXIT D/N MODE LEVEL FILTER DLY INITIAL EXIT WDR MODE WDR ELVEL BACK LIGHT BLC LEVEL INITIAL EXIT

COLOR VIDEO CAMERA

000 ~ 255

SET POSI/NEGA 0 ~ 15 NORMAL,MIRROR,VERTICAL,ROTATE ON, OFF DEF, P/D ON, OFF

AUTO, HOLD, USER NOT USE(AUTO, HOLD), 1~255(USER) NOT USE(AUTO, HOLD), 1~255(USER) NOT USE(AUTO, USER), OFF/PUSE(HOLD) ON, OFF

0 ~ 60 ON(PAL:x120, NTSC: x100), OFF x250, x500, x1000, x2000, x4000, x10000 AGC OFF, LOW, MID, HIGH OFF, 2~20 FLD, 40 FLD, 80 FLD, 160 FLD ON, OFF

AUTO, DAY, NIGHT, EXT 0 ~ 200 0 ~ 15 SEC ON, OFF

ON, OFF 0 ~ 15 ON, OFF 0 ~ 15 ON, OFF

PRIVACY

AREA MASK

1 ~ 4

ON, OFF START X END X START Y END Y

DISPLAY

INITIAL EXIT CAMERA ID ZONE LABEL

ON, OFF

ON, OFF VERSION

INITIAL

INITIAL OFF STATE

ON STATE, OFF STATE

EIXT

Setting Up The Menu

Use five setup Menu buttons on Rear side of the camera.

DOWN Button (WIDE) LEFT Button UP Button (TELE) RIGHT Button

( )

( ) ( )

( )

AC 24V / DC 12V

CONTROL

V.PHASE

VIDEO OUT

Class 2 Only

ELC

DCVIDEO

COLOR VIDEO CAMERA

Main Menu- PRIVACY

Press the MENU button to access the PRIVACY mode.

PRIVACY

AREA

TELE / WIDE

MASK START X END X START Y END Y INITIAL EXIT

Set 'AREA' to the desired mode using LEFT( ) or RIGHT( ) button.

Total 4 categories can be designated.

Set 'MASK' to the desired mode using LEFT( ) or RIGHT( ) button.

Marks the area on the screen in state of 'ON'.

Set 'START X' to the desired mode using LEFT( ) or RIGHT( ) button.

Indicates the starting point of X axis.

Set 'END X' to the desired mode using LEFT( ) or RIGHT( ) button.

Indicates the ending point of X axis.

Set 'START Y' to the desired mode using LEFT( ) or RIGHT( ) button.

Indicates the starting point of Y axis.

Set 'END Y' to the desired mode using LEFT( ) or RIGHT( ) button.

Indicates the ending point of Y axis.

7. INITIAL

INITIAL PRIVACY MODE.

8. EXIT

RETURN to MAIN MENU.

1 OFF OFF

If MASK is not 'ON' in setting AREA, data on X, Y coordinates cannot be used.

COLOR VIDEO CAMERA

Main Menu- DISPLAY

Press the MENU button to access the DISPLAY mode.

DISPLAY

TELE / WIDE

1. CAMERA ID

MONITOR DISPLAY ON/OFF

2. ZONE LABEL

MONITOR DISPLAY ON/OFF

3. VERSION

CAMERA VERSION.

4. INITIAL

INITIAL DISPLAY MODE.

5. EXIT

RETURN to MAIN MENU.

CAMERA ID ZONE LABEL VERSION INITIAL EXIT

OFF OFF

2.1 ON

COLOR VIDEO CAMERA

11. Troubleshooting

If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician.

Problem Solutions

Nothing appears on the screen.

The image on the screen is dim.

The image on the screen is dark.

The camera is not working properly, and the surface of the camera is hot.

The image on the screen flickers.

COLOR VIDEO CAMERA

. Check that the power cord and line connection between the camera and monitor are fixed properly. . Check that you have properly connected VIDEO cable to the camera VIDEO output jack.

. Is lens stained with dirt? Clean your lens with soft, clean cloth. . Set the monitor to proper condition. . If the camera is exposed to too strong light, change the camera position. . Adjust the lens' focus properly.

. Adjust the contrast feature of the monitor. . If you have an intermediate device, set the 75Ω/ Hi-z properly. (refer to page 19) . Adjust DC Level, VR Level properly. (refer to page 10)

. Check that you have properly connected the camera to an appropriate power source. (refer to page 16~18)

. Is the camera facing to direct sunlight or fluoresent lighting? Change the camera position.

. Memo

Color Video Camera Series

COLOR VIDEO CAMERA

Model Description

Precautions

Composition

Features

Name and Function

Connection

Remote Controller Operation

Communication Protocol

Operating Camera

Specifications

10.

Troubleshooting

11.

COLOR VIDEO CAMERA

1. Model Description. Contents

Thank you for purchasing this COLOR VIDEO CAMERA.

Before operating the camera, confirm that you have the right camera model and proper power voltage.

In order to help you understand this manual, we'll introduce our model's description.

Resolution

Signal System

High

NTSC

High

NTSC

High

NTSC

High

NTSC

High

NTSC

High

NTSC

High

NTSC

High

NTSC

High

When using AC 24V / DC 12V, make sure use the adaptor over

PAL

Power Input

DC 12V

AC 24V / DC 12V

AC 100V~AC 240V

DC 12V

AC 24V / DC 12V

AC 100V~AC 240V

DAY&NIGHT

WDR

0.5A for AC 24V, over 1A for DC 12V.

COLOR VIDEO CAMERA

UTP

6. Connection

LENS

The lens is not supplied with this camera. Purchase a lens suitable for your environment. This camera accepts the auto iris lens and both C-and CS-mount lens.

Notes

. If the lens is marked with fingerprints or other marks, the image quality might be poor.

. It is recommended to use a high quality lens to improve the image quality under low illumination.

. For using main functions it is recommended to use

Auto Iris Lens with DC type.

Installing Auto Iris Lens

1. Peel approximately 8mm from the end of the lens cable outer cover.

2. Peel approximately 2mm from the end of the cable inner cover.

COLOR VIDEO CAMERA

8mm

2mm

3. Remove the cover from the iris lens plug supplied, and solder the lens cable to the plug as shown below.

Pin.No. VIDEO TYPE

RED (Power Source)

No. 3 Pin

No. 1 Pin

4. Remove the protective cap, and attach the lens to the camera by turning clockwise.

5. Connect the lens plug to the auto iris connector on the right side of the camera.

6. Set the VIDEO/ ELC/ DC selection switch to VIDEO or ELC or DC according to the type of the lens.

N.C

WHITE (Video Signal)

BLACK (GND)

No. 4 Pin

No. 2 Pin

DC TYPE

--- Damping

--- Damping +

--- Drive +

--- Drive

Lens cable

connector

( )

ELC

( ) ( )

V.PHASE

( )

CONTROL

VIDEO OUT

AC 24V / DC 12V

Class 2 Only

COLOR VIDEO CAMERA

DCVIDEO

Connecting to Monitor

For UTP Video Output Model

Connect the UTP video output terminal on the back of the product to the monitor.

Camera

( )

ELC

DCVIDEO

( ) ( )

( )

VIDEO OUT

RS485 UTP OUT

AC 24V / DC 12V

Class 2 Only

UTP Cable

300m(Max)

Connect UTP (Unshielded Twisted Pair) wire to the UTP output of the camera directly. UTP transmitter is included in the camera therefore additional UTP transmitter is not necessary.

UTP receiver is necessary to connect UTP wire to Monitor or DVR.

When connecting UTP wire, make sure the polarity of the video signal.

Use UTP wire "CAT5 24AWG" to have the best transmission quality.

The twisted-pair output cannot be used at the same time as the Composite Video output.

COLOR VIDEO CAMERA

Monitor(or DVR)

UTP Receiver

Remote Jack

1 2 3 4 5

No. Function

1 2 3 4 5

R+ (RS-485) R- (RS-485)

DAY/NIGHT OUTPUT "H"

GND

DAY/NIGHT INPUT(EXT) "L"

Remote Input Jack (RS485)

It is a terminal that controls the function of the camera at long distance.

PC Interface

RS-232C TO RS-422 Converter

Tx +

R +

T +

Rx +

GND

RS-232C D-Sub Connector (PC)

NAME

1. Frame GND

2. RD

3. TD

4. DTR

5. Signal GND

6. DSR

7. RTS

8. CTS

9. RI

DVR Interface (RS-485 Communication)

R +

DAY / NIGHT Output

It is the function that can turn on external IR LED Lamp by detecting the sensitivity on CDS when the Day / Night mode is set "Auto" on the OSD menu of the camera.

Day/Night Out

4 GND

DAY / NIGHT External Input

It is the function that can be switched to DAY Mode or NIGHT Mode by receiving the Day/Night on/off signal from external light sensor or IR LED LAMP. When Day / Night Mode is set " External" on the OSD menu of the Camera.

GND

4 5

D/N ON (EXIT)

TRX +

TRX

5V / 10mA

: IR LED ON(NIGHT)

: IR LED OFF(DAY)

Open contact : DAY Close contact : NIGHT

COLOR VIDEO CAMERA

DVR (RS-485)

Main Menu- GENERAL

Press the MENU button to access the GENERAL mode.

GENERAL

GENERAL AWB AE D & N WDR PRIVACY DISPLAY INITIAL

TELE / WIDE

EXIT

CAMERA ID ZONE LABEL NEGA / POSI

Move up and down using the TELE/ WIDE button.

SHARPNESS MIRROR FREEZE PROTOCOL INITIAL EXIT

1. CAMERA ID

Set 'CAMERA ID' to the desired mode using LEFT( ) or RIGHT( ) button. Press the MENU button to display the 'GENEARL' and move the arrow indicator to 'CAMERA ID' using the T or W button. If the 'CAMERA ID' feature is set to 'ON', the name will be displayed on the monitor. (Main 'DISPLAY' MENU)

COLOR VIDEO CAMERA

GENERAL

CAMERA ID ZONE LABEL NEGA / POSI SHARPNESS MIRROR FREEZE PROTOCOL

001 SET POSI 7 NORMAL OFF P/D ON

Can be changed using the / button.

- P/D

(Pelco-D)

- DEF

(Default)

2. ZONE LABEL

You can enter up to 10 characters. Move the curser to character-enter location by using the LEFT( ) or RIGHT( ) button. Select the desired character by using T , W button. The factory default characters are A~Z,a~z,0~9, ~, !, #, *, -, +, /, :, ;, ?, ., ", _, (, ), &, %, , , , , EXIT : RETURN to GENERAL MENU

If the 'DISPLAY MENU' feature is set to 'ZONE LABEL - ON', the name will be displayed on the monitor.

ZONE LABEL

UP/DN - CHAR SELECT LE/RI - POSITION MENU - EXIT

3. NEGA/POSI

Select Nega/Posi.

4. SHARPNESS

Adjust the Sharpness of the screen.

5. MIRROR

NORMAL : Deactivation MIRROR : Reverse turn Left or Right. VERTICAL : Reverse turn Up or Down. ROTATE : Rotate the Screen to 180.

6. FREEZE

Used when paused Video is needed.

7. PROTOCOL

P/D: Pelco-D DEF: Default

8. INITIAL

INITIAL GENERAL MODE

9. EXIT

RETURN to MAIN MENU

COLOR VIDEO CAMERA

10. Specifications -DC12V Input Model

Model

Signal System

CCD Pick-up Element

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Resolution

Sensitivity

Lens Mount

Electronic Shutter

White Balance

Wide Dynamic Range

Day & Night

Auto Gain Control

Back Light Compensation

Flickerless

Supplied Voltage

Power Consumption

Operating Temperature

Storage Temperature

Dimensions (WxHxD)

Weight

COLOR VIDEO CAMERA

0.1 Lux(DSS 2FLD, Color), 0.001 Lux(DSS Max, Color), 0.0003 Lux(DSS Max, BW)

High Resolution

NTSC PAL

2 : 1 Interalce Transfer 1/3 inch Double Scan CCD

768(H) x 494(V) 752(H) x 582(V)

Composite : 1.0V p-p, 75Ω, Unbalanced

More than 50dB (AGC OFF / BW Mode)

1/60 ~ 1/10000 1/50 ~ 1/10000

AWB (AUTO, HOLD, USER)

AUTO / DAY / NIGHT / EXT

OFF / LOW / MID / HIGH Selectable

-10℃~+50℃(Recommendation : -5℃~+40℃)

DAY & NIGHT / WDR

Internal Sync.

Horizontal : 480 TV

C / CS Mount

On / Off Selectable

DC 12V (10V ~ 15V)

400mA 4.8W (Max)

-20℃~+60℃

65 x 59.6 x 122.5mm

Approx. 430g

Model

Signal System

CCD Pick-up Element

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Resolution

Sensitivity

Lens Mount

Electronic Shutter

White Balance

Wide Dynamic Range

Day & Night

Auto Gain Control

Back Light Compensation

Flickerless

Supplied Voltage

Power Consumption

Operating Temperature

Storage Temperature

Dimensions (WxHxD)

Weight

WDR ONLY

High Resolution

NTSC PAL

2 : 1 Interalce Transfer 1/3 inch Double Scan CCD

768(H) x 494(V) 752(H) x 582(V)

Composite : 1.0V p-p, 75Ω, Unbalanced

Internal Sync.

More than 50dB (AGC OFF / BW Mode)

Horizontal : 480 TV

0.1 Lux (DSS 2FLD, Color), 0.001 Lux (DSS Max, Color)

C / CS Mount

1/60 ~ 1/10000 1/50 ~ 1/10000

AWB (AUTO, HOLD, USER)

On / Off Selectable

No Option

OFF / LOW / MID / HIGH Selectable

On / Off Selectable

DC 12V (10V ~ 15V)

400mA 4.8W (Max)

-10℃~+50℃(Recommendation : -5℃~+40℃)

-20℃~+60℃

65 x 59.6 x 122.5mm

Approx. 430g

COLOR VIDEO CAMERA

2. Precautions

Do not install the camera in extreme temperature conditions.

Do use the camera under conditions where temperatures are within

-10°C to 45°C. Especially be careful for ventilation under high temperature.

Do not install or use the camera in an environment where the humidity is high.

It can cause the image quality to be poor.

Do not install the camera under unstable lighting conditions.

Severe lighting change or flicker can cause the camera to work improperly.

Never use the camera close to a gas or oil leak.

It can cause malfunctions to occur.

Do not disassemble the camera.

There are no user-serviceable parts inside it.

Do not drop the camera or subject them to physical shocks.

It can cause malfunctions to occur.

Never keep the camera face to strong light directly.

It can damage CCD.

Do not expose the camera to rain or spill beverage on it.

If it gets wet, wipe it dry immediately. Liquids can contain minerals that corrode the electronic components.

Note When this camera is installed near wireless communication devices that emits strong electromagnetic field, irregularity such as noise on the monitor may appear.

COLOR VIDEO CAMERA

3. Composition

1. WDR Color Video Camera .................

2. Auto Iris Lens Plug ..................

3. Remote Plug ....................

5. C-Mount Adapter ....................

6. Owner's Manual ................

•

)

•

(

R'S

c r

e e

i s

l a

COLOR VIDEO CAMERA

Installing C/CS-Mount Lens

Before mounting a lens, please check whether it is a C-mount or CS-mount lens. The back focus is set for the CS-mount lens at the factory.

Mounting a CS-Mount Lens

After removing the protecting cap, attach the lens into the camera by turning clockwise.

Mounting a C-Mount Lens

1. Attach the C-Mount lens adapter by turning clockwise.

The remote controller is optional item.

Receiver

Power

DC 12V, 500mA

RS-485 Signal

1 2 3 4

- White Terminal :

- Black Terminal :

Cable Connection

Receiver & Remote Control

Pelco-D/ RS-485

Remote Control

①

Camera Selection

7. Remote Controller Operation (Pelco-D)

①

Notes

. Use the lens under the specification as shown. Otherwise the lens can damage the camera or abnormal fixing may result.

2. Attach the lens to the camera by turning clockwise.

②

C-mount lens : 10mm or less

•

(

)

. A heavy lens may disturb the balance with the camera and possibly result in damage. Don't use a lens heavier than 450g.

It is recommended to set the lens ALC mode to Av mode(Average).

Pk mode can be occurred hunting.

COLOR VIDEO CAMERA

CS-mount lens : 5mm or less

COLOR VIDEO CAMERA

⑥

⑤

COLOR VIDEO CAMERA

SEQ PAN

PROG

FAR

AUTO

FOCUS

NEAR

ZOOM

TELE

WIDE

- After camera connects with receiver, firstly check camera I.D.

- Press camera I.D. number(1~39 buttons) on the top of wireless remote controller.

Example: ZOOM IN I.D. No.5: Press 5 +<TELE

I.D. No.15: Press I.D. No.24: Press I.D. No.34: Press

Caution :

are selected from No.1 to No.39. over I.D. No.40, you will have a use limit.

- Initial camera I.D. number is set up No.0

③

when it takes out of manufacturer's warehouse.

②

Menu (PROG): Shows / Hides Menu.

④

③ (

TELE):

④ (

WIDE):

⑤ (

NEAR):

⑥ (

FAR):

Usually camera I.D. number

Moves up and down items.

Set data for the selected items.

> + 5 +<TELE + 4 +<TELE + 4 +<TELE

> > >

Signal (RS-485)

DVR System

Pelco-D Keyboard

COLOR VIDEO CAMERA

Main Menu- AWB

Press the MENU button to access the AWB mode.

Set 'AUTO' to the desired mode using LEFT( ) or RIGHT( ) button.

WB MODE

TELE / WIDE

RED CONT BLUE CONT PUSH AUTO INITIAL EXIT

AWB

AUTO NOT USE NOT USE NOT USE ON

'WB' is automatically set up between 2500~9500.

Set 'HOLD' to the desired mode using LEFT( ) or RIGHT( ) button.

WB MODE

TELE / WIDE

RED CONT BLUE CONT PUSH AUTO INITIAL EXIT

If 'PUSH AUTO is selected as 'ON', it fixes up the value setting the current WB.

Set 'USER' to the desired mode using LEFT( ) or RIGHT( ) button.

WB MODE

TELE / WIDE

RED CONT BLUE CONT PUSH AUTO INITIAL EXIT

AWB

HOLD NOT USE NOT USE OFF OFF

USER 101 60 NOT USE OFF

'WB' gains can be set by using RED CONT, BLUE CONT.

4. INITIAL

5. EXIT

INITIAL AWB MODE.

RETURN to MAIN MENU.

COLOR VIDEO CAMERA

Main Menu- AE

Press the MENU button to access the AE mode.

BRIGHTNESS

TELE / WIDE

FLICKERLESS SHUTTER SPD AGC MAX SET MAX FLD SET INITIAL EXIT

Set 'BRIGHTNESS' to the desired mode using LEFT( ) or RIGHT( ) button.

0~60 BRIGHTNES Levels can be adjusted.

Set 'FLICKERLESS' to the desired mode using the LEFT( ) or RIGHT( ) button.

OFF : Deactivation ON : 1/100(PAL Models), 1/120(NTSC Models)

Set 'SHUTTER SPD' to the desired mode using LIFT( ) or RIGHT( ) button.

NORMAL : Deactivation X250 : 1/250 sec, X500:1/500 sec, X1000:1/1000 sec, X2000:1/2000 sec, X4000 : 1/4000 sec, X10000:1/10000 sec

Set 'AGC MAX SET' to the desired mode using LIFT( ) or RIGHT( ) button.

AGC OFF : Deactivation LOW : Gain is increased or decreased from 0 to 10dB automatically according to the illumination. MID : Gain is increased or decreased from 0 to 20dB automatically according to the illumination. HIGH : Gain is increased or decreased from 0 to 30dB automatically according to the illumination.

Set 'MAX FLD SET' to the desired mode using LIFT( ) or RIGHT( ) button.

OFF, 2 FLD ~ 20 FLD, 40 FLD, 80 FLD, 160 FLD

6. INITIAL

INITIAL AE MODE.

7. EXIT

RETURN to MAIN MENU.

19 OFF NORMAL MID 2 FLD ON

COLOR VIDEO CAMERA

10. Specifications -AC 24V Input Model

Model

Signal System

CCD Pick-up Element

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Resolution

Sensitivity

Lens Mount

Electronic Shutter

White Balance

Wide Dynamic Range

Day & Night

Auto Gain Control

Back Light Compensation

Flickerless

Supplied Voltage

Power Consumption

Operating Temperature

Storage Temperature

Dimensions (WxHxD)

Weight

COLOR VIDEO CAMERA

0.1 Lux(DSS 2FLD, Color), 0.001 Lux(DSS Max, Color), 0.0003 Lux(DSS Max, BW)

High Resolution

NTSC PAL

2 : 1 Interalce Transfer 1/3 inch Double Scan CCD

768(H) x 494(V) 752(H) x 582(V)

Composite : 1.0V p-p, 75Ω, Unbalanced

Internal / External Sync.

More than 50dB (AGC OFF / BW Mode)

1/60 ~ 1/10000 1/50 ~ 1/10000

AWB (AUTO, HOLD, USER)

AUTO / DAY / NIGHT / EXT Selectable

OFF / LOW / MID / HIGH Selectable

AC 24V (20V~28V) or DC 12V (10V~15V)

-10℃~+50℃(Recommendation : -5℃~+40℃)

65 x 59.6 x 122.5mm

DAY & NIGHT / WDR

Horizontal : 480 TV

C / CS Mount

On / Off Selectable

600mA 7.2W (Max)

-20℃~+60℃

Approx. 430g

Model

Signal System

CCD Pick-up Element

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Resolution

Sensitivity

Lens Mount

Electronic Shutter

White Balance

Wide Dynamic Range

Day & Night

Auto Gain Control

Back Light Compensation

Flickerless

Supplied Voltage

Power Consumption

Operating Temperature

Storage Temperature

Dimensions (WxHxD)

Weight

WDR ONLY

High Resolution

NTSC PAL

2 : 1 Interalce Transfer 1/3 inch Double Scan CCD

768(H) x 494(V) 752(H) x 582(V)

Composite : 1.0V p-p, 75Ω, Unbalanced

Internal / External Sync.

More than 50dB (AGC OFF / BW Mode)

Horizontal : 480 TV

0.1 Lux (DSS 2FLD, Color), 0.001 Lux (DSS Max, Color)

C / CS Mount

1/60 ~ 1/10000 1/50 ~ 1/10000

AWB (AUTO, HOLD, USER)

On / Off Selectable

No Option

OFF / LOW / MID / HIGH Selectable

On / Off Selectable

AC 24V (20V~28V) or DC 12V (10V~15V)

600mA 7.2W (Max)

-10℃~+50℃(Recommendation : -5℃~+40℃)

-20℃~+60℃

65 x 59.6 x 122.5mm

Approx. 430g

COLOR VIDEO CAMERA

CNB GP608 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual