CNB D2810PVF User Manual
COMPOSITION:
Service Monitor Cable
Owner's Manual
INSTALLATION:
Stick the guide pattern on the
1
wall or ceiling.
Drill four holes according to
2
the guide pattern then insert
anchors into the drilled holes.
Draw out power / video wires
3
to the connecting places.
Fixed the camera to a celling
4
using four screws.
Adjust desired focus and scene
5
by turning and moving the
3-axis camera bracket by hand.
Put the dome cover over the
6
base.
Fix the dome cover on the base
7
by covering.
You must be fully aware of all the distinctive
features and precautions related to this
camera before installing it.
Guide Pattern
Mounting Screw
Ceiling
Guide Pattern
Dome Base
Mounting
Screw
Dome Cover
NOTE
Insert coin to the side
hole and remove the
dome cover by twist coin.
Simple to install
3-Axis bracket makes
adjustment easy.
SPECIFICATIONS:
Model
Signal System
Scanning System
Scanning Frequency (H
Scanning Frequency (V
Image Sensor
Total / Effective Pixels No.
S / N Ratio
Resolution
Video Output Level
Lens
Focus
Sync. System
Sensitivity (F1.2)
Electronic Shutter
White Balance
AGC/ BLC/ D&N/ FL
DSS
D-ZOOM
DNR
Input / Output Connector
Operrating Temperature
Storage Temperature
Power Consumption
(Option : AC 24V/DC 12V)
Dome Size (Ø
Weight
)
)
)
The 3D bracket (Pan, Tilt and Horizontal)
allows the camera to be manually as well
as moved horizontally and vertically.
NTSC PAL
NTSC : 525 Lines PAL : 625 Lines
15.734kHz 15.625kHz
59.94Hz 50Hz
410K 470K
Fixed Lens (f=2.45mm, 3.8mm, 6mm Selectable)/ Vari-focal Lens
0.3 Lux (color)/ 0.1 Lux (B/W) / 0.008 Lux (DSS On, x32)
1/60 ~ 120,000 Sec. 1 /50 ~ 120,000 Sec.
DC 12V (DC 9.6V~13.2V) / 150mA (Max)
AC 24V (20V~28V) or DC 12V (10V~15V), 3W (Max)
2 : 1 Interlace
1/3 inch SONY IT CCD
50dB Min. (AGC Off)
550 TV Lines
1.0 Vp-p (75 Ohms, composite)
Manual
Internal
Auto
On / Off Selectable
Max 32 times
2 x
AUTO
Power, Video, UTP (Option)
-10°C ~ 45°C
-20°C ~ 65°C
100mm
Approx. 366g
s
t
a
n
i
l
l
s
e
n
i
L
V
T
SDNR
SDNR
0
5
5
•
Super
Super
Digital
Digital
Noise
Noise
R
eduction
R
eduction
o
•
S
u
p
e
r
D
i
g
i
t
a
l
N
o
i
s
e
R
e
d
u
c
t
i
o
n
t
e
l
p
m
i
S
•
.
y
s
a
e
t
n
e
m
t
3
A
x
i
s
b
r
a
c
k
e
t
m
a
k
e
s
s
a
u
j
d
CCD CameraColor Dome
Digital DSP
Digital Slow Shutter DSS
ver.0605E
P/N:3810-0072C
Color Dome
3-Axis
.Vari-focal
LENS
.Fixed Lens
Design and specifications are
subject to change without notice.
1/3" SONY CCD
PRECAUTIONS:
Do not install the camera in extreme
!
temperature conditions.
Do use the camera under conditions where
temperatures are within -10°C to 45°C.
Be especially careful with ventilation under
high temperatures.
Do not install or use the camera in an
!
environment where the humidity is high.
It can cause the image quality to be poor.
Do not disassemble the camera.
!
There are no user-serviceable parts inside it.
Do not drop the camera or subject
!
them to physical shocks.
It can cause malfunctions to occur.
Do not expose the camera to rain or
!
spill beverage on it.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode
the electronic components.
Note
!
If the camera is exposed to spotlight or
object reflecting the strong light, smear
or blooming may occur. Please check the
power whether it satisfies the normal
specification before connecting the camera.
1
Tilt rotation: Adjusting the vertical angle.
2
Pan rotation: Adjusting the horizontal angle.
3
Horizontal rotation: Adjusting the horizontal
position of the screen.
NAME AND FUNCTION:
Fixed Lens Type
1
2
Vari-focal Lens Type
4
5
2
Camera Lay-out
4
Focus handle: Focus (Far or Near)
5
Zoom handle: Zoom (Tele or Wide)
90º
CONNECTION:
Connecting to Monitor and Power
Built-in camera
bracket will make user
much easier to rotate in
any direction.
3-axis
360º
DC 12V Power Type
• The wire is polarized.
• Use DC 12V power source.
#
#
1
2
No.
#1
#2
Function
Video Output
Power Input
3
Video
(Yellow)
Power - DC 12V
(Red)
Terminal Color
Yellow
Red
DC 12V(DC9.6V~13.2V), 150mA(Max)
Video Output
GND
Remark
1.0 Vp-p
AC 24V/DC 12V Power Type
• The wire is non-polarized.
• Use AC 24V power source or
CAMERA SET-UP:
Vari-focal Lens Type
a
Service Monitor Connecter:
Use service monitor connector
to set camera angle & focus
when installing.
a
05
5
J
ER
O
T
I
A
E
H
/AUD
(AC 24V)
J503
BLC ON
VIDEO
ON
DC LEVEL
b
AGC OFF
D/N OFF
21 43 65
J502
AC24V
J501
DSS OFF
D/Z ON
FL ON
c
b
DC Level Adjustment V.R
c
Function Selection Switch:
•
BLC(Back Light Compensation)
ON/OFF
•AGC(Auto Gain Control) ON/OFF
•D/N(Day & Night) ON/OFF
•
DSS(Digital Slow Shutter) ON/OFF
•D/Z(Digital Zoom) ON/OFF
•FL(Flickerless) ON/OFF
CAUTION
the switching of D&N doesn't work.
Because the D&N switching function
is related in AGC level.
: In case of AGC off,
DC 12V power source.
#
1
1
Video
(Yellow)
3
#
2
No.
Function
#1
Video Output
#2
Power Input
IR LED
Power - AC 24V/ DC 12V
(Green)
Terminal Color
Yellow
AC24V(20V~28V)orDC12V(10V~15V), 3W(Max)
Green
(3.8mm Fixed Lens Only)
Video Output
GND
Remark
1.0 Vp-p
: Option
• Power Consumption: 5W
• IR LED Specification: 850nm / 30° (24EA)
TROUBLESHOOTING:
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
The image does not
appear on the screen.
The image on the
screen is dim.
The camera does not work
properly, the surface of the
camera case is hot, and a black
line appears on the screen.
The screen blinks a lot.
Check the power source for the monitor and camera
and assure that the voltage and polarity are properly
connected and being supplied correctly.
Check if the lens is stained. If dirty, clean the lens with
a soft, clean cloth.
Adjust the Back Focus of the lens again.
Check if you have connected the camera to a proper
power source and If there is no problem with the power,
turn the unit off immediately and seek assistance from
our After Service department.
Check if the camera is pointed toward the sun or a
fluorescent lamp.
Adjust the angle or location of the camera if too much
light is coming into the screen.
360º
Loading...