CMO M150X3-L01 Specification

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

REVISION HISTORY

1. GENERAL DESCRIPTION

1.1 OVERVIEW

1.2 FEATURES

1.3 APPLICATION

1.4 GENERAL SPECIFICATIONS

1.5 MECHANICAL SPECIFICATIONS

2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE

2.2.2 BACKLIGHT UNIT

3. ELECTRICAL CHARACTERISTICS

3.1 TFT LCD MODULE

3.2 BACKLIGHT UNIT

4. BLOCK DIAGRAM

4.1 TFT LCD MODULE

4.2 BACKLIGHT UNIT

5. INPUT TERMINAL PIN ASSIGNMENT

5.1 TFT LCD MODULE

5.2 BACKLIGHT UNIT

5.3 COLOR DATA INPUT ASSIGNMENT

6. INTERFACE TIMING

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

6.2 POWER ON/OFF SEQUENCE

7. OPTICAL CHARACTERISTICS

7.1 TEST CONDITIONS

7.2 OPTICAL SPECIFICATIONS

8. PRECAUTIONS

8.1 HANDLING PRECAUTIONS

8.2 STORAGE PRECAUTIONS

8.3 OPERATION PRECAUTIONS

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

- CONTENTS -

------------------------------------------------------- 3

------------------------------------------------------- 4

------------------------------------------------------- 5

------------------------------------------------------- 7

------------------------------------------------------- 10

------------------------------------------------------- 11

------------------------------------------------------- 13

------------------------------------------------------- 16

------------------------------------------------------- 19

2 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Version Date

Ver 0.0

Ver 2.0

April.13’2001

July. 03’2001

Page

(New)

All

6

7

8

9

10

11

12

13

14

16

17

REVISION HISTORY

Section Description

Preliminary Specification was first issued.

All

2.2.1

3.1

3.2

4.1

5.1

5.3

6.1

6.2

7.2

Update Vcc(Symbol.)/Vss-0.3(Min.)àVdd(Symbol.)/-0.3(Min.)

Delete:Ripple

Update Irush:TBD(Max.)à1.5(Max.).

Update White Icc:TBD(Typ.)à350(Typ.)

Update Black Icc:TBD(Typ.)à530(Typ.)

Update Vertical Stripe Icc:TBD(Typ.)à450(Typ.)

Update “H” Level Vih:2.64(Min.)/Vcc(Max.)àDelete(Min.)/100(Max.)

Update:Note(2)

Update Vl:

640(Min.)/720(Typ.)/800(Max.)à603(Min.)/670(Typ.)/737(Max.)

Update Vs:

1150(25’C)(Max.)/1500(0’C)(Max.)à1350(25’C)(Max.)/1510(0’C)(Max.)

Update Lbl:50000(Min.)/40000(Min.)

Add.Lbl:50000(Typ.)

Update Pl:9360(Typ.)à14740(Typ.)

Update Note(5):7.0mAà6.5mA

Add:LVDS IINPUT

Add:DC POWER SUPPLY

Update:LVDS INPUT TIMING CONTROLLERàTIMING CONTROLLER

Update 17:

NC(Symbol.)/NC(Function.)àRX3-(Symbol.)/LVDS Differential Data

Input(Function.)

Update 18:

NC(Symbol.)/NC(Function.)à RX3+(Symbol.)/LVDS Differential Data

Input(Function.)

Update 20:

TST(Symbol.)/Test(Function.)àNC(Symbol.)/Reserved(Function.)

Add 17.18:Negative/Positive(Polarity)

Update:6-bità8-bit.

Update Pixel clock period:20(Min.)/12.5(Max.)à12.5(Min.)/20(Max.)

Update:

(1)2.0Và0.7VDD

(2)1.5Và0.5VDD

(3)0.8Và0.3VDD

(4)--- à0.7VDD

(5)0.8Và

(6)2.0Và0.7VDD

Update Note(2):VccàVDD

Update Tr:10(Typ.)/20(Max.)à7(Typ.)/22(Max.)

Update Tf:20(Typ.)/30(Max.)à23(Typ.)/38(Max.)

Add Color Chromaticity: Min. and Max.

0.3VDD

3 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Version Date

Ver2.0

Ver3.0

Ver3.1

July. 03’2001

July. 06’2001

Jan. 18’2002

Page

(New)

17

5

18

Section Description

7.2

1.5

7.2

Update Color Chromaticity Typ.

Rx:0.623à0.637

Ry:0.357à0.353

Gx:0.284à0.302

Gy:0.594à0.588

Bx:0.143à0.141

By:0.091à0.094

Wx:0.298à0.310

Wy:0.322à0.330

Add Depth (D)à13.5(Max.)

Update Wx:0.280(Min.)/0.310(Typ.)/0.340(Max.)à

0.274(Min.)/0.304(Typ.)/0.334(Max.)

Update Wy:0.300(Min.)/0.330(Typ.)/0.360(Max.)à

0.295(Min.)/0.325(Typ.)/0.355(Max.)

Revise Inspection Spec Ver 1.0A à Ver 1.0B

4 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

1. GENERAL DESCRIPTION

1.1 OVERVIEW

M150X3-L01 is a 15.0” TFT Liquid Crystal Display module with 4 CCFL Backlight units and 20 pins LVDS

interface. This module supports 1024 x 768 XGA mode and can display 16.2M. The optimum viewing angle

is at 6 o’clock direction. The inverter module for Backlight is not built in.

1.2 FEATURES

- XGA (1024 x 768 pixels) resolution

- DE (Data Enable) only mode

- LVDS Interface with 1pixel/clock

1.3 APPLICATION

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

- Desktop monitors

1.4 GENERAL SPECIFICATI0NS

Item Specification Unit Note
Active Area 304.1(H) x 228.1(V) (15.0” diagonal) mm
Bezel Opening Area 308.2(H) x 232.1(V) mm
Driver Element a-Si TFT active matrix - ­Pixel Number 1024 x R.G.B. x 768 pixel ­Pixel Pitch 0.297(H) x 0.297(W) mm ­Pixel Arrangement RGB vertical stripe - ­Display Colors 16,194,277 color ­Transmissive Mode Normally white - -

1.5 MECHANICAL SPECIFICATIONS

Item Min. Typ. Max. Unit Note

Horizontal(H) - 331.6 - mm

Module Size

Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.

Vertical(V) - 254.76 - mm
Depth(D) - 13.0 13.5 mm

Weight - - 1,350 g -

(1)

(1)

5 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT

Item Symbol

Storage Temperature TST -20 +60 ºC (1)
Operating Ambient Temperature TOP 0 +50 ºC (1), (2)
Storage Humidity HST 5 85 % ­Operation Humidity HOP 20 85 % ­Shock (Non-Operating) S
Vibration (Non-Operating) V

Note (1) Temperature and relative humidity range is shown in the figure below.

(a) 85 %RH Max. (Ta  40 ºC).

(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).

(c) No condensation of water.

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Value

Min. Max.

- 50 G (3), (5)

NOP

- 2 G (4), (5)

NOP

Unit Note

Relative Humidity (%RH)

100

85

80

60

Operating Range

40

20

Storage Range

5

Temperature (ºC)

8060 -20 400 20-40

Note (2) The temperature of panel surface should be 0 ºC Min. and 60 ºC Max.

Note (3) 6ms, 1 time each ±X,±Y and ±Z directions

Note (4) 10 ~ 500 Hz, 1 cycle/20min. 1.5mm max, 1 hour each X, Y and Z directions

Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough

so that the module would not be twisted or bent by the fixture.

6 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE

Item Symbol

Power Supply Voltage VDD -0.3 4.0 V

2.2.2 BACKLIGHT UNIT

Item Symbol

Lamp Voltage VL 603 737 V
Lamp Current IL 2.0 6.5 mA
Lamp Frequency FL 30 80 KHz

Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation

should be restricted to the conditions described under Normal Operating Conditions.

www.panelook.com

Value

Min. Max.

Value

Min. Max.

Unit Note

Unit Note

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

(1), (2), IL = 5.5 mA

RMS

RMS

(1), (2)

Note (2) Specified values are for lamp (Refer to Section 3.2 for further information).

7 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

3. ELECTRICAL CHARACTERISTICS

3.1 TFT LCD MODULE

Parameter Symbol

Power Supply Voltage VDD 3.0 3.3 3.6 V ­Rush Current I

White - 350 - mA (3)a

Power Supply Current

LVDS Receiver Threshold
Terminating Resistor RT - 100 - Ohm -

Note (1) The module should be always operated within above ranges.

Note (2) Measurement Conditions:

Black - 530 - mA (3)b
Vertical Stripe
“H” Level VIH - - 100 mV - Differential Input Voltage for
“L” Level V

www.panelook.com

Min. Typ. Max.

- - 1.5 A (2)

RUSH

lcc

- 450 - mA (3)c

-100 - - mV -

IL

Value

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Unit Note

+3.3V

R1

47K

Q1 2SK1475

FUSE

C3

1uF

VDD

(LCD Module Input)

(High to Low)

(Control Signal)

SW

+12V

C1

1uF

VR1

R2

1K

47K

0.01uF

Q2

2SK1470

C2

+3.3V

0.9 V

DD

0.1 VDD

GND

470ϴs

8 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (3) The specified power supply current is under the conditions at VDD =3.3V, Ta = 25 ± 2 ºC, DC

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Current and f

a. White Pattern

c. Vertical Stripe Pattern

= 60 Hz, whereas a power dissipation check pattern below is displayed.

v

b. Black Pattern

Active Area

Active Area

R

R

B

R

B

G

G

G

B

B

B

R

R

R

G

G

G

B

B

B

R

R

Active Area

R R

G

B

G

B

3.2 BACKLIGHT UNIT Ta = 25 ± 2 ºC

Parameter Symbol

Lamp Input Voltage VL 603 670 737 V
Lamp Current IL 2.0 5.5 6.5 mA

Lamp Turn On Voltage VS

Operating Frequency FL 30 45 80 KHz (3)
Lamp Life Time LBL 40,000 50,000 - Hrs (5)
Power Consumption PL - 14740 - mW (4), IL = 5.5 mA

Note (1) Lamp current is measured by utilizing a high frequency current meter as shown below:

LCD

Module

HV (Pink/ Blue)

LV (White/ Black)

Min. Typ. Max.

- - 1350 (25

- - 1510 (0

Value

1

2

Current Meter

Unit Note

o

C) V

o

C) V

I

RMS

(1)

RMS

(2)

RMS

(2)

RMS

= 5.5mA

L

Inverter

A

Note (2) The voltage shown above should be applied to the lamp for more than 1 second after startup.

Otherwise the lamp may not be turned on.

9 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (3) The lamp frequency may generate interference with horizontal synchronous frequency from the

display, and this may cause line flow on the display. In order to avoid interference, the lamp

frequency should be detached from the horizontal synchronous frequency and its harmonics as far

as possible.

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Note (4) P

Note (5) The lifetime of lamp is defined as the time when it continues to operate under the conditions at Ta

Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the

= IL VL

L

= 25 2

(a) When the brightness becomes  50% of its original value.

(b) When the effective ignition length becomes  80% of its original value. (Effective ignition

inverter must have specifications for the modularized lamp. The performance of the Backlight,

such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for

the lamp. All the parameters of an inverter should be carefully designed to avoid generating too

much current leakage from high voltage output of the inverter. When designing or ordering the

inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the

inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module

should be operated in the same manners when it is installed in your instrument.

o

C and IL =6.5mA

length is defined as an area that the brightness is less than 70% compared to the center point.)

until one of the following events occurs:

RMS

10 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

)

)

)

)

)

)

)

)

4. BLOCK DIAGRAM

4.1 TFT LCD MODULE

LVD S

IINPUT

(Hirose DF14H-20P-1.25H)

INPUT CONNECTOR

LVDS

INPUT

DC

POWER

SUPPLY

www.panelook.com

TIMING

CONTROLLER

DC/DC CONVERTER &

REFERENCE VOLTAGE

GENERATOR

Issued Date:Jan.18’2002

Model No.: M150X3-L01

SCAN DRIVER IC

TFT LCD PANEL

(1024x3x768)

DATA DRIVER IC

Approval

LAMP CONNECTOR

4.2 BACKLIGHT UNIT

(JST BHSR-02VS-1)

BACKLIGHT UNIT

1 HV (Pink
2 LV (White

1 HV (Blue

2 LV (Black

1 HV (Pink

2 LV (White

1 HV (Blue

2 LV (Black

11 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

5. INPUT TERMINAL PIN ASSIGNMENT

5.1 TFT LCD MODULE

Pin No. Symbol Function Polarity Note
1 VDD Power Supply +3.3V(typical)
2 VDD Power Supply +3.3V(typical)
3 GND Ground
4 GND Ground
5 RX0- LVDS Differential Data Input Negative
6 RX0+ LVDS Differential Data Input Positive
7 GND Ground
8 RX1- LVDS Differential Data Input Negative
9 RX1+ LVDS Differential Data Input Positive
10 GND Ground
11 RX2- LVDS Differential Data Input Negative
12 RX2+ LVDS Differential Data Input Positive
13 GND Ground
14 RXCLK- LVDS Differential Data Input Negative
15 RXCLK+ LVDS Differential Data Input Positive
16 GND Ground
17 RX3- LVDS Differential Data Input Negative

18 RX3+ LVDS Differential Data Input Positive
19 GND GND
20 NC Reserved

(1)Connector Part No.: [Hirose] DF14H-20P-1.25H

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

(2)Matching socket Part No.: [Hirose] DF14-20S-1.25C

5.2 BACKLIGHT UNIT

Pin Symbol Description Color

1 HV1 High Voltage Pink/ Blue
2 LV Ground White/ Black

Note (1) Connector Part No.: BHSR-02VS-1 (JST) or equivalent

Note (2) Matching Connector Part No.: SM02B-BHSS-1-TB (JST) or equivalent

12 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

5.3 COLOR DATA INPUT ASSIGNMENT

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for

the color. The higher the binary input the brighter the color. The table below provides the assignment of

color versus data input.

Color

R7 R6 R5 R4 R3 R2 R1 R0 R7 R6 G5 G4 G3 G2 G1 G0 R7 R6 B5 B4 B3 B2 B1 B0

Basic
Colors

Gray
Scale
Of
Red

Black
Red
Green
Blue
Cyan
Magenta
Yellow
White
Red(0) / Dark
Red(1)
Red(2)

:

:
Red(252)
Red(252)
Red(252)

0
1
0
0
0
1
1
1
0
0
0

1
1
1

0

0

1

1

0

0

0

0

0

0

1

1

1

1

1

1

0

0

0

0

0

0

:

:

:

:

:

:

1

1

1

1

1

1

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Data Signal

Red Green Blue

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

0

0

0

0

0

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

1

1

1

0

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Green(0)/Dark

Gray
Scale
Of
Green

Gray
Scale
Of
Blue

Note (1) 0: Low Level Voltage, 1: High Level Voltage

Green(1)
Green(2)

:

:
Green(252)
Green(252)
Green(252)
Blue(0) / Dark
Blue(1)
Blue(2)

:

:
Blue(252)
Blue(252)
Blue(252)

0
0
0

0
0
0
0
0
0

0
0
0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

:

:

:

:

:

:

:

:

:

:

:

:

:

:

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

:

:

:

:

:

:

:

:

:

:

:

:

:

:

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

0

0

0

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

0

1

1

1

1

1

1

0

1

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

1

0

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

:

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

0

1

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

0

0

0

0

0

0

0

0

0

0

1

1

1

1

1

1

1

1

13 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

6. INTERFACE TIMING

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

The input signal timing specifications are shown as the following table and timing diagram.

Signal Parameter Symbol Min Typ Max Unit Remarks
DCLK

DATA

DE

Vertic al

Horizontal

Pixel clock Frequency Fck - 65 80 MHz
Pixel clock period Tck 12.5 15 20 ns

Duty ratio (%Tch) - 45 50 55 % Tch/Tck

High time Tckh 5 - - ns
Low time Tckl 5 - - ns
Setup time Tsd 4 - - ns
Hold time Thd 4 - - ns
Setup time Tsde 4 - - ns
Hold time Thde 4 - - ns
Vertical Frequency Fv - 60 75 Hz
Vertical display active period Tvda 768 768 768 Thp
Vertical display blank period Tvdb 1 38 - Thp
Vertical period Tvp 769 806 - Thp
Horizontal display active

period
Horizontal display blank period Thdb 76 320 776 Tck
Horizontal period Thp 1100 1344 1800 Tck

www.panelook.com

Thda 1024 1024 1024 Tck

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Note (1) Because this module is operated by DE only mode, Hsync and Vsync input signals should be set

to low logic level or ground. Otherwise, this module would operate abnormally.

14 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

T

DE

DE

768

www.panelook.com

INPUT SIGNAL TIMING DIAGRAM

Tvp

Thp

Tvda

Thda

2

768

Tvdb

1

Thdb

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

DCLK

DATA

DCLK

DATA

DE

Tckh

Valid display data (1024 Tck)

ckl

Tch

Tsde

Invalid Valid

Tck

0.7VDD

0.3VDD

Thd Tsd

0.7VDD

0.3VDD

Thde

0.7VDD

15 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

C

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

TIMING DIAGRAM of LVDS

TxCLK OUT

Rx

K IN

Rx IN3

Rx IN2

Rx IN1

Rx IN0

T

T/7

RxOUT23

RxOUT17

RxOUT16 RxOUT11 RxOUT10

RESERVED B07 B06 G07 G06 R07 R06

RxOUT26

RxOUT25 RxOUT24 RxOUT22

RxOUT21

DE GND GND B05 B04 B03 B02

RxOUT18

RxOUT15 RxOUT14 RxOUT13

RxOUT12

B01 B00 G05 G04 G03 G02 G01

RxOUT7 RxOUT6

RxOUT4

RxOUT3 RxOUT2

G00 R05 R04 R03 R02 R01 R00

RxOUT5

RxOUT20

RxOUT9

RxOUT1

RxOUT27

RxOUT19

RxOUT8

RxOUT0

16 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

6.2 POWER ON/OFF SEQUENCE

Power On

90%

www.panelook.com

Power Off

90%

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Restart

t4

Power Supply

for LCD, V

- Interface Signal

(LVDS Signal of
Transmitter), V

- Power for Lamp

Timing Specifications:

0 < t1  10 msec

0 < t2  50 msec

0 < t3  50 msec

0V

DD

0V

I

t4  1 sec

t5  100 msec

10%

t1

Valid Data

t6 t5

ONOFF OFF

10%

t3 t2

10%

t6  100 msec

Note (1) Please avoid floating state of interface signal at invalid period.

Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD V

to 0 V.

DD

Note (3) The Backlight inverter power must be turned on after the power supply for the logic and the

interface signal is valid. The Backlight inverter power must be turned off before the power supply

for the logic and the interface signal is invalid.

17 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

7. OPTICAL CHARACTERISTICS

7.1 TEST CONDITIONS

Item Symbol Value Unit
Ambient Temperature Ta
Ambient Humidity Ha
Supply Voltage
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
Inverter Current IL 5.5 mA

The measurement methods of optical characteristics are shown in Section 7.2. The following items

should be measured under the test conditions described in Section 7.1 and stable environment shown in

Note (4).

7.2 OPTICAL SPECIFICATIONS

Item Symbol Condition Min. Typ. Max. Unit Note

Contrast Ratio CR 250

Response Time

Center Luminance of White L 200 250 - cd/m

Red

Color
Chromaticity

Viewing Angle

Green

Blue

White

Horizontal

Vertic al

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

o

25±2

50±10

V

DD

TR -

-

T

F

Rx 0.607 0.637 0.667 ­Ry 0.323 0.353 0.383 ­Gx 0.272 0.302 0.332 ­Gy 0.558 0.588 0.618 -

=0°, qY =0°

q

x

Viewing Normal Angle

3.3 V

300

7

23

- - (2), (4)
22 ms
38 ms

Bx 0.111 0.141 0.171 -

By 0.064 0.094 0.124 ­Wx 0.274 0.304 0.334 ­Wy

qx+

q

x

qY+

q

Y

­CR³10

-

0.295 0.325 0.355 ­50 60 ­50 60 ­30 40 ­50 60 -

C

%RH

Deg.

2

(3)

(4)

(1), (4)

18 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (1) Definition of Viewing Angle (qx, qy):

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

qX- = 90º

x-

6 o’clock

q

y- = 90º

y-

Note (2) Definition of Contrast Ratio (CR):

The contrast ratio can be calculated by the following expression.

Normal

qx = qy = 0º

qy- qy+

qx-

qx+

y+

12 o’clock direction

q

y+ = 90º

x+

qX+ = 90º

Contrast Ratio (CR) = L63 / L0

L63: Luminance of gray level 63

L 0: Luminance of gray level 0

CR = CR (5)

CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (5).

Note (3) Definition of Response Time (T

100%

90%

Optical

Response

Gray Level 63

10%

0%

, TF):

R

Gray Level 63

Gray Level 0

Time

T

R

T

F

19 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Note (4) Measurement Setup:

The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt

temperature change during measuring. In order to stabilize the luminance, the measurement

should be executed after lighting Backlight for 20 minutes in a windless room.

LCD Module

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

LCD Panel

Center of the Screen

Field of View = 2º

500 mm

Photometer

(TOPCON BM-5A)

Light Shield Room

(Ambient Luminance < 2 lux)

20 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

8. PRECAUTIONS

8.1 HANDLING PRECAUTIONS

(1) The module should be assembled into the system firmly by using every mounting hole. Be careful not

to twist or bend the module.

(2) While assembling or installing modules, it can only be in the clean area. The dust and oil may cause

electrical short or damage the polarizer.

(3) Use fingerstalls or soft gloves in order to keep display clean during the incoming inspection and

assembly process.

(4) Do not press or scratch the surface harder than a HB pencil lead on the panel because the polarizer is

very soft and easily scratched.

(5) If the surface of the polarizer is dirty, please clean it by some absorbent cotton or soft cloth. Do not use

Ketone type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid or Methyl chloride. It might

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

permanently damage the polarizer due to chemical reaction.

(6) Wipe off water droplets or oil immediately. Staining and discoloration may occur if they left on panel for

a long time.

(7) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In

case of contacting with hands, legs or clothes, it must be washed away thoroughly with soap.

(8) Protect the module from static electricity, it may cause damage to the C-MOS Gate Array IC.

(9) Do not disassemble the module.

(10) Do not pull or fold the lamp wire.

(11) Pins of I/F connector should not be touched directly with bare hands.

8.2 STORAGE PRECAUTIONS

(1) High temperature or humidity may reduce the performance of module. Please store LCD module within

the specified storage conditions.

(2) It is dangerous that moisture come into or contacted the LCD module, because the moisture may

damage LCD module when it is operating.

(3) It may reduce the display quality if the ambient temperature is lower than 10 ºC. For example, the

response time will become slowly, and the starting voltage of lamp will be higher than the room

temperature.

8.3 OPERATION PRECAUTIONS

(1) Do not pull the I/F connector in or out while the module is operating.

(2) Always follow the correct power on/off sequence when LCD module is connecting and operating. This

can prevent the CMOS LSI chips from damage during latch-up.

(3) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while

assembling with inverter. Do not disassemble the module or insert anything into the Backlight unit.

21 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

9. PACKAGING

9.1 PACKING SPECIFICATIONS

(1) 5 LCD modules / 1 Box

(2) Box dimensions : 353(L) X 268(W) X 462(H) mm

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

(3) Weight : approximately 8.5Kg ( 5 modules per box)

9.2 PACKING Method

Figures 9-1and 9-2 are the packing method.

Figure. 9-1 Packing method

22 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

Figure. 9-2 Packing method

23 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

10. INCOMING INSPECTION DAY

The Supplier should be acquainted the inspection results (acceptance or rejection) by Customer, and the results

are in accordance with the incoming inspection standard within 30 days after the date of the bills of lading.

Should Customer fail to so notify the Supplier within the said 30 days period. The Customer’s right to reject the

LCMS shall then lapse, and the said LCMS shall be deemed to have been accepted by the customer.

24 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

11. DEFINITION OF LABELS

11.1 CMO MODULE LABEL

The barcode nameplate is pasted on each module as illustration, and its definitions are as following

explanation.

CHI MEI

OPTOELECTRONICS

(a) Model Name: M150X3 –L01

(b) Revision: Rev. XX, for example: C1, C2 …etc.

www.panelook.com

M150X3 -L01 Rev. XX

MADE IN TAIWAN

X X X X X X X Y M D L N N N N

Issued Date:Jan.18’2002

Model No.: M150X3-L01

Approval

E207943

MADE IN TAIWAN

(c) Serial ID: X X

Serial ID includes the information as below:

(a) Manufactured Date: Year: 1~9, for 2000~2009

Day: 1~9, A~Y, for 1

(b) Revision Code: cover all the change

(c) Color Filter: 0 ->CMO, 2 -> Toppan

X X X X X Y M D L N N N N

Month: 1~9, A~C, for Jan. ~ Dec.

Serial No.

Product Line

Year, Month, Date

CMO Internal Use

Color Filter

Revision

CMO Internal Use

st

to 31st, exclude I and O

(d) Serial No.: Manufacturing sequence of product

(e) Product Line: 1 -> Line1, 2 -> Line 2, …etc.

25 / 25

Version3.1

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CONTAINS A SMALL AMOUNT OF

MERCURY PLEASE FOLLOW LOCAL ORDINANCES OR REGULATIONS FOR DISPOSAL.

RISK OF ELECTRIC SHOCK.

DISCONNECT THE ELECTRIC

POWER BEFORE SERVICING.

HIGH VOLTAGE

CAUTION

MADE IN TAIWAN

E207943

M150X3 Rev. C1-L0C

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Document No.:
Issue Date: 2002/01/08
VERSION: 1.0 B

1
Address: No. 1, Chi-Yeh Road, Hsin-Shih Village,Tainan Science-Based Industrial Park,Tainan County, Taiwan 744 R.O.C.
TEL: [phone]

Inspection Specification

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Document No.:
Issue Date: 2002/01/08
VERSION: 1.0 B

Inspection Standards for LCD Modules

1.Description

These inspection standards shall be applied to LCD Module supplied by CHI MEI Optoelectronics

Corporation.

2.The environmental condition of inspection

The environmental condition and visual inspection shall be conducted as below.

(1) Ambient temperature : 15~25ʑ

(2) Humidity: 25~75 %RH

(3) External appearance inspection shall be conducted by using a single 20W fluorescent lamp or

equivalent illumination.

(4) Panel visual inspection on the operation condition for cosmetic shall be conducted at the distance

35cm or more between the LCD module and eyes of inspector. And, the viewing angle shall be 90

degree to the front surface of display panel.

Ambient Illumination: 300 ~ Lux for external appearance inspection

Ambient Illumination: 100 ~ 200 Lux for light on inspection

3.Method of sampling inspection

Unless defined in the other document, the sampling method shall be in accordance with

MIL-STD-105E.

(1) Lot size: quantity of per delivery for inspection per model.

(2) Sampling type: Normal inspection, Single sampling

(3) Inspection level: level II

(4) Sampling table: MIL-STD-105E

4.Classification of defects

Defects are classified two types, major defect and minor defect according to the defect. And, the

definition of defects is classified as below.

(1) Major defect

Any defect may result in functional failure, or reduce the usability of product for its purpose. For

example, electrical failure, deformation and etc..

(2) Minor defect

A defect that is not to reduce the usability of product for its intended purpose and un-uniformity, dot

defect and etc..

The criteria on major and/or minor judgement will be according with the classification of defects.

2
Address: No. 1, Chi-Yeh Road, Hsin-Shih Village,Tainan Science-Based Industrial Park,Tainan County, Taiwan 744 R.O.C.
TEL: [phone]

Inspection Specification

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Document No.:
Issue Date: 2002/01/08
VERSION: 1.0 B

5.Acceptable quality level (AQL)

AQL means that the quality level of product is acceptable for shipment, and the AQL shall satisfy

with customer’s quality request.

The AQL (%) for major or minor defect are expressed as below respectively.

(1) Major defect: 0.65

(2) Minor defect: 1.0

6.Inspection Criteria

(1) Definition of dot defect

a) The definition of dot: The size of a defective dot over 1/2 of whole dot is regarded as one defective

dot.

b) Bright dot: Dots appear bright and unchanged in size in which module is displaying

under black pattern.

c) Dark dot: Dots appear dark and unchanged in size in which module is displaying

at pure red ,green , blue picture.

d) 2 dot adjacent = 1pair = 2 dots

3
Address: No. 1, Chi-Yeh Road, Hsin-Shih Village,Tainan Science-Based Industrial Park,Tainan County, Taiwan 744 R.O.C.
TEL: [phone]

Inspection Specification

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Document No.:
Issue Date: 2002/01/08
VERSION: 1.0 B

(2) Electrical Inspection

Items Acceptable count

Random

2 dots adjacent

Bright dot

3 dots adjacent

4 dots or more adjacent(Green)

Random

Dark dot

2 dots adjacent

3 dots adjacent

4 ~ 6 dots adjacent

Minimum Distance Between Bright dots

Distance

Minimum Distance Between Dark dots

Minimum Distance Between Bright & Dark dots

Total bright and dark spot

Nɠ2

Nɠ1

Nɠ0

Nɠ0

Nɠ5

Nɠ1

Nɠ0

Nɠ0

Lɡ15mm

Lɡ5mm

Lɡ10mm

Nɠ5

Display failure (V-line/H-line/Cross line etc.) Not allowable

Mura Not visible through 6% ND filter.

(3) Appearance inspection

Item Standards

Foreign black/white spots,

Foreign lint

Polarizer Scratches

Dent/Air bubble

0.1ɝDɠ0.6 mm, Nɠ4

0.01ɝWɠ0.1 mm, 0.3ɝLɠ8.0 mm, Nɠ4

0.01ɝWɠ0.1 mm 0.3ɝLɠ10.0 mm, Nɠ4

Avg. Dɠ1.0 mm, Nɠ4

4
Address: No. 1, Chi-Yeh Road, Hsin-Shih Village,Tainan Science-Based Industrial Park,Tainan County, Taiwan 744 R.O.C.
TEL: [phone]

Inspection Specification

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

b

www.panelook.com

Document No.:
Issue Date: 2002/01/08
VERSION: 1.0 B

a

L

W

D=(a+b)/2 W: width, Lʚlength

7.Classification of defects

Inspection Item Criteria and Description Defect type

Vertical line Signal input, vertical line off or abnormal V-line appears major

Horizontal line Signal input, horizontal line off or abnormal H-line appears major

Cross line Pattern signal input, a correct display is not obtained major

No display Signal input, display is dead major

Abnormal display Pattern signal input, a correct display is not obtained major

Bezel claw Bezel claw missing or not bent major

Outline size Length, Wide, High, CCFT cable length major

Dots defect Exceed specified standards minor

Light leakage Visible light leakage appears around the edges of screen minor

Foreign material Exceed specified standards minor

Mura Exceed limit sample (Judged by limit sample) minor

External Appearance

Rust, deformation, irregular plating, coating missing etc.
A appearance defect that do not affect function or performance

minor

Polarizer bubble Exceed specified standards minor

Newton ring Newton ring is visible like ringed brightness uneven on pattern minor

5
Address: No. 1, Chi-Yeh Road, Hsin-Shih Village,Tainan Science-Based Industrial Park,Tainan County, Taiwan 744 R.O.C.
TEL: [phone]

Inspection Specification

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com