CloudWalker SPECTRA 43AF04X User Manual

43AF04X

SPECTRA LED TV

#

ATTENTION:

Standard

Energy Saving’ settings’ under the ‘Set-up’ menu.

Mode.

.

Caution................................................................................................2

Safety Information..............................................................................3

Accessories........................................................................................6

Multimedia Terminal Connection......................................................9

Wall Mount Installation......................................................................7

Antenna Connection........................................................................11

Media Operation...............................................................................14

Menu Operation................................................................................15

ON-OFF Power..................................................................................11

Front View.........................................................................................11

The Remote Control.........................................................................12

Specifications...................................................................................19

Simple Troubleshooting...................................................................21

Stand Assembly Instruction..............................................................6

Install and Connect TV.......................................................................8

Contents

The exclamation mark Inside an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions.

The lighting flash with the arrowhead symbol, inside an equilateral triangle is intended to apprise the user of the presence of uninsulated dangerous voltage within the products enclosed which may be a sufficient magnitude that may cause a risk of electric shock to the user.

Safety Information To ensure reliable and safe operation of this equipment, please read all the instructions in

this user guide, especially the safety information below.

The TV set should only be connected to a main power supply as stated on the label on the back of the product. To prevent overload, don’t share the same main supply socket for too many items.

Electrical safety

Do not place any connecting wires where they may be stepped on or tripped over. When removing the plug from the wall socket, make sure to pull the plug and not the wires. During a thunderstorm or while leaving the TV for long periods, disconnect the aerial ( if outdoor ) and mains from the power supply.

Do not allow water or moisture to enter the TV or main adaptor. Do not use the tv in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.

Pull the plug out immediately, and seek professional help if :

The main plug or cable is damaged. Liquid is spilt onto the set, or if it is accidentally exposed to water or moisture. Anything accidentally penetrates the ventilation slots. The set does not function properly. Do not remove the safety covers. There are no user serviceable pacts inside. You may invalidate the warranty. Only qualified personnel can service this apparatus. Remove exhausted batteries from the remote control handset to avoid battery leakage or if case you are not using it for a long period. Physical safety Do not block ventilation slots in the back cover. You may place the TV near cabinet, but please ensure that there is at least 5cm (2") clearance all around. Do not lap or shake the TV screen. You may damage the internal circuits. Take good care of the remote control, do not drop it. To clean the TV use a soft dry cloth. DO NOT use solvents or petrol based fluids. For stubborn stains, you may use a damp soft cloth with diluted detergent.

Warning: An apparatus with CLASS I construction shift should be connected to the MAIN socket outlet with a protective earthing connection. Where the MAIN plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

This product contains electrical or electronic materials The presence of these materials may if not disposed of properly have potential adverse effects on the environment and human health.

.

Presence of this label on the product means that it should not be disposed of an unsorted waste and must be collected separately. As a consumer, you are responsible for ensuring that this product is disposed of properly. You may contact us at the contact details shared in this manual.

Please Recycle

Caution

2

WARNING

To reduce the risk of fire or electric shack, do not expose this apparatus to rain or moisture.

The apparatus should not be exposed to dripping or splashing liquids and no objects filled

with liquids, such as vases, should be placed on the apparatus.

1. Read this instructions.

2. Keep these instructions.

3. Note all warnings.

4. Follow all instructions.

5. Do not use the this apparatus near water

6. Clean the television only with a dry cloth.

7. Do not block any of the ventilation openings.

Install the television in accordance to the

manufacturer’s instructions.

8. Do not install TV set near any heat source

such as radiators, heat registers, stoves or

produce heat.

other apparatus (including amplifiers) that

9. Do not defeat the safety purpose of the

polarized or grounding type plug. A polarized

plug has two blades with one wider than the

other. A grounding type plug has two blades

and a third grounding prong. The wide blade

or the third prong is provided for your safety.

outlet, consult an electrician for replacement

of the obsolete outlet.

When the provided plug does not fit into your

10. Protect the power cord from being walked

on or pinched particularly at plugs.

manufacturer.

11. Use only the accessories specified by the

IMPORTANT SAFETY INSTRUCTIONS

Safety Information

3

12. Use only a cart, stand, tripod, bracket,

or a table apeded by the manufacturer

or which is solid with the apparatus.

13. Unplug this apparatus during lightning

storms or it is to be unused for a long time.

Note :

CAUTION connecting the Power Cord

a qualified service personnel. Servicing is

14. Share all the servicing requirements with

required when the apparatus has been

damaged in any way.

15. Never place the TV, remote control or batteries near naked flames any other heat source, including direct sunlight. To prevent the spread of fire, keep candles or other flames away from the TV, remote control and batteries at all times.

Do not overload wall outlets. Overloaded wall outlets could damage the TV and could result in electric shock or fire. Frequently examine the cord of your appliance. If its appearance indicates damage or deterioration, unplug it and stop using it until you have it replaced with a cord authorized by your dealer. Protect the power cord from physical or mechanical abuse such as being twisted, kinked or pinched.

16. The USB terminal should be loaded with 0.5A under normal operation.

17. The company will provide the customer with the first wall mount free of cost,any changes or new wall mounts hence forth will be chargeable.

18. The company suggests that the TV should be mounted at eye level to get the best

viewing experience.If the customer wishes to place it at any other angle then the

viewing experience may differ accordingly.

19. Once the LED/LCD TV has been mounted,the responsibility of its maintenance lies with the customer.The company is in no way liable for any damages that may

occur due to falling/dust gathering/moisture accumulation etc.

20. If the set is cold,there may be a small flicker when the set is switched on. This is

normal and there is nothing wrong with the set.

- If the TV is cold, there maybe a small flicker when you turn it on.

- Avoid touching the LCD screen or holding your finger (s) against it.

21. Some dot defects of bright or dark colors may appear on the screen.However, this will not have any impact or effect on TV performance.

4

Safety Information

5

E-WASTE DISPOSAL

Environmental compliances:

As per the rules laid down by the Government for environmental concern & safety, your product has been made to comply and conform to the respective regulation as listed below. This product falls under the E-WASTE (MANAGEMENT) RULES, 2016 of Ministry of Environment, Forests & Climate Change.

RoHS declaration:

This Product is in conformity with the requirements of Rule 16 of the E-WASTE (MANAGEMENT) RULES, 2016. The content of hazardous substances with the exemption of the applications listed in SCHEDULE ll of the E-waste (Management) Rules, 2016 is as follows:

1. Lead (Pb): not over 0.1% by weight;

2. Mercury (Hg): not over 0.1% by weight;

3. Cadmium (Cd): not over 0.01% by weight;

4. Hexavalent Chromium: (Cr6+): not over 0.1% by weight;

5. Polybrominated Biphenyls (PBBs): not over 0.1% by weight;

6. Polybrominated Diphenyl Ethers (PBDEs): not over 0.1% by weight.

Information under E-Waste (Management) Rules, 2016

For disposal of E-waste, please call our helpline no. or visit our website.

Do’s and Don’ts for disposal of product:

1) Do’s :

a. Always drop your used electrical/electronic products, batteries, cables, adapters and packaging materials after the end of their life at the nearest authorized collection point/center. b. Separate the packaging material according to their respective waste disposal options and sorting for recycling. c. The batteries can be easily removed from the product for recycling.

2) Don’ts : a. Never dump E-waste in Garbage bins or Municipal solid waste stream. b. Do not dispose your product as unsorted municipal waste. c. Do not throw or dispose used, damaged and leaking batteries & products into house hold waste.

Use only the matching screws provided by the manufacturer in the accessories

bag in order to install the TV Unit stand and also in order avoid damaging the TV unit.

2. You may reverse the steps to remove the base stand from the TV.

Follow these instructions to install the Base Stand of the TV.

3. Please keep the TV in a horizontal position and fix the standing base with screws.

2. Please lay the TV on the table, face down.

1. Please disconnect all the cable connections before installation.

1.

NOTE :-

Stand Assembly Instruction

User Manual & Warranty Card

Wall Mount

Remote Control

Stand

4 Stand Support screws

2 Batteries (AAA)

Please make sure the following items are included with your LED TV. If any items are missing, please contact your dealer.

Wall Mount

+

Screw the base stand with TV stand bush through the ST 4*20MM screw.

Accessories

6

AV Cable

.

. .

.

. .

.

VD43F801

S P

1 32

64 5

7 98

0

++

VOL

++

--

CH

ENTER

REPEAT

FB

STOP

FF NEXT

EXITMENU

MUTE

ZOOM

RECALLDISPLAY

BLUEGREEN

S.MODE P.MODE

YELLOW RED

PREV.

A-B

CH.LISTFREEZE

SOURCE

PLAY/PAUSE

St.By

43AF04X

SPECTRA LED TV

Fix the TV on the wall

3. Please also check the strength of the wall before installation; professional assistance may be required for the same.

6. Once the bracket is installed, verify that it is firm and

secure at its place.

7. Now hold the TV and allow the top adapters on the back

side of the TV within the bracket slots..

2. Take two white colored adapters and fix them to top two hole on the backside of the TV with the help of fasteners (provided with adapters). Take two black colored adapters and fix them to bottom two holes on the backside of the TV with the help of fasteners.

4. Drill three holes on the wall and install the wall bracket with the help of fasteners.

5. Maintain minimum distance in all four sides from TV as shown in Fig 2.

200mm

100mm

1. First, place the TV on the table smoothly and cover the table surface with foam sheet/

clothes to avoid scratching on the TV screen.

Screw Size

M6*18mm

M6*22mm

10cm

30cm

7

Wall Mount Installation

Note :- Images may be different from actual TV model.

Place your TV at a firm place which can bear the weight of the TV. To avoid any danger, please don’t expose the TV near water or any heat source (such as light, candle, heating machine). Also, do not block the ventilation at the back of TV.

1. Connect the antenna cable to the antenna socket on the back of the TV.

2. To plug the power cord of TV.

Mounting on a table

Connect Antenna and power

ANTENNA Cable

AC 110-240V ~ 50/60 Hz

RF IN

(ANTENNA)

3. Press the power button of the TV the indication light will turn to green. If the TV is in standby mode ( the light is red), press the power button on the remote control or on the TV.

Maintain minimum space from the wall for proper ventilation as show in image.

Turn On TV

NOTE :-

10cm

30cm

Install and Connect TV

8

Note :- Images may be different from actual TV model.

Multimedia Terminal Connection

9

Please switch off the power when connecting the TV to an external device. The TV can play different multimedia sources by connecting different terminals with multimedia devices such as DVD Players, PC's etc. and selecting a corresponding input source.

PC AUDIO IN

HDMI 1

HDMI 2

ANT (RF IN)

AV 2 IN MINI

AV OUT

USB 1 INUSB 2 IN

AV 1 IN

AV 2 IN (MINI)

TV terminal

Note:-

R

Audio Audio

Audio

Video Video

Video

R

L L

L

Multimedia terminal

R

W

Y

AV 2 IN

PC IN

AUDIO IN-R

AUDIO IN-L

VIDEO

(EARPHONE OUT)

HEADPHONE OUT

AV 1 IN

..

...

.

..

. .

.

..

.

..

...

.

..

. .

.

..

.

..

...

.

..

. .

.

..

.

...

.

. .

.

...

..

.

...

.

. .

.

...

..

.

...

.

. .

.

...

..

.

...

.

. .

.

...

..

.

...

.

. .

.

...

..

.

...

.

. .

.

...

..

.

...

.

. .

.

. .

...

..

.

...

.

. .

.

. .

...

..

.

...

.

. .

.

. .

...

..

.

...

.

. .

.

...

..

.

...

.

. .

.

...

..

.

...

.

. .

.

...

..

.

AV Cable are often color-coded to connectors. Connect ® red to red, white to white, yellow to yellow.

W

Y

Multimedia Terminal Connection

10

PC IN

TV terminal

AV OUT

PC

Audio IN

Audio

VGA

L

R

Multimedia terminal

W

R

Y

Display Device

HDMI 1/HDMI 2

Headphone

(Earphone)

USB 1/USB 2

Multimedia terminal

TV terminal

TV terminalTV terminal

HDMI

Headphone

USB IN

R

W

Y

..

...

.

..

. .

.

..

.

..

...

.

..

. .

.

..

.

..

...

.

..

. .

.

..

.

...

.

...

..

.

...

.

...

..

.

...

.

...

..

.

...

.

...

..

.

...

.

...

..

.

...

.

...

..

.

HDMIHDMI

Computer

. .

Antenna Connection

11

300 OHM FLAT CABLE

300 OHM

To TV ANTENNA JACK

75 OHM DIN

Connect the 75 OHM coaxial cable from the antenna to the antenna socket on the rear panel as shown above.

Note :

VHF TV ANTENNA

UHF TV ANTENNA

For better reception, especially in outlying areas or where ghost effect or interference occur, an external roof-mounted antenna is recommended.

proper connection to the antenna jack (The adaptor is not supplied).

75 OHM ADAPTOR

75 OHM COAXLIAL CABLE

Front View

ON-OFF Power

Connect the AC main lead to the household power outlet.

Note :

Unplug the AC main lead from the power outlet when not using it for a long period of time.

Note : Please refer actual product for Image.

5

3

2

1

Standby or switch on the TV.

Display or exit MENU.

Press it to display input source list. Press it continuously to

MENU

SOURCE

5

1

2

4

3

1

POWER

VOL+/-

To be used to adjust volume and have the same function with [ ] / [ ] buttons of remote control when operating in menu.

MENU

SOURCE

V+ V-

CH+

CH-

4

To be used to change channels and have the same function with [ ] / [ ] buttons of remote control when operating in menu.

CH+/-

Installing The Remote Control Batteries

1. Remove the battery cover.

2. Insert two “AAA” batteries into the remote control. Make sure that the (+) and (-) symbols on the batteries match the (+) and (-) symbols inside the battery compartment.

3. Replace the cover and press down unit the lock snaps closed.

4. Point the remote control to wards the remote sensor located on the TV unit.

5. When there is a strong ambient light source, the performance of the infrared remote sensor may be degraded, causing unreliable operation.

6. The recommended effective distance for remote operation is about 16 feet (5 meters).

7. When the batteries become weak and the operating distance of the remote control is greatly reduced, you will need to replace the batteries.

CAUTION : Danger of explosion may occur if battery is incorrectly replaced.

• If the remote control is not going to be used for a long period of time, remove

on

the batteries to avoid damage caused by battery leakage or corrosion.

• Do not mix old and new batteries or ALKALINE or standard

(CARBON-ZINC) or rechargeable (NICKEL-CADMIUM) batteries.

• Always remove batteries as soon as they become weak.

• Weak batteries can leak and severely damage the remote control.

•

Point the remote control to wards the TV but not more than 5 meters from the Remote control sensor in the TV and within 60°in front of the TV. The operating distance may vary depending upon the brightness of the room.

Remote Control Operation Range

30 30

5m

S P

1 32

64 5

7 98

0

+

-

VOL

+

-

CH

ENTER

REPEAT

FB

STOP

FF NEXT

EXITMENU

MUTE

ZOOM

RECALLDISPLAY

BLUEGREEN

S.MODE P.MODE

YELLOW RED

PREV.

A-B

CH.LISTFREEZE

St.By

SOURCE

PLAY/PAUSE

“AAA” BA

TTERY

“AAA” BATTERY

+

12

The Remote Control

28. RECALL ( )

Return to the previous channel after channels have been changed.

Introduction to the remote control function.

1. St. By ( )

Standby or switch on the TV.

1

9

14

13

12

11

15

10

2

4

6

8

3

5

7

9. S. MODE

Cycle through different sound settings.

8. RED / GREEN / YELLOW / BLUE

Channel Edit when setting up your TV.

2. FREEZE

This key will function to freeze.

3. CH. LIST

Press this button to display the channel tuned list of RF mode.

S P

1 32

64 5

7 98

0

++

VOL

-

++

-

CH

ENTER

FB

FF NEXT

EXITMENU

MUTE

ZOOM

RECALL

DISPLAY

BLUEGREEN

S.MODE

P.MODE

YELLOW RED

PREV.

SOURCE

St.By

CH.LISTFREEZE

REPEAT STOPA-B

PLAY/PAUSE

16

23

26

27

25

28

24

17

19

21

18

20

22

4. A-B

Select A-B repeatedly. Press once to set to A and press again to set to B then press for the third time to cancel in USB.

5. REPEAT Select the repeat mode in USB.

6. Previous ( )

Play previous in USB mode.

7. FB ( )

Play back faster. Play the previous page in the TEXT Media.

22. FF ( )

Play forward faster. Play the next page in the TEXT Media in USB.

20. STOP ( )

Stop and back to the folder interface.

19. PLAY/PAUSE ( )

Play or pause.

14. 0-9

Select the TV channel you want to view by using the number buttons.

15. DISPLAY

Display info of the current channel.

13. VOL +/-

Increase/decrease the TV’s volume level.

11. MENU

Display or exit MENU.

10. CURSOR BUTTONS ( )

Up / Down / Left / Right.

12. MUTE ( ) Reduces the TV’s volume to its minimum level. Press again to restore the volume.

16. SOURCE Display the input source list. Press the [ / ] button or the [SOURCE] button to select the input source you want. Press the [ENTER] button of the [ ] button to select the desired source.

18. FAV. LIST

Display or cancel the favorite list. When you set up a favorite channel, press this button to display the favorite list. Press the [ / ] button to select the channel. Press the [ENTER] button to play.

17. FAV +

Channel favorite channel up

21. NEXT ( ) Play next in USB mode.

23. P. MODE

Cycle through available vide picture modes.

24. ENTER

Confirms your selection.

25. EXIT Exit the menu system.

26. CH +/- Channel up/down.

27. Zoom

Works as Aspect Ratio button : Select the aspect ratio of the screen.

13

The Remote Control

USB1 to USB2 Copy and vice versa

The USB storage devices should be inserted into the terminal. Select the media source and view the multimedia. If you want to exit the multimedia you can choose other sources.

MENU Operation During Play

[ / ]: Select.

[ ENTER ]: Confirm.

[ DISPLAY ]: Select menu when playing a file.

[ EXIT ]: Quit the entire menu.

MENU Operation

[ EXIT ]: Return to root menu

The icon of the menu [ ]: Return to root.

[ / ]: Select media or select file.

[ / ]: Select file.

[ ENTER ]: Confirm or play.

USB 2.0

PHOTO MUSIC MOVIE TEXT

1. Insert USB’s in both USB 1 and USB 2 ports.

2. Select the source USB 1 or USB 2

3. Select the type of file whatever image/Music/Video

4. Then press red key on remote (COPY) for copy function

5. Then Copy will start automatically from USB 1 to USB 2 or USB 2 to USB 1 as per selection,

The file will go in the similar folder as of the Source USB. i.e.

A. If Video file is selected from Source, it will go to next usb in Video folder B. If Image file is selected from Source, it will go to next usb in Image folder C. If Music file is selected from Source, it will go to next usb in Music folder

Menu Menu

Select to reduce picture size. (Related to JPEG file)

Zoom out the picture first. Highlight the icon and press the [ENTER] button then press the [ / ] / [ / ] button to move the picture. (Related to JPEG file)

Select A-B repeatedly. Press once to set to A and press again to set to B then press for the third time to cancel.

Select playing time. Preset [ / ] to select, [0-9] to adjust. Press the [ENTER] button to select playing time.

Play slower.

Play the movie step by step.

Select aspect ratio.

Play or stop the background music. (Music file and playing file in one folder) (Related to JPEG file)

Select to enlarge picture size.(Related to JPEG file)

Rotate counter clockwise. (Related to JPEG file)

Rotate clockwise. (Related to JPEG file)

Show playlist.

Display or cancel file information. When playing video, some items can be adjusted Press [ / ] to select, press [ / ] to adjust. Select close, press [ENTER] to exit.

[ / ]: select, [ / ]: switch, [ ENTER ]: confirm.

i

Mute or cancel mute

Function Function

Introduction of media ( Photo, Music, Movie, Text) control function.

Media Operation

14

Enter Menu

Menu Operation

Exit Menu

Auto Tuning

ATV Manual Tuning

[ MENU ] : Display menu.

[ / ] : Select menu.

[ ENTER ] or [ / ]: Enter menu.

[ / ] : Select

[ ENTER ] : Enter the sub menu or confirm.

[ / ] : Adjust or enter the sub menu.

Press the [ MENU ] button to return to the previous menu or exit the current menu

or press the [ EXIT ] button to exit menu.

Press the [ ENTER ] button or the [ ]

If you want to stop searching, press the

button to start Auto Search,

[ MENU ] button or the [ EXIT ] button.

button to cancel.

Press the [ ] button confirm or the [ ]

• Current CH : Set the channel number.

• Color System : Select the color system.

• Sound System : Select the sound system.

• Fine - Tune : Adjust the frequency of the channel finely.

• AFC : Automatic fine tuning.

• Search : Press the [ / ] button to search.

CHANNEL

Auto Tuning

ATV Manual Tuning Programme Edit

Move Menu Enter

Enter

Exit

Menu

TV: 5Programme(s)

44%... 433.75MHZ (TV)

44%...433.75MHZ (TV)

Menu

Current CH

Colour System

Sound System

AFC

Search

1 +

PAL

BG

49.7MHZ

–

TV: 5 Programme

Menu Operation

15

Programme Edit

Picture Mode : Select the picture mode that you

feel comfortable with.

Contrast/Brightness/Color/Tint (NTSC only)

Sharpness : These settings can be adjusted when

the Picture Mode is set to User.

that you feel comfortable with.

Color Temperature : Select the color temperature

Noise Reduction : You can clear up the input signal by setting the item.

Sound Mode : Select the sound mode that you

feel comfortable with.

Treble/Bass : These settings can be adjusted

Balance : Adjust the level of sound coming from

the left and right speakers.

Auto Volume : When Auto Volume is On, it will level out sudden changes in the

when the Sound Mode is set to User.

volume when it occurs during commercial breaks or channel changes.

Surround Sound

[ RED ] : Delete the current channel.

[ GREEN ] : Rename.

Press the [ / ] button to select the character.

[ YELLOW ] : Move.

Press the [ / ]button to select the figure.

Press the [ ENTER ] button to confirm.

Press the [ / ] button to select the position.

[ BLUE ] : Skip the selected channel.

Your TV set will skip the channel automatically.

Press the [ YELLOW ] button to confirm.

when using the [ CH+/- ] button to view the channels.

Fav

Add or Delete the channel to your favorite list.

Option available for adjustment may be different in different signal sources, but functions of the same option will be the same.

Audio Out : Adjust the volume of sound out put

Move Menu Enter

Enter

Exit

PICTURE

Picture Mode Standard

Contrast Brightness Color

Sharpness

Noise Reduction

50 50 50 50 50

Medium

Middle

SOUND

Sound Mode Standard

Move Menu Enter

Enter

Exit

Bass

Balance

Auto Volume

Audio Out

Surround Sound

50

0

Off

50

Off

Delete Rename Move Skip

Enter

||#

1

2

3

4

5

6

7

8

9

10

Programme Edit

Fav Menu

FAV

Menu Operation

16

PICTURE

SOUND

Sleep Timer : Select the time in minutes that you want the TV shut off

Clock : Press / button to select Clock, then

Off Time : Press / button to select Off Time

On Time : Press / button to select On Time

and Press / button to set Off to Once or Every

Day, then press ENTER button to select.

press ENTER button to select.

Auto Sleep : Select the time in hours that you want the TV to remain on after

OSD Timer : Set the OSD display time.

your last operation. Cancel by setting it to Off.

automatically. Cancel by setting it to Off.

Aspect Ratio : Set the aspect ratio of the screen.

Blue Screen : Set the background color when

Key Lock : Lock the control panel key of TV.

there is no input signal to either blue or black.

TIME

OPTION

OSD Language : Only English

1212

66

33

11

5577

22

1010

4488

99

4:3,16:9 Zoom 1,Zoom 2, Just scan Full

4:3,16:9 Zoom 1,Zoom 2 4:3,16:9 Zoom 1,Zoom 2 Point to Point 4:3, 16:9

Auto 16:9 (HD) 4:3,16:9 Zoom 1,Zoom 2

Source

TV

AV 1/2

VGA

HDMI

USB

Aspect Ratio modes available

Move Menu Enter

Enter

Exit

TIME

Off

Off Time

Clock

Sleep Timer

On Time

Auto Sleep

OSD Timer

Off

_ _ _ _

Off

15s

1212

66

33

11

5577

22

1010

4488

99

Move Menu Enter

Enter

Exit

OPTION

OSD Language English

Aspect Ratio

Blue Screen

Key Lock

Hotel Mode

Reset Software Update (USB)

16 : 9

On

Off

Menu Operation

17

Auto Adjust : Automatically adjust.

Vertical Pos. : Shift the screen up or down.

Horizontal Pos. : Shift the screen left or right.

Clock : Adjust the scaling of image in horizontal.

Phase : Adjust the internal signal phase.

SCREEN

Hotel Mode : Set hotel mode ON or OFF. Note : The

following settings work only when Hotel Mode is set to

be ON.

Source Lock : Lock the input source which you want.

Default Source : Set the default input source when

turning on your TV. Clear Lock Recall the default

default settings in hotel mode.

Default Prog : Set the default program when turning on your TV. Max Volume : Set the max volume that you can adjust. Channel Lock : Disable all features in the channel menu.

Default Volume : Set the default volume every time you switch on the

TV, the default volume is 30.

Clear Lock : Recall the default settings in hotel mode.

Set Password : Set the password as you like.

Note :- One time password for Hotel mode is 0000.

Connect the PC terminal to computer, and select PC source.

HOTEL MODE

SCREEN

Horizontal Pos.

Clock

Phase

50

49

Move

Menu

Enter

Exit

HOTEL

Hotel Mode Source Lock Default Source Default Prog

Channel Lock

Clear Lock Set password

Off

1

100

Off

30

Menu Operation

18

Note :

improvement.

Specifications

19

1. Model No.

2. Power

3. Input/Output Port

4. Speaker Output

5. Dimension of the unit

6. Net Weight

7. Gross Weight

10. Work Temperature

12. Storage Temperature

13. Storage Himidity

11. Work Humidity

8. Wall Mount Size

9. Wall Mount Screw Size

Number Of Pixels

Screen Size

Input Voltage

Audio IN

ANT (RF IN)

AV 1 IN

AV 2 IN (Mini)

HDMI

USB

AV OUT

HEADPHONE (Earphone)

VGA

(Without Stand)

Power Consumption

Stand by consumption

109cm

1920(H) x 1080(V) Full HD

110-240V~50/60Hz

75W

< 0.5W

1

7.4kg

10.9kg

5°C~45°C

20%~80%

10%~80%

-15°C~45°C

200mm x 100mm

Dimension Between Screws

M6 x 22mm 2Nos. Top M6 x 18mm 2Nos. Bottom

10W x 2

(W x D x H)

970mm x 80mm x 570mm

2

43AF04X

USB multimedia playback format:

Media

Movie

Music

Photo

File system : FAT32, FAT16, NTFS (NTFS compressed file is not supported).

Max. HDD Capacity : 500GB

File Ext.

Codec

AudioVideo

Remark

.avi

mp4

.ts/.trp

.mkv/.mov

.mpg

.dat

.vob

.mp3

.jpg/.jpeg

.bmp

.png

Note :-

(1). Specifications are subject to change without notice. (2). Files downloaded from the internet some time may not be playable in the LED TV, incase any one of the above mentioned specification is not met. Please scan USB Multimedia file for viruses and ensure that it is virus free. Incase of virus in the USB Multimedia file, LED TV may develop a problem. (3). Please ensure to fix and remove USB drive, when LED TV in off condition only.

MJPEG

Xvid, MPEG-2, MPEG-4, H.264

MPEG-2, MPEG-4, H.264

MPEG-2, H.264

MPEG-4, H.264

MPEG-1, MPEG-2

MP3

MP-2, PCM

Max Resolution And Frame Rate :

640x480@30fps Max Date Rate : 10Mbps

Max Resolution And Frame Rate :

1080p@30fps Max Date Rate : 20Mbps

Max Resolution: 352X288 Max Data Rate: 20Mbps

Max Resolution: 720x576 Max Data Rate: 20Mbps

Channel: Mono/Stereo

Max Resolution: 1027x768

Max Resolution: 15360x8640

Max Resolution: 9600x6400

Max Resolution: 1200x800

MP2

MP3

MPEG-1

MPEG-2

- -

Progressive JPEG

Baseline JPEG

--

Non-interfaced

Interfaced

(4) If a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is “image burn” or and not covered by the warranty. (5) If the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letter boxed area of the screen. (6) Avoid displaying a fixed image on the TV screen for a long period of time (2 or more hours for LCD, 1 or more hours for the Plasma TV) to prevent image burn. (7) “The TFT LED panel uses a panel consisting of sub pixels which requires sophisticated technology to produce. However, there may be a small number of bright or dark pixels on the screen. These pixels are normal and will have no impact on the performance of the product.”

Specifications

20

If the display fails or the performance dramatically changes, check the display in accordance with the following instructions. Remember to check the peripherals to pinpoint the source of the failure. If the display still fails to perform as expected, contact the dealer for assistance.

Symptom

No Power

No Sound

Remote not responding

The Screen Flashes in VGA Mode

Some interference in The VGA Mode

Abnormal Color

TV set needs to be cleaned

Check the power connection. Pull the plug out, wait for 60 seconds, then reconnect the power and turn on the set.

Increase the volume. Check if the set is on the mute state or not. Check the voice setting condition. Check the voice mode setting condition.

Check the effect of the batteries. If necessary replace the batteries or clean the remote control sensor window. The distance between the set and the remote control should be less than 6 meters.

The parameter is too big. Please use safety mode when restarting the PC and set the parameter of the monitor according to the instructions.

Modify parameter of the monitor according to the instruction manual.

Check the antenna connection.

DEALING METHOD

Simple Troubleshooting

21

Paste Serial No. Sticker here

#

CloudWalker SPECTRA 43AF04X User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual