Page 1
TECHNICAL DATA
Date Printed:
CABLE GLAND TYPE : 781D / 781E
INGRESS PROTECTION : IP66, 67, 68 (when fitted with CMP installation accessories)
PROCESS CONTROL SYSTEM : BS EN ISO 9001 - 2000
: ISO/IEC 80079-34:2011
EXPLOSIVE ATMOSPHERES CLASSIFICATION
ATEX CERTIFICATION No : SIRA10ATEX1307U
ATEX CERTIFICATION CODE 781D : II 2G Ex d IIC Gb, II 1D Ex ta IIIC Da
ATEX CERTIFICATION CODE 781E : II 2G Ex e IIC Gb, II 1D Ex ta IIIC Da
IECEx CERTIFICATION No : IECEx SIR.10.0149U
IECEx CERTIFICATION CODE 781D : Ex d IIC Gb, Ex ta IIIC Da
IECEx CERTIFICATION CODE 781E : Ex e IIC Gb, Ex ta IIIC Da
INSTALLATION INSTRUCTIONS
Installation should only be performed by a competant person using the correct tools. Spanners should be used for tightening. Read all instructions before beginning installation.
SPECIAL CONDITIONS FOR SAFE USE
1. When used as drain plugs the 781D or 781E must be fitted to the bottom of the enclosure.
2. The 781D can be u sed with enclos ures up to 30 litres fo r group IIB gases a nd enclosures up to 2 .5 litres for group I IC gases
3. The breather drain plug shall not be used with any form of adaptor or reducer.
4. The temperature range for these products is :- 781D: -60°C to +130°C
781E (Metal / Viton o-ring): -20°C to +130°C
781E (Metal / Silicon o-ring): -20°C to +130°C
781E (Plastic): -20°C to +105°C
SCAN FOR INSTALLATION VIDEOS
INSTALLATION INSTRUCTIONS FOR
INSTALLATION OF CMP BREATHER
DRAIN TYPE 781D & 781E
BREATHER DRAIN DEVICES FOR USE IN Ex d (781D) OR Ex e (781E) APPLICATIONS.
INCORPORATING EU DECLARATION OF CONFORMITY TO DIRECTIVE [2014/34/EU]
Product Selection Table
Ordering
Reference
(781D)
781DM2 781EM2 M20 x 1.5 15.0 12.7 30.0 33.0 7
781DM3 781EM3 M25 x 1.5 15.0 12.7 36.0 39.6 10
781DT1 781ET1 ½” N PT 19.9 12.7 30.0 33.0 7
781DT2 781ET 2 ¾” N PT 20.2 12.7 36.0 39.6 10
Materials
Order reference is for Brass.
- Add “5” at the end for Nickel Plated Brass (e.g. 781DM25)
- Add “4” at the end for stainless steel (e.g. 781EM24)
- Add “2” at the end for plastic (e.g. 781EM22) - Not available for 781D
CMP Products Limited. on its sole responsibility declares that the equipment referred to herein conforms to the requirements of the ATEX Directive 2014/34/EU and the following
standards :-
EN60079-0:2012, EN60079-1:2007, EN60079-7:2007, EN60079-15:2010, EN60079-31:2009, BS6121:1989, EN62444:2013
Ordering
Reference
(781E)
Threa d Size
Minim um Thread
Length
All dimensions sho wn are in mill imetres u nless otherw ise stated
Protrusion
Length
Across Flats
Dimension
Acros s Corners
Dimensions
Max
Installation
Torque (Nm)
TYPE
781D & 781E
BREATHER DRAIN
781E 781D
781D - Breather drain
for Ex d applications
David Willcock – Certification Engineer (Authorised Person)
CMP Products Limited, Cramlington, NE23 1WH, UK
24th June 2015
0518
Notified Body: Sira Certification Service, Unit 6 Hawarden Industrial Park, Hawarden, CH5 3US, England.
www.cmp-products.com
E-Mail: customerservices@cmp-products.co.uk • Web: www.cmp-products.com
Glasshouse Street • St. Peters • Newcastle upon Tyne • NE6 1BS
Tel: +44 191 265 7411 • Fax: +44 1670 715 646
781E - Breather drain
for Ex e applications
CMP Document No. FI427 Issue 9, IEC Issue 5 CSA Issue 9
Logo’s shown for illustration purposes only. Please check certification for details
Page 2
INSTALLATION INSTRUCTIONS FOR CMP ACCESSORY TYPES 781D & 781E
BREATHER DRAIN PLUGS
ACCESSORY COMPONENTS - It is not necessary to dismantled the breather drain any further than illustrated below
1. Body
2. Castellated Locknut (781E only)
3. Threaded Insert (781D only)
4. Felt pad
5. ‘O’ Ring Seal
2
1
Slotted
Arrangement
5
4
3
781E ONLY - THREADED ENTRY
1. Remove the castellated locknut
2. If the equipment entry is threaded, screw the breather drain body (1) into the entry hole
and tighten with a spanner. There is no need to fit the castellated locknut.
Do not disturb the felt pad (4).
4
Drainage Hole
Drainage Hole
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION
781D ONLY
Screw the breather drain body (1) into the equipment and tighten with a spanner.
Do not disturb the threaded insert (3).
This insert forms a protective flamepath and is also the drain path for any water that may get into the
equipment.
781E ONLY - CLEARANCE HOLE ENTRY
If the equipment entry is a clearance hole, then position the body (1) in the entry hole and secure using
the castellated locknut and tighten. Ensure that the nut castellations are towards the enclosure wall to
ease water drainage.
Do not disturb the felt pad (4).
www.cmp-products.comwww.cmp-products.com
Loading...