CMP T3CDSX User Manual

DUBAI • HOUSTON • NEWCASTLE • SINGAPORE • SHANGHAI • PUSAN • PERTH

TECHNICAL DATA

CABLE GLAND TYPE : T3CDSX
INGRESS PROTECTION : IP66, NEMA 4X, DELUGE TO DTS01-01, Oil Resistan
PROCESS CONTROL SYSTEM : BS EN ISO 9001

: ISO/IEC 80079-34:2011

INSTALLATION INSTRUCTIONS FOR
INSTALLATION OF CMP CABLE

HAZARDOUS AREA CLASSIFICATION

ATEX CERTIFICATION No : SIRA 06ATEX1283X & SIRA 06ATEX4328X
ATEX CERTIFICATION CODE : II 2 GD Ex d IIC / Ex e II / Ex nR II / Ex tD A21 IP66
IEC Ex CERTIFICATION No : IEC Ex SIR.07.0005X
IEC Ex CERTIFICATION CODE : Ex d IIC / Ex e II / Ex nR II / Ex tD A21 IP66
CSA-US CERTIFICATION No : CSA.02.310517X
CSA-US CERTIFICATION CODE : Class I, Div 2, Groups ABCD; Class II, Div 2, Groups EFG; Class III; Ex d IIC; Ex e II;

UL CERTIFICATION FILE : E200163
UL CERTIFICATION CODE : Class I, Zone 1, AEx II; TYPE 4X, OIL RES II

INSTALLATION INSTRUCTIONS

Installation should only be performed by a competent person using the correct tools. Read all instructions before beginning installation.

SPECIAL CONDITIONS FOR SAFE USE

1. The glands ranges shall only be used on enclosures where the temperature, at the point of mounting, is in the range -60°C to +130°C.

2. When used with braided cable, the cable glands shall be used for fixed installations only. Cables must be effectively clamped to prevent twisting
and pulling.

3. When used in Group I applications, the equipment must only be mounted where the risk of mechanical impact is low.

4. According to CEC Wiring methods, connectors with Metric entry threads are only suitable for Areas classified in ZONES unless fitted with an
approved Metric to NPT thread conversion adaptor.

ACCESSORIES

The following accessories are available from CMP Products, as optional extras, to assist with fixing, sealing and earthing :-

Locknut | Earth Tag | Serrated Washer | Entry Thread (I.P.) Sealing Washer | Shroud *

Cable
Gland

20S/16 M20 1/2" 3/4" 15.0 3.2 8.7 6.1 13.4 0.15 0.5 24.0 25.9 70.0 20S16T3CDSX1RA 0.170

* For IP67 & IP68 requirements the Cable Diameter “B” (minimum value) shown above should be increased by 1.0 mm to ensure complete compliance

Available Entry Threads

ize

S

20S M20 1/2" 3/4" 15.0 6.1 11.7 9.5 15.9 0.15 0.5 24.0 25.9 70.0 20ST3CDSX1RA 0.170

20 M20 1/2" 3/4" 15.0 6.5 14.0 12.5 20.9 0.2 0.5 30.5 32.9 72.0 20T3CDSX1RA 0.256

25S M25 3/4" 1" 15.0 11.1 20.0 14.0 22.0 0.2 0.6 37.5 40.5 82.0 25ST3CDSX1RA 0.384

25 M25 3/4" 1" 15.0 11.1 20.0 18.2 26.2 0.2 0.6 37.5 40.5 82.0 25T3CDSX1RA 0.379

32 M32 1" 1 1/4" 15.0 17.0 26.3 23.7 33.9 0.2 0.6 46.0 49.7 85.0 32T3CDSX1RA 0.560

40 M40 1 1/4" 1 1/2" 15.0 23.5 32.2 27.9 40.4 0.2 0.8 55.0 59.4 86.0 40T3CDSX1RA 0.848

50S M50 1 1/2" 2" 15.0 31.0 38.2 35.2 46.7 0.2 0.8 60.0 64.8 98.0 50ST3CDSX1RA 1.055

50 M50 2" 2 1/2" 15.0 35.6 44.1 40.4 53.1 0.3 0.8 70.0 75.6 100.0 50T3CDSX1RA 1.521

63S M63 2" 2 1/2" 15.0 41.5 50.0 45.6 59.4 0.3 0.8 75.0 81.0 108.0 63ST3CDSX1RA 1.750

63 M63 2 1/2" 3" 15.0 47.2 56.0 54.6 65.9 0.3 0.8 80.0 86.4 103.0 63T3CDSX1RA 1.685

75S M75 2 1/2" 3" 15.0 54.0 62.0 59.0 72.1 0.3 0.8 89.0 96.1 105.0 75ST3CDSX1RA 2.345

75 M75 3" 3 1/2" 15.0 61.1 68.0 66.7 78.5 0.3 0.8 99.0 106.9 114.0 75T3CDSX1RA 3.200

90 M90 3" 3 1/2" 15.0 66.6 79.3 76.2 90.4 0.4 0.8 114.0 123.1 140.0 90T3CDSX1RA 5.100

100 M100 4" 4 1/2" 15.0 76.0 91.0 86.1 101.5 0.4 0.8 123.0 132.8 170.0 100T3CDSX1RA 6.500

115 M115 4 1/2" 5" 15.0 86.0 98.0 101.5 110.3 0.4 0.8 133.4 144.1 210.0 115T3CDSX1RA 7.000

130 M130 5" 6" 15.0 97.0 115.0 114.2 123.3 0.4 0.8 146.1 157.8 250.0 130T3CDSX1RA 7.800

I, The undersigned, hereby declare that the equipment referred to herein conforms to the requirements of the ATEX Directive 94/9/EC and the following

Standard Option

etricNPT

M

standards:-

PT

N

Class I, Zone 1, AEx d IIC; Class I, Zone 1, AEx e II

Minimum

hread

T
Length

Cable

Bedding

Diameter

MinMaxMinM

Dimensions are displayed in millimetres unless otherwise stated

Overall Cable

Diameter

ax

M

Braid Wire

Diameter

in

M

ax

Across

Flats

ax

M

Across

Corners

ax

M

Protrusion

Length

Ordering Reference

(Brass Metric)

Cable
Gland

Weight

(Kgs)

GLAND TYPES T3CDSX

CABLE GLAND FOR USE WITH WIRE BRAID, STRIP, AND TAPE ARMOUR FOR USE IN HAZARDOUS
LOCATIONS.

INCORPORATING EC DECLARATION OF CONFORMITY TO DIRECTIVE 94/9/EC

M

CMP TRITON

T

CDS

COMPENSATING DISPLACEMENT SEAL SYSTEM.

Cable Gland Selection Table

LISTED MARINE
SHIPBOARD CABLE
FITTING
31YM

M

T

DELUGE PROOF CABLE GLAND FEATURING

CABLE GLAND

CABLE GLAND

TYPE T3CDSX

TYPE T3CDSX

CMP Document No. FI409 Issue 4 01/13

EN60079-0:2006, EN60079-1:2007, EN60079-7:2007, EN60079-15:2005, BS 6121:1989, EN50262:19989 (Amd 2001), EN61241-0:2004, EN61241-1:2004

Dr Geof Mood - Technical Director - (Authorised Person)

Glasshouse Street • St. Peters • Newcastle upon Tyne • NE6 1BS

Tel: [phone] • Fax: [phone]

0518

Notified Body: Sira Certification Service, Rake Lane, Chester CH4 9JN, England.

E-Mail: [e-mail] • Web: www.cmp-products.com

www.cmp-products.com

Logo’s shown for illustration purposes only. Please check certification for details

DUBAI • HOUSTON • NEWCASTLE • SINGAPORE • SHANGHAI • PUSAN • PERTH

www.cmp-products.com

INSTALLATION INSTRUCTIONS FOR CMP CABLE GLAND T3CDSX

CABLE GLAND COMPONENTS

1. Entry Item

2. Body

3. Compensating Sleeve

4. Armour Cone

5. AnyWay Clamping Ring

6. Outer Seal Nut

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION

SUB-ASSEMBLY A

ITEM 4

ITEM 5 SUB-ASSEMBLY B

4321 65

4. Pass the cable through sub-assembly A, spacing the braid evenly around the cone. Whilst
continuing to push the cable forward to keep the cable braid in contact with the cone, tighten the
compensating sleeve (3) into the entry component (1) until all the threads are used. (Note that the
internal compensator will prevent the cable gland inner seal from being over-tightened onto the
cable inner sheath.)

5. Terminate the cable by tightening the body (2) onto the entry component (1) using a spanner on
each part. Tighten the body until the body and entry components are metal to metal and cannot
be tightened further.

“CDS” INNER SEAL

HOUSING

DELUGE

SEAL

BRAID
CONE

ANYWAY

CLAMPING RING

BODY AND OUTER

SEAL NUT

1. Separate the gland into two sub-assemblies, A and B, by unscrewing the body (2) from the entry
item (1). Note that items (4) and (5) are loose items.

2. Prepare the cable by stripping back the cable outer sheath and armour to suit the equipment
geometry. Expose the braid by stripping back the outer sheath further using the table below as a
guide.

Cable Strip
Length “L”

CABLE GLAND SIZE 20S/16, 20S, 20 25S, 25, 32, 40 50S, 50, 63S, 63 75S, 75, 90, 100, 115, 130

CABLE STRIP LENGTH “L” 12mm 15mm 18mm 20mm

3. Secure the entry components (sub-assembly A) into the equipment. (Not for remote installation)
Pass the sub-assembly B and AnyWay clamping ring (5) over the cable, outer seal first.
Insert the armour cone (4) in the sub-assembly B:

6. Tighten the outer seal nut (6) until it comes to an effective stop. This will occur when:­A) The outer seal nut (6) has clearly engaged the cable and cannot be further tightened
without the use of excessive force by the installer.
B) The outer seal nut (6) is metal to metal with the body of the gland (2).

www.cmp-products.com

DUBAI • HOUSTON • NEWCASTLE • SINGAPORE • SHANGHAI • PUSAN • PERTH