6-7.4. LIVE AUDIO ...................................................................................................................................41
6-7.4.1. COMMUNICATION BETWEEN MONITOR AND CLIENT COMPUTER VIA INTERNET .....42
6-7.4.2. COMMUNICATION BETWEEN MONITOR AND CAMERAS ................................................42
6-7.6. OSD ON / OFF ...............................................................................................................................44
6-7.7. PAN / TILT ......................................................................................................................................45
6-7.8. SYSTEM STATUS..........................................................................................................................48
6-7.9. POWER LOSS LISTS ....................................................................................................................49
6-7.10. VIDEO LOSS LIST.......................................................................................................................51
SYSTEM ........................................................................................................................... 79
7-2.1. SYSTEM NAME .............................................................................................................................80
7-2.2. LANGUAGE ...................................................................................................................................81
7-2.3. TIME / DATE ..................................................................................................................................81
7-2.4. SYSTEM CONFIG .........................................................................................................................83
7-3.3. Format ............................................................................................................................................91
7-7.1. IP Mode ........................................................................................................................................ 119
7-7.2. GATEWAY, SUBNET, IP ADDRESS............................................................................................120
7-7.3. Port ...............................................................................................................................................121
7-7.3.1 Port Forwarding .....................................................................................................................121
7-7.4. MAC ID.........................................................................................................................................121
7-7.5. MNS (MAC NAME SERVER) ......................................................................................................122
7-7.6. DDNS (DYNAMIC DOMAIN NAME SYSTEM)............................................................................123
7-7.7. HOW TO SETUP AND USE THE DDNS.....................................................................................125
8-4.4. Status ...........................................................................................................................................144
HOW TO OBTAIN FACTORY SERVICE ........................................................................................... 176
7
Stand-alone DVR Instruction Manual
8
About this manual
This is the Instruction Manual for 26” Wide TFT-LCD monitor built-in 16Ch DVR system,
Model LCD26164, LCD26168 and LCD261616.
The last digit(s) of the model numbers (e.g.: 4, 8 and 16) represent the number of cameras
included in the system.
This Manual describes how to install and operate the 26” Wide TFT-LCD monitor built-in
16Ch DVR system and provides specifications and features.
Please read this manual thoroughly and follow the installation process before using the
system.
Note : Be sure to correctly follow step 3. What to do at the time of installation.
Contact our distributors or dealers when you have any queries.
9
Stand-alone DVR Instruction Manual
10
1
1.Unpacking
Care should be taken when unpacking to avoid damaging the system.
Please check that the following items are included:
26” LCD Monitor built-in 16 Ch DVR
2-Indoor camera with C-mount lens
2-Outdoor camera with mounting bracket
Host Program (DvrMaster) on CD
2-Mounting bracket for indoor cameras
4-6pin Din 60’ cables
Remote Controller
2-Batteries
USB Mouse
AC Power Cable
Instruction Manual
RJ-45 Cable
Warranty registration card
Quick setup guide
Mounting bracket hole cover
Note: Contact your dealer immediately if any components are missing.
11
Stand-alone DVR Instruction Manual
1-1. 26” Wide LCD Panel Built-in 16 Ch Digital Video Recorder
LCD26164 isthe most reliable and functional embedded DVR system available today. The
system displays 16 channels of live images in Real Time speed, compresses data digitally and
records them to the Hard Disk Drive, which can be replayed and searched easily any time.
The LCD26164 supports easy back up via USB port, external Hard Disk Drive and networking in
both static & dynamic IP modes.
User can remotely view live images or search the recorded images.
Under emergency situation, the remote operator can control, turn on and turn off the field
installed alarms, such as a siren or light.
It is a very user- friendly DVR system. User can control the LCD26164 by Mouse or Buttons on
the side panel or Remote controller.
12
2
▶ 26” Wide Screen
- High resolution TFT-LCD 1,366(H) x 768(V), Contrast ratio 700:1, Response time 8 msec ▶ Multi Functional Record
- Powerful, multiple Record Modes available: Manual (Continuous), Timer, and Motion
Detection Recording.
▶ User friendly GUI
- A few simple buttons for Easy control.
▶ Automatic System Recovery
- Automatic and Complete System recovery within 10 seconds.
▶ Easy PTZ control via RS port
- No need to use PTZ controller
- PTZ control from remote PC
▶ Networking
- DHCP based automatic network set-up-Easy Network Configuration from Dynamic IP to
Dynamic IP
- Support TCP/IP and Remote Control on all DVR features
- Up to 10 users can remote access the system through DVRMaster (GUI) or Internet
Explorer simultaneously.
- DDNS support
▶ MPEG-4 Algorithm Compression
-The most advanced compression available today.
▶ High Resolution DVR 720 x 480
- Real time display 480 Frames/sec
- Recording speed 480 Frames/sec based on 360x240
- Programmable display resolution and recording speed on each channel
▶ 2 Way Audio
- Communicate between the system and cameras or between the system and client computer through the internet
▶ Easy Data Playback in any PC
- Back Up data convertible to AVI file format.
▶ Back UP
- External HDD, Stick memory, and through network access.
▶ Desktop or Wall-mountable
2.Features
13
Stand-alone DVR Instruction Manual
14
3
The system should be installed in the following order;
1. Make sure all the required hardware is available.
2. Connect the cameras to the monitor (Refer to Fig 5-3).
4. Confirm if live video is displayed on the monitor before going to the next step.
5. Select the Setup Menu and set current date and time (Refer to Section 7-2.3).
6. Run the FACTORY DEFAULT setting in the SYSTEM menu.
7. Perform HDD formatting.
8. Escape from Setup Menu.
9. Set values for required options.
10. Network cable should be connected to the monitor before turning the power on.
3.What to do at the time of
Installation
- 26” wide TFT-LCD monitor built-in 16 Ch DVR
- Up to 16 cameras capacity (Refer to the retail box for the number of camera
included in the system).
- CCTV monitor or TV set if necessary
- Network cable if connecting to a PC
Refer to Fig 5-8 for the cable specification.
15
Stand-alone DVR Instruction Manual
16
/
4
4.Specifications
ITEM DESCRIPTIONS
VIDEO SIGNAL
VIDEO FEATURES
AUDIO FEATURES G.723 8ch Input / 1ch Output
RECORD
SEARCH
BACKUP
Recorded data lock Data protection in overwrite HDD Time range, Back up
USER INTERFACE
NETWORK Ethernet 10/100M Auto TCP/IP, DHCP, MNS server
EMAIL
NOTIFICATION
PC Program
USB USB 2.0 for external DVD R/W, CD R/W, HDD, USB memory
SERIAL RS485 16 camera Pan/Tilt, Remote control
ALARM
HDD SATA 750GB (Refer to the retail box)
POWER
CONNECTORS
MECHANICAL
ENVIRONMENT
Television System NTSC PAL
Refresh Rate 60 fields/sec 50 fields/sec
Video Resolution 720x480 720x576
Video Inputs 8- 6pin Din Cameras and 8- BNC Cameras
Video Input Signal Composite 1.0 Vp-p 75 Ohms
Video Output 1- Composite output
Video Output Signal Composite 1.0 Vp-p 75 Ohms
Live 480 Frames/sec display 400 Frames/sec display
Zoom 2 times digital
Sequence Sequence display in Full size
Display Format 1 screen(full), Quad pages split, 9 split pages, 16 split
Camera Video enhance Brightness, Contrast control on each cameras
LCD Display enhance Brightness, Contrast, saturation, 4:3 or 16;9 selectable
Recording Speed 480 Frames/sec 400 Frames/sec
Recording resolution
Codec Mpeg4
Recording Timer, Motion, Alarm, Manual individually set
Pre record 0~30 sec
Material SATA HDD(Auto overwrite)
Manual, Timer ,Motion, Alarm, Each
Camera, All Camera
External HDD, USB memory,
through Network
GUI RGB 24bit full color
Operating interface Mouse, Keypad, IR remote controller, Network
SMTP Server
Remote viewer Same as DVR monitor (Mouse or Key button)
PC Player
Alarm Inputs 8 Inputs
Alarm Outputs 1 Relay Output(1A max)
Alarm Latch up 1~30 sec
Buzzer Out On/Off
Input Voltage AC 110V/ 220V 50~60Hz (Free voltage)
Power consumption Approx. 200W
Video Inputs 8- 6pin DIN & 8 BNC
Video Output 1 RCA for slave monitor
Audio Output 1 RCA for Speaker
Alarm In/Out
RS485 2pin terminal block
Ethernet RJ45
Mouse USB mouse
- Do not place this product near a bathtub, kitchen sink, wet basement, over a radiator, or heat
generator.
▫ Installation of the system on the wall
- Place the system on the flat surface with soft fabric as shown in Fig. 5-4-1.
- Separate the mounting bracket by removing three screws on the rear of the system as
shown in Fig.5-4-1.
- Cover the mounting bracket hole with the provided lid as shown in Fig. 5-4-2.
- The wall mounting bracket is not included in the system and refer to the manufacturer’s
instructions on how to install it to the wall.
25
Stand-alone DVR Instruction Manual
Note:
- Pay attention to not make scratches or dents on the surface of panel (screen)
during installation of the system.
- In case of this, the warranty will be voided.
5-4.2.1. Connection of Composite Monitor
If necessary, connect the composite Video Output (yellow RCA) and Audio Output (white
RCA) to Video IN and Audio IN on a composite monitor or TV (RCA cable: not included).
5-4.3. Sensor Connection and RELAY IN &OUT
▫ SENSOR Connection (SENSOR IN)
Connect up to 8 sensors to ALM (SENSOR) IN. The Sensors should be contactor type and
support N.O. (Normal Open).
ALARM IN
12345678
[Fig 5-5 Sensor In]
G
▫ALARM OUT Connection
When necessary, use ALARM OUT. The ALARM OUTPUT is a relay contactor type and
supports N.O. (Normal Open) and N.C. (Normal Close). The Output capacity is 220V 1A. A
higher capacity can cause system failure.
ALARM OUT
[Fig 5-6 Alarm Output]
N/C
RS485
N/O
+
GND
COM
-
26
5. Installation
5-4.4. RS485 Connection
▫ Connect the cable to the “RS485 PORT” on the terminal block of the system.
Refer to[Fig 5-7] for connection of Connector PIN
ALARM OUT
N/C
[Fig 5-7 RS485 Connection]
RS485
N/O
+
GND
COM
-
5-4.5 Connection to an Ethernet Network (Optional)
▫Connecting the cable to Ethernet.
Our Ethernet connector is a RJ45 type. The maximum cable length is 300 ft. When you want
to use a longer cable, we suggest using repeater.
Refer to
[Fig. 5-8] for connector pin configuration.
[Fig 5-8 Straight-through & Crossover Cable]
27
Stand-alone DVR Instruction Manual
5-4.6. POWER CABLE CONNECTION
▫ Connect the provided AC power cable to the monitor and an AC outlet. AC input voltage is AC
110V to 220V 50/60Hz.
It should not be shared with other electrical equipment on the same line.
Frequent power cuts can cause crucial failures, so if you have an unstable power source we
recommend the use of an Uninterrupted Power Supply or other backup power source.