CMO M185B1-L03 Specification

Global LCD Panel Exchange Center

ಖᙕ

ՠ܂

ᐉு

ߡۥ

ދป

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

TFT LCD Preliminary Specification

MODEL NO.: M185B1-L03

Customer:

Approved by:

Note:



2008-09-12

PMMD II



kevin_wu(ܦᕬ



Director Accept

14:53:10 CST

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Director

/56520/54894)

1 / 25



Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

- CONTENTS -

REVISION HISTORY ............................................................................................................................... 3

1. GENERAL DESCRIPTION .................................................................................................................. 4

1.1 OVERVIEW

1.2 FEATURES

1.3 APPLICATION

1.4 GENERAL SPECIFICATIONS

1.5 MECHANICAL SPECIFICATIONS

2. ABSOLUTE MAXIMUM RATINGS ....................................................................................................... 5

2.1 ABSOLUTE RATINGS OF ENVIRONMENT

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE

2.2.2 BACKLIGHT UNIT

3. ELECTRICAL CHARACTERISTICS .................................................................................................... 7

3. 1.1 TFT LCD MODULE

3.1.2 Vcc Power Dip Condition:

3.2 BACKLIGHT UNIT

4. BLOCK DIAGRAM ............................................................................................................................... 11

4.1 TFT LCD MODULE

4.2 BACKLIGHT UNIT

5. INPUT TERMINAL PIN ASSIGNMENT................................................................................................ 12

5.1 TFT LCD MODULE

5.2 LVDS DATA MAPPING TABLE

5.3 BACKLIGHT UNIT

5.4 COLOR DATA INPUT ASSIGNMENT

6. INTERFACE TIMING ...........................................................................................................................15

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

6.2 POWER ON/OFF SEQUENCE

7. OPTICAL CHARACTERISTICS........................................................................................................... 17

7.1 TEST CONDITIONS

7.2 OPTICAL SPECIFICATIONS

8. PACKAGING ........................................................................................................................................ 21

8.1 PACKING SPECIFICATIONS

8.2 PACKING METHOD

9. DEFINITION OF LABELS .................................................................................................................... 23

10. PRECAUTIONS ................................................................................................................................. 24

10.1 ASSEMBLY AND HANDLING PRECAUTIONS

10.2 SAFETY PRECAUTIONS

11. MECHANICAL CHARACTERISTICS ................................................................................................. 25

2 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

REVISION HISTORY

Version Date Section Description

Ver 1.0 Aug.12, 08’ M185B1-L03 Preliminary specification was first issued.

3 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

1. GENERAL DESCRIPTION

1.1 OVERVIEW

M185B1-L03 is a 18.5” TFT Liquid Crystal Display module with 2 CCFL Backlight unit and 30pin

1ch-LVDS interface. This module supports 1366 x 768 WXGA mode and can display up to 16.7M colors.

The inverter module for Backlight is not built in.

1.2 FEATURES

- Contrast ratio 1000:1

- Response time 5ms.

- Brightness 300nits

- Color saturation NTSC 72%.

- WXGA (1366 x 768 pixels) resolution.

- DE (Data Enable) only mode.

- LVDS (Low Voltage Differential Signaling) interface.

- RoHS compliance.

1.3 APPLICATION

- TFT LCD Monitor

1.4 GENERAL SPECIFICATI0NS

Item Specification Unit Note

Active Area 409.8 (H) × 230.4(V) (18.5” diagonal) mm

Bezel Opening Area 413.4(H) x 234 (V) mm

Driver Element a-Si TFT active matrix - -

Pixel Number 1366 x R.G.B. x 768 pixel -

Pixel Pitch 0.3 (H) x 0.3 (V) mm -

Pixel Arrangement RGB vertical stripe - -

Display Colors 16.7M color -

Transmissive Mode Normally White - -

Surface Treatment AG type, 3H hard coating, Haze 25 - -

Module Power Consumption 13.85 Watt (2)

Note (2) Please refer to sec. 3.1 & 3.2 in this document for more information of power consumption.

(1)

1.5 MECHANICAL SPECIFICATIONS

Item Min. Typ. Max. Unit Note

Horizontal(H) 429.87 430.37 430.87 mm

Module Size

Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.

Vertical(V) 254.1 254.6 255.1 mm

Depth(D) 15.75 16.25 16.75 mm

Weight - 1965 2000 g -

4 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

(1)

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

A

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT

Item Symbol

Storage Temperature TST -20 60 ºC (1)

Operating Ambient Temperature TOP 0 50 ºC (1), (2)

Shock (Non-Operating) S

Vibration (Non-Operating) V

Note (1) Temperature and relative humidity range is shown in the figure below.

(a) 90 %RH Max. (Ta Љ 40 ºC).

(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).

(c) No condensation.

Note (2) The temperature of panel display surface area should be 0 ºC Min. and 60 ºC Max.

- 50 G (3), (5)

NOP

- 1.5 G (4), (5)

NOP

Min. Max.

Value

Unit Note

Relative Humidity (%RH)

100

90

80

60

Operating Range

40

20

10

Storage Range

8060-20 400 20-40

Temperature (C)

Note (3) 50G,11ms, half sine wave, 1 time for ± X, ± Y, ± Z.

Note (4) 10 ~ 300 Hz, 10min/cycle, 3 cycles each X, Y, Z.

Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough

so that the module would not be twisted or bent by the fixture.

The fixing condition is shown as below:

t Room Temperature

Side Mount Fixing Screw

Gap=2mm

Bracket

LCD Module

Side Mount Fixing Screw

Stage

5 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE

Item Symbol

Power Supply Voltage Vcc -0.3 +6.0 V (1)

Min. Max.

2.2.2 BACKLIGHT UNIT

Item Symbol

Lamp Voltage VL - 2.5K V Lamp Current IL 2.0 8.0 mA

Lamp Frequency FL 40 80 KHz

Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation

should be restricted to the conditions described under Normal Operating Conditions.

Min. Max.

Value

Unit Note

(1), (2), IL = 7.0mA

RMS

(1), (2)

Note (2) Specified values are for lamp (Refer to 3.2 for further information).

6 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc No.:

Issued Date: Aug. 12, 2008

Model No.: M185B1-L03

Preliminary

3. ELECTRICAL CHARACTERISTICS

3.1.1 TFT LCD MODULE Ta = 25 ± 2 ºC

Parameter Symbol

Min. Typ. Max.

Power Supply Voltage Vcc 4.5 5.0 5.5 V -

Ripple Voltage VRP - - 100 mV -

Rush Current I

RUSH

- 2 3 A (2)

White - 0.44 0.6 A (3)a

Power Supply Current

Black - 0.58 0.9 A (3)b

Vertical Stripe

lcc

- 0.6 0.9 A (3)c

Power Consumption - 3.0 4.5 Watt (4)

LVDS differential input voltage Vid 100 - 600 mV

LVDS common input voltage Vic - 1.2 - V

Note (1) The module should be always operated within above ranges.

Note (2) Measurement Conditions:

Value

Unit Note

(High to Low)

(Control Signal)

SW

+12V

+5.0V

R1

47K

R2

1K

47K

VR1

C1

1uF

Q1 2SK1475

C2

0.01uF

Q2

2SK1470

FUSE

C3

1uF

Vcc

(LCD Module Input)

Vcc rising time is 470Ps

Vcc

0.9Vcc

0.1Vcc

GND

470Ps

7 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

Note (3) The specified power supply current is under the conditions at Vcc = 5.0 V, Ta = 25 ± 2 ºC, f

Hz, whereas a power dissipation check pattern below is displayed.

a. White Pattern

Active Area

c. Vertical Stripe Pattern

b. Black Pattern

Active Area

R

G

R

B

G

B

R

G

B

R

= 60

v

R

B

R R

Active Area

Note (4) The power consumption is specified at the pattern with the maximum current.

3.1.2 Vcc Power Dip Condition:

Vcc

G

B

R

4.5V

4.0V

Td

Dip condition:

msTdVVccV 20,5.40.4 ddd

G

B

R

8 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc No.:

Issued Date: Aug. 12, 2008

Model No.: M185B1-L03

Preliminary

3.2 BACKLIGHT UNIT Ta = 25 ± 2 ºC

Parameter Symbol

Min. Typ. Max.

Lamp Input Voltage VL --- 775 853 V

Lamp Current IL 2.0 7.0 8.0 mA

Lamp Turn On Voltage V

S

--- ---

Operating Frequency FL 40 55 80 KHz (3)

Lamp Life Time LBL 40000 --- --- Hrs (5), IL= 7.5mA

Power Consumption PL --- 10.85 --- W (4), IL = 7.5 mA

Note (1) Lamp current is measured by current amplify & oscilloscope as shown below:

+

ΗΗΗΗ

-

Value

Unit Note

1680(0к)

1460(25к)

I

RMS

V

(2)

RMS

(2)

V

RMS

= 7.0 mA

L

(1)

ΗΗΗΗ

LCD

Module

Inverter

Current Amplify

Oscilloscope

+

Current

Probe

Measure equipment: Current Amplify: Tektronix TCPA300 Current probe: Tektronix TCP312 Oscilloscope: TDS3054B

Note (2) The voltage that must be larger than Vs should be applied to the lamp for more than 1 second

after startup. Otherwise, the lamp may not be turned on normally. It is the value output voltage of

NF circuit.

Note (3) The lamp frequency may produce interference with horizontal synchronization frequency from the

display, which might cause line flow on the display. In order to avoid interference, the lamp

frequency should be detached from the horizontal synchronization frequency and its harmonics as

far as possible.

Note (4) P

 VL 2 (for 2 lamps)

= I

L

Note (5) The lifetime of lamp can be defined as the time in which it continues to operate under the condition

Ta = 25 2

o

C and( IL = 7.0 mArms )until one of the following events occurs:

(a) When the brightness becomes Љ 50% of its original value.

(b) Effective lighting length decreases 80% under for initial. (Effective lighting length is a scope of

luminance 80% over for average luminance at several point in lamp center.)

Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the

inverter must have specifications for the modularized lamp. The performance of the Backlight,

such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for

9 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

the lamp. All the parameters of an inverter should be carefully designed to avoid producing too

much current leakage from high voltage output of the inverter. When designing or ordering the

inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the

inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module

should be operated in the same manners when it is installed in your instrument.

The output of the inverter must have symmetrical (negative and positive) voltage waveform and

symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter

which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may

produce interface with horizontal synchronous frequency and as a result this may cause beat on the

display. Therefore lamp frequency shall be as away possible from the horizontal synchronous

frequency and from its harmonics in order to prevent interference.

Requirements for a system inverter design, which is intended to have a better display performance, a

better power efficiency and a more reliable lamp. It shall help increase the lamp lifetime and reduce its

leakage current.

a. The asymmetry rate of the inverter waveform should be 10% below;

b. The distortion rate of the waveform should be within Ѕ2 ± 10%;

c. The ideal sine wave form shall be symmetric in positive and negative polarities

* Asymmetry rate:

I p

I -p

| I

* Distortion rate

I

– I –p | / I

p

(or I –p) / I

p

rms

* 100%

10 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc No.:

Issued Date: Aug. 12, 2008

Model No.: M185B1-L03

Preliminary

4. BLOCK DIAGRAM

4.1 TFT LCD MODULE

SCAN DRIVER IC

LVDS INPUT /

TIMING CONTROLLER

TFT LCD PANEL

(1366x3x768)

DATA DRIVER IC

RX0(+/-)

RX1(+/-)

RX2(+/-)

RX3(+/-)

RXC(+/-)

NC

(STM MSAKT2407P30A

INPUT CONNECTOR

or EQUIVALENT)

GND

Vcc

VL

LAMP CONNECTOR

(YEONHO 35001HS-02L)

4.2 BACKLIGHT UNIT

DC/DC CONVERTER &

REFERENCE VOLTAGE

BACKLIGHT UNIT

1 HV(Pink)

2 LV(White)

1 HV(Pink)

11 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

2 LV(White)

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

5. INPUT TERMINAL PIN ASSIGNMENT

5.1 TFT LCD MODULE

Pin Name Description

1 NC Not connection, this pin should be open. 2 NC Not connection, this pin should be open. 3 NC Not connection, this pin should be open. 4 GND Ground 5 RX0- Negative LVDS differential data input. Channel 0 6 RX0+ Positive LVDS differential data input. Channel 0 7 GND Ground 8 RX1- Negative LVDS differential data input. Channel 1

9 RX1+ Positive LVDS differential data input. Channel 1 10 GND Ground 11 RX2- Negative LVDS differential data input. Channel 2 12 RX2+ Positive LVDS differential data input. Channel 2 13 GND Ground 14 RXCLK- Negative LVDS differential clock input. 15 RXCLK+ Positive LVDS differential clock input. 16 GND Ground 17 RX3- Negative LVDS differential data input. Channel 3 18 RX3+ Positive LVDS differential data input. Channel 3 19 GND Ground 20 NC Not connection, this pin should be open. 21 NC Not connection, this pin should be open. 22 NC Not connection, this pin should be open. 23 GND Ground 24 GND Ground 25 GND Ground 26 Vcc +5.0V power supply 27 Vcc +5.0V power supply 28 Vcc +5.0V power supply 29 Vcc +5.0V power supply 30 Vcc +5.0V power supply

Note (1) Connector Part No.: STM MSAKT2407P30A or equivalent

12 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

5.2 LVDS mapping table

LVDS Channel 0

LVDS Channel 1

LVDS Channel 2

LVDS Channel 3

LVDS output D7 D6 D4 D3 D2 D1 D0 Data order G0 R5 R4 R3 R2 R1 R0 LVDS output D18 D15 D14 D13 D12 D9 D8 Data order B1 B0 G5 G4 G3 G2 G1 LVDS output D26 D25 D24 D22 D21 D20 D19 Data order DE NA NA B5 B4 B3 B2 LVDS output D23 D17 D16 D11 D10 D5 D27 Data order NA B7 B6 G7 G6 R7 R6

5.3 BACKLIGHT UNIT:

Pin Symbol Description Remark

1 HV High Voltage Pink 2 LV Low Voltage White

Note (1) Connector Part No.: YEONHO 35001HS-02L or equivalent

13 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

5.4 COLOR DATA INPUT ASSIGNMENT

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for

the color. The higher the binary input, the brighter the color. The table below provides the assignment of

color versus data input.

Data Signal

Basic

Colors

Gray

Scale

Of

Red

Color

Black

Red

Green

Blue

Cyan

Magenta

Yellow

White

Red(0) / Dark

Red(1) Red(2)

Red(253) Red(254) Red(255)

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

0

1

0

1

0

:

1

Red Green Blue

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

:

1

0

1

0

1

0

1

0

1

0

1

0

:

0

1

0

1

0

:

0

Green(0) / Dark

Green(1)

Gray

Scale

Of

Green

Gray

Scale

Of

Blue

Note (1) 0: Low Level Voltage, 1: High Level Voltage

Green(2)

Green(253) Green(254) Green(255)

Blue(0) / Dark

Blue(1) Blue(2)

Blue(253) Blue(254) Blue(255)

0

:

0

:

0

1

0

1

0

:

0

1

0

1

0

1

0

1

0

1

0

1

0

:

0

1

0

1

0

1

0

1

14 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

6. INTERFACE TIMING

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

The input signal timing specifications are shown as the following table and timing diagram.

Signal Item Symbol Min. Typ. Max. Unit Note

Frequency Fc 50.0 76 95 MHz -

LVDS Clock

LVDS Da t a

Vertical Active Display Term

Horizontal Active Display Term

Note: Because this module is operated by DE only mode, Hsync and Vsync input signals should be set

Period Tc 10.5 13.2 20 ns High Time Tch - 4/7 - Tc Low Time Tcl - 3/7 - Tc Setup Time Tlvs 600 - - ps Hold Time Tlvh 600 - - ps Frame Rate Fr 40 60 75 Hz Tv=Tvd+Tvb Total Tv 778 806 888 Th Display Tvd 768 768 768 Th Blank Tvb Tv-Tvd 38 Tv-Tvd Th Total Th 1446 1560 1936 Tc Th=Thd+Thb Display Thd 1366 1366 1366 Tc Blank Thb Th-Thd 194 Th-Thd Tc -

to low logic level or ground. Otherwise, this module would operate abnormally.

INPUT SIGNAL TIMING DIAGRAM

DE

Th

DCLK

T

DE

DATA

C

Thb

hd

T

15 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc No.:

Issued Date: Aug. 12, 2008

Model No.: M185B1-L03

Preliminary

6.2 POWER ON/OFF SEQUENCE

To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the

diagram below.

Power Supply

for LCD, Vcc

0V

- Interface Signal

(LVDS Signal of Transmitter), V

0V

I

- Power for Lamp

Timing Specifications:

0.5< t1 Љ 5 msec

0 < t2 Љ 50 msec

0 < t3 Љ 50 msec

t4 Њ 500 msec

Power On

90%

10%

Restart

10%

t4

Power Off

90%

t1

t3t2

Valid Data

t6t5

50%50%

ONOFF OFF

t5 Њ 450 msec

t6 Њ 90 msec

Note.

(1) The supply voltage of the external system for the module input should be the same as the definition of Vcc.

(2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD

operation of the LCD turns off, the display may momentarily become abnormal screen.

(3) In case of VCC = off level, please keep the level of input signals on the low or keep a high impedance.

(4) T4 should be measured after the module has been fully discharged between power off and on period.

(5) Interface signal shall not be kept at high impedance when the power is on.

(6)

The company will not guarantee or compensate for the product damage caused by not following the Power

Sequence.

16 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc No.:

Issued Date: Aug. 12, 2008

Model No.: M185B1-L03

Preliminary

7. OPTICAL CHARACTERISTICS

7.1 TEST CONDITIONS

Item Symbol Value Unit

Ambient Temperature Ta 25±2

Ambient Humidity Ha 50±10 %RH

Supply Voltage VCC 5V V

Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"

Lamp Current I

L

7.0 ± 0.5 mA

Inverter Operating Frequency FL 55±5 KHz

Inverter

Logah MIT70070.50

7.2 OPTICAL SPECIFICATIONS

The relative measurement methods of optical characteristics are shown in 7.2. The following items should

o

C

be measured under the test conditions described in 7.1 and stable environment shown in Note (5).

Item Symbol Condition Min. Typ. Max. Unit Note

Red

Color

Green

Chromaticity

(CIE 1931)

Blue

White

Center Luminance of White

(Center of Screen)

Contrast Ratio CR

Response Time

White Variation

Horizontal

Viewing Angle

Vertica l

Rx

Ry

Gx Gy Bx

By

=0q, TY =0q

T

x

CS-1000T

Typ -

0.03

Wx

Wy

L

C

250 300 - cd/m2(4), (5)

700 1000 - - (2), (5)

TR - 1.3 3.2

T

F

GW

Tx+

T

-

x

TY+

T

-

Y

T

=0q, TY =0q

x

T

=0q, TY =0q

x

USB2000

CR Њ 10

USB2000

75 75 70

70

0.646

0.334

0.284

0.602

0.152

Typ +

0.03

- (1), (5)

0.076

0.313

0.329

- 3.7 6.8

ms (3)

- 1.3 1.5 - (5), (6)

85 85 80 80

Deg. (1), (5)

-

17 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

y

www.panelook.com

Doc No.:

Issued Date: Aug. 12, 2008

Model No.: M185B1-L03

Preliminary

Note (1) Definition of Viewing Angle (Tx, Ty):

Normal

TX- = 90º

6 o’clock

T

- = 90º

x-

y-

Note (2) Definition of Contrast Ratio (CR):

The contrast ratio can be calculated by the following expression.

Contrast Ratio (CR) = L255 / L0

L255: Luminance of gray level 255

L 0: Luminance of gray level 0

Tx = T

= 0º

Ty- Ty

Tx

Tx

12 o’clock direction

y+

T

+ = 90º

x+

TX+ = 90º

CR = CR (5)

CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).

Note (3) Definition of Response Time (T

Gray Level 255

100%

90%

Optical

Response

10%

0%

66.67ms 66.67ms

T

, TF):

R

Gray Level 0

Gray Level 255

T

F

18 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

500

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

Note (4) Definition of Luminance of White (LC):

Measure the luminance of gray level 255 at center point

L

= L (5)

C

L (x) is corresponding to the luminance of the point X at Figure in Note (6).

Note (5) Measurement Setup:

The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt

temperature change during measuring. In order to stabilize the luminance, the measurement

should be executed after lighting Backlight for 20 minutes in a windless room.

LCD Module

LCD Panel

USB2000

Center of the Screen

Note (6) Definition of White Variation (GW):

Measure the luminance of gray level 255 at 9 points

GW = Maximum [L (1), L (2) ……L (4), L (9)] / Minimum [L (1), L (2) …… L (4), L (9)]

D/10

mm

Horizontal Line

D

D/2

CS-1000T

Light Shield Room

(Ambient Luminance < 2 lux)

9D/10

W

W/10

W/2

1

4

2

5

3

6

X

Vertical Line

9W/10

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

7 8 9

Active Area

19 / 25

: Test Point

X=1 to 9

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Κ

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

8. PACKAGING

8.1 PACKING SPECIFICATIONS

(1) 9 LCD modules / 1 Box

(2) Box dimensions: 525(L) X 300 (W) X 360 (H) mm

(3) Weight: 19.79 Kg (9 modules per box)

(4) Desiccant ( Drier ) : Weight 30g / 1 piece, Cobalt chloride free.

8.2 PACKING METHOD

(1) Carton Packing should have no failure in the following reliability test items.

Test Item Test Conditions Note

ISTA STANDARD Random, Frequency Range: 1 – 200 Hz

Vibration

Dropping Test 1 Corner, 3 Edge, 6 Face, ISTA STANDARD Non Operation

Top & Bottom: 30 minutes (+Z), 10 min (-Z), Right & Left: 10 minutes (X) Back & Forth 10 minutes (Y)

Non Operation

Figure. 8-1 Packing method

20 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Doc No.:

Issued Date: Aug. 12, 2008

Model No.: M185B1-L03

Preliminary

For ocean shipping

Sea / Land Transportation (40ft HQ Container)

PP Belt

Carton label

Corner Protector (50*50*1000mm)

Film

PE Sheet

Corner Protector

(50*50*1000mm)

Pallet (1150*1150*143mm)

Sea / Land Transportation (40ft Container)

PP Belt

Carton label

Corner Protector (50*50*625mm)

Corner Protector (50*50*1000mm)

Pallet (1150*1150*143mm)

Film

PE Sheet

Corner Protector (50*50*1000mm)

Figure. 8-2 Packing method

For air transport

Corner Protector (50*50*1000mm)

PE Sheet

Film

Air Transportation

PP Belt

Carton label

Corner Protector (50*50*1000mm)

Pallet (1150*1150*143mm)

Figure. 8-3 Packing method

21 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

,

y

www.panelook.com

Doc No.:

Issued Date: Aug. 12, 2008

Model No.: M185B1-L03

Preliminary

9. DEFINITION OF LABELS

9.1 CMO MODULE LABEL

The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.

(a) Model Name: M185B1-L03

(b) Revision: Rev. XX, for example: A0, A1… B1, B2… or C1, C2…etc.

(c) CMO barcode definition:

Serial ID: XX

-XX-X-XX-YMD-L-NNNN

Code Meaning Description

XX CMO internal use XX Revision Cover all the change

X CMO internal use -

XX CMO internal use -

YMD Year, month, day

Year: 2001=1, 2002=2, 2003=3, 2004=4… Month: 1~12=1, 2, 3, ~, 9, A, B, C

~

=

~

L Product line # Line 1=1, Line 2=2, Line 3=3, …

NNNN Serial number Manufacturing sequence of product

(d) Customer’s barcode definition:

Serial ID: CM

-18B13-X-X-X-XX-L-XX-L-YMD-NNNN

Code Meaning Description

CM Supplier code CMO=CM

18B13 Model number M185B1-L03 = 18B13

X Revision code Non ZBD: 1,~,9,0 / ZBD: A~Z

Source driver IC

X X Gate driver IC code

Century=1, CLL=2, Demos=3, Epson=4, Fujitsu=5, Himax=6, Hitachi=7, Hynix=8, LDI=9, Matsushita=A, NEC=B, Novatec=C, OKI=D, Philips=E, Renasas=F

Samsung=G, Sanyo=H, Sharp=I, TI=J, Topro=K, Toshiba=L

XX Cell location Tainan Taiwan=TN, Ningbo China=NP

L Cell line #

1,2,~,9,A,B,~,Y,Z

XX Module location Tainan Taiwan=TN, Ningbo China=NP

L Module line #

YMD Year, month, day

1,2,~,9,A,B,~,Y,Z

Year: 2001=1, 2002=2, 2003=3, 2004=4… Month: 1~12=1, 2, 3, ~, 9, A, B, C Da

: 1~31=1, 2, 3, ~, 9, A, B, C, ~, T, U, V

NNNN Serial number By LCD supplier

~

(e) UL Factory ID:

Region Factory ID

TWCMO GEMN

NBCMO LEOO

NBCME CANO

NHCMO CAPG

22 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

Global LCD Panel Exchange Center

Issued Date: Aug. 12, 2008

www.panelook.com

Doc No.:

Model No.: M185B1-L03

Preliminary

10. PRECAUTIONS

10.1 ASSEMBLY AND HANDLING PRECAUTIONS

(1) Do not apply rough force such as bending or twisting to the module during assembly.

(2) To assemble or install module into user’s system can be only in clean working areas. The dust and oil

may cause electrical short or worsen the polarizer.

(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will

be damaged.

(4) Always follow the correct power sequence when LCD module is connecting and operating. This can

prevent damage to the CMOS LSI chips during latch-up.

(5) Do not pull the I/F connector in or out while the module is operating.

(6) Do not disassemble the module.

(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and

easily scratched.

(8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage

LCD module when it is operating.

(9) High temperature or humidity may reduce the performance of module. Please store LCD module within

the specified storage conditions.

(10) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the

response time will become slowly, and the starting voltage of CCFL will be higher than room

temperature.

10.2 SAFETY PRECAUTIONS

(1) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while

assembling with inverter. Do not disassemble the module or insert anything into the Backlight unit.

(2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In

case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.

(3) After the module’s end of life, it is not harmful in case of normal operation and storage.

10.3 OTHER

When fixed patterns are displayed for a long time, remnant image is likely to occur.

23 / 25

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

Version 1.0

www.panelook.com

CMO M185B1-L03 Specification

Specifications and Main Features

Frequently Asked Questions

User Manual