Page 1
Global LCD Panel Exchange Center
ுழၴ ຝ ᐉு ߡۥ ދป
ขጥ
楊
竣 傑
TFT LCD Approval Specification
MODEL NO.: N184H6-P02
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
Customer:
Approved by:
Note:
NB
2010-02-08
17:13:27
1 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
2010.02.08
Director Accept
Version 2.0
www.panelook.com
Page 2
Global LCD Panel Exchange Center
REVISION HISTORY --------------------------------------------------------3
1. GENERAL DESCRIPTION -------------------------------------------------------4
1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
1.5 MECHANICAL SPECIFICATIONS
2. ABSOLUTE MAXIMUM RATINGS -------------------------------------------------------5
2.1 ABSOLUTE RATINGS OF ENVIRONMENT (BASED ON CMO MODULE)
2.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL)
2.3 ELECTRICAL ABSOLUTE RATINGS (OPEN CELL)
3. ELECTRICAL CHARACTERISTICS -------------------------------------------------------7
3.1 TFT LCD OPEN CELL
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
- CONTENTS -
4. BLOCK DIAGRAM -------------------------------------------------------9
4.1 TFT LCD OPEN CELL
5. INPUT TERMINAL PIN ASSIGNMENT ------------------------------------------------------10
5.1 TFT LCD OPEN CELL
5.2 LED CONVERTER OUTPUT PIN ASSIGNMENT
5.2 TIMING DIAGRAM OF LVDS INPUT SIGNAL
5.3 COLOR DATA INPUT ASSIGNMENT
6. CONVERTER SPECIFICATION ------------------------------------------------------13
6.1 ABSOLUTE MAXIMUM RATINGS
6.2 RECOMMENDED OPERATING RATINGS
6.3 LED CONVERTER OUTPUT RATINGS
7. INTERFACE TIMING ------------------------------------------------------16
7.1 INPUT SIGNAL TIMING SPECIFICATIONS
7.2 POWER ON/OFF SEQUENCE
8. OPTICAL CHARACTERISTICS ------------------------------------------------------19
8
.1 TEST CONDITIONS
8.2 OPTICAL SPECIFICATIONS
8.3 FLICKER ADJUSTMENT
9. PACKAGING
9.1 PACKING SPECIFICATIONS
9.2 PACKING METHOD
-----------------------------------------------------23
10. DEFINITION OF LABELS ----
10.1 CMO OPEN CELL LABEL
10.2 CMO CARTON LABEL
11. PRECAUTIONS ----
11.1 ASSEMBLY AND HANDLING PRECAUTIONS
11.2 SAFETY PRECAUTIONS
12. MECHANICAL DRAWING
-------------------------------------------------25
-------------------------------------------------26
---------------------------------------------------------27
2 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 3
Global LCD Panel Exchange Center
Version Date Section Description
Ver. 2.0 Jan, 29 ’10 - N184H6-P02 Approval Specifications was first issuedΖ
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
REVISION HISTORY
3 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 4
Global LCD Panel Exchange Center
1. GENERAL DESCRIPTION
1.1 OVERVIEW
The N184H6-P02 is a 18.4-inch TFT LCD cell with driver ICs and a 40-pin-and-2ch-LVDS circuit
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
board.
backlight unit is not built in.
The product supports 1920 x 1080 FHD mode and can display up to 262,144 colors. The
1.2 FEATURES
- FHD (1920 x 1080 pixels) resolution
- 3.3V LVDS (Low Voltage Differential Signaling) interface with 1 pixel/clock
- LED converter embedded
1.3 APPLICATION
-TFT LCD Notebook
-TFT LCD Monitor
-TFT LCD TV
1.4 GENERAL SPECIFICATI0NS
Item Specification Unit Note
Active Area 408.96 (H) x 230.04 (V) (18.47” diagonal) mm (1)
Driver Element a-si TFT active matrix - Pixel Number 1920 (H) x 3 (R.G.B.) x 1080 (V) pixel Pixel Pitch 0.213 (H) x 0.213 (V) mm Pixel Arrangement RGB vertical stripe - Display Colors 262,144 color Transmissive Mode Normally White - Surface Treatment Glare, N2T (Reflection rate< 0.5%), 3H - -
1.5 MECHANICAL SPECIFICATIONS
c Min. Typ. Max. Unit Note
Horizontal (H) with PCB 417.58 417.78 417.98 mm
Horizontal (H) w/o PCB 417.58 417.78 417.98 mm
Vertical (V) with PCB 294.422 295.422 296.422 mm
Size
Vertical (V) w/o PCB 237.725 238.725 239.725 mm
Thickness (T) with PCB - 2.4 2.64 mm
Thickness (T) w/o PCB - 1.43 1.55 mm
Weight - 299 314 g
I/F connector mounting
position
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
(2) Connector mounting position
The mounting inclination of the connector makes
the screen center within ±0.5mm as the horizontal.
+/- 0.5mm
(1) (2)
4 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 5
Global LCD Panel Exchange Center
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Symbol
Storage Temperature TST -20 +60 ºC (1)
Operating Ambient Temperature TOP 0 +50 ºC (1), (2)
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta Љ 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The temperature of panel surface should be 0 ºC Min. and 60 ºC Max.
www.panelook.com
Min. Max.
Value
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
Unit Note
Relative Humidity (%RH)
100
90
80
60
Operating Range
40
20
10
Storage Range
Temperature (ºC)
8060-20 40 0 20 -40
5 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 6
Global LCD Panel Exchange Center
2.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL)
High temperature or humidity may reduce the performance of panel. Please store LCD panel
within the specified storage conditions.
Storage Condition: With packing.
Storage temperature range: 25±5 ºC.
Storage humidity range: 50±10%RH.
Shelf life: 30days
2.3 ELECTRICAL ABSOLUTE RATINGS (OPEN CELL)
Item Symbol
Power Supply Voltage VCC -0.3 +4.0 V
Logic Input Voltage VI -0.3 VCC+0.3 V
www.panelook.com
Value
Min. Max.
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
Unit Note
(1)
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation
should be restricted to the conditions described under Normal Operating Conditions.
6 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 7
Global LCD Panel Exchange Center
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD OPEN CELL Ta = 25 ± 2 ºC
Parameter Symbol
Power Supply Voltage Vcc 3.0 3.3 3.6 V Ripple Voltage VRP 50 mV Rush Current I
Initial Stage Current IIS 1.0 A (2)
Power Supply Current
LVDS Differential Input High Threshold V
LVDS Differential Input Low Threshold V
LVDS Common Mode Voltage VCM 1.125 1.375 V (4)
LVDS Differential Input Voltage |VID| 100 600 mV (4)
Terminating Resistor RT 100 Ohm -
Note (1) The ambient temperature is Ta = 25 ± 2 ºC.
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
Value
Min. Typ. Max.
1.5 A (2)
RUSH
White 360 390 420 mA (3)a
Black
lcc
TH(LVDS)
TL(LVDS)
480 570 640 mA (3)b
+100 mV
-100 mV
Unit Note
(4),
=1.2V
V
CM
(4)
=1.2V
V
CM
Note (2) I
: the maximum current when VCCS is rising
RUSH
I
: the maximum current of the first 100ms after power-on
IS
Measurement Conditions: Shown as the following figure. Test pattern: black.
(High to Low)
(Control Signal)
SW
+12V
+3.3V
R1
47K
R2
1K
47K
VR1
C1
1uF
Q1 2SK1475
C2
0.01uF
Q2
2SK1470
FUSE
C3
1uF
VCCS
(LCD Module Input)
7 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 8
Global LCD Panel Exchange Center
|
|
|
|
Note (3) The specified power supply current is under the conditions at VCCS = 3.3 V, Ta = 25 ± 2 ºC,
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
VCCS rising time is 0.5ms
DC Current and f
a. White Pattern
Note (4) The parameters of LVDS signals are defined as the following figures.
= 60 Hz, whereas a power dissipation check pattern below is displayed.
v
b. Black Pattern
Active Area
Active Area
CM
V
VID
Single Ended
0V
V
VID
Differential
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
0V
V
8 / 27
Version 2.0
www.panelook.com
Page 9
Global LCD Panel Exchange Center
SC
C
4. BLOCK DIAGRAM
4.1 TFT LCD OPEN CELL
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
LVDS Display
Data & Clock
VCCS
GND
Data
EDID
CLK
EDID
V
EDID
Converter
Input Signals
LVDS INPUT /TIMING
CONTROLLER
AN DRIVER I
TFT LCD PANEL
INPUT CONNECTOR
DC/DC CONVERTER &
REFERENCE VOLTAGE
GENERATOR
DATA DRIVER IC
EDID
EEPROM
LED CONVERTER
LED CONVERTER
OUTPUT
PAD/CONNECTOR
9 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 10
Global LCD Panel Exchange Center
5. INPUT TERMINAL PIN ASSIGNMENT
5.1 TFT LCD OPEN CELL
Pin Symbol Description Polarity Remark
1 NC Non-Connection (Reserved for supplier)
2 Vcc Power Supply +3.3 V (typical)
3 Vcc Power Supply +3.3 V (typical)
4 V
5 NC Non-Connection (Reserved for CMO)
6 CLK
7 DATA
8 RXO0- LVDS Differential Data Input (Odd) Negative
9 RXO0+ LVDS Differential Data Input (Odd) Positive
10 Vss Ground
11 RXO1- LVDS Differential Data Input (Odd) Negative
12 RXO1+ LVDS Differential Data Input (Odd) Positive
13 Vss Ground
14 RXO2- LVDS Differential Data Input (Odd) Negative
15 RXO2+ LVDS Differential Data Input (Odd) Positive
16 Vss Ground
17 RXOC- LVDS Clock Data Input (Odd) Negative
18 RXOC+ LVDS Clock Data Input (Odd) Positive
19 Vss Ground
20 RxE0- LVDS Differential Data Input (Even) Negative
21 RxE0+ LVDS Differential Data Input (Even) Positive
22 Vss Ground
23 RxE1- LVDS Differential Data Input (Even) Negative
24 RxE1+ LVDS Differential Data Input (Even) Positive
25 Vss Ground
26 RxE2- LVDS Differential Data Input (Even) Negative
27 RxE2+ LVDS Differential Data Input (Even) Positive
28 Vss Ground
29 RXEC- LVDS Clock Data Input (Even) Negative
30 RXEC+ LVDS Clock Data Input (Even) Positive
31 LED_GND LED Ground
32 LED_GND LED Ground
33 LED_GND LED Ground
34 NC Non-Connection
35 LED_PWM PWM Control Signal of LED Converter
36 LED_EN Enable Control Signal of LED Converter
37 NC Non-Connection
38 LED_VCCS LED Power
39 LED_VCCS LED Power
40 LED_VCCS LED Power
Note (1) Connector Part No.: I-PEX 20455-040E-12 or equivalent
DDC 3.3V Power
EDID
DDC Clock
EDID
DDC Data
EDID
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
Note (2) User’s connector Part No: I-PEX 20453-040T-01 or equivalent
Note (3) The first pixel is odd as shown in the following figure.
10 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 11
Global LCD Panel Exchange Center
5.2 LED CONVERTER OUTPUT PIN ASSIGNMENT
Pin Symbol Description
1 V
L
2 VL LED converter output voltage
3 VL LED converter output voltage
4 NC No connection
5 CH1 LED converter feedback channel 1
6 CH2 LED converter feedback channel 2
7 CH3 LED converter feedback channel 3
8 CH4 LED converter feedback channel 4
9 CH5 LED converter feedback channel 5
10 CH6 LED converter feedback channel 6
11 CH7 LED converter feedback channel 7
12 CH8 LED converter feedback channel 8
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
LED converter output voltage
Note (1) Connector Part No.: FCI-59453-12110EDHLF or equivalent
5.3 TIMING DIAGRAM OF LVDS INPUT SIGNAL
CLK+
T/7
Rxin2
Rxin1
Rxin0
IN20 IN19 IN18 IN17 IN16 IN15 IN14
DE B5 B4 B3 B2 Vsync Hsync
IN13 IN12 IN11 IN10 IN9 IN8 IN7
B1 G4 G3 G2 G1 B0 G5
IN6 IN5 IN4 IN3 IN2 IN1 IN0
G0 R3 R2 R1 R0
R5
R4
Signal for 1 DCLK Cycle (T)
11 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 12
Global LCD Panel Exchange Center
5.4 COLOR DATA INPUT ASSIGNMENT
The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input
for the color. The higher the binary input, the brighter the color. The table below provides the
assignment of color versus data input.
Color
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Black
Red
Green
Basic
Colors
Gray
Scale
Of
Red
Gray
Scale
Of
Green
Gray
Scale
Of
Blue
Note (1) 0: Low Level Voltage, 1: High Level Voltage
Blue
Cyan
Magenta
Yellow
White
Red(0)/Dark
Red(1)
Red(2)
:
:
Red(61)
Red(62)
Red(63)
Green(0)/Dark
Green(1)
Green(2)
:
:
Green(61)
Green(62)
Green(63)
Blue(0)/Dark
Blue(1)
Blue(2)
:
:
Blue(61)
Blue(62)
Blue(63)
0
1
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
Data Signal
Red Green Blue
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
12 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 13
Global LCD Panel Exchange Center
6. CONVERTER SPECIFICATION
6.1 ABSOLUTE MAXIMUM RATINGS
Symbol Ratings
LED_VCCS -0.3~28V
LED_PWM -0.3V~5.5V
LED_EN -0.3V~5.5V
6.2 RECOMMENDED OPERATING RATINGS
Parameter Symbol
Converter Input power supply voltage
Converter Rush Current
Converter Initial Stage Current
EN Control Level
PWM Control Level
PWM Control Duty Ratio
PWM Control Permissive Ripple Voltage
PWM Control Frequency f
Note (1) ILED
ILED
: the maximum current when LED_VCCS is rising,
RUSH
: the maximum current of the first 100ms after power-on,
IS
Measurement Conditions: Shown as the following figure. LED_VCCS = Typ, Ta = 25 ± 2 ºC,
Backlight On 2 --- 5 V Backlight Off 0 --- 0.5 V PWM High Level 2 --- 5 V PWM Low Level 0 --- 0.15 V -
www.panelook.com
Min. Typ. Max.
LED_Vccs
ILED
RUSH
ILED
IS
VPWM_pp
190 210 1K Hz (3)
PWM
6 12 21 V -
- - 1.5 A (1)
- - 1.5 A (1)
10 - 100 % -
5 - 100 % (2)
- - 100 mV -
Value
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
Unit Note
f
= 200 Hz, Duty=100%.
PWM
LED_VCCS(Typ)
(High to Low)
(Control Signal)
SW=24V
LED_VCCS(Typ)
VR1
C1
1uF
R1
47K
47K
Q1 IRL3303
FUSE
R2
1K
0.01uF
Q2
IRL3303
C2
C3
1uF
(LED Converter Input)
13 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 14
Global LCD Panel Exchange Center
≤∗+
+
≤
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
VLED rising time is 0.5ms
0.5ms
90%
ILED
10%
Rush
100ms
ILED
IS
LED_VCC
LED_PWM
LED_EN
ILED
Note (2) If the PWM control duty ratio is less than 10%, there is some possibility that acoustic noise or
backlight flash can be found. And it is also difficult to control the brightness linearity.
Note (3) If PWM control frequency is applied in the range less than 1KHz, the “waterfall” phenomenon
on the screen may be found. To avoid the issue, it’s a suggestion that PWM control frequency
0V
0V
0V
should follow the criterion as below.
PWM control frequency f
N
should be in the range
PWM
fN )33.0( f
PWM
: Integer )3( ≥N
f
14 / 27
)66.0(
: Frame rate
fN ∗
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 15
Global LCD Panel Exchange Center
6.3 LED CONVERTER OUTPUT RATINGS
Parameter Symbol
Converter output voltage
Converter output current
Converter feedback channel current ICH 19 20 21 mA
www.panelook.com
Min. Typ. Max.
V
L
I
L
25.2 28.8 31.5 V
152 160 168 mA
Value
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
Unit Note
15 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 16
Global LCD Panel Exchange Center
7. INTERFACE TIMING
7.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
DCLK Frequency 1/Tc 62 69.25 72.7 MHz -
Vertical Total Time TV 1082 1111 1350 TH -
Vertical Active Display Period TVD 1080 1080 1080 TH -
DE
Note (1) Because this module is operated by DE only mode, Hsync and Vsync are ignored.
Vertical Active Blanking Period TVB TV-TVD 31 TV-TVD TH -
Horizontal Total Time TH 2002 2080 2400 Tc -
Horizontal Active Display Period THD 1920 1920 1920 Tc -
Horizontal Active Blanking Period THB
www.panelook.com
TH-THD
INPUT SIGNAL TIMING DIAGRAM
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
160
TH-THD
Tc -
DE
DCLK
DE
DATA
TC
HD
T
16 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 17
Global LCD Panel Exchange Center
7.2 POWER ON/OFF SEQUENCE
90%
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
t7
90%
- Power Supply
for LCD, VCCS
- Interface Signal
(LVDS Signal of
Transmitter), V
I
- Power Supply for
LED Converter,
LED_VCCS
- LED Converter
Dimming Signal,
LED_PWM
- LED Converter
Enable Signal,
LED_EN
0V
0V
0V
0V
0V
10%
10%
t1
t2
t3
10%
t4
Valid Data
t6t5
90%
10%
t
B
t
D
F
10%
90%
t
A
t
C
tE t
Timing Specifications:
0.5Љ t1ʳЉ 10 ms
0 Љ t2ʳЉ 50 ms
0 Љ t3ʳЉ 50 ms
t4ʳЊ 500 ms
t5ʳЊ 200 ms
t6ʳЊ 200 ms
0.5Љ t7ʳЉʳ 10 ms
0.5Љ t
0 І t
ʳЉʳ 10 ms
A
ʳЉʳ 10 ms
B
t
ʳЊ 10 ms
C
t
ʳЊ 10 ms
D
t
ʳЊ 10 ms
E
t
ʳЊ 10 ms
F
17 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 18
Global LCD Panel Exchange Center
Note (1) Please follow the power on/off sequence described above. Otherwise, the LCD module might be
damaged.
Note (2) Please avoid floating state of interface signal at invalid period. When the interface signal is invalid,
be sure to pull down the power supply of LCD VCCS to 0 V.
Note (3)The backlight must be turned on after the power supply for the logic and the interface signal is valid.
The backlight must be turned off before the power supply for the logic and the interface signal is
invalid.
Note (4) Please follow the LED converter power sequence as above. If the customer could not follow, it
might cause backlight flash issue during display ON/OFF or damage the LED backlight controller
www.panelook.com
Issued Date: Jan. 29, 2010
Model No.: N184H6-P02
Approval
18 / 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.0
www.panelook.com
Page 19
Global LCD Panel Exchange Center
8. OPTICAL CHARACTERISTICS
8.1 TEST CONDITIONS
Item Symbol Value Unit
Ambient Temperature Ta
Ambient Humidity Ha
Supply Voltage VCC 3.3 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
8.2 OPTICAL SPECIFICATIONS
The relative measurement methods of optical characteristics are shown as below. The following items
should be measured under the test conditions described in 7.1 and stable environment shown in Note (6).
Item Symbol Condition Min. Typ. Max. Unit Note
Red
Color
Chromaticity
Center Transmittance T%
Contrast Ratio CR
Response Time
Transmittance uniformity δT%
Viewing Angle
Green
Blue
White
Horizontal
Vertica l
www.panelook.com
25±2
50±10
Rcx
Rcy
Gcx
θ
=0° , θY =0°
Gcy
Bcx
Bcy
Standard light source “C”
x
CS-2000T
Typ -
0.03
Wcx
Wcy
θ
=0° , θY =0°
x
4.59 5.40
CS-2000T, CMO BLU 300 500 - (1), (3)
T
R
T
F
θ
=0° , θY =0°
x
θ
=0° , θY =0°
x
BM-5A
θx+ 40 45
- 40 45
θ
x
θY+ 15 20
-
θ
Y
CR≥10
BM-5A
0.639 -
0.330 -
0.277 -
0.575 -
0.153 -
0.113 -
0.313
0.343
6 12
1.25 1.40 - (1), (7)
40 45
Doc. No.:
Issued Date: Sep. 7, 2009
Model No.: N154C6-P04
Approval
o
C
%RH
Typ +
0.03
-
-
(1), (8)
28
ms
ms
Deg.
(0),(6)
(4)
(1), (3)
(6)
Note (0) Light source is the standard light source “C” which is defined by CIE and driving voltages are
based on suitable gamma voltages. The calculating method is as followingΚ
1. Measure Module’s and BLU’s spectrums. White is without signal input and R, G, B are with
signal input. BLU is supplied by CMO.
2. Calculate cell’s spectrum.
3. Calculate cell’s chromaticity by using the spectrum of standard light source “C”
Note (1) Light source is the BLU which is supplied by CMO and driving voltages are based on suitable
gamma voltages. White is without signal input and R, G, B are with signal input. SPEC is judged
by CMO’s golden sample.
19 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 20
Global LCD Panel Exchange Center
s
Note (2) Definition of Viewing Angle (θ x, θy):
www.panelook.com
Doc. No.:
Issued Date: Sep. 7, 2009
Model No.: N154C6-P04
Approval
Normal
θx = θy = 0º
θy- θy+
θX- = 90º
6 o’clock
θ
y- = 90º
x-
y-
Note (3) Definition of Contrast Ratio (CR):
CR
= [CR(1)+ CR(2)+ CR(3)+ CR(4)+ CR(5)] / 5
AVE
CR
=Max value of CR at whole Viewing Angle
max
CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).
Luminance with all pixel white (Gmax)
CR =
Luminance with all pixel black (Gmin)
θx−
θx+
y+
12 o’clock direction
θ
y+ = 90º
x+
θX+ = 90º
Gmax: Luminance of gray max at the center point of panel.
Gmin: Luminance of gray min at the center point of panel.
Note (4) Definition of Response Time (T
Gray Level 255
100%
90%
Optical
Response
10%
0%
T
66.67 m
R
R
, TF):
T
F
66.67 ms
Gray Level 255
Time
20 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 21
Global LCD Panel Exchange Center
Note (5) Definition of Luminance of White (LC):
Measure the luminance of gray level 255 at center point
L
= L (5)
C
L (x) is corresponding to the luminance of the point X at Figure in Note (7).
Note (6) Measurement Setup:
The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt
temperature change during measuring. In order to stabilize the luminance, the measurement
should be executed after lighting Backlight for 20 minutes in a windless room.
LCD Module
LCD Panel
www.panelook.com
Doc. No.:
Issued Date: Sep. 7, 2009
Model No.: N154C6-P04
Approval
USB2000
Field of View = 2º
Center of the Screen
Note (7) Definition of Transmittance Variation (δT%):
Measure the transmittance at 5 points
Maximum [T%(1), T%(2), … T%(5)]
T% =
δ
Minimum [T%(1), T%(2), … T%(5)]
Horizontal Line
D/4 D/2 3D/4
CS-2000T
Light Shield Room
(Ambient Luminance < 2 lux)
D
W/4
W/2
W
Vertical Line
3W/4
1 2
X
: Test Point
X=1 to 5
3
5
4
Active Area
21 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 22
Global LCD Panel Exchange Center
Note (8) Definition of Transmittance (T%):
Module is without signal input.
BLU is supplied by CMO.
Transmittance =
8.3 Flicker Adjustment
(1) Adjustment Pattern: 2H1V checker pattern as follows.
www.panelook.com
Doc. No.:
Issued Date: Sep. 7, 2009
Model No.: N154C6-P04
Approval
Luminance of LCD module
Ϡ 100%
Luminance of backlight
(2) Adjustment Method:
Flicker should be adjusted by turning the volume for flicker adjustment by the ceramic driver. It is
adjusted to the point with least flickering of the whole screen. After making it surely overrun at once, it
should be adjusted to the optimum point.
22 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 23
Global LCD Panel Exchange Center
9. PACKAGING
9.1 PACKING SPECIFICATIONS
(1) 27 open cells / 1 Box
(2) Box dimensions: 570mm(L) X 450mm(W) X 320mm(H)
(3) Weight: approximately 18.3Kg (27 open cells per box)
9.2 PACKING METHOD
(1) Carton Packing should have no failure in the following reliability test items
Test Item Test Conditions Note
ISTA STANDARD
Packing
Vibration
Random, Frequency Range: 1 – 200 Hz
Top & Bottom: 30 minutes (+Z), 10 min (-Z),
Right & Left: 10 minutes (X)
Back & Forth 10 minutes (Y)
www.panelook.com
Doc. No.:
Issued Date: Sep. 7, 2009
Model No.: N154C6-P04
Approval
Non Operation
(2) Packing method.
23 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 24
Global LCD Panel Exchange Center
www.panelook.com
Doc. No.:
Issued Date: Sep. 7, 2009
Model No.: N154C6-P04
Approval
24 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 25
Global LCD Panel Exchange Center
10. DEFINITION OF LABELS
10.1 CMO OPEN CELL LABEL
The barcode nameplate is pasted on each OPEN CELL as illustration for CMO internal control.
N184H6-P02 RoHS Rev.XX
CM18H62XXXXXLXXLYMDNNNNʳ
Barcode definition:
www.panelook.com
Doc. No.:
Issued Date: Sep. 7, 2009
Model No.: N154C6-P04
Approval
Serial ID: CM
Code Meaning Description
CM Supplier code CMO=CM
18H62 Model number N184H6-P02=18H62
X Revision code C1:1 ,C2:2……
X Source driver IC code
X Gate driver IC code
XX Cell location Tainan, Taiwan=TN
L Cell line # 0~12=1~C
XX Module location Tainan, Taiwan=TN
L Module line # 0~12=1~C
YMD
NNNN Serial number Manufacturing sequence of product
-18H62-X-X-X-XX-L-XX-L-YMD-NNNN
Century=1, CLL=2, Demos=3, Epson=4, Fujitsu=5, Himax=6,
Hitachi=7, Hynix=8, LDI=9, Matsushita=A, NEC=B, Novatec=C,
OKI=D, Philips=E, Renasas=F, Samsung=G, Sanyo=H, Sharp=I,
TI=J, Topro=K, Toshiba=L, Windbond=M
Year, month, day Year: 2001=1, 2002=2, 2003=3, 2004=4…
Month: 1~12=1, 2, 3, ~, 9, A, B, C
Day: 1~31= 1, 2, 3, ~, 9, A, B, C, ~, T, U, V
10.2 CARTON LABEL
The barcode nameplate is pasted on each box as illustration, and its definitions are as following explanation
(a) Model Name: N184H6 –P02
(b) Carton ID: CMO internal control
(c) Quantities: 27
ˡ˄ˋˇ˛ˉˀˣ˃˅ʳ
˫˫ʳ
25 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 26
Global LCD Panel Exchange Center
www.panelook.com
Doc. No.:
Issued Date: Sep. 7, 2009
Model No.: N154C6-P04
Approval
11. PRECAUTIONS
11.1 ASSEMBLY AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the product during assembly.
(2) To assemble backlight or install module into user’s system can be only in clean working areas. The
dust and oil may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel will be
damaged.
(4) Always follow the correct power sequence when the product is connecting and operating. This can
prevent damage to the CMOS LSI chips during latch-up.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
(7) It is dangerous that moisture come into or contacted the product, because moisture may damage the
product when it is operating.
(8) High temperature or humidity may reduce the performance of module. Please store this product within
the specified storage conditions.
(9) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the
response time will become slowly.
11.2 SAFETY PRECAUTIONS
(1) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
(2) After the product’s end of life, it is not harmful in case of normal operation and storage.
26 / 27
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 27
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...