1
VER0220094800
HIGH DEFINITION DIGITALE
SATELLITE-RECEIVER
DVB 4800
Fig. 1.1: DVB 4800 (Symbol picture)
USER MANUAL
General
- 2 -
Imprint
All rights reserved. Any reproduction without consent of cmx® is
prohibited.
cmx® reserves the right to modifications of the device.
Designed by cmx® in Europe | Assembled in China
TM©2009 cmx electronics
General
- 3 -
CONTEXTS
1. GENERAL ...................................................................................... - 4 -
1.1. Safety precautions ................................................................. - 4 -
1.2. Disposal of waste electronic equipment ................................ - 4 -
1.3. Battery disposal ..................................................................... - 4 -
1.4. Copyright ............................................................................... - 5 -
1.5. Hearing protection ................................................................. - 5 -
1.6. Cleaning and maintenance .................................................... - 5 -
2. FEATURES ..................................................................................... - 5 -
3. LOCATION OF CONTROLS ................................................................ - 6 -
3.1. Main unit - front ...................................................................... - 6 -
3.2. Main unit - rear ...................................................................... - 7 -
3.3. Remote control ...................................................................... - 8 -
4. PREPARATION ............................................................................... - 9 -
4.1. Connection the system .......................................................... - 9 -
4.1.1. Connection with SCART cable ..................................... - 10 -
4.1.2. Connection with HDMI cable ........................................ - 10 -
4.1.3. Connection with component cable ............................... - 11 -
4.2. Connect to hi-fi system ........................................................ - 11 -
4.3. Connect to digital audio amplifier ........................................ - 11 -
4.4. Insert batteries ..................................................................... - 12 -
5. START OF OPERATION AND CONFIGURATION .................................. - 12 -
5.1. Start of operation ................................................................. - 12 -
5.2. General operation ................................................................ - 13 -
5.3. Configuration ....................................................................... - 14 -
5.3.1. Edit channel list .......................................................... - 15 -
5.3.2. Installation ................................................................... - 17 -
5.3.3. System setting ............................................................ - 19 -
5.3.4. Setting .......................................................................... - 21 -
5.3.5. Games .......................................................................... - 23 -
5.3.6. External memory ........................................................ - 23 -
6. TROUBLESHOOTING ..................................................................... - 24 -
7. WARRANTY ................................................................................. - 25 -
7.1. Warranty procedure ............................................................. - 26 -
7.2. Warranty has expired .......................................................... - 26 -
7.3. Shipping the unit .................................................................. - 26 -
8. TECHNICAL SPECIFICATIONS ......................................................... - 30 -
General
- 4 -
1. General
1.1. Safety precautions
Only connect to mains power supply (230 Volt/50 Hz).
Do not place containers filled with water on top of the device.
Do not place device in close proximity of water (e.g. sink, wash basin,
etc.). The device can fall into the water and cause a short circuit.
The device consumes some power during standby operation. For zero
power consumption disconnect from mains power supply.
During a thunderstorm disconnect the receiver from mains power supply
and disconnect the LNB cable to the satellite dish.
Place the device on a stable surface to prevent it from tipping over and
causing damages or injuries.
Condensation can form if the device is placed in cold surroundings. Leave
the device for at least one hour in standby mode.
Keep at least 10 cm distances at top and rear and 5cm at the sides for
proper ventilation to avoid overheating.
Do not subject the device to direct sunlight or high temperatures, this can
result in fire.
1.2. Disposal of waste electronic equipment
Your product is manufactured from high quality raw materials and should be
recycled.
Ask your municipality for collecting points for waste electronic
equipment.
Do not dispose of old appliances with the household waste.
The symbol on the product, the instructions for use or the packing
will advert about the methods for disposal.
1.3. Battery disposal
The law requires returning exhausted batteries to public collection points or the
dealer.
Do not dispose of exhausted batteries with the household waste.
Features
- 5 -
1.4. Copyright
It is illegal to copy, send, exhibit, broadcast via cable, publicly show or rent
copyrighted materials without consent.
1.5. Hearing protection
Select a moderate volume to protect your hearing.
Only turn the volume to a level where you can still hear ambient noise.
1.6. Cleaning and maintenance
Before cleaning disconnect from mains power supply.
Do not clean with liquid cleaning agents or a wet cloth, this can cause
a short circuit.
Cleaning the casing
Clean the casing with a dry cloth.
2. Features
This satellite receiver DVB 4800 allows you to receive and playback free-to-air
not encrypted channels with a CI module (common interface) and
corresponding CAM card (smart card).
CI-Module and CAM card are not including in delivery and in
specialized traders available.
Location of controls
- 6 -
3. Location of controls
3.1. Main unit - front
Fig. 3.1: front DVB 4800 (Symbol picture)
1
STANDBY
On/off
2 VFD Display
3 POWER LED for operation
4 VOL- Decrease volume / cursor left
5 VOL+ Increase volume / Cursor right
6 ▲CH + Channel changing / next channel
7 OK Confirm the range
8 MENU Menu button
9 ▼CH - Channel changing / previous channel
10 USB Port for MP3 player / USB stick
11 CI Port for Smart card
Location of controls
- 7 -
3.2. Main unit - rear
Fig. 3.2: rear DVB 4800 (Symbol picture)
1 LNB IN SAT antenna input (75 Ω input)
2 VCR SCART in-/output for A/V-recorder
3 TV SCART output for TV
4 HDMI HDMI Digital Audio/Video output
5 YPbPr Component output
6 100-240V~ Power cable
7 ON/OFF Power switch
8 L / R 2 channel audio output
9 COAXIAL coaxial digital audio output
Location of controls
- 8 -
3.3. Remote control
Fig. 3.3: infrared remote control DVB 4800 (Symbol picture)
1 STANDBY On/off
2 MUTE Mute the sound
3 0 - 9 numbers / digit entry (A-Z); 0; Sleep timer
4 TV / SAT Toggle between TV/SAT
5 VOL -/+ Decrease volume / increase volume
6 P- / P+ By activated program list: changing between program lists
7 EXIT Menu exit / flashes fade out
8 ► Cursor button, Normal mode: increase volume
9 EPG Electronic program guide
10 TIMER Timer / function button BLUE
11 YELLOW Function button YELLOW
12 FIND Program search by name
13 AUDIO Select audio track
14 PVR For recording and playback
15 SUBT Subtitle disable/enable (if sent)
Preparation
- 9 -
16 INFO Accessing program parameters
17 GREEN Function button GREEN
18 V-FMT Changing size of picture / function button RED
19 FAV Favourite lists indicate
20 ▼ Cursor button/ Normal mode: channel change
21 ◄ Cursor button, normal mode: decrease volume
22 OK Confirm the range
23 TEXT View teletext (switch transparent)
24 ▲ Cursor button, normal mode: channel change
25 MENU Menu button
26 RECALL Previous program
27 CH -/+ Previous program /next program
28 TV/ RAD Toggle between TV/RADIO
4. Preparation
4.1. Connection the system
Follow these steps to connect the system:
Ensure that all units are turned off when connecting.
To avoid image interference only connect the satellite receiver via a
video connection to your TV set.
1. Connect the mains power cable to a wall outlet.
2. Connect the TV with the receiver.
Scart, HDMI, RCA, component, 2-channel or coax cable are not
supplied.
You can connect the satellite receiver in several modes to TV set,
recording device (e.g. VCR) and other devices. Find details in chapter
4.1.1.
Heed the user manuals for your TV set ant the other devices.
Preparation
- 10 -
4.1.1. Connection with SCART cable
1. Connect the SCART cable into
the SCART jack “TV” on the
receiver.
2. Connect the SCART cable with
the TV.
3. To connect video devices
connect a scart cable to the
receiver’s “VCR” scart
connector.
To connect hi-fi systems connect
the RCA cable to the receiver’s
„AUDIO R“ and „AUDIO L“
connectors.
4.1.2. Connection with HDMI cable
1. Connect the HDMI cable into the HDMI jack “HDMI” on the receiver.
2. Connect the HDMI cable with the TV.
3. To connect video devices connect a scart cable to the receiver’s
“VCR” scart connector.
4. To connect hi-fi systems connect
the RCA cable to the receiver’s
„AUDIO R“ and „AUDIO L“
connectors
Simultaneous operation of the
receiver via SCART and HDMI
connectors is not possible. You
have a signal either on the
SCART or the HDMI output.
Playback from a video device
connected to “VCR SCART” via
the HDMI connector is not
possible.
Fig. 4.1: Connection with scart
cable
Fig. 4.2: Connection with HDMI
cable
Loading...