CMP A2F Installation Instructions Manual

www.cmp-products.com

CABLE GLAND FOR USE WITH UNARMOURED AND BRAID ARMOURED CABLES

INCORPORATING EU DECLARATION OF CONFORMITY TO DIRECTIVE [2014/34/EU]

TECHNICAL DATA

EXPLOSIVE ATMOSPHERES CLASSIFICATION

INSTALLATION INSTRUCTIONS

Installation should only be performed by a competent person using the correct tools. Spanners shoudl be used for tightening. Read all instructions before beginning installation.

ACCESSORIES

The following accessories are available from CMP Products, as optional extras, to assist with fixing, sealing and earthing :­Locknut, Earth Tag, Serrated Washer, Entry Thread (I.P.) Sealing Washer, Shroud

CMP Products Limited on its sole responsibility declares that the equipment referred to herein conforms to the requirements of the ATEX Directive 2014/34/EU and the following
standards:-

EN 60079-0:2012, EN 60079-1:2007, EN 60079-7:2007, EN 60079-15:2010, EN 60079-31:2009, BS 6121:1989, EN 62444:2013, EN 61241-0:2004, EN 61241-1:2004

David Willcock - Certification Engineer (Authorised Person)
CMP Products Limited, Cramlington, UK, NE23 1WH
24th June 2015

CABLE GLAND

TYPE

A2F

INSTALLATION INSTRUCTIONS FOR
A2F CABLE GLAND

SPECIAL CONDITIONS FOR SAFE USE

None.

Glasshouse Street • St. Peters • Newcastle upon Tyne • NE6 1BS

Tel: [phone] • Fax: [phone]

E-Mail: [e-mail] • Web: www.cmp-products.com

Notified Body: Sira Certification Service, Unit 6, Hawarden Industrial Park, Hawarden, CH5 3US, UK

0518

CABLE GLAND TYPE : A2F
INGRESS PROTECTION : IP66 IP67, IP68, NEMA 4X
PROCESS CONTROL SYSTEM : BS EN ISO 9001

ISO/IEC 80079-34:2011

ATEX CERTIFICATION No : SIRA 13ATEX1068X, SIRA 13ATEX4074X
ATEX CERTIFICATION CODE : II 2G, II 1D Ex d IIC Gb, E x e IIC Gb, Ex ta IIIC D a

: II 3G Ex nR IIC Gc I M2 E x d I Mb, Ex e I Mb

IECEx CERTIFICATION No : IECEx SIR 13.0023X
IECEx CERTIFICATION CODE : Ex d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da, Ex d I Mb, Ex e I Mb
CSA CERTIFICATION No : 1211841
CSA CERTIFICATION CODE : Ex d IIC, Ex e II, Ex nR II, Enclosure Type 4X, Class 1, Div. 1, Div. 2, Groups B,C & D

CMP Document No. FI413 Issue 12, IEC Issue 10, CSA Issue 10

Logo’s shown for illustration purposes only. Please check certification for details

SCAN FOR INSTALLATION VIDEOS

Note: Standard Seal (Black) Temperature Range = -60°C to +130°C,
High Temperature Seal (Brown) Temperature Range = -20°C to +200°C for High Temperature Seal add ‘HT’ to Ordering Reference after Gland Type e.g. 20SA2FHT1RA.

Cable Glan d

Size

Available E ntry Thread s

(Alternate Metric Thread Lengths Available)

Overall Ca ble

Diameter

Across

Flats

Across

Corners

Protrusion

Length

Combined Ordering

Referenc e

(*Brass Metric)

Shroud

Cable

Gland Weig ht

(Kgs)

Standard Option

Metric

Thread Length

(Metric)

NPT

Thread

Length (N PT)

NPT Min Max Max Max Size Type

Ordering

Suffix

16 M16 15.0 - - - 3.2 8.7 24. 0 26.4 25.1 16 A2F 1R A PVC04 0.060

20S/16 M20 15 .0 1/2” 19.9 3/4” 3. 2 8.7 24.0 26.4 25.1 20 S16 A2F 1R A P VC04 0. 070

20S M20 15.0 1/2” 19.9 3/ 4” 6.1 11.7 24.0 26.4 25.1 20S A2F 1RA PVC04 0.06 0

20 M20 15 .0 1/ 2” 19.9 3/4” 6.5 14.0 27.0 29.7 27. 2 20 A2F 1R A PVC05 0.070
25 M25 15.0 3/4” 20.2 1” 11.1 20.0 36.0 39.6 35.5 25 A2F 1R A PVC09 0.130
32 M32 15.0 1” 25.0 1 1/4” 17. 0 26.3 41 .0 45.1 34.2 32 A2F 1R A P VC10 0.150
40 M40 15.0 1 1/4” 25.6 1 1/2” 2 3.5 32.2 50.0 55.0 35.1 40 A2F 1RA PVC13 0.200

50S M50 15.0 1 1/2” 26.1 2” 31.0 38.2 55 .0 60.5 32.0 50S A2F 1RA PVC15 0.260

50 M50 15 .0 2” 26 .9 2 1/2” 35. 6 44.0 60.0 66.0 36.3 50 A2F 1RA PVC18 0.270

63S M63 15.0 2” 26.9 2 1/2” 41 .5 49.9 70.5 77. 6 33.5 63S A2F 1R A PVC 21 0 .430

63 M63 15. 0 2 1/2” 39.9 3” 4 7.2 55.9 75.0 82.5 35 .8 63 A2F 1RA P VC23 0.40 0

75S M75 15.0 2 1/2” 39.9 3” 54.0 61.9 80.0 88.0 34.2 75S A2F 1RA PVC24 0.520

75 M75 15.0 3” 41.5 3 1/2” 61.1 67.9 8 4.0 92.4 40.6 75 A2F 1R A PVC26 0.500

90 M90 24.0 3 1/2” 42.8 4” 66.6 79.9 108.0 118.8 58.3 90 A2F 1R A PV C31 1.600
100 M100 24.0 4” 44.0 5” 76.0 91.0 123.0 135 .3 55.2 100 A2F 1RA LSF33 1.78 0
115 M115 24.0 4” 44.0 5” 86.0 9 7.9 133.4 146.7 65 .2 11 5 A2F 1RA LSF34 2.670
130 M130 24.0 5” 46.8 6” 9 7.0 114.9 15 2.4 167.6 73.9 130 A2F 1RA LSF35 3.8 00

*Note : For material option s please add the followin g suffix to change the Orde ring Reference ; Brass (n o suffix required), N ickel Plated Brass “5”, 316 Grade Stainle ss Steel “4”, Copper Free Alumi nium “1”
For NPT options ple ase add the following dig its to the material suffi x ; 1/2” = 31, 3/4” = 32, 1” = 33, 1 1/4” = 34, 1 1/2” = 35, 2” = 36, 2 1/2” = 37, 3” = 38, 3 1/2” = 39, 4” = 310 (Brass requires p refix “0”)

Examples : 32A2F1RA534 = N ickel Plated Brass 1-1/4” NPT, 50SA2F1RA035 = Bras s 1-1/2” NPT, 25A2F1RA432 = Stainless Steel 3/4” NP T, 20A2F1RA5 = Nickel Plated Brass M20

Dimensions are displayed in millimetres unless otherwise stated

www.cmp-products.comwww.cmp-products.com

INSTALLATION INSTRUCTIONS FOR CMP CABLE GLAND TYPES A2F

CABLE GLAND COMPONENTS - It is not necessary to dismantled the cable gland any further than illustrated below

1. Entry Item

2. Seal

3. Seal Nut

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION

1. It is not necessary to dismantle the gland any further than illustrated below.

3. Determine the conductor length required to suit the installation and prepare the cable accordingly, removing part of the outer sheath
where required to reveal the insulated conductors.

4. Slacken the seal nut (3) to relax the seal (2).

5. Pass the cable through the gland to the desired position, then tighten the seal nut by hand until resistance is felt (when the seal
contacts the cable). Tighten with a spanner one further turn.

2. Fit the gland into the equipment and fully tighten the entry item (1).

1. 2. 3.