Page 1
7 in 1 Grooming Kit
User Guide
Now you have purchased a Close Touch product
you can rest assured in the knowledge that as well as
your 3 year warranty you can also contact our dedicated
Help lines and Web support
After Sales Support
AFTER SALES SUPPORT
UK / N.IRELA ND HELPLINE NO 0845 54 3 9028
REP. IRELAN D HELPLINE NO 1 800 997 841
WEB SUPPORT in fo @gianiuk. co .uk
MODEL NUMBER: 40887
Page 2
Page 3
Contents
01 Introduction
02 General Caution
03 Extra Safety Precautions
04 Features
05 Getting Started
06 Other Useful Information
07 FAQ’s
08 Warranty Card
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
1.
Page 4
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
Welcome
1
Congratulations on choosing to buy a Close Touch product.
By doing so you now have the assurance and peace of mind that comes with
purchasing a product made by one of Europe’s leading manufacturers.
All products brought to you by Close Touch are manufactured to the highest
standards of performance and safety, and, as part of our philosophy of customer
service and satisfaction, are backed by our comprehensive 3 Year Warranty.
Warranty
Please ll in and return the Warranty Card to the address provided.
We hope you will enjoy using your purchase for many years to come.
In the unlikely event of your 7 in 1 Grooming Kit breaking down during use,
please telephone the number shown in the red "After Sales Support" label,
quoting Close Touch 40887 as the product number. If your 7 in1 Grooming Kit is
within the 3 year warranty period, it will be repaired or replaced free of charge.
The warranty will become null and void if the product is found to have been
deliberately damaged, misused or disassembled.
This warranty does not aect your statutory rights.
2.
Page 5
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
General Caution
The following safety precautions should always be followed, to reduce the risk of electric shock,
personal injury or fire. It is important to read all of these instructions carefully before using the
product, and to save them for future reference or new users.
This product must only be used as intended in accordance with enclosed operating instructions.
Do not carry the appliance by the mains cable or pull the cable to remove the plug from the socket.
Electrical appliances must always be stored in a secure place, out of reach of children.
Do not use outdoors. This appliance is designed for domestic indoor use only.
This product is not a toy. Do not allow children or any person unfamiliar with these instructions
to use this appliance.
Avoid positioning the appliance where the power cable might be accidentally trapped or damaged.
Do not operate this appliance if the cable or plug becomes damaged. A qualified electrician must
always carry any repairs that are necessary.
Switch off the power supply or unplug from the mains socket when not in use, before cleaning
or changing accessories
Keep the appliance and cable away from sources of heat, sharp objects or anything that may cause
damage.
Keep all ventilation slots, filters etc. uncovered and clear of debris. Never drop or insert any objects
into the openings.
Always ensure that hands are dry before operating or adjusting any switch on the product
or touching the plug or mains supply connections
Ensure that the appliance is switched OFF before connecting to the mains supply. Be aware that
some surfaces may become hot. Do not touch and supervise accordingly.
To protect against electric shock, never allow the appliance, the mains cable or plug to come into
contact with water or any liquid.
Never reach for any appliance that has fallen into water. Switch off the power supply at the mains
immediatley and unplug. Do not re-use until the product has been inspected and approved by
a qualified electrician.
Never leave the appliance unattended when connected to the live mains power supply.
To disconnect , first ensure that all controls are in the OFF position, then remove the plug from the
electricity supply.
If the appliance stops unexpectedly or appears to malfunction, switch off the power supply,
unplug from the mains and stop using immediatley. Seek professional advice to rectify the fault
or make repairs.
necessary when the appliance is used near children.
BATHROOM.
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• Close supervision is
• DO NOT USE IN THE
3.
Page 6
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
4.
Extra Safety Precautions
3
Page 7
Features
4
PRECISION
TRIMMER
FULL SIZE
TRIMMER
CLEANING BRUSH
NOSE, EAR &
EYEBROW TRIMMER
MICRO
SHAVER
HAIR CLIPPER
COMB
STORAGE
BASE UNIT
BEARD &
MOUSTACHE COMB
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
5.
Page 8
Getting Started
5
Read this important information before you
use your 7in1 Grooming Kit
TO CHARGE/RECHARGE
BE CERTAIN THE GROOMER IS OFF
•
Fully charge Groomer before using for
the rst time or after non-use for at
least 10 hours.
•
Battery performance is best if you recharge
only when the battery is (almost)
completely empty.
•
Charging or recharging at temperatures
below 40˚F or higher than 95˚F adversely
aects life span of the battery.
YOU MAY CHARGE THE GROOMER:
•
In the storage base unit by
inserting the appliance
plug into the socket located
in the bottom of the
groomer and placing the
groomer on the storage
base unit. (g.1).
•
By inserting the appliance
plug directly into the
Groomer (g.2).
Fig 1
Fig 2
CHARGING
PLUG INTO 240V AC OUTLET. USE ONLY THE
CORD PROVIDED, AFTER A FEW MOMENTS
THE GREEN CHARGING INDICATOR LIGHT ON
THE POWER PLUG WILL LIGHT TO INDICATE
THE GROOMER IS CHARGING.
It will take approximately 10 hours to fully
charge the Groomer for a cordless trimming
time of up to 35 minutes. Disconnect the
cord and unplug from electrical outlet.
OPTIMISE THE WORKING LIFE OF
THE BATTERY
After the Groomer has been charged for the
rst time, do not recharge the Groomer
between trimming sessions. Continue using
it until the battery is completely empty.
Do not charge for more than 24 hours.
Do not keep cord permanently plugged in.
Discharge/rundown the battery completely
twice a year by letting the motor run until
the battery is at. If the Groomer hasn’t been
used for a long period of time, it must be
recharged for a full 10 hours.
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
6.
Page 9
Getting Started
5
Put the AccuControl comb on the
full width trimmer attachment
until you hear it click into place
(g.3). The AccuControl comb
WILL NOT work with the smaller
neckline and sideburn trimmer, or micro
shaver attachments.
Press the Hair Length Selector and
slide it to the desired trimming
length setting. The selected setting
number will appear in the window to
the left of the Hair Length Selector
(g.4). See Table 1 for settings.
Fig 3
Fig 4
CORDLESS TRIMMING
Charge according to directions. Unplug
Personal Groomer from the charging base.
Slide ON/OFF switch ON to begin trimming.
If the battery is empty and you want to trim
your beard, charge the Groomer for at least
3 hours and you will have enough power
for one use (10 minutes).
ACCUCONTROL SYSTEM
The unique AccuControl System puts you
in complete control while trimming your
facial hairs with no prior experience
needed. The exing Guide Comb adjusts
automatically to hug the contours of your
face for a trim that is both even and
accurate, and it’s easy to manoeuvre over
those hard to reach areas such as the neck
and chin. The Hair Length Selector allows
you to choose among 9 preset hair lengths
and clicks into position so you can control
the exact hair length you desire or vary the
length of your facial hair.The Hair Clipping
Comb also features 9 preset hair lengths
and clicks into position so you can control
the exact hair length you desire.
TRIMMING
Make sure hair is clean and dry. Always comb
the hair with the styling comb in the direction
of growth before you start trimming. Do not
move the Groomer too fast. Make smooth and
gentle movements.
TRIMMING YOUR BEARD AND
MOUSTACHE WITH ACCUCONTROL
GUIDE COMB ATTACHMENT
Use this Groomer for its intended household
use as described in this manual. Make sure
that the Groomer is fully charged before you
start trimming.
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
7.
Page 10
Getting Started
5
• If you are trimming for the rst time, start by
using the AccuControl comb at the maximum
trimming length setting (#9) to prevent
accidentally trimming hairs too short. As you
become familiar with the settings, adjust
Hair Length Selector to desired trimming
length. Selector will “click” into position at
each setting.
• Switch the Groomer ON.
• To trim in the most eective
way, move the Groomer
against the direction of hair
growth. Make sure the
surface of the Guide Comb
always stays in contact with
the skin (g.5).
NOTE: Since all hairs do not grow in the same
direction, you may want to try dierent
trimming directions (i.e. upwards, downward or
across). Practice is best for optimum results.
If a lot of hair has accumulated in the Guide
Comb, remove the comb and blow and or/
shake the hair out of the comb. You can also
use the cleaning brush provided to remove
hair from the comb area.
•
Fig 5
TABLE 1. BEARD TRIMMER
SETTIN REMAINING HAIR
LENGTH (MM)
1 Stubble 2
2 Closely cropped 4
3 Short 6
4 Medium short 8
5 Medium 10
6 Medium long 12
7 Long 14
8 Extra Long 16
9 Longest 18
REMEMBER:
You must reset the hair length selector
back to your desired setting every time
you replace the guide comb on the
appliance. The remaining hair length
corresponds with the smallest distance
between the cutting blade and the spot
where the comb is in contact with the
skin. Cutting without the comb
attachment or setting the AccuControl
guide comb to #1position will result in
a stubble beard look.
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
8.
Page 11
Getting Started
5
BEARD TRIMMING WITHOUT
ACCUCONTROL GUIDE COMB
Remove AccuControl guide comb if you are:
• Dening hair lines
• Trimming nape of neck
• Removing single, unwanted hairs
• Be certain the Groomer is in the
OFF position
• Remove the AccuControl comb attachment
by pressing and sliding the Hair Length
Selector upwards (g.6)
• Never pull o the AccuControl comb
attachment by grasping the exible top
portion. Always pull o by the bottom part
of attachment.
• Switch the Groomer on
• Make well-controlled movements.
Touch the hair/ skin lightly with
the Groomer.
DEFINING BEARD, MOUSTACHE
AND SIDEBURN
• Be certain the Groomer is in the
OFF position
• Remove the AccuControl comb attachment
by pressing and sliding the Hair Length
Selector upwards (g.6)
• Detach the full width trimmer attachment by
pushing the release button (g.7)
• Put the smaller neckline and sideburn
trimmer attachment on the Groomer (g.8).
You will hear a click.
• Hold the Groomer upright when
you use the smaller neckline and
sideburn trimmer attachment
(g.9).
USING NOSE, EAR & EYEBROW
ATTACHMENT
• Be certain the Groomer is in the
OFF position.
• To attach or remove nose, ear,
eyebrow attachment (or change
attachments):
• Remove the AccuControl comb
attachment (g.6).
• Remove the full width trimmer
attachment by pushing the
release button (g.7)
• Put the nose, ear, eyebrow
attachment on the Groomer
(g.10). You will hear a click.
TRIMMING NOSE HAIR
• Make sure nasal passages
are clean.
• Place nose, ear and eyebrow
attachment on Groomer.
• Switch the Groomer on and insert
the tip of the attachment into one
nostril (g.11).
Fig 6
Fig 8
Fig 9
Fig 10
Fig 7
1
2
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
9.
Page 12
Getting Started
5
CAUTION: Do not insert the tip more than
3
/
16
inch/ 5mm into your nostril.
• Slowly move the tip in and out
while turning it around at the same time in
order to remove unwanted hair. For best
results, make sure the side of the tip is rm
against skin. This will reduce the tickling
eect that can occur during trimming of
nose hair.
• Turn o Groomer. Wipe attachment clean
after each use.
TRIMMING EAR HAIR
• Clean outer area of ear and ear canal. Make
sure it is free of wax.
• Nose, ear and eyebrow attachment should be
on the Groomer.
• Switch the Groomer on and move the tip
softly around the edge of ear to remove hairs
extending beyond the outer ear (g.12).
• Carefully insert the tip into outer
ear canal.
CAUTION: Do not insert the tip further than
3
/16 inch/ 5mm into the ear as this could
cause damage to the eardrum (g.13).
• Turn o Groomer. Wipe attachment clean
after each use.
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
10.
Page 13
Getting Started
5
TRIMMING EYEBROWS
Nose, ear and eyebrow
attachment should be
on Groomer.
Switch the Groomer on and use
the tip to cut individual
eyebrow hairs.
The Groomer can be used for
clipping single long hairs.
Put the Groomer at the root of
the hair and move it along the
edge of the eyebrow from the
base of the nose towards the
outer tip of the eyebrow in the
direction of hair growth (g.14).
IMPORTANT: Do not use the
Groomer to dene or trim the
entire eyebrow.
Do not try to trim your eyelashes.
Turn o Groomer. Wipe after each use.
Fig 12
Fig 13
Fig 14
Fig 15
Fig 11
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
11.
Page 14
Getting Started
5
CLEANING
• Do not use water or a moist cloth
to clean the Groomer.
• Always switch Groomer OFF before cleaning.
• Do not use abrasive, scourers or liquids such
as alcohol, benzene, bleach or acetone to
clean the Groomer.
• Never clean, replace or remove Groomer
attachments with motor ON.
• Do not apply pressure to cutters
• Do not touch cutters with hard objects as
this may damage them.
• Do not use while bathing, showering or
immerse the Groomer in water or other
liquids as damage to Groomer may occur.
DURING USE:
• If cut hairs have accumulated in the Guide
comb area, remove hairs by shaking,
blowing or using cleaning brush provided.
Remember to adjust the trimming length
back to your selected setting when you
replace the guide comb on Groomer.
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
12.
Page 15
Getting Started
5
CLEANING ONCE A WEEK
Make sure the Groomer is
switched OFF and
disconnected from the
electrical outlet.
Remove any attachment
Also separate the top part of
the micro shaver attachment
from its body (g.25).
Blow and/or shake out any hair
that may have accumulated in
the attachment.
The shaving foil is very delicate
and should not be handled
If foil becomes damaged,
replace it. Do not apply
pressure to shaving foil.
Do not clean the foil with
the brush, as this may
cause damage.
Place the attachment back on
the Groomer or place it in the
storage stand.
Fig 25
Fig 26
Fig 27
Fig 28
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
13.
Page 16
Other Useful Information
6
GUARANTEE AND SERVICE
This product has been manufactured
under the strictest of quality control
procedures, and using the highest
quality of materials to ensure excellent
performance and reliability. Provided
the appliance is properly used and
maintained it should give long lasting
performance.
This appliance comes with a full 36
months manufacturers guarantee that,
should the appliance stop working
within this period then the manufacturer
will repair or replace the item – provided
that the defect is not found to be a
consequence of the product having
been misused, i.e. connected to an
incorrect voltage, or used contrary to
the instructions, or subject to accidental
damage, neglect or inexpert repair. If you
have any problems with this appliance
please contact the helpline number on
the front of this manual.
If the appliance is opened for
whatever reason then the guarantee
will not be valid.
Your statutory rights are not aected.
Manufactured in China for:
Giani Limited
River House, Unit 17 Shepley Ind Est
Audenshaw, Manchester
M34 5DW
Tel: 0161 336 2200
Fax: 0161 336 2280
E-Mail: info@gianiuk.co.uk
CONFORMITY
The CE marking has been axed to the
product in accordance with the following
European Directives.
The conformity declaration is held
by the distributor:
Giani Limited, River House, Unit 17
Shepley Ind Estate, Audenshaw,
Manchester,
M34 5DW
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
Technical Specication
•
Input Voltage: 230V ~
•
Frequency: 50Hz
•
Output Voltage: 3V D.C.
•
Current: 300mA
14.
Page 17
Frequently Asked Questions
What should I do if the unit does not work?
Ensure the unit is fully charged.
What can I do to make my grooming kit last longer?
Do not wrap the power cord around the transformer.
Clean the attachments after each use.
Unplug the transformer after each charging session.
Fully discharge the unit every six months approximately.
How long do I initially charge the unit for?
10 hours.
7
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
15.
Page 18
Page 19
Page 20
7 IN 1 GROOMING KIT
3 YEAR WARRANTY CARD
Giani Limited
River House, Unit 17
Shepley Industrial Estate,
Audenshaw, Manchester
M34 5DW
Tel: 0161 336 2200
Name
Address
Email Tel No
Model No. 40887
Location of purchase
Helpline No. UK/Northern Ireland: 0845 543 9028
Helpline No. Rep. Ireland: 1 800 977 841
Web Support: www.aldiwarranty.com
Model Number: 40887
Description of Fault:
18.
Loading...