Page 1
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 2
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
- CONTENTS -
REVISION HISTORY ------------------------------------------------------- 3
1. GENERAL DESCRIPTION ------------------------------------------------------- 4
1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
2. ABSOLUTE MAXIMUM RATINGS ------------------------------------------------------- 4
3. SUGGESTIVEDRIVING CONDITION ------------------------------------------------------- 5
4. PANEL PIN DEFINE ------------------------------------------------------- 6
5. OPTICAL CHARACTERISTICS ------------------------------------------------------- 7
5.1 TEST CONDITIONS
5.2 OPTICAL SPECIFICATIONS
6. PACKAGING ------------------------------------------------------- 11
6.1 PACKING SPECIFICATIONS
6.2 PACKING METHOD
7. DEFINITION OF LABELS ------------------------------------------------------- 12
8. PRECAUTIONS ------------------------------------------------------- 13
8.1 ASSEMBLY AND HANDLING PRECAUTIONS
8.2 SAFETY PRECAUTIONS
2/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 3
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
REVISION HISTORY
Version Date Section Description
Ver 2.0
Nov., 24 ’04
- Approval Specification was first issued.
3/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 4
Global LCD Panel Exchange Center
1. GENERAL DESCRIPTION
1.1 OVERVIEW
The M150X4-C01 is a 15-inch LCD cell with thin film transistors as active elements and contains
1024x768 pixels. Each pixel is divided into red, green and blue dot, which are arranged in vertical stripe.
The cell is normally white mode, and can be applied to the transmission type display. Backlight unit (BLU)
and circuit board for the cell are not built in.
1.2 FEATURES
1. Wide viewing angle
2. High contrast ratio
3. Fast response time
4. XGA (1024 x 768 pixels) resolution
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
1.3 APPLICATION
1. LCD Monitor
2. LCD TV
1.4 GENERAL SPECIFICATI0NS
Item Specification Unit
Max Panel Dimension (TFT) 312.8 × 235.8 mm
Glass thickness (TFT/ CF) 0.6 / 0.6 mm
Active Area 304.128(H) × 228.096(V) (15.0” diagonal) mm
Driver Element a-si TFT active matrix Pixel Number 1024 × R.G.B. × 768 pixel
Pixel Pitch 0.297(H) × 0.297(W) mm
Pixel Arrangement RGB vertical stripe Transmissive Mode Normally white Surface Treatment Hard coating (3H), AG (Haze 25%) Polarizer Type Wide View -
Polarizer Dimension
Polarizer Thickness
TFT 307.2 × 231 mm
CF 309.8 × 232.8 mm
TFT 0.405 mm
CF 0.25 mm
2. ABSOLUTE MAXIMUM RATINGS
1. Storage Condition : With shipping package.
2. Storage temperature range : 25±5 к.
3. Storage humidity range : 50±10% RH.
4. Shelf life : 30 days.
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4/13
www.panelook.com
Page 5
Global LCD Panel Exchange Center
3. Suggestive Driving Condition
Item Min. Typ. Max. Unit
VG
Driving Voltage
B : Black pattern
W : White pattern
Gamma Voltage : Gam1 > Gam2 > Gam3 > … > Gam10
VD
V
GЦ-D offset
Charging time - 14.4 - us
On 17.4 17.75 18.1 V
Off -7.1 -6.91 -6.7 V
Gam1 9.2 9.4 9.6 V
B
Gam10 0.01 0.21 0.41 V
Gam5 5.82 6.02 6.22 V
W
Gam6 3.81 4.01 4.21 V
Center - 4.14 - V
COM
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
- 2.4 - us
GЦ: gate pulse falling edge
V
D
V
Com
DRIVING TIMING DIAGRAM
VG
5/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 6
Global LCD Panel Exchange Center
4. Panel PIN Define
Pin
No.
TAB1 TAB2~7 TAB8
1~2 NC NC NC
3 OE3 NC NC
4 OE2 NC NC
5 OE1 NC NC
6 VDD NC NC
7 VGL NC NC
8 VEE NC NC
9 VGH NC NC
10 DIO NC NC
11 CKV NC NC
12 XAO NC NC
13 GND NC NC
14 VCOM VCOM VCOM
15 floating is recommended floating is recommended floating is recommended
16 out1 out1 out1
17 out2 out2 out2
: : : :
398 out383 out383 out383
399 out384 out384 out384
400 floating is recommended floating is recommended floating is recommended
401 NC NC floating is recommended
402 NC NC floating is recommended
403 VCOM VCOM VCOM
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
Data driver Pin Define
Note: Recommended Gate IC for the cell is HiMAX’s HX8608APD400, 264Ch, or equivalent
6/13
.
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 7
Global LCD Panel Exchange Center
5. OPTICAL CHARACTERISTICS
5.1 TEST CONDITIONS
Item Symbol Value Unit
Ambient Temperature Ta
Ambient Humidity Ha
Gamma voltage Refer to item 3. Driving Condition V
Vcom most suitable Vcom V
5.2 OPTICAL SPECIFICATIONS
ITEM Symbol Condition MIN. TYP. MAX. UNIT NOTE
Contrast Ratio CR x=y=0ш 200 350 - % 4,1
(Black/White)
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
o
25r2
50r10
Tr x=y=0ш - 6 10 ms Response Time
Tf x=y=0ш - 17 25 ms
C
%RH
5,1
Center point Transmittance T% x=y=0ш 11.5 13 - % 7,1
Transmittance uniformity
(13pts)
Viewing
Angle
Color
Coordinat
es at
center
point
(y=0ш)
Vertical y
(x=0ш)
Red
Green
Blue
White
Red
Green
Blue
White
ӬT%
Right 50 60 - Deg Horizontal x
Left 50 60 - Deg
Up 30 40 - Deg
Down
Rcx x=y=0ш 0.635 Rcy x=y=0ш 0.347 Gcx x=y=0ш 0.296 Gcy x=y=0ш 0.581 Bcx x=y=0ш 0.129 -
Bcy x=y=0ш 0.156 Wcx x=y=0ш 0.317 Wcy x=y=0ш
Rx x=y=0ш 0.632 Ry x=y=0ш 0.347 Gx x=y=0ш 0.302 Gy x=y=0ш 0.580 Bx x=y=0ш 0.142 -
By x=y=0ш 0.094 Wx x=y=0ш 0.310 Wy x=y=0ш
x=y=0ш - - 1.4 - 6,1
CRɪ10
50 60 - Deg
Typ
-0.03
0.371
Typ
-0.03
0.322
Typ
+0.03
-
Typ
+0.03
-
2,3,1
2,0
2,1
Note (0)
Light source is the standard light source “C” which is defined by CIE and driving voltages are based on
suitable gamma voltages. The calculating method is as following:
1. Measure LCM module’s and BLU’s spectrums. White is without signal input and R, G, B are with
signal input. BLU is supplied by CMO.
2. Calculate cell’s spectrum.
3. Calculate cell’s chromaticity by using the spectrum of standard light source “C”
7/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 8
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
Note (1)
Light source is the BLU which is supplied by CMO and driving voltages are based on suitable gamma
voltages. White is without signal input and R, G, B are with signal input. Spec is judged by CMO’s golden sample.
Note (2) : Measurement setup
The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting backlight
for 20 minutes in a windless room.
LCD Module
LCD Panel
Center of the Screen
Photometer
(TOPCON BM-5A or CS-1000T)
Field of View = 2º
500 mm
Light Shield Room
(Ambient Luminance < 2 lux)
8/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 9
Global LCD Panel Exchange Center
Note (3) : Definition of viewing angle (x ,y):
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
Note (4) : Definition of Contrast Ratio (CR):Ratio of gray max (Gmax), gray min (Gmin), at the center point of panel.
BLU is supplied by CMO
CR =
Note (5) : Definition of Response Time (T
100%
90%
Optical
Response
Luminance with all pixel white (Gmax)
Luminance with all pixel Black (Gmin)
R, TF):
10%
0%
T
R T
Time
F
9/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 10
Global LCD Panel Exchange Center
Note (6) : Definition of Transmittance Variation (GT%):
Measure the transmittance at 13 points
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
T% =
Maximum [T%(1), T%(2), … T%(13)]
Minimum [T%(1), T%(2), … T%(13)]
D/10
W
W/10
W/4
W/2
6
9
Vertical Line
3W/4
9W/10
11 12 13
Note (7) : Definition of Transmittance(T%):
D
D/4 D/2 3D/4
7
2 3
1
4
Active Area
5
9D/10
8
10
X
: Test Point
X=1 to 13
Module is without signal input.
BLU is supplied by CMO
Transmittance =
Luminance of LCD module
Luminance of backlight
Ϡ 100%
10/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 11
Global LCD Panel Exchange Center
6. PACKAGING
6.1 PACKING SPECIFICATIONS
1. 20 LCD Panel / 1 Box
2. Box dimensions : 375(L) X 322(W) X 435(H) mm
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
3. Weight : approximately 7.55Kg (20 panel per box)
6.2 PACKING METHOD
LCD Monitor Panel
PP Box(Bottom)
Carton Label
PP Box(Cover)
PP Belt
2pcs Dryer
Vacuum Bag
Box dimensions : 375(L) X 322(W) X 435(H) mm
Weight : approximately 7.55Kg (20 panel per box)
Tape
Carton
Carton Label
Figure. 6-1 Packing method
11/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 12
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
Figure. 6-2 Packing method
7. DEFINITION OF LABELS
1. Model name: M150X4-C01
2. Panel Type: version control
3. Quantity: 20pcs / PP box
4. Case ID: serial number.
5. Note : Notification, if necessary.
6. Barcode : Case ID in code 39 format
Figure. 7-1 Packing Label
12/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 13
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Nov.24 2004
Model No.: M150X4-C01
Approval
8. PRECAUTIONS
8.1 ASSEMBLY AND HANDLING PRECAUTIONS
1. Do not apply rough force such as bending or twisting to the cell during assembly.
2. To assemble or install cell into customer’s module can be only in clean working areas. The dust and
oil may cause electrical short or worsen the polarizer.
3. It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight
will be damaged.
4. Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
5. It is dangerous that moisture come into or contacted the LCD panel, because moisture may damage
TFT circuit.
6. High temperature or humidity may reduce the performance of cell. Please store LCD cell within the
specified storage conditions.
8.2 SAFETY PRECAUTIONS
1. If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
13/13
Version 2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...