6 Color / Chromaticity Coordinates (CIE) Color / Chromaticity Coordinates (CIE)
Revise “VDD min.”
12
Revise “VDD max.”
14
document version0.4 3
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
22
Revise “Timing Diagram”
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
document version0.4 4
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the LED lightbar edge. Instead, press at the
far ends of the LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
13) Please avoid touching COF contact while handling or fitting the TFT module into your system.
14) When storing modules as spares for a long time, the following precaution is necessary:
Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep
the temperature between ˈкʳ ˴˷ʳˆˈкʳ ˴ʳ˴˿ʳ˻˼˷˼ˁ
document version0.4 5
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
2.0 General Description
This specification applies to the 18.5 inch-wide Color a-Si TFT-LCD ModuleM185XTN01.The
display supports the WXGA - 1366(H) x 768(V) screen format and16.7M colors (RGB 6-bits +
Hi-FRC data). All input signals are 1-channel LVDS interface and this module doesn’t contain an
inverter board for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25к condition:
ITEMS Unit SPECIFICATIONS
Screen Diagonal [mm]
Active Area [mm] 409.8 (H) x 230.4 (V)
Pixels H x V 1366(x3) x 768
Pixel Pitch [um] 300 (per one triad) × 300
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode, Normally White
White Luminance ( Center ) [cd/m2]
Contrast Ratio 1000 (Typ.)
Optical Response Time [msec] 5ms (Typ., on/off)
Nominal Input Voltage VDD [Volt] +5.0 V (Typ)
Power Consumption
[Watt]
(VDD line + LED line)
Weight [Grams]
Physical Size [mm] 430.4 (W) x 254.6 (H) Typ. x 9.9 (D) Typ
Interface One channel LVDS
Support Color 16.7M colors (RGB 6-bit + Hi_FRC )
Surface Treatment Anti-Glare, 3H
Temperature Range
Operating
Storage (Shipping)
o
[
C]
o
[
C]
TCO6.0 Compliance Yes
470.1(18.51”)
250 cd/m
VDD line: PDD (typ)= 1.75W, All black pattern at 60Hz
LED line : PBLU (typ) = 7.2W
Total : 8.95W
2
(Typ.)
ʳ
12907\S
0 to +50
-20 to +60
document version0.4 6
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
M185XTN01.2
AU OPTRONICS CORPORATION
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25к:
Item Unit Conditions Min. Typ. Max. Note
Horizontal (Right)
CR = 10 (Left)
Viewing Angle [degree]
Vertical (Up)
CR = 10 (Down)
Contrast ratio Normal Direction
Raising Time (TrR)
Response Time [msec]
Falling Time (TrF)
Raising + Falling
Red x
Red y
Color / Chromaticity
Coordinates (CIE)
Green x
Green y
Blue x
Blue y
Color Coordinates (CIE) White
White x
White y
Central Luminance [cd/m2] 200 250 - 6
Luminance Uniformity
Crosstalk (in 60Hz)
Flicker
[%]
[%]
dB
75
75
70
70
600
-
-
-
0.616 0.646 0.676
0.303 0.333 0.363
0.287 0.317 0.347
0.595 0.625 0.655
0.124 0.154 0.184
0.031 0.061 0.091
0.283 0.313 0.343
0.299 0.329 0.359
75 80
85
85
80
80
1000 -
3.6 -
1.4 -
5 -
1.5 8
-20
-
-
-
-
-
2
3
4
5
7
9
document version0.4 7
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
Note 1: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring (at surface 35
. In order to stabilize the luminance, the
measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and
dark room. ʳ
Photo detector
Measured distance
-
Note 2: Definition of viewing angle measured by ELDIM (EZContrast 88)
Viewing angle is the measurement of contrast ratio Њ10, at the screen center, over a 180°
horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is
broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low
(down). The measurement direction is typically perpendicular to the display surface with the screen
rotated about its center to develop the desired measurement viewing angle.
Center of the screen
document version0.4 8
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
Note 8:Crosstalk is defined as below and measured by TOPCON SR-3
CT = | YB – YA | / YA Ø 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
M185XTN01.2
Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3
R G B R G B
Gray Level = L127
R G B R G B
R G B R G B
Gray Level = L0
Method: Record dBV & DC value with TRD-100
Amplitude
DC
AC
Time
Hz) 30Level(at AC
log20(dB)Flicker =
Level DC
document version0.4 10
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Y
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
3.0 Functional Block Diagram
The following diagram shows the functional block of the18.5 inch Color TFT-LCD Module:
LVDS
+5V
LVDS
Receiver
Connector
AUO
ASIC
Timing
Controller
mini
Transmitter
G1
-Driver IC
1366(x3) x 768
G768
D1 D4098
TFT-LCD
Pixels
X-Driver IC
LED
DC/DC
Converter
I/F + X-PCB
Gamma
Correction
DC
I/F PCB Interface:
MSCKT2407P30HB (STM) / AL230F-A0G1D-P (P-TWO)
Mating Type:
FI-X30HL(JAE) (Locked Type)
FI-X30H (JAE)(Unlocked Type)
Driver
document version0.4 11
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
4.0 Absolute Maximum Ratings
Absolute maximum ratings of the module are as following:
4.1 TFT LCD Module
Item Symbol Min Max Unit Conditions
Logic/LCD Drive
Voltage
4.2 Backlight Unit
Item Symbol Min Max Unit Conditions
LED ˙orward Current
LED ˣ˿˸ Forward Current
VDD -0.3 +7/1 [Volt] Note 1,2
IRLED1
IRLED2
IRLED3
IRLED4
IPLED1
IPLED2
IPLED3
IPLED4
0 90
- 150
[mA]
[mA]
M185XTN01.2
Note 1,2,5
100% duty
Note 1,2,5
10% duty @100Hz
LED forward Voltage variation
(per string variation)
ӔVf
- 3.4
[Volt]
Note 1,2
4.3 Absolute Ratings of Environment
Item Symbol Min. Max. Unit Conditions
Operating Temperature TOP 0 +50 [oC] Note 3
Glass surface temperature
(operation)
Operation Humidity HOP 5 90 [%RH]
Storage Temperature TST -20 +60 [oC]
Storage Humidity HST
Note 1: With in Ta (25к)
Note 2: Permanent damage to the device may occur if exceeding maximum values
Note 3: Temperature and relative humidity range are shown as the below figure.
1. 90% RH Max ( Taʳ Љˆˌкʼʳ
2. Max wet-bulb temperature at 39кʳ ʳ˿˸ˁʳʻʳ˧˴ʳ Љˆˌкʼʳ
ʳʳʳʳʳʳʳʳˆˁʳˡʳ˶˷˸˴˼ʳ
Note 4: Function Judged only
Note 5: IRLED1,2,3,4 and IPLED1,2,3,4 define as per strings LED current.
TGS 0 +65 [
5 90
o
C] Note 3, Note 4
Note 3
[%RH]
document version0.4 12
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Operating Range
Product Specification
AU OPTRONICS CORPORATION
Storage Range
M185XTN01.2
document version0.4 13
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
M185XTN01.2
AU OPTRONICS CORPORATION
5.0 Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as following:
Symbol Parameter Min Typ Max Unit Conditions
VDDLogic/LCD Drive Voltage 4.5
-
IDDInput Current
-
PDD
VDD Power
-
-
5.0
5.5
[Volt]+/-10%
0.35
0.42
[A]VDD= 5.0V, All Black Pattern At 60Hz,
0.42 0.5 VDD= 5.0V, All Black Pattern At 75Hz
1.75 2.1 [Watt] VDD= 5.0V, All Black Pattern At 60Hz
2.1 2.5 VDD= 5.0V, All Black Pattern At 75Hz
IRush Inrush Current
VDDrp
Allowable Logic/LCD
Drive Ripple Voltage
-
-
Note 1: Measurement conditions:
The duration of rising time of power input is 470us.
+5.0V
R1
47K
(High to Low)
Control
Signal
SW1
SW MAG-SPST
12
+12.0V
C2
1uF/25V
R2
1K
VR1
47K
C3
0.01uF/25V
- TBD [A] Note 1
- 350 [mV] p-p VDD= 5.0V, All Black Pattern At 75Hz
Q3
AO6402
D6
D5
D2S
D1
G
D2SD1D5
D6
G
Q3
AO6402
F1
VCC
C1
1uF/16V
(LCD Module Input)
document version0.4 14
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
M185XTN01.2
AU OPTRONICS CORPORATION
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when VDD is off. Please refer to specifications of
SN75LVDS82DGG (Texas Instruments) in detail.
1. DC Characteristics of each signal are as following:
SymbolParameterMinTypMaxUnitsCondition
VTH
VTL
ūVIDūInput Differential Voltage 100 - 600 [mV] Note 1
VCM
Differential Input High
Threshold
Differential Input Low
Threshold
Differential Input Common
Mode Voltage
- - +100 [mV]
-100 - - [mV]
+1.0 +1.2 +1.5 [V]
VCM = 1.2V
Note1
VCM = 1.2V
Note 1
VTH-VTL = 200MV (max)
Note1
Note 1: LVDS Signal Waveform
document version0.4 15
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
r
V
www.panelook.com
2. AC Characteristics
Description Symbol Min Max Unit Note
Maximum deviation of input
clock frequency during SSC
Maximum modulation frequency
of input clock during SSC
Freq
F
max
Product Specification
AU OPTRONICS CORPORATION
FDEV -
FMOD - 200 KHz
3
%
M185XTN01.2
Fcenter * FDE
Fcente
Fmin
1
F
MOD
< Spread Spectrum>
time
document version0.4 16
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
5.2 Backlight Unit
Parameter guideline for LED driving is under stable conditions at 25к (Room Temperature):
Symbol Description Min.
IRLED1
IRLED2
LED Operation Current 67 70 73 [mA] Note 1
IRLED3
IRLED4
VLED Light Bar Operation Voltage 24 25.6 27.2 [Volt] Note 2
PBLU BLU Power Consumption 6.4 7.2 7.9 [Watt] Note 3
Typ. Max. Unit Note
LTLED LED Life Time (Typical) 30,000- - [Hour] Note 4
Each module consists of 32 pcs LED ( 4 strings x 8 pcs / string )
Note 1 : The specified current is 100% duty of LED chip input current, IRLED1,2,3,4 define as per
strings LED current.
Note 2 : The value showed in the table is one light bar’s operation voltage.
15 RXCLKIN+ Positive LVDS differential data input (clock)
16 GND Power Ground
17 RXIN3- Negative LVDS differential data input (3)
18 RXIN3+ Positive LVDS differential data input (3)
19 GND Power Ground
20 NC No contact (For AUO internal use)
21 NC No contact (For AUO internal use)
22 NC No contact (For AUO internal use)
23 GND Power Ground
24 GND Power Ground
25 GND Power Ground
26 VDD +5V power supply
27 VDD +5V power supply
28 VDD +5V power supply
29 VDD +5V power supply
30 VDD +5V power supply
document version0.4 19
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
document version0.4 20
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
6.4 Timing Characteristics
Basically, interface timing described here is not actual input timing of LCD module but close to
output timing of SN75LVDS82DGG (Texas Instruments) or equivalent.
SignalItemSymbolMinTypMaxUnit
Period Tv 776 808 1023 Th
Active Tdisp(v) 768768768Th
V-section
Blanking Tblk(v) 840255Th
Period Th 1416ʳ1606 2047 Tclk
Active Tdisp(h) 136613661366Tclk
H-section
Blanking Tblk(h) 50240681Tclk
Period Tclk - 12.8 - ns
˖˿˶˾
˖˿˶˾ʳʳʳʳ
˖˿˶˾˖˿˶˾
˙˴˸ʳ˥˴˸
˙˴˸ʳ˥˴˸ʳʳʳʳ
˙˴˸ʳ˥˴˸˙˴˸ʳ˥˴˸
Frequency Freq 557890MHz
Frame
Rate
F
50 60 75 Hz
Note1 : DE mode only
Note2 : Clock Frequency 90MHz(Max.)= 1416(H)*847(V)*75Hz
document version0.4 21
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
6.5 Timing diagram
Product Specification
M185XTN01.2
AU OPTRONICS CORPORATION
document version0.4 22
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
6.6 Power ON/OFF Sequence
VDD power and lamp on/off sequence are as follows. Interface signals are also shown in the
chart. Signals from any system shall be Hi-Z state or low level when VDD is off.
T1
Power Supply VDD
LVDS Signal
90%
10%
T2
VALID
DATA
90%
T5
T6
10%
T7
T3
Backlight On
T4
Power Sequence Timing
Value
Parameter
Min. Typ. Max.
T1 0.5 - 10 [ms]
T2 0 - 50 [ms]
T3 500 - - [ms]
T4 100 - - [ms]
T5 0 50
T6 5 - 100
T7 1000 - - [ms]
Note1 : Recommend setting T5 = 0ms to avoid electronic noise when VDD is off.
Note2 : During T5 and T6 period , please keep the level of input LVDS signals with Hi-Z state.
Unit
[ms]
Note1,2
[ms]
Note1,2
document version0.4 23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M185XTN01.2
7.0 Connector & Pin Assignment
Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.
7.1 TFT LCD Module
Connector Name / Designation Interface Connector / Interface card
Manufacturer STM or P-TWO
MSCKT2407P30HB (STM) / AL230F-A0G1D-P
Type Part Number
Mating Housing Part Number
(P-TWO)
FI-X30HL(JAE) (Locked Type)
FI-X30H (JAE)(Unlocked Type)
7.1.1 Pin Assignment
Pin#Signal Name Pin#Signal Name
1 NC 2 NC
3 NC 4 GND
5
7
9
11
13
15
17
19
RXIN0-
GND
RXIN1+
RXIN2-
GND
RXCLKIN+
RXIN3-
GND
6
8
10
12
14
16
18
20 NC
21 NC 22 NC
23
25
GND
GND
24
26 VDD
RXIN0+
RXIN1-
GND
RXIN2+
RXCLKIN-
GND
RXIN3+
GND
27 VDD 28 VDD
29 VDD 30 VDD
document version0.4 24
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
7.2 LED Connector on Backlight Unit.
This connector is mounted on LED light-bar.
Connector Name / Designation Light Bar Connector
Manufacturer
Mating Type Part Number
7.2.1 LED Pin assignment
Pin# Signal Name
ENTERY (E&T) Corporationʳ
3707K-Q06N-01R (Wire harness)
M185XTN01.2
1 IRLED1 (current out)
2 IRLED2 (current out)
3 VLED (voltage in)
4 VLED (voltage in)
5 IRLED3 (current out)
6 IRLED4 (current out)
document version0.4 25
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
7.2.2 LED Connector dimension
Product Specification
AU OPTRONICS CORPORATION
)(0.1,25.400.39.13mmunitPitchDVH==××=××
)(0.1,25.400.39.13mmunitPitchDVH==××=××
M185XTN01.2
7.2.3 LED Mating housing dimension
document version0.4 26
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
8.0 Reliability Test
Environment test conditions are listed as following table.
Items Required Condition
Temperature Humidity Bias (THB)
High Temperature Operation (HTO)
Low Temperature Operation (LTO)
High Temperature Storage (HTS)
Low Temperature Storage (LTS)
Vibration Test
(Non-operation)
Ta= 50
Ta= 50
Ta= 0
Ta= 60
Ta= -20
Acceleration: 1.5 Grms
Wave: Random
Frequency: 10 - 200 Hz
Duration: 30 Minutes each Axis (X, Y, Z)
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-2˃к to 6˃к, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: EN61000-4-2, ESD class B:
Certain performance degradation allowed
No data lost
Self-recoverable
No hardware failures.
document version0.4 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
9.0 Shipping Label
The label is on the panel as shown below:
Manufactured: XX/XX
Model No: M185XTN01.2
AU Optronics
Made in XXXXX
M185XTN01.2
Note 1: For Pb Free products, AUO will add
Note 2: For RoHS compatible products, AUO will add
Note 3: For China RoHS compatible products, AUO will add
for identification.
for identification.
for identification.
Note 4: The Green Mark will be presented only when the green documents have been ready by
AUO Internal Green Team.
document version0.4 28
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
M185XTN01.2
AU OPTRONICS CORPORATION
Product Specification
10.0 Mechanical Characteristics
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
document version0.4 29
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
M185XTN01.2
AU OPTRONICS CORPORATION
Product Specification
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
document version0.4 30
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
M185XTN01.2
AU OPTRONICS CORPORATION
Product Specification
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
document version0.4 31
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
11. Packing Specification
M185 14ׂᇘ
றᇆ
றᇆ:
றᇆறᇆ
Carton:81.18M02.008 /Cushion:84.18M02.037
ലM185ᑓิᆜԵᙩሽխࠀމᦤ৵
ࠉݧ࣋Եץᇘሶࣨխ
ׂᇘ:48.5*37.2*34.8cm
ׂᇘׂᇘ
M185XTN01.2
࣋ᆜ14ׂΔ࣋ԵՂ።ᒷᓢΔᒣݙګ
document version0.4 32
ᐋ
ᐋ pallet ؚཥقრቹ
ᐋᐋ
ؚཥقრቹ
ؚཥقრቹؚཥقრቹ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
M185XTN01.2
AU OPTRONICS CORPORATION
Pallet and shipment information
Q'ty Dimension Weight(kg)
1 Panel 1 430.37(H)mm x 254.6(V)mm x 9.9(D)mm1.330
2 Cushion 1 -
3 Box 1 485(L)mm x 372(W)mm x 348(H)mm 1.00 without Panel & cushion
4 Packing Box 14 pcs/Box 485(L)mm x 372(W)mm x 348(H)mm 20.745 with panel & cushion
Item
5 Pallet 1
6 Pallet after Packing
2ˇ boxes/pallet 1150(L)mm x ˌˋ0(W)mm x 138(H)mm
1150(L)mm x ˌˋ0(W)mm x 138(H)mm
Specification
Remark
1.˄˅ˈ
15
509
document version0.4 33
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.