CMO M150X3-L0A Specification

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

- CONTENTS -

REVISION HISTORY ------------------------------------------------------- 3

1. GENERAL DESCRIPTION

1.1 OVERVIEW

1.2 FEATURES

1.3 APPLICATION

1.4 GENERAL SPECIFICATIONS

1.5 MECHANICAL SPECIFICATIONS

------------------------------------------------------- 4

2. ABSOLUTE MAXIMUM RATINGS ------------------------------------------------------- 5

2.1 ABSOLUTE RATINGS OF ENVIRONMENT

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE

2.2.2 BACKLIGHT UNIT

3. ELECTRICAL CHARACTERISTICS ------------------------------------------------------- 7

3.1 TFT LCD MODULE

3.2 BACKLIGHT UNIT

4. BLOCK DIAGRAM ------------------------------------------------------- 10

4.1 TFT LCD MODULE

4.2 BACKLIGHT UNIT

5. INPUT TERMINAL PIN ASSIGNMENT ------------------------------------------------------- 11

5.1 TFT LCD MODULE

5.2 BACKLIGHT UNIT

5.3 COLOR DATA INPUT ASSIGNMENT

6. INTERFACE TIMING ------------------------------------------------------- 13

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

6.2 POWER ON/OFF SEQUENCE

7. OPTICAL CHARACTERISTICS ------------------------------------------------------- 16

7.1 TEST CONDITIONS

7.2 OPTICAL SPECIFICATIONS

8. PRECAUTIONS ------------------------------------------------------- 19

8.1 HANDLING PRECAUTIONS

8.2 STORAGE PRECAUTIONS

8.3 OPERATION PRECAUTIONS

2 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

REVISION HISTORY

Version Date

Ver 3.0 Apr.15’2003 All All

Page

(New)

Section Description

3 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

1. GENERAL DESCRIPTION

1.1 OVERVIEW

M150X3-L0A is a 15.0” TFT Liquid Crystal Display module with 4 CCFL Backlight units and 20 pins LVDS

interface. This module supports 1024 x 768 XGA mode and can display 16.2M. The optimum viewing angle

is at 6 o’clock direction. The inverter module for Backlight is not built in.

1.2 FEATURES

- XGA (1024 x 768 pixels) resolution

- DE (Data Enable) only mode

- LVDS Interface with 1pixel/clock

1.3 APPLICATION

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

- Desktop monitors

1.4 GENERAL SPECIFICATI0NS

Item Specification Unit Note Active Area 304.1(H) x 228.1(V) (15.0” diagonal) mm Bezel Opening Area 308.2(H) x 232.1(V) mm Driver Element a-Si TFT active matrix - Pixel Number 1024 x R.G.B. x 768 pixel Pixel Pitch 0.297(H) x 0.297(W) mm Pixel Arrangement RGB vertical stripe - Display Colors 16,194,277 color Transmissive Mode Normally white - -

1.5 MECHANICAL SPECIFICATIONS

Item Min. Typ. Max. Unit Note

Horizontal(H) - 331.6 - mm

Module Size

Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.

Vertical(V) - 254.76 - mm Depth(D) - 13.0 13.5 mm

Weight - - 1,350 g -

(1)

4 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT

Item Symbol

Storage Temperature TST -20 +60 ºC (1) Operating Ambient Temperature TOP 0 +50 ºC (1), (2) Storage Humidity HST 5 85 % Operation Humidity HOP 20 85 % Shock (Non-Operating) S Vibration (Non-Operating) V

Note (1) Temperature and relative humidity range is shown in the figure below.

(a) 85 %RH Max. (Ta Љ 40 ºC).

(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).

(c) No condensation of water.

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Value

Min. Max.

- 50 G (3), (5)

NOP

- 2 G (4), (5)

NOP

Unit Note

Relative Humidity (%RH)

100

85

80

60

Operating Range

40

20

Storage Range

5

Temperature (ºC)

8060-20 400 20-40

Note (2) The temperature of panel surface should be 0 ºC Min. and 60 ºC Max.

Note (3) 6ms, 1 time each ±X,±Y and ±Z directions

Note (4) 10 ~ 500 Hz, 1 cycle/20min. 1.5mm max, 1 hour each X, Y and Z directions

Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough

so that the module would not be twisted or bent by the fixture.

5 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE

Item Symbol

Power Supply Voltage VDD -0.3 4.0 V

2.2.2 BACKLIGHT UNIT

Item Symbol

Lamp Voltage VL 603 737 V Lamp Current IL 2.0 6.5 mA Lamp Frequency FL 30 80 KHz

Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation

should be restricted to the conditions described under Normal Operating Conditions.

www.panelook.com

Value

Min. Max.

Value

Min. Max.

Unit Note

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

(1), (2), IL = 5.5 mA

RMS

(1), (2)

Note (2) Specified values are for lamp (Refer to Section 3.2 for further information).

6 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

3. ELECTRICAL CHARACTERISTICS

3.1 TFT LCD MODULE

Parameter Symbol

Power Supply Voltage VDD 3.0 3.3 3.6 V Ripple Voltage VRP - - 100 mVp-p Rush Current I

White - 350 380 mA (3)a

Power Supply Current

LVDS Receiver Threshold Terminating Resistor RT - 100 - Ohm -

Note (1) The module should be always operated within above ranges.

Note (2) Measurement Conditions:

Black - 530 570 mA (3)b Vertical Stripe “H” Level VIH - - 100 mV - Differential Input Voltage for “L” Level V

www.panelook.com

Min. Typ. Max.

- - 1.5 A (2)

RUSH

lcc

- 450 480 mA (3)c

-100 - - mV -

IL

Value

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Unit Note

(High to Low)

(Control Signal)

SW

+12V

+3.3V

R1

47K

R2

1K

47K

VR1

C1

1uF

Q1 2SK1475

C2

0.01uF

Q2

2SK1470

FUSE

C3

1uF

VDD

(LCD Module Input)

+3.3V

0.9 V

DD

0.1 V

DD

GND

470Ӵs

7 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (3) The specified power supply current is under the conditions at VDD =3.3V, Ta = 25 ± 2 ºC, DC

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Current and f

a. White Pattern

c. Vertical Stripe Pattern

= 60 Hz, whereas a power dissipation check pattern below is displayed.

v

Active Area

b. Black Pattern

Active Area

R

G

R

B

G

R

B

G

B

R

G

B

R

Active Area

R R

G

B

G

B

3.2 BACKLIGHT UNIT Ta = 25 ± 2 ºC

Parameter Symbol

Lamp Input Voltage VL 603 670 737 V Lamp Current IL 2.0 5.5 6.5 mA

Lamp Turn On Voltage V

Operating Frequency FL 30 45 80 KHz (3) Lamp Life Time LBL 40,000 50,000 - Hrs (5) Power Consumption PL - 14740 - mW (4), IL = 5.5 mA

Note (1) Lamp current is measured by utilizing a high frequency current meter as shown below:

S

HV (Pink/ Blue)

Min. Typ. Max.

- - 1350 (25oC) V

- - 1510 (0

LCD

Module

LV (White/ Black)

Value

1

2

Current Meter

Unit Note

o

C) V

I

RMS

(1)

RMS

(2)

RMS

(2)

RMS

= 5.5mA

L

Inverter

A

Note (2) The voltage shown above should be applied to the lamp for more than 1 second after startup.

Otherwise the lamp may not be turned on.

8 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (3) The lamp frequency may generate interference with horizontal synchronous frequency from the

display, and this may cause line flow on the display. In order to avoid interference, the lamp

frequency should be detached from the horizontal synchronous frequency and its harmonics as far

as possible.

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Note (4) P

L

= I

LVL

Note (5) The lifetime of lamp is defined as the time when it continues to operate under the conditions at Ta

= 25 2

o

C and IL =6.5mA

until one of the following events occurs:

RMS

(a) When the brightness becomes Љ 50% of its original value.

(b) When the effective ignition length becomes Љ 80% of its original value. (Effective ignition

length is defined as an area that the brightness is less than 70% compared to the center point.)

Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the

inverter must have specifications for the modularized lamp. The performance of the Backlight,

such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for

the lamp. All the parameters of an inverter should be carefully designed to avoid generating too

much current leakage from high voltage output of the inverter. When designing or ordering the

inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the

inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module

should be operated in the same manners when it is installed in your instrument.

9 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

)

V

(

)

4. BLOCK DIAGRAM

4.1 TFT LCD MODULE

LVD S

IINPUT

(Hirose DF14H-20P-1.25H)

INPUT CONNECTOR

LVDS

INPUT

www.panelook.com

TIMING

CONTROLLER

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

SCAN DRIVER IC

TFT LCD PANEL

(1024x3x768)

DC

POWER

SUPPLY

LAMP CONNECTOR

4.2 BACKLIGHT UNIT

REFERENCE VOLTAGE

(JST BHSR-02VS-1)

DC/DC CONVERTER &

GENERATOR

DATA DRIVER IC

BACKLIGHT UNIT

1 HV (Pink 2 LV (White

1 HV (Blue

2 L

Black

1 HV (Pink

2 LV (White

1 HV (Blue

2 LV (Black

10 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

5. INPUT TERMINAL PIN ASSIGNMENT

5.1 TFT LCD MODULE

Pin No. Symbol Function Polarity Note 1 VDD Power Supply +3.3V(typical) 2 VDD Power Supply +3.3V(typical) 3 GND Ground 4 GND Ground 5 RX0- LVDS Differential Data Input Negative 6 RX0+ LVDS Differential Data Input Positive 7 GND Ground 8 RX1- LVDS Differential Data Input Negative 9 RX1+ LVDS Differential Data Input Positive 10 GND Ground 11 RX2- LVDS Differential Data Input Negative 12 RX2+ LVDS Differential Data Input Positive 13 GND Ground 14 RXCLK- LVDS Differential Data Input Negative 15 RXCLK+ LVDS Differential Data Input Positive 16 GND Ground 17 RX3- LVDS Differential Data Input Negative

18 RX3+ LVDS Differential Data Input Positive 19 GND GND 20 NC Reserved

(1)Connector Part No.: [Hirose] DF14H-20P-1.25H

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

(2)Matching socket Part No.: [Hirose] DF14-20S-1.25C

5.2 BACKLIGHT UNIT

Pin Symbol Description Color

1 HV1 High Voltage Pink/ Blue 2 LV Ground White/ Black

Note (1) Connector Part No.: BHSR-02VS-1 (JST) or equivalent

Note (2) Matching Connector Part No.: SM02B-BHSS-1-TB (JST) or equivalent

11 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

5.3 COLOR DATA INPUT ASSIGNMENT

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for

the color. The higher the binary input the brighter the color. The table below provides the assignment of

color versus data input.

Color

R7 R6 R5 R4 R3 R2 R1 R0 R7 R6 G5 G4 G3 G2 G1 G0 R7 R6 B5 B4 B3 B2 B1 B0

Basic Colors

Gray Scale Of Red

Black Red Green Blue Cyan Magenta Yellow White Red(0) / Dark Red(1) Red(2)

:

: Red(252) Red(252) Red(252)

0

1

0

1

0

:

1

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Data Signal

Red Green Blue

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

:

1

0

1

0

1

0

1

0

Green(0)/Dark Green(1)

Gray Scale Of Green

Gray Scale Of Blue

Note (1) 0: Low Level Voltage, 1: High Level Voltage

Green(2)

:

: Green(252) Green(252) Green(252) Blue(0) / Dark Blue(1) Blue(2)

:

: Blue(252) Blue(252) Blue(252)

0

:

0

:

0

1

0

1

0

:

1

0

1

0

1

0

1

0

1

0

1

0

:

0

1

0

1

0

1

0

1

12 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

6. INTERFACE TIMING

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

The input signal timing specifications are shown as the following table and timing diagram.

Signal Parameter Symbol Min Typ Max Unit Remarks

DCLK

DATA

DE

Vertical

Horizontal

Pixel clock Frequency Fck - 65 80 MHz Pixel clock period Tck 12.5 15 20 ns

Duty ratio (%Tch) - 45 50 55 % Tch/Tck

High time Tckh 5 - - ns Low time Tckl 5 - - ns Setup time Tsd 4 - - ns Hold time Thd 4 - - ns Setup time Tsde 4 - - ns Hold time Thde 4 - - ns Vertical Frequency Fv - 60 75 Hz Vertical display active period Tvda 768 768 768 Thp Vertical display blank period Tvdb 1 38 - Thp Vertical period Tvp 769 806 - Thp Horizontal display active

period Horizontal display blank period Thdb 76 320 776 Tck Horizontal period Thp 1100 1344 1800 Tck

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Thda 1024 1024 1024 Tck

Note (1) Because this module is operated by DE only mode, Hsync and Vsync input signals should be set

to low logic level or ground. Otherwise, this module would operate abnormally.

13 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

T

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

INPUT SIGNAL TIMING DIAGRAM

Tvp

DE

DCLK

DATA

DE

768

Thdb

Tvdb

Tvda

1

2

768

Thp

Thda

Valid display data (1024 Tck)

Invalid Valid

DCLK

DATA

DE

Tckh

ckl

Tch

Tsde

Tck

0.7VDD

0.3VDD

ThdTsd

0.7VDD

0.3VDD

Thde

0.7VDD

14 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

C

TxCLK OUT

Rx

K IN

T/7

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

TIMING DIAGRAM of LVDS

T

Rx IN3

Rx IN2

Rx IN1

Rx IN0

RxOUT23

RxOUT17

RxOUT16 RxOUT11 RxOUT10

RxOUT5

RxOUT27

RESERVED B07 B06 G07 G06 R07 R06

RxOUT26

RxOUT25 RxOUT24 RxOUT22

RxOUT21

RxOUT20

RxOUT19

DE GND GND B05 B04 B03 B02

RxOUT18

RxOUT15 RxOUT14 RxOUT13

RxOUT12

RxOUT9

RxOUT8

B01 B00 G05 G04 G03 G02 G01

RxOUT7 RxOUT6

RxOUT4

RxOUT3 RxOUT2

RxOUT1

RxOUT0

G00 R05 R04 R03 R02 R01 R00

15 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

6.2 POWER ON/OFF SEQUENCE

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Power Supply

for LCD, V

DD

- Interface Signal

(LVDS Signal of Transmitter), V

I

- Power for Lamp

Timing Specifications:

0 < t1 Љ 10 msec

0 < t2 Љ 50 msec

0V

Power On

90%

10%

Restart

t4

10%

Power Off

90%

t1

t3t2

Valid Data

t6t5

ONOFF OFF

0 < t3 Љ 50 msec

t4 Њ 400 msec

t5 Њ 100 msec

t6 Њ 100 msec

Note (1) Please avoid floating state of interface signal at invalid period.

Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD V

to 0 V.

DD

Note (3) The Backlight inverter power must be turned on after the power supply for the logic and the

interface signal is valid. The Backlight inverter power must be turned off before the power supply

for the logic and the interface signal is invalid.

16 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

7. OPTICAL CHARACTERISTICS

7.1 TEST CONDITIONS

Item Symbol Value Unit Ambient Temperature Ta Ambient Humidity Ha Supply Voltage Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS" Inverter Current IL 5.5 mA

The measurement methods of optical characteristics are shown in Section 7.2. The following items

should be measured under the test conditions described in Section 7.1 and stable environment shown in

Note (4).

7.2 OPTICAL SPECIFICATIONS

Item Symbol Condition Min. Typ. Max. Unit Note

Contrast Ratio CR 250

Response Time

Center Luminance of White L 200 250 - cd/m Luminance Uniformity

Red

Color Chromaticity

Viewing Angle

Green

Blue

White

Horizontal

Vertical

Horizontal

Vertical

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

o

25r2

50r10

V

DD

TR -

-

T

F

GW

Rx 0.607 0.637 0.667 Ry 0.323 0.353 0.383 -

=0q, TY =0q

T

x

Viewing Normal Angle

3.3 V

300

7

23

- - (2), (4) 22 ms 38 ms

75 - - - (6)

Gx 0.272 0.302 0.332 Gy 0.558 0.588 0.618 Bx 0.111 0.141 0.171 -

By 0.064 0.094 0.124 Wx 0.274 0.304 0.334 Wy

Tx+

T

x

TY+

T

Y

Tx+

T

x

TY+

T

Y

CRt10

-

CRt5

-

0.295 0.325 0.355 50 60 50 60 30 40 50 60 65 - 65 - 30 - 50 - -

C

%RH

2

Deg.

(3)

(4)

(1), (4)

17 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (1) Definition of Viewing Angle (Tx, Ty):

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Normal

Tx = Ty = 0º

Ty- Ty

TX- = 90º

6 o’clock

T

y- = 90º

x-

y-

Note (2) Definition of Contrast Ratio (CR):

The contrast ratio can be calculated by the following expression.

Contrast Ratio (CR) = L255 / L0

L255: Luminance of gray level 255

L 0: Luminance of gray level 0

CR = CR (5)

Tx-

Tx

y+

12 o’clock direction

T

y+ = 90º

x+

TX+ = 90º

CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (5).

Note (3) Definition of Response Time (T

Gray Level 255

100%

90%

Optical

Response

10%

0%

R

T

R

, TF):

Gray Level 0

Gray Level 255

Time

T

F

18 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (4) Measurement Setup:

The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt

temperature change during measuring. In order to stabilize the luminance, the measurement

should be executed after lighting Backlight for 20 minutes in a windless room.

LCD Module

LCD Panel

Center of the Screen

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Photometer

(TOPCON BM-5A)

Field of View = 2º

500 mm

Note (5) Definition of luminance measured points:

3D/20

W

3W/20

W/2

1

4

Vertical Line

Light Shield Room

(Ambient Luminance < 2 lux)

D

D/2

23

5

3D/20

6

: test point

X

X=1 to 9

3W/20

7

8 9

Active area

Horizontal Line Number [Pixel]

Note (6) Definition of luminance uniformity GW (9 points, gray level 255):

GW = (Minimum [L (1), L (2), L (3), L (4), L (5), L(6)], L(7), L(8), L(9) ) / Maximum [L (1), L (2), L (3), L (4), L

(5), L(6), L(7), L(8), L(9)]) %

19 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

8. PRECAUTIONS

8.1 HANDLING PRECAUTIONS

(1) The module should be assembled into the system firmly by using every mounting hole. Be careful not

to twist or bend the module.

(2) While assembling or installing modules, it can only be in the clean area. The dust and oil may cause

electrical short or damage the polarizer.

(3) Use fingerstalls or soft gloves in order to keep display clean during the incoming inspection and

assembly process.

(4) Do not press or scratch the surface harder than a HB pencil lead on the panel because the polarizer is

very soft and easily scratched.

(5) If the surface of the polarizer is dirty, please clean it by some absorbent cotton or soft cloth. Do not use

Ketone type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It might

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

permanently damage the polarizer due to chemical reaction.

(6) Wipe off water droplets or oil immediately. Staining and discoloration may occur if they left on panel for

a long time.

(7) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In

case of contacting with hands, legs or clothes, it must be washed away thoroughly with soap.

(8) Protect the module from static electricity, it may cause damage to the C-MOS Gate Array IC.

(9) Do not disassemble the module.

(10) Do not pull or fold the lamp wire.

(11) Pins of I/F connector should not be touched directly with bare hands.

8.2 STORAGE PRECAUTIONS

(1) High temperature or humidity may reduce the performance of module. Please store LCD module within

the specified storage conditions.

(2) It is dangerous that moisture come into or contacted the LCD module, because the moisture may

damage LCD module when it is operating.

(3) It may reduce the display quality if the ambient temperature is lower than 10 ºC. For example, the

response time will become slowly, and the starting voltage of lamp will be higher than the room

temperature.

8.3 OPERATION PRECAUTIONS

(1) Do not pull the I/F connector in or out while the module is operating.

(2) Always follow the correct power on/off sequence when LCD module is connecting and operating. This

can prevent the CMOS LSI chips from damage during latch-up.

(3) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while

assembling with inverter. Do not disassemble the module or insert anything into the Backlight unit.

20 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

9. PACKAGING

9.1 PACKING SPECIFICATIONS

(1) 5 LCD modules / 1 Box

(2) Box dimensions : 353(L) X 268(W) X 462(H) mm

(3) Weight : approximately 8.5Kg ( 5 modules per box)

9.2 PACKING Method

Figures 9-1and 9-2 are the packing method.

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Figure. 9-1 Packing method

21 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

Figure. 9-2 Packing method

22 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

10. INCOMING INSPECTION DAY

The Supplier should be acquainted the inspection results (acceptance or rejection) by Customer, and the results

are in accordance with the incoming inspection standard within 30 days after the date of the bills of lading.

Should Customer fail to so notify the Supplier within the said 30 days period. The Customer’s right to reject the

LCMS shall then lapse, and the said LCMS shall be deemed to have been accepted by the customer.

23 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

11. DEFINITION OF LABELS

11.1 CMO MODULE LABEL

The barcode nameplate is pasted on each module as illustration, and its definitions are as following

explanation.

www.panelook.com

Issued Date: Apr.15, ’2003

Model No.: M150X3-L0A

Approval

CHI MEI

OPTOELECTRONICS

01A

(a) Model Name: M150X3 –L01

(b) Revision: Rev. XX, for example: C1, C2 …etc.

(c) Serial ID: X X

X X X X X Y M D L N N N N

M150X3 –L0A Rev. XX

X X X X X X X Y M D L N N N N

CP175242-01

MADE IN TAIWAN

E207943

MADE IN TAIWAN

Serial No.

Product Line

Year, Month, Date

CMO Internal Use

Color Filter

Serial ID includes the information as below:

(a) Manufactured Date: Year: 1~9, for 2000~2009

Month: 1~9, A~C, for Jan. ~ Dec.

Day: 1~9, A~Y, for 1

(b) Revision Code: cover all the change

(c) Color Filter: 0 ->CMO, 2 -> Toppan

(d) Serial No.: Manufacturing sequence of product

(e) Product Line: 1 -> Line1, 2 -> Line 2, …etc.

Revision

CMO Internal Use

st

to 31st, exclude I and O

24 / 24

Version3.0

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

E207943

MADE IN TAIWAN

Rev. C1

M150X3 -L01

CAUTION

HIGH VOLTAGE

RISK OF ELECTRIC SHOCK.

DISCONNECT THE ELECTRIC

POWER BEFORE SERVICING.

COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CONTAINS A SMALL AMOUNT OF

MERCURY PLEASE FOLLOW LOCAL ORDINANCES OR REGULATIONS FOR DISPOSAL.

CMO M150X3-L0A Specification

Specifications and Main Features

Frequently Asked Questions

User Manual