CNB G1960P User Manual

Digital Color Camera Series

OSD

On-Screen Display

COLOR VIDEO CAMERA

Main Menu -

SHUTTER SPEED CONTROL(2)

Menu [SPECIAL]-

MIRROR

P/N : 3810-0092A (Ver.0701E)

Color Video Camera Series

Design and specifications are subject to change without notice.

. User Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION!

Explanation of two Symbols

THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.

"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.

Color CCD

DSP

•

d e

•

(

)

DIGITAL CAMERA SERIES

Color CCD

SDNR

Super Digital Noise Reduction

SDNR

COLOR VIDEO CAMERA

OWNER'S MANUAL

INFORMATION

This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

WARNING

The manufacturer could void the user's authority to operate the equipment.

CAUTION - To prevent electric shock and risk of fire hazards:

Do NOT use power sources except for that specified. Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should abide to all local codes.

2) Shutter status and speed control

You can control brightness of the screen by the shutter speed.

①

󰼿

Press the MENU button to display the setup menu and move the arrow indicator to 'SHUTTER' using the UP or DOWN button.

②

󰼿Set 'SHUTTER' to the desired mode using the LEFT or RIGHT button.

SETUP

LENS

OFF : Deactivation

FLK: Flicker mode

- NTSC (1/100)

- PAL (1/120)

16 17

ESC : You can control the BRIGHTNESS.

③

󰼿When completed, press 'MENU'

NOTE

Don't expose the camera to fluorescent lamp directly not to get unstable image in the internal synchronization modes.

When the SHUTTER menu is set to FLK mode. SENS-UP can not work. Please control the menu.

SHUTTER

WHITE BAL. BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT

LENS

SHUTTER

WHITE BAL. BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT

LENS

SHUTTER

WHITE BAL. BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT

BRIGHTNESS 25

Press SET to Return

SETUP

Brightness

--AWC HIGH OFF

---

MANUAL FLK AWC HIGH OFF

---

MANUAL ESC AWC HIGH OFF

---

3) WHITE BAL. (White Balance)

When you need to control the color on the screen, use 'WHITE BALANCE' function.

MANUAL : When setting shutter speed manually.(Only for manual LENS mode) You can select speed from

- NTSC (x128~x2, 1/60~1/120,000 sec.)

- PAL (x128~x2, 1/50~1/120,000 sec)

SETUP

LENS

SHUTTER

WHITE BAL. BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT

MANUAL 1/60

Press SET to Return

①

󰼿Press the MENU button to display the SETUP menu and move the arrow indicator to 'WHITE BALANCE'

using the UP or DOWN button.

②

󰼿Set 'WHITE BAL.' To the desired mode using LEFT or RIGHT button.

LENS SHUTTER

WHITE BAL.

BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT

ATW(Auto Tracking White Balance): When color temperature is 1,800˚K~10,500˚K, select this mode. (ex. A fluorecent lamp, outdoor)

AWC(Auto White Balance Control): The white balance is automatically adjusted in a specific environment. In order to obtain the best result, press the set button while the camera focuses on white paper. If the environment including the light source is changed, you have to adjust the white balance again.

SHUTTER

SETUP

MANUAL MANUAL AWC HIGH OFF

---

Main Menu -

--AWC HIGH OFF

---

WHITE BALANCE

SPECIAL

CAMERA ID COLOR SYNC MOTION DET

PRIVACY

MIRROR SHARPNESS RESET RETURN

PRIVACY

AREA SEL

AREA STATE AREA TONE TOP DOWN LEFT RIGHT

Press SET to Return

--INT OFF ON OFF ON

AREA1 ON

80 10 25 20 40

MIRROR

: This mode reverses the image horizontally.

①

󰼿Press the MENU button to display the setup menu and move the arrow indicator to 'MIRROR' using the

UP and DOWN button.

②

󰼿SET 'MIRROR' to desired mode using the LEFT or RIGHT button.

SPECIAL

OFF : Deactivation

ON : Reverse image

LEFT and RIGHT.

CAMERA ID COLOR SYNC MOTION DET PRIVACY

MIRROR

SHARPNESS RESET RETURN

--INT OFF OFF OFF ON

3332

Menu [SPECIAL]-

SHARPNESS

①

󰼿Press the MENU button to display the setup menu and move the arrow indicator to 'SHARPNESS' using

the UP and DOWN button.

②

󰼿SET 'SHARPNESS' to the

desired mode using the LEFT or RIGHT button.

NOTE

1918

SHARPNESS

: The outline of the video image becomes cleaner and more distinctive as the level of SHARPNESS increases.

SPECIAL

CAMERA ID COLOR SYNC MOTION DET

OFF : Deactivation.

ON : SHARPNESS

control mode(level 0~31) when the level is up, the sharpness will make image clear. Please control the level as you want to get.

If the level goes up excessively, you can get the unnatural image with noise.

PRIVACY MIRROR

SHARPNESS

RESET RETURN

LEVEL

Press SET to Return

SHARPNESS

--INT OFF OFF OFF ON

Menu [SPECIAL]-

RESET

: To reset your camera to factory default setting.

RETURN

: Save the setting of SPECIAL function, and then move to SETUP menu.

RESET / RETURN

3534

. Contents

1. SAFETY INSTRUCTIONS

Thank you for purchasing this COLOR VIDEO CAMERA. Before using this camera, please read this operation manual carefully to obtain

the best result and keep this manual for future reference.

1. SAFETY INSTRUCTIONS

2. PRECAUTIONS

3. FEATURES

............................

..................................

4. NAME AND FUNCTIONS

5. OPERATING CAMERA

6. INSTALLATION (LENS)

. Mounting a Lens

. Back-focus Adjustment

..........................

.............

.................

..................

7. COMPOSITION

8. CONNECTIONS

. Lens Connector

9. SPECIFICATIONS

. DC 12V Input Model

. AC 24V / DC 12V Input Model

...........................

..........................

...........................

........................

......................

............

2. PRECAUTIONS

Handling

Do not disassemble the camera and never touch parts inside the camera.

Do not drop the camera or subject it to shocks and vibrations to avoid possible damage.

When attaching or removing the lens, handle with care in order to that moisture and dust do not enter the camera.

Installation and storage

Do not point the camera at the sun. This could damage the camera whether it is operating or not.

Do not install the camera where the temperature could exceed the allowable range.

Be sure the ambient temperature is less than 40℃ in installation intended for long term continuous operation.

Avoid installing in a humid or dusty place.

Avoid installing in places where there are strong magnetic fields and electric signals.

Avoid installing in places where the camera would be subject to strong vibrations.

Never expose the camera to rain and water.

6 7

Read Instructions

Read all of the safety and operating instructions before using the product.

Retain Instructions

Save this instructions for later use.

Cleaning

Unplug this appliance from wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Water and Moisture.

Do not use this product near water or moisture. (For example. near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool,etc)

3. FEATURES

High sensitivity 1/3 Inch Sony Super HAD CCD

Min. lllumination (F1.2, 30 IRE) : 0.1 Lux (Color)

0.0008 Lux (DSS x128)

DNR (Digital Noise Reduction)

It has an assistant reducing image noise efficiently and It shows clear and sharp image display even in the dark

Electronic day & night mode selectable.

High performance menus for functions

• Privacy zone selectable.

• Motion detection selectable.

• Various BLC Mode Selectable (OFF/ LOW/ MIDDLE/ HIGH)

• Sharpness enhanced adjustable.

• Flickerless On/Off

• Electronic Sensitivity-up (SENS-UP)

Installation

Do not place this product on an unstable cart, stand, or table. The product may fall causing serious injury to a child or adult, and damage to the product. Use only with a cart or stand recommended by the manufacturer, or sold with the product. Mounting should follow the manufacturer's instructions, and should use a mounting accessory recommended by manufacturer.

Power source

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.

6. INSTALLATION (LENS)

Please insert a lens cable when using the DC iris lens or Video iris lens.

Lens select switch on the rear pannel should be set to DC or VIDEO position when using the AUTO iris lens.

When a lens is mounted, adjustment of the back-focus may sometimes be required. Adjust the lens focus ring when the correct focus cannot be obtained.

Mounting a Lens

Remove the lens mount cap from the camera.

Attach or remove the C-mount adapter depending on the lens to be used.

- If the adapter is attached so tightly that it is difficult to remove it. (Keep the C-mount adapter for possible future use.)

Attach the lens to the lens mount. Secure it so that it does not become loose.

If the lens has an auto-iris mechanism, connect the lens cable to the lens connector.

- When installing a video-iris lens, lens switch should be set to VIDEO position.

- When installing a galvanometric-iris lens, lens switch should be set to DC position.

7. COMPOSITION

. Lens Connector Plug (E-4-191J-100)

. Lens Mount Cap

. C-mount Adapter

. Owner's Manual

......................................................

The lens mount cap and C-mount adapter are attached when supplied.

Design and specifications are subject to change without notice.

This color video camera is designed to output video signals conforming to the NTSC(PAL) standard. So that it cannot be used with video recorder or color monitors which use color systems other than NTSC(PAL).

............................

MANUAL : To fine adjust, select the Manual mode. You can increase or decrease the red or blue factor while monitoring the difference on the screen. Set to 'MANUAL' mode and press the MENU button, lncrease or decrease the value for RED(R-Gain) and BLUE(B-Gain), watching the color of the picture, and press the MENU button when you obtain the best color.

NOTE

Proper White Balance may not be obtained under the following conditions, in these cases select the AWC mode.

- When the scene contains mostly high color temperature object, such as a blue sky or sunset.

- When the scene is dim.

- If your camera faces fluorescent lamp directly or is installed in the place of the changing illumination.

Main Menu -

4) BACKLIGHT

When there is a strong backlight behind the object, clear images of the background as well as the object can still be obtained by using the BACKLIGHT function.

①

󰼿

Press the MENU button to display the SETUP menu and move the arrow indicator to 'BACKLIGHT' using the UP or DOWN button.

②

󰼿SET 'BACKLIGHT' to the desired mode using the LEFT or RIGHT button.

OFF LOW MIDDLE HIGH

SETUP

LENS SHUTTER WHITE BAL.

BACKLIGHT

AGC DNR SENS-UP SPECIAL EXIT

BLC ON BLC OFF

--AWC HIGH OFF

---

BACKLIGHT

When using the VIDEO type lens, please adjust a brightness of image with volume attached with the lens.

When using the DC type lens, please adjust a brightness of image by setup menu on the rear panel.

Main Menu -

5) AGC (Auto Gain Control)

AGC is to get bright picture. Higher GAIN level, getting brighter screen. But you can get noise increase.

AGC

①

󰼿Press the MENU button to display the SETUP menu and move the arrow indicator to 'AGC' using the

UP or DOWN button.

②

󰼿SET 'AGC' to the desired mode using the LEFT or RIGHT button.

OFF LOW MIDDLE HIGH

SETUP

LENS SHUTTER WHITE BAL. BACKLIGHT

AGC

DNR SENS-UP SPECIAL EXIT

--AWC HIGH OFF

---

Main Menu -

6) DNR (Digital Noise Reduction)

DNR reduce the noise on the screen.

①

󰼿Press the MENU button to display the SETUP menu and move the arrow indicator to 'DNR' using the UP or

DOWN button.

②

󰼿SET 'DNR' to the desired mode using the LEFT or RIGHT button.

LENS SHUTTER WHITE BAL. BACKLIGHT AGC

DNR

SENS-UP SPECIAL EXIT

SETUP

--AWC HIGH OFF

---

NOTE

OFF : Deactivation LOW : Low reduction

of the noise MIDDLE : Middle

reduction of the noise HIGH : High reduction

of the noise

Afterimage may appear with DNR If you change the 'AGC' menu from AGC-L to AGC-H, sensitivity is

increasing as well as noise on the screen. When selected 'AGC' menu OFF, DNR doesn't work.

DNR

2120

36 37

Back-focus Adjustment

WITH A FIXED-FOCUS LENS

1) Fully open the aperture and set the focus ring to "∞"(infinity). In the case of an auto-iris lens only, shoot a comparatively dark object so that the aperture is fully open.

Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.

3) After adjusting the back-focus, tighten the back-focus screw.

WITH A ZOOM LENS

1) Fully open the aperture and set the lens to the maximum tele-photo position. Then turn the focus ring to focus. In the case of an auto-iris lens only, shoot a comparatively dark object so that the aperture is fully open.

2) Set the lens to its maximum wide-angle position.

3) Loosen the two back-focus screws with a L-wrench, and turn the lens mount to focus.

4) After adjusting the back-focus, tighten the back-focus screw.

5) Repeat step 1)~3) until the difference between focusing position 1) and 2)becomes smallest.

CAUTION : Do not forcibly turn back-focus screw, it could cause damage to the camera.

2322

38 39

4. NAME AND FUNCTIONS

C-Mount Lens Adapter

CS-Mount Holding Screw

Used to readjust back focus of the camera. There are two back focus lock screws. These must be loosened before the camera may be back focused. Loosen the lock screws to turn the CS-mount lens adaptor, and tighten the lock screws after adjustment.

Auto Iris Lens Connector

Used to connect Auto Iris Lens plug.

Holder Screw Hole

Used to install the camera on an optional holder.(Tripod or Bracket) The optional holder must be equipped with

8 9

the screw specified as shown right.

1/4"- 20 UNC (20 THREAD) L : 4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard)

Used to attach C-mount lens.

CS-Mount Lens Adapter

Used to attach CS-mount lens.

①

Function

Setup Button

③

Power Input

Terminal

DC 12V Input Model

Class 2 Only

DC 12V

POWER

VIDEO OUT

AC 24V / DC 12V Input Model

⑤

VIDEODC

Power Indicate LED

②

Lens Selection

Swicth

④

Video Out Jack

AC 24V / DC 12V

POWER

VIDEODC

VIDEO OUT

Class 2 Only

5. OPERATING CAMERA

①

Function Setup Button

Functions can be setup using 5 buttons on the camera's rear panel.

MENU Buttons : Used to access menu mode. Also used to escape menu mode.

②

Lens Selection Switch

Used to choose DC or VIDEO or ELC according to the type of your Lens.

③

POWER Input Terminal

Used to connect an AC 24V or DC 12V power source. Used to connect a DC 12V power source.

④

VIDEO OUT Jack

Used to connect an external video monitor in jack.

⑤

Power Indicate LED

UP / DOWN Buttons : Used to choose the desired

menu item. It also moves the cursor up or down in the menu screen.

LEFT/RIGHT Buttons: Used to change the parameter of the selected menu item. It also moves the cursor the left of right in the menu screen.

LENS

SHUTTER

WHITE BALANCE

BACKLIGHT

AGC (Auto Gain Control)

DNR (Digital Noise Reduction)

SENS-UP

SPECIAL

EXIT

SETUP MENU

• MANUAL • DC/VIDEO

• ESC • MANUAL • FLK

• ATW • MANUAL • AWC

• OFF • LOW • MIDDLE • HIGH

• OFF • AUTO

• CAMERA ID • COLOR • SYNC

• MOTION DET • PRIVACY • MIRROR

• SHARPNESS • RESET • RETURN

10 11

Main Menu -

7) SENS-UP (Sense-Up)

SENS-UP makes camera's sensitivity up so you can get a bright, clear screen image by automatically detecting changes in the level of light in low light level conditions.

24 25

Menu [SPECIAL]-

26 27

SENSE-UP

①

󰼿

Press the MENU button to display the SETUP menu and move the arrow indicator to 'SENS-UP' using the

UP or DOWN button.

②

󰼿SET 'SENS-UP' to the desired mode using the LEFT or RIGHT button.

SETUP

AUTO : When your

camera is under night or low-lighting level. Select this mode.

OFF : Deactivation

NOTE

LENS SHUTTER WHITE BAL. BACKLIGHT AGC DNR

SENS-UP

SPECIAL EXIT

If you press MENU button at 'AUTO' menu, you can control the lowlight action maximum magnifications. (x2~x128)

Expander the magnifications, you can get the brighter screen as well as the afterimage. When increasing the magnifications in case of SENS-UP activated.

It may appear noise, spots, whitish, This is not out of order.

--AWC HIGH OFF

---

CAMERA ID (2)

NOTE

③

󰼿Press the MENU button to access the SETUP mode.

④

󰼿You can enter up to 15 characters.

• Move the cursor to character-enter location by using the LEFT or RIGHT button.

• Select the desired character by using the UP or DOWN button.

• Press the MENU button to confirm the blinking character. The first character is saved and the cursor in the bottom of the screen moves to the next position.

• Repeat steps a, b and c until you create the full name you want.

• Select the position at which the CAMERA ID will be located on the screen.

- Move the cursor to 'POS' and press the MENU button.

• When completed, move the cursor to 'END' and press the MENU button.

NOTE

If the CAMERA ID feature is set to 'OFF', the name will not displayed in the monitor.

Select the position by using the 4-directional buttons, then press the MENU button to confirm the position.

CAMERA ID

ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz

-. 0123456789

←󰼿󰼿󰼿→󰼿󰼿󰼿

CLR POS END

_______________

If you make a mistake while entering name Move the cursor to 'CLR', press 'SET' button. After erasing the character from right to left. Correct the character again.

Menu [SPECIAL]-

8) SPECIAL

①

󰼿

Press the MENU button to display the SET UP menu and move the arrow indicator 'SPECIAL' using the UP or DOWN button.

②

󰼿SET 'SPECIAL' to the desired mode using the LEFT or RIGHT button.

SETUP

LENS SHUTTER WHITE BAL. BACKLIGHT AGC DNR SENS-UP

SPECIAL

CAMERA ID

①

󰼿

Press the MENU button to display the SETUP menu and move the arrow indicator to 'CAMERA ID' using the UP or DOWN button.

②

󰼿SET 'ON' using the LEFT or RIGHT button.

EXIT

CAMERA ID

COLOR SYNC MOTION DET PRIVACY MIRROR SHARPNESS RESET RETURN

SPECIAL

--AWC HIGH OFF

---

--INT OFF OFF OFF ON

Menu [SPECIAL]-

COLOR

: You can choose color and B/W mode electronically.(OPTION)

①

󰼿Press the MENU button to display the setup menu and move the arrow indicator to 'COLOR' using the

UP and DOWN button.

②

󰼿SET 'COLOR' to the desired mode using the LEFT or RIGHT button.

SPECIAL

ON : Color mode

AUTO : Generally color

mode, B/W mode in low luminance.

CAMERA ID

COLOR

SYNC MOTION DET PRIVACY MIRROR SHARPNESS RESET RETURN

--INT OFF OFF OFF ON

CAMERA ID (1)

COLOR

8. CONNECTIONS

Lens Connector

When using an auto-iris lens, install the accessory lens plug on the lens cable as follows.

Connect the video output of the camera to the video input of a monitor or other equipment. When using a "loop through" connection of two or more monitors, set the 75Ω switch of only the final monitor to on. Determine the type of cable according to the distance of the connected equipment.

Video Type lens : Set lens Switch to Video. Connect the lens cable of a video Type lens.

If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.

DC type lens : Set lens switch to DC. Connect the lens cable of a DC(Galvanometric) type lens.

If the plug on the cable is a different type, replace it with the provided 4-pin iris plug.

Pin Assignment :

NOTE

VIDEO Iris Type Lens

Pin No.

#1 #2 #3 #4

After installing the connector plug, connect it to

the lens connector on the rear panel of camera.

Signal

+9V DC

Video(1.0Vp-p, high impedance, no sync)

N.C

GND

DC Iris Type Lens

Pin No.

Signal

Damping coil (-)

Damping coil (+)

Drive coil (+)

Drive coil (-)

To Power input terminal

Power Source

DC 12V

NOTE

Do not turn any component's power on until all connections are completed.

DC 12V

POWER

VIDEODC

CONTROL

VIDEO OUT

Class 2 Only

To Video input connector

40 41

Signal System

Image Sensor

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Horizontal Resolution

Min. Illumination (F1.2)

Lens Mount

Electronic Shutter

White Balance

Back Light Compensation

9. SPECIFICATIONS

High ResolutionMODEL

NTSC PAL

2:1 Interlace Transfer 1/3 Inch Super HAD CCD

768 (H) x 494 (V) 752 (H) x 582 (V)

Composite: 1.0Vp-p, 75Ω, Unbalanced

Internal Sync

More than 50dB (AGC OFF)

530 TV Lines

0.1 Lux (30IRE, AGC ON), 0.0008Lux (DSS x128)

C/CS Mount

Auto / Manual / Flickerless

x128~1/60~1/120,000 Sec.[NTSC], x128~1/50~1/120,000 Sec.[PAL]

ATW (1,800˚K~10,500˚K) / AWC / MANUAL

OFF / LOW / MIDDLE / HIGH

Auto Gain Control

DNR

Color (D&N)

Motion Detection

Privacy

Mirror

Sharpness

Applicable Lens

Supply Voltage

Power Consumption

Operating Temperature

Storage Temperature

External Dimensions

Weight

-10℃~+50℃󰼿(Recommendation:-5℃~+40℃)

65(W)x59.6(H)x122.5(D)mm / 59(W)x58(H)x123.75(D)mm

DC 12V Input Model

OFF / LOW / MIDDLE / HIGH

ON / OFF

ON / OFF (4 Programmable Zone)

ON / OFF (Horizontal)

ON / OFF (Level Adjustable)

DC Iris / Video Iris / Manual Lens

DC 12V(10V~15V)

180mA / 2.2W (Max)

-20℃~+60℃

Approx. 340g

4342

Setting up the Menu

1. Press the MENU button to access the SETUP mode.

POWER

DC 12V

VIDEODC

VIDEO OUT

Class 2 Only

SETUP

- Press the MENU button to access the setup mode.

• Select the status using the ◀, ▶, ▲, ▼ button.

• Move the cuser to character enter location by using the button.

Use five buttons on rear side of the camera.

- DOWN Button

- UP Button

- LEFT Button

- RIGHT Button

- MENU(SET) Button

SETUP

LENS

SHUTTER WHITE BAL. BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT

MANUAL ESC ATW OFF LOW LOW OFF

12 13

Main Menu -

1) Setting up the LENS

Select the lens pressing the RIGHT button.

14 15

LENS

①

󰼿On the SETUP menu screen, move the arrow indicator to the lens using the UP or DOWN button.

②

󰼿Select the desired feature using the LEFT or RIGHT button.

SETUP

LENS

SHUTTER WHITE BAL. BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT

LENS

SHUTTER WHITE BAL. BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT

SETUP

MANUAL FLK AWC HIGH OFF

---

--AWC HIGH HIGH LOW AUTO

• SETUP menu is displayed on the monitor screen.

LENS

SHUTTER WHITE BAL. BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT

2. Select the desired feature using the UP or DOWN button.

• Each time you press the UP or DOWN button, the arrow indicator moves UP or DOWN.

• Move the arrow indicator the desired feature item.

3. Change the status of the selected feature using the LEFT or RIGHT button.

• If you Press RIGHT or LEFT button, it appears available status. Press the button when gets desired feature.

4. When completed, move the arrow indicator to 'EXIT' and press the MENU button.

NOTE

You can access submenu using MENU button. For the mode with '---', you may not access submenu.

BRIGHTNESS 25

Press SET to Return

When DC LENS selected, press MENU button to control the BRIGHTNESS.

AUTO IRIS LENS(DC TYPE)is recommended than MANUAL LENS. Some lens can make a malfunction according to the BRIGHTNESS LEVEL.

SETUP

Main Menu -

Brightness

Main Menu -

--AWC HIGH HIGH LOW AUTO

SETUP

SHUTTER SPEED CONTROL(1)

Menu [SPECIAL]-

SYNC

①

󰼿Press the MENU button to display the setup menu and move the arrow indicator to 'SYNC' using the

UP and DOWN button.

②

󰼿SET to the desired mode using the LEFT or RIGHT button.

NOTE

SYNC

: Two Synchronization modes are available Internal and External Line-Lock. In Line-Lock mode, it synchronous the video signal between cameras without a synchronous generator. The line-lock synchronization is only used in the area of 60Hz(NTSC Type)/ 50Hz(PAL Type)

INT : Internal synchronization

L/L : If you choose 'L/L', you can adjust the desired phase.

- Press the MENU button.

- You can adjust the desired phase from 0 to 359.

When it used in AC power, L/L mode can be used.

In DC12V, the SYNC menu sets 'INT' mode.

CAMERA ID COLOR

SYNC

MOTION DET PRIVACY MIRROR SHARPNESS RESET RETURN

SPECIAL

--INT OFF OFF OFF ON

Menu [SPECIAL]-

MOTION DET

: Whenever your camera detects motion of object displaying 'MOTION DETECTED' with the number counted up on the screen

①

󰼿

Press the MENU button to display the setup menu and move the arrow indicator to 'MOTION DET' using the UP and DOWN button.

②

󰼿SET 'MOTION DET' to the desired mode using the LEFT or RIGHT button.

SPECIAL

OFF : Deactivation.

ON : MOTION DET.

Activated

- Press MENU button.

- Move the arrow indicator to 'AREA SET' using UP and DOWN button, and

then press the MENU button.

- Set the areas you want to observe.

CAMERA ID COLOR SYNC

MOTION DET

PRIVACY MIRROR SHARPNESS RESET RETURN

MOTION DETECTION

AREA SEL

AREA STATE TOP DOWN LEFT RIGHT

Press SET to Return

--INT OFF OFF OFF ON

AREA1 ON

MOTION DETECTION

10 25 20 40

28 29

MOTION DETECTION

AREA SEL

AREA STATE

TOP DOWN LEFT RIGHT

Press SET to Return

③

󰼿Please adjust the size of the area to be observed by using the UP, DOWN, LEFT or RIGHT button.

Max Min

AREA1 ON

10 25 20 40

Menu [SPECIAL]-

PRIVACY

: To conceal the areas you do not wish to appear on the screen.

①

󰼿Press the MENU button to display the setup menu and move the arrow indicator to 'PRIVACY' using the

UP and DOWN button.

②

󰼿SET 'PRIVACY' to the desired mode using the LEFT or RIGHT button.

OFF : Deactivation

ON : PRIVACY mode

activated

- Press the MENU button.

- Move the arrow indicator to area you want to mask.

- Set 'ON' using LEFT or RIGHT button.

- Press the MENU button and then set the area's bounds with the method like MOTION DET. Set

CAMERA ID COLOR SYNC MOTION DET

PRIVACY

MIRROR SHARPNESS RESET RETURN

SPECIAL

--INT OFF OFF OFF ON

PRIVACY

3130

Signal System

Image Sensor

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Horizontal Resolution

Min. Illumination (F1.2)

Lens Mount

Electronic Shutter

White Balance

Back Light Compensation

9. SPECIFICATIONS

High ResolutionMODEL

NTSC PAL

2:1 Interlace Transfer 1/3 Inch Super HAD CCD

768 (H) x 494 (V) 752 (H) x 582 (V)

Composite: 1.0Vp-p, 75Ω, Unbalanced

Internal Sync / Line-Lock Sync

More than 50dB (AGC OFF)

530 TV Lines

0.1 Lux (30IRE, AGC ON), 0.0008Lux (DSS x128)

C/CS Mount

Auto / Manual / Flickerless

x128~1/60~1/120,000 Sec.[NTSC], x128~1/50~1/120,000 Sec.[PAL]

ATW (1,800˚K~10,500˚K) / AWC / MANUAL

OFF / LOW / MIDDLE / HIGH

. Memo

Auto Gain Control

DNR

Color (D&N)

Motion Detection

Privacy

Mirror

Sharpness

Applicable Lens

Supply Voltage

Power Consumption

Operating Temperature

Storage Temperature

External Dimensions

Weight

AC 24V / DC 12V Input Model

OFF / LOW / MIDDLE / HIGH

ON / OFF

ON / OFF (4 Programmable Zone)

ON / OFF (Horizontal)

ON / OFF (Level Adjustable)

DC Iris / Video Iris / Manual Lens

AC 24V (20V~28V) or DC 12V (10V~15V)

330mA / 4W (Max)

-10℃~+50℃󰼿(Recommendation:-5℃~+40℃)

-20℃~+60℃

65(W)x59.6(H)x122.5(D)mm / 59(W)x58(H)x123.75(D)mm

Approx. 340g

4544

4746

CNB G1960P User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual