CMO G133I1-L02 Specification
Global LCD Panel Exchange Center
ಖᙕ
ՠ܂
ᐉு
ߡۥ
ދป
TFT LCD Approval Specification
MODEL NO.: G133I1 - L02
www.panelook.com
Issued Date: Aug. 26, 2008
Model No.: G133I1 - L02
Approval
Customer:
Approved by:
Note:
ʳ
2008-10-16
19:22:38 CSTʳ
The information described in this technical specification is preliminary and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
ʳ
PMMD
Directorʳ
ʳ
cs_lee(ޕݳᆣ
/17564/44926)ʳ
1 / 27
ʳ
Directorʳ Accept
ʳ
Version 2.2
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Aug. 26, 2008
Model No.: G133I1 - L02
Approval
- CONTENTS -
REVISION HISTORY ------------------------------------------------------- 3
1. GENERAL DESCRIPTION
1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
1.5 MECHANICAL SPECIFICATIONS
------------------------------------------------------- 4
2. ABSOLUTE MAXIMUM RATINGS ------------------------------------------------------- 5
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
2.2.2 BACKLIGHT UNIT
3. ELECTRICAL CHARACTERISTICS ------------------------------------------------------- 7
3.1 TFT LCD MODULE
3.2 BACKLIGHT UNIT
4. BLOCK DIAGRAM ------------------------------------------------------- 11
4.1 TFT LCD MODULE
4.2 BACKLIGHT UNIT
5. INPUT TERMINAL PIN ASSIGNMENT ------------------------------------------------------- 12
5.1 TFT LCD MODULE
5.2 BACKLIGHT UNIT
5.3 TIMING DIAGRAM OF LVDS INPUT SIGNAL
5.4 COLOR DATA INPUT ASSIGNMENT
5.5 EDID DATA STRUCTURE
6. INTERFACE TIMING ------------------------------------------------------- 16
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
6.2 POWER ON/OFF SEQUENCE
7. OPTICAL CHARACTERISTICS ------------------------------------------------------- 18
7.1 TEST CONDITIONS
7.2 OPTICAL SPECIFICATIONS
8. PRECAUTIONS ------------------------------------------------------- 22
8.1 HANDLING PRECAUTIONS
8.2 STORAGE PRECAUTIONS
8.3 OPERATION PRECAUTIONS
9. PACKING ------------------------------------------------------- 23
9.1 CARTON
9.2 PALLET
10. DEFINITION OF LABELS
10.1 CMO MODULE LABEL
10.2 CMO CARTON LABE
10.3 CUSTOMER CARTON LABEL
10.4 CUSTOMER PALLET LABEL
------------------------------------------------------- 25
2 / 27
The information described in this technical specification is preliminary and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.2
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Aug. 26, 2008
Model No.: G133I1 - L02
Approval
REVISION HISTORY
Version Date
2.0
2.1
2.1
2.2
2007.08.16
2008.04.28
2008.04.28
2008.08.26
Page
(New)
All
5
17
19
21
Section Description
All
Approval specification was first issued.
2.1
6.2
7.2
8.1
Vibration (Non-operation) test condition from
5Hz, 100Hz, 200Hz, 1.47Grms X, Y, Z three axes (30min /axis) to
1.5G, 10~300Hz, 10min/cycle,3 cycles each X,Y,Z
Contrast Ratio Modified, Typ. 500 -> 800
Min. 350 -> 550
Optical SpecificationΚModify note (5) measurement setup figure.
Add precaution of “Image sticking” in section 8.1 Assembly and
handling precautions
(11) Do not keep same pattern in a long period of time. It may cause
image sticking on LCD
3 / 27
The information described in this technical specification is preliminary and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.2
www.panelook.com
Global LCD Panel Exchange Center
1. GENERAL DESCRIPTION
1.1 OVERVIEW
G133I1 - L02 is a 13.3” TFT Liquid Crystal Display Rohs module and 20 pins LVDS interface. This module
supports 1280 x 800 WXGA mode and can display 262,144 colors. The optimum viewing angle is at 6
o’clock direction. The inverter module for Backlight is not built in.
1.2 FEATURES
- WXGA (1280 x 800 pixels) resolution
- DE only mode
- 3.3V LVDS (Low Voltage Differential Signaling) interface with 1 pixel/clock
- RoHs compliance
www.panelook.com
Issued Date: Aug. 26, 2008
Model No.: G133I1 - L02
Approval
1.3 APPLICATION
- TFT LCD Panel
1.4 GENERAL SPECIFICATI0NS
Item Specification Unit Note
Active Area 286.08 (H) x 178.8 (V) mm
Bezel Opening Area 289.1 (H) x 181.8 (V) mm
Driver Element a-si TFT active matrix - Pixel Number 1280 x R.G.B. x 800 pixel Pixel Pitch 0.2235 (H) x 0.2235 (V) mm Pixel Arrangement RGB vertical stripe - Display Colors 262,144 color Transmissive Mode Normally white - Surface Treatment AG , 25%Haze - -
1.5 MECHANICAL SPECIFICATIONS
Item Min. Typ. Max. Unit Note
Horizontal(H) 298.5 299 299.5 mm
Module Size
I/F connector mounting position The mounting inclination of the connector makes the screen
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
Vertical(V) 194.5 195 195.5 mm
Depth(D) - 7.7 8.0 mm
Weight - 450 465 g -
center within ±0.5mm as the horizontal.
(1)
(1)
(2)
Note (2) Connector mounting position
+/- 0.5mm
4 / 27
The information described in this technical specification is preliminary and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.2
www.panelook.com
Global LCD Panel Exchange Center
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Symbol
Operating Ambient Temperature TOP -30 +70 ºC (0), (1), (2)
Storage Temperature TST -30 +80 ºC (0), (1)
Test Item Test Condition Note
High Temperature Storage Test 80ºC, 240 hours
Low Temperature Storage Test -30ºC, 240 hours
Thermal Shock Storage Test
High Temperature Operation Test 70ºC, 240 hours
Low Temperature Operation Test -30ºC, 240 hours
High Temperature & High Humidity
Operation Test
Heat Cycle Operation Test
ESD Test (Operation)
Shock (Non-Operating) 200G, 2ms, half sine wave, 1 time for ± X, ± Y, ± Z. (2)(3)
Vibration (Non-Operating) 1.5G,10~300Hz,10min/cycle,3 cycles each X,Y,Z (2)(3)
-30ºC, 0.5hourЧШ80к, 0.5hour; 100cycles, 1hour/cycle
60ºC, 90%RH, 240hours
-20ºC, 1hourЧШ70ºC, 1hour; 50cycles, 4hour/cycle
150pF, 330Ө, 1sec/cycle
Condition 1 : panel contact, 8KV
Condition 2 : panel non-contact 15KV
www.panelook.com
Value
Min. Max.
Issued Date: Aug. 26, 2008
Model No.: G133I1 - L02
Approval
Unit Note
(1) (2)
(2)
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta Љ 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) No display malfunctions.
Note (3) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough
so that the module would not be twisted or bent by the fixture.
Note (4) Temperature of panel display surface area should be 80 ºC Max.
Note (5) In the standard conditions, there is no function failure issue occurred. All the cosmetic specification
is judged before the reliability test
5 / 27
The information described in this technical specification is preliminary and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.2
www.panelook.com
Global LCD Panel Exchange Center
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
Item Symbol
Power Supply Voltage VCC -0.3 +4.0 V
Logic Input Voltage VIN -0.3 VCC+0.3 V
2.2.2 BACKLIGHT UNIT
Item Symbol
Lamp Voltage VL 2.5k V
Lamp Current IL 2.0 7.0 mA
Lamp Frequency FL 50 80 KHz
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation
should be restricted to the conditions described under Normal Operating Conditions.
www.panelook.com
Value
Min. Max.
Value
Min. Max.
Unit Note
Unit Note
Issued Date: Aug. 26, 2008
Model No.: G133I1 - L02
(1)
(1), (2), IL = 6.5 mA
RMS
RMS
(1), (2)
Approval
Note (2) Specified values are for lamp (Refer to 3.2 for further information).
6 / 27
The information described in this technical specification is preliminary and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.2
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Aug. 26, 2008
Model No.: G133I1 - L02
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE Ta = 25 ± 2 ºC
Parameter Symbol
Min. Typ. Max.
Power Supply Voltage Vcc 3.0 3.3 3.6 V Permissive Ripple Voltage VRP 50 mV Rush Current I
1.5 A (2)
RUSH
Initial Stage Current IIS 1.0 A (2)
Power Supply Current
LVDS Differential Input High Threshold V
LVDS Differential Input Low Threshold V
White 330 370 mA (3)a
Black
Icc
TH(LVDS)
TL(LVDS)
450 490 mA (3)b
+100 mV
-100 mV
LVDS Common Mode Voltage VCM 1.125 1.375 V (4)
LVDS Differential Input Voltage |VID| 100 600 mV (4)
Terminating Resistor RT 100 Ohm
Note (1) The ambient temperature is Ta = 25 ± 2 ºC.
Value
Unit Note
Approval
(4),
=1.2V
V
CM
(4)
=1.2V
V
CM
Note (2) I
I
: the maximum current when VCC is rising
RUSH
: the maximum current of the first 100ms after power-on
IS
Measurement Conditions: Shown as the following figure. Test pattern: black
(High to Low)
(Control Signal)
SW
+12V
+3.3V
R1
47K
R2
1K
47K
VR1
C1
1uF
Q1 2SK1475
C2
0.01uF
Q2
2SK1470
FUSE
C3
1uF
Vcc rising time is 470us
+3.3V
0.9Vcc
Vcc
(LCD Module Input)
VCC
100ms
I
IS
0V
I
RUSH
470us
0.1Vcc
ICC
7 / 27
The information described in this technical specification is preliminary and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.2
www.panelook.com
Global LCD Panel Exchange Center
|
|
|
|
Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, fv = 60
Hz, whereas a power dissipation check pattern below is displayed.
www.panelook.com
Issued Date: Aug. 26, 2008
Model No.: G133I1 - L02
Approval
a. White Pattern
Active Area
Note (4) The parameters of LVDS signals are defined as the following figures.
CM
V
b. Black Pattern
Single Ended
Active Area
VID
Differential
0V
V
VID
0V
V
8 / 27
The information described in this technical specification is preliminary and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.2
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Aug. 26, 2008
Model No.: G133I1 - L02
3.2 BACKLIGHT UNIT Ta = 25 ± 2 ºC
Parameter Symbol
Min. Typ. Max.
Lamp Input Voltage VL 531 590 649 V
Lamp Current IL 2.0 6.5 7.0 mA
Lamp Turn On Voltage V
S
-- --
-- -Operating Frequency FL 50 -- 80 KHz (3)
Lamp Life Time LBL 50000 -- -- Hrs (5)
Power Consumption PL 3.84 -- W (4), IL = 6.5 mA
Note (1) Lamp current is measured by utilizing a high frequency current meter as shown below:
Value
1080(25к)
1290(0к)
Unit Note
I
RMS
(1)
RMS
V
(2)
RMS
V
(2)
RMS
Approval
= 6.5 mA
L
HV (Pink)
LCD
LV (White)
Module
1
Inverter
2
A
Current Meter
Note (2) The voltage that must be larger than Vs should be applied to the lamp for more than 1 second
after startup. Otherwise, the lamp may not be turned on normally.
Note (3) The lamp frequency may produce interference with horizontal synchronous frequency from the
display, and this may cause line flow on the display. In order to avoid interference, the lamp
frequency should be detached from the horizontal synchronous frequency and its harmonics as far
as possible.
Note (4) P
L
= I
LVL
Note (5) The lifetime of lamp can be defined as the time in which it continues to operate under the condition
Ta = 25 2
o
C and IL = 6.5 mArms until one of the following events occurs:
(a) When the brightness becomes or lower than 50% of its original value.
(b) When the effective ignition length becomes Љ 80% of its original value. (The effective ignition
length is a scope that luminance is over 70% of that at the center point.)
Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the
inverter must have specifications for the modularized lamp. The performance of the Backlight,
such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for
the lamp. All the parameters of an inverter should be carefully designed to avoid producing too
much current leakage from high voltage output of the inverter. When designing or ordering the
inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the
inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module
should be operated in the same manners when it is installed in your instrument.
The output of the inverter must have symmetrical (negative and positive) voltage waveform and
symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter
9 / 27
The information described in this technical specification is preliminary and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Version 2.2
www.panelook.com
Loading...