CMO M236H1-P01 Specification

Global LCD Panel Exchange Center

TFT LCD Approval Specification

MODEL NO.: M236H1-P01

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

Customer :

Approved by :

Note :

Liquid Crystal Display Division

QRA Division. OA Head Division.

Approval Approval

1 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

- CONTENTS -

REVISION HISTORY

1. GENERAL DESCRIPTION

1.1 OVERVIEW

1.2 FEATURES

1.3 APPLICATION

1.4 GENERAL SPECIFICATIONS

1.5 MECHANICAL SPECIFICATIONS

2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT (BASED ON CMO MODULE M236H1-L01)

2.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL)

2.3 ELECTRICAL ABSOLUTE RATINGS (OPEN CELL)

3. ELECTRICAL CHARACTERISTICS

3.1 TFT LCD OPEN CELL

3.2 Vcc POWER DIP CONDITION

4. BLOCK DIAGRAM

4.1 TFT LCD OPEN CELL

5. INPUT TERMINAL PIN ASSIGNMENT

5.1 TFT LCD MODULE

5.2 LVDS DATA MAPPING TABLE

5.3 COLOR DATA INPUT ASSIGNMENT

6. INTERFACE TIMING

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

6.2 POWER ON/OFF SEQUENCE

7. OPTICAL CHARACTERISTICS

7.1 TEST CONDITIONS

7.2 OPTICAL SPECIFICATIONS

7.3 FLICKER ADJUSTMENT

8. PACKAGING

8.1 PACKING SPECIFICATIONS

8.2 PACKING METHOD

9. DEFINITION OF LABELS

9.1 OPEN CELL LABEL

9.2 CARTON LABEL

10. PRECAUTIONS

10.1 ASSEMBLY AND HANDLING PRECAUTIONS

10.2 SAFETY PRECAUTIONS

11. MECHANICAL DRAWING

-------------------------------------------------------

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

3

4

5

7

9

10

13

15

20

22

23

24

2 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

REVISION HISTORY

Version Date Section Description

Ver. 2.0 Nov, 13 ’08

- M236H1-P01 Approval Specifications was first issued.

3 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

1. GENERAL DESCRIPTION

1.1 OVERVIEW

The M236H1-P01 is a 23.6-inch wide TFT LCD cell with driver ICs and a 30-pins-2ch-LVDS circuit

board. The product supports 1920 x 1080 HDTV (16:9 wide screen) mode and can display up to 16.7M

colors. The backlight unit is not built in.

1.2 FEATURES

- Super wide viewing angle

- High contrast ratio

- Fast response time

- High color saturation

- HDTV (1920 x 1080 pixels) resolution

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

- DE (Data Enable) only mode

- LVDS (Low Voltage Differential Signaling) interface

- RoHS Compliance

1.3 APPLICATION

- TFT LCD Monitor

- TFT LCD TV

- Workstation & desktop monitor

- Display terminals for AV application

1.4 GENERAL SPECIFICATI0NS

Item Specification Unit Note Diagonal Size 23.547 inch Active Area 521.28 (H) x 293.22 (V) mm (1) Driver Element a-Si TFT active matrix - Pixel Number 1920 x R.G.B. x 1080 pixel Pixel Pitch 0.2715 (H) x 0.2715 (V) mm Pixel Arrangement RGB vertical stripe - Display Colors 16.7M color Transmissive Mode Normally White - Surface Treatment Hard coating (3H), Anti-glare (Haze 25%) - -

1.5 MECHANICAL SPECIFICATIONS

Item Min. Typ. Max. Unit Note Weight I/F connector mounting position

Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.

(2) Connector mounting position

The mounting inclination of the connector makes the screen center within ±0.5mm as the horizontal.

- -

695 g -

(2)

+/- 0.5mm

4 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT (BASED ON CMO MODULE M220J1-L01)

Item Symbol

Storage Temperature TST -20 +60 ºC (1) Operating Ambient Temperature TOP 0 +50 ºC (1), (2)

Note (1) Temperature and relative humidity range is shown in the figure below.

Min. Max.

Value

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

Unit Note

(a) 90 %RH Max. (Ta

(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).

(c) No condensation.

Note (2) The temperature of panel display surface area should be 0 ºC Min. and 60 ºC Max.

Relative Humidity (%RH)

Љ 40 ºC).

100

90

80

60

Operating Range

40

20

10

Storage Range

Temperature (

5 / 24

к

80 60 -20 40 0 20 -40

)

Version 2.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

2.2 ABSOLUTE RATINGS OF ENVIRONMENT (OPEN CELL)

High temperature or humidity may reduce the performance of panel. Please store LCD panel within

the specified storage conditions.

Storage Condition: With packing.

Storage temperature range: 25±5 ºC.

Storage humidity range: 50±10%RH.

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

Shelf life: 30days

2.3 ELECTRICAL ABSOLUTE RATINGS (OPEN CELL)

Item Symbol

Power Supply Voltage VCC -0.3 +6.0 V (1)

Note (1) Permanent damage might occur if the module is operated at conditions exceeding the maximum

values.

Value

Min Max

Unit Note

6 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

3. ELECTRICAL CHARACTERISTICS

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

3.1 TFT LCD OPEN CELL

Parameter Symbol

Ta = 25 ± 2 ºC

Value

Min. Typ. Max.

Unit Note

Power Supply Voltage Vcc 4.5 5.0 5.5 V Ripple Voltage VRP - -- 100 mV Rush Current I

- -- 3 A (2)

RUSH

White - 0.6 0.72 A (3)a

Power Supply Current

Black - 0.9 1.08 A (3)b Vertical Stripe

Power Consumption P

lcc

- 0.85 1.02 A (3)c

LCD

4.5 5.4 Watt (4) LVDS differential input voltage Vid 100 - 600 mV LVDS common input voltage Vic -- 1.2 -- V

Note (1) The module is recommended to operate within specification ranges listed above for normal

function.

Note (2) Measurement Conditions:

+5.0V

R1

47K

Q1 2SK1475

FUSE

C3

Vcc

(LCD Module Input)

1uF

(High to Low)

(Control Signal)

SW

+12V

R2

1K

Q2

2SK1470

47K

C1

1uF

VR1

C2

0.01uF

Vcc rising time is 470μs

Vcc

0.9Vcc

0.1Vcc

GND

470μs

7 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

Note (3) The specified power supply current is under the conditions at Vcc = 5.0 V, Ta = 25 ± 2 ºC, f

Hz, whereas a power dissipation check pattern below is displayed.

a. White Pattern

Active Area

c. Vertical Stripe Pattern

b. Black Pattern

Active Area

R

G

B

R

B

G

B

R

G

B

R

= 60

v

Note (4) The power consumption is specified at the pattern with the maximum current.

Active Area

R

B

G

R R

G

B

R

G

3.2 Vcc Power Dip Condition:

Vcc

4.5V

Dip condition:

Td

msTdVVccV 20,5.40.4 ≤≤≤

4.0V

B

R

8 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

q

)

4. BLOCK DIAGRAM

4.1 TFT LCD OPEN CELL

RXO0(+/-)

RXO1(+/-)

RXO2(+/-)

RXO3(+/-)

RXOC(+/-)

RXE0(+/-)

RXE1(+/-)

RXE2(+/-)

RXE3(+/-)

RXEC(+/-)

AGMODE

NC

Vcc

GND

(STM MSAK

INPUT CONNECTOR

(FI-X30SSL-HF)

or E

uivalent

T2407P30HA

www.panelook.com

LVDS INPUT /

TIMING CONTROLLER

DC/DC CONVERTER &

REFERENCE VOLTAGE

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

SCAN DRIVER IC

TFT LCD PANEL

(1920x3x1200)

(1920x3x1080)

DATA DRIVER IC

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

9 / 24

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

5. INPUT TERMINAL PIN ASSIGNMENT

5.1 TFT LCD MODULE

Pin Name Description

1 RXO0- Negative LVDS differential data input. Channel O0 (odd) 2 RXO0+ Positive LVDS differential data input. Channel O0 (odd) 3 RXO1- Negative LVDS differential data input. Channel O1 (odd) 4 RXO1+ Positive LVDS differential data input. Channel O1 (odd) 5 RXO2- Negative LVDS differential data input. Channel O2 (odd) 6 RXO2+ Positive LVDS differential data input. Channel O2 (odd) 7 GND Ground 8 RXOC- Negative LVDS differential clock input. (odd)

9 RXOC+ Positive LVDS differential clock input. (odd) 10 RXO3- Negative LVDS differential data input. Channel O3(odd) 11 RXO3+ Positive LVDS differential data input. Channel O3 (odd) 12 RXE0- Negative LVDS differential data input. Channel E0 (even) 13 RXE0+ Positive LVDS differential data input. Channel E0 (even) 14 GND Ground 15 RXE1- Negative LVDS differential data input. Channel E1 (even) 16 RXE1+ Positive LVDS differential data input. Channel E1 (even) 17 GND Ground 18 RXE2- Negative LVDS differential data input. Channel E2 (even) 19 RXE2+ Positive LVDS differential data input. Channel E2 (even) 20 RXEC- Negative LVDS differential clock input. (even) 21 RXEC+ Positive LVDS differential clock input. (even) 22 RXE3- Negative LVDS differential data input. Channel E3 (even) 23 RXE3+ Positive LVDS differential data input. Channel E3 (even) 24 GND Ground 25 NC Not connection, this pin should be open. 26 NC Not connection, this pin should be open. 27 NC Not connection, this pin should be open. 28 Vcc +5.0V power supply 29 Vcc +5.0V power supply 30 Vcc +5.0V power supply

Note (1) Connector Part No.: STM MSAKT2407P30HA or EQUIVALENT.

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

Note (2) The first pixel is odd.

Note (3) Input signal of even and odd clock should be the same timing.

10 / 24

Version 2.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

5.2 LVDS DATA MAPPING TABLE

LVDS Channel O0

LVDS Channel O1

LVDS Channel O2

LVDS Channel O3

LVDS Channel E0

LVDS Channel E1

LVDS Channel E2

LVDS Channel E3

LVDS output D7 D6 D4 D3 D2 D1 D0 Data order OG0 OR5 OR4 OR3 OR2 OR1 OR0 LVDS output D18 D15 D14 D13 D12 D9 D8 Data order OB1 OB0 OG5 OG4 OG3 OG2 OG1 LVDS output D26 D25 D24 D22 D21 D20 D19 Data order DE NA NA OB5 OB4 OB3 OB2 LVDS output D23 D17 D16 D11 D10 D5 D27 Data order NA OB7 OB6 OG7 OG6 OR7 OR6 LVDS output D7 D6 D4 D3 D2 D1 D0 Data order EG0 ER5 ER4 ER3 ER2 ER1 ER0 LVDS output D18 D15 D14 D13 D12 D9 D8 Data order EB1 EB0 EG5 EG4 EG3 EG2 EG1 LVDS output D26 D25 D24 D22 D21 D20 D19 Data order DE NA NA EB5 EB4 EB3 EB2 LVDS output D23 D17 D16 D11 D10 D5 D27 Data order NA EB7 EB6 EG7 EG6 ER7 ER6

11 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

5.3 COLOR DATA INPUT ASSIGNMENT

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for

the color. The higher the binary input, the brighter the color. The table below provides the assignment of

color versus data input.

Color

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

Basic Colors

Gray Scale Of Red

Black Red Green Blue Cyan Magenta Yellow White Red(0) / Dark Red(1) Red(2)

:

: Red(253) Red(254) Red(255)

0

1

0

1

0

:

1

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

Data Signal

Red Green Blue

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

:

1

0

1

0

1

0

1

0

Green(0) / Dark

Gray Scale Of Green

Gray Scale Of Blue

Note (1) 0: Low Level Voltage, 1: High Level Voltage

Green(1) Green(2)

:

: Green(253) Green(254) Green(255) Blue(0) / Dark Blue(1) Blue(2)

:

: Blue(253) Blue(254) Blue(255)

0

:

0

:

0

1

0

1

0

:

0

1

0

1

0

1

0

1

0

:

0

1

0

1

0

1

0

0 0

0

:

1

0

:

0

:

1

0

:

0

1

0

1

0

:

1

0

1 0

1

12 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

6. INTERFACE TIMING

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

The input signal timing specifications are shown as the following table and timing diagram.

Signal Item Symbol Min. Typ. Max. Unit Note

Frequency Fc 58.54 74.25 98 MHz -

LVDS Clock

LVDS Data

Vertical Active Display Term

Horizontal Active Display Term

NoteΚ(1) Because this module is operated by DE only mode, Hsync and Vsync input signals should be

Period Tc 17.08 13.47 10.20 ns High Time Tch - 4/7 - Tc Low Time Tcl - 3/7 - Tc Setup Time Tlvs 600 - - ps Hold Time Tlvh 600 - - ps Frame Rate Fr 50 60 75 Hz Tv=Tvd+Tvb Total Tv 1115 1125 1136 Th Display Tvd 1080 1080 1080 Th Blank Tvb 35 45 56 Th Total Th 1050 1100 1150 Tc Th=Thd+Thb Display Thd 960 960 960 Tc Blank Thb 90 140 190 Tc -

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

set to low logic level or ground. Otherwise, this module would operate abnormally.

INPUT SIGNAL TIMING DIAGRAM

DE

Th

DCLK

C

DE

DATA

T

Thb

T

hd

13 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

pply

g

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

6.2 POWER ON/OFF SEQUENCE

To prevent a latch-up or DC operation of LCD module, the power on/off sequence should follow the

conditions shown in the following diagram.

Restart

Power On

Power Off

- Power Su for LCD, Vcc

- Interface Si (LVDS Signal of Transmitter), V

- Recommended

power for Lamp

Timing Specifications:

0.5< t1

0 < t2

0 < t3

0V

nal

0V

I

Љ 10 msec

Љ 50 msec

t4

Њ 500 msec

t5

Њ 450 msec

10%

90%

t1

90%

10%

t7

t3 t2

Valid Data

t6 t5

50% 50%

ON OFF OFF

t4

10%

t6

Њ 90 msec

5< t7

Љ 100 msec

Note.

(1) The supply voltage of the external system for the module input should be the same as the definition of Vcc.

(2) Please apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD

operation of the LCD turns off, the display may, instantly, function abnormally.

(3) In case of

(4) T4 should be measured after the module has been fully discharged between power on/off periods.

(5) Interface signal shall not be kept at high impedance when the power is on.

(6) The company will not guarantee or compensate for the product damage caused by not following the Power

Sequence.

VCC

= off level, please keep the level of input signals on the low or keep a high impedance.

14 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

7. OPTICAL CHARACTERISTICS

7.1 TEST CONDITIONS

Item Symbol Value Unit Ambient Temperature Ta Ambient Humidity Ha Supply Voltage VCC 7.0 V Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS" Inverter Current IL Inverter Driving Frequency FL

7.2 OPTICAL SPECIFICATIONS

The relative measurement methods of optical characteristics are shown as below. The following items

should be measured under the test conditions described in 7.1 and stable environment shown in Note (6).

Item Symbol Condition Min. Typ. Max. Unit Note

Red

Color

Chromaticity

(CIE 1931)

Center Transmittance T% Contrast Ratio CR

Response Time

Transmittance uniformity

Viewing Angle

Green

Blue

White

Horizontal

Vertical

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

o

25 ± 2

50 ± 10

7.0 ± 0.5 55 ± 5

Rcx 0.647

Rcy

0.334

Gcx 0.284

θ

=0°, θY =0°

Gcy

Bcx 0.151

Standard light source “C”

x

CS-1000T

Typ -

0.03

Bcy

0.607

0.071

Typ +

0.03

Wcx 0.313 Wcy

θ

=0°, θY =0°

x

CS-1000T, CMO BLU TR --- 1.5 2.5 ms T

F

δT%

θ

=0°, θY =0°

x

=0°, θY =0°

θ

x

USB2000

4.7 5.25 ---

700 1000 --- - (1), (3)

θx+

θ

-

x

θY+

θ

Y

-

CR≥10

USB2000

0.329

--- 3.5 5.5 ms

--- --- 1.33

75 75

70 70

85 --85 80 80

---

C

%RH

mA

KHz

-

%

-

Deg.

(0),(6)

(1), (8)

(4)

(1), (7)

(1), (2)

(6)

15 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

7.3 Flicker Adjustment

(1) Adjustment Pattern: 2H1V checker pattern as follows.

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

(2)

Adjustment Method:

Flicker should be adjusted by turning the volume for flicker adjustment by the ceramic driver. It is adjusted

to the point with least flickering of the whole screen. After making it surely overrun at once, it should be

adjusted to the optimum point.

16 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

Note (0) Light source is the standard light source “C” which is defined by CIE and driving voltages are based

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

on suitable gamma voltages. The calculating method is as following

1. Measure Module’s and BLU’s spectrums. White is without signal input and R, G, B are with signal

input. BLU (for M236H1-P01) is supplied by CMO.

2. Calculate cell’s spectrum.

3. Calculate cell’s chromaticity by using the spectrum of standard light source “C”

Note (1) Light source is the BLU which is supplied by CMO and driving voltages are based on suitable gamma

voltages.

Note (2) Definition of Viewing Angle (θx, θy):

Normal

θx = θy = 0º

θy- θy+

Ǻ

Note (3) Definition of Contrast Ratio (CR):

θX- = 90º

6 o’clock

θ

y-

= 90º

The contrast ratio can be calculated by the following expression.

Contrast Ratio (CR) = L255 / L0

L255: Luminance of gray level 255

L 0: Luminance of gray level 0

CR = CR (5)

x-

y-

θx−

θx+

12 o’clock direction

y+

θ

y+

= 90º

x+

θX+ = 90º

CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (7).

17 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

T

Note (4) Definition of Response Time (TR, TF):

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

100%

90%

Optical

Response

Gray Level 255

10%

0%

Note (5) Definition of Luminance of White (L

Measure the luminance of gray level 255 at center point

L

= L (5)

C

L (x) is corresponding to the luminance of the point X at Figure in Note (7).

Gray Level 255

ime

T

R

):

C

F

Note (6) Measurement Setup:

The LCD module should be stabilized at given temperature for 40 minutes to avoid abrupt

temperature change during measuring. In order to stabilize the luminance, the measurement

should be executed after lighting Backlight for 40 minutes in a windless room.

LCD

LCD Panel

USB2000

Field of View = 2º

Center of the Screen

CS-1000T

Light Shield Room

(Ambient Luminance < 2 lux)

18 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

Note (7) Definition of Transmittance Variation (δT%):

Measure the transmittance at 9 points

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

δT% =

W/10

W/2

W

Vertical Line

W/10

Maximum [L (1), L (2),……….L (8), L (9)]

Minimum [L (1), L (2),…… ….L (8), L (9)]

Horizontal Line

D

D/10 D/2

1 3

4

7

Active Area

2

5

8

D/10

6

9

: Test Point

X

X=1 to 9

Note (8) Definition of Transmittance (T%):

Module is without signal input.

Transmittance =

Luminance of LCD module

Ϡ 100%

Luminance of backlight

19 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

8. PACKAGING

8.1 PACKING SPECIFICATIONS

(1) 27 open cells / 1 Box

(2) Box dimensions: 650 (L) X 550 (W) X 320 (H) mm

(3) Weight: approximately 15.1Kg (13 open cells per box)

8.2 PACKING METHOD

(1) Carton Packing should have no failure in the following reliability test items

Test Item Test Conditions Note

ISTA STANDARD

Packing Vibration

Random, Frequency Range: 1 – 200 Hz Top & Bottom: 30 minutes (+Z), 10 min (-Z), Right & Left: 10 minutes (X) Back & Forth 10 minutes (Y)

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

Non Operation

(2) Packing method.

20 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

21 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

9. DEFINITION OF LABELS

9.1 CMO OPEN CELL LABEL

The barcode nameplate is pasted on each OPEN CELL as illustration for CMO internal control.

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

Serial ID: CM

Code Meaning Description

CM Supplier code CMO=CM

22J11 Model number M236H1-P01=23H11

X Revision code C1:1 ,C2:2……

X Source driver IC code

X Gate driver IC code

XX Cell location Tainan, Taiwan=TN

L Cell line # 0~12=1~C

XX Module location Tainan, Taiwan=TN

L Module line # 0~12=1~C

YMD

NNNN Serial number Manufacturing sequence of product

-23H11-X-X-X-XX-L-XX-L-YMD-NNNN

Year, month, day Year: 2001=1, 2002=2, 2003=3, 2004=4…

9.2 CARTON LABEL

Barcode definition:

Century=1, CLL=2, Demos=3, Epson=4, Fujitsu=5, Himax=6, Hitachi=7, Hynix=8, LDI=9, Matsushita=A, NEC=B, Novatec=C, OKI=D, Philips=E, Renasas=F, Samsung=G, Sanyo=H, Sharp=I, TI=J, Topro=K, Toshiba=L, Windbond=M

Month: 1~12=1, 2, 3, ~, 9, A, B, C Day: 1~31= 1, 2, 3, ~, 9, A, B, C, ~, T, U, V

The barcode nameplate is pasted on each box as

22 / 24

illustration, and its definitions are as following

explanation

(a) Model Name: M236H1 –P01

(b) Carton ID: CMO internal control

(c) Quantities: 27 pcs

Version 2.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc. No.:

Issued Date: Nov.13, 2008

Model No.: M236H1-P01

Approval

10. PRECAUTIONS

10.1 ASSEMBLY AND HANDLING PRECAUTIONS

(1) Do not apply rough force such as bending or twisting to the product during assembly.

(2) To assemble backlight or install module into user’s system can be only in clean working areas. The

dust and oil may cause electrical short or worsen the polarizer.

(3) It is not permitted to have pressure or impulse on the module because the LCD panel will be

damaged.

(4) Always follow the correct power sequence when the product is connecting and operating. This can

prevent damage to the CMOS LSI chips during latch-up.

(5) Do not pull the I/F connector in or out while the module is operating.

(6) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and

easily scratched.

(7) It is dangerous that moisture come into or contacted the product, because moisture may damage the

product when it is operating.

(8) High temperature or humidity may reduce the performance of module. Please store this product within

the specified storage conditions.

(9) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the

response time will become slowly.

10.2 SAFETY PRECAUTIONS

(1) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In

case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.

(2) After the product’s end of life, it is not harmful in case of normal operation and storage.

10.3 OTHER

When fixed patterns are displayed for a long time, remnant image is likely to occur.

11. MECHANICAL DRAWING

23 / 24

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 2.0

www.panelook.com

CMO M236H1-P01 Specification

Specifications and Main Features

Frequently Asked Questions

User Manual