CLOROX Total 360, CLX1000 Operator's Manual

Download

Page 1

Electrostatic Sprayer CLX1000

115VAC, 60Hz, 7.0 A

Indoor Commercial Use Only

Operator’s Manual

1221 Broadway Oakland, CA 94612

1-800-492-9729 www.cloroxtotal360.com

| 1

Page 2

Table of Contents

SAFETY NOTICES

Warnings 3

Safety Decal 4

Protective Gear 5

IMPORTANT SAFETY PRECAUTIONS

Power Connection 5

Grounding Instructions 5

Extension Cord 5

Shock/Electrical Hazard 6

General Safety 6

Chemicals 6

SYSTEM COMPONENTS

Clorox Total 360™ Base Unit 7

Clorox Total 360™ Sprayer 7

Nozzle 7

OPERATING INSTRUCTIONS

Preparing the Spray Area 8

Unit Operation/Setup 8

Sprayer Operation During Cleaning 8

Changing Clorox-Approved Products 8

After Use and Storage 8

MAINTENANCE

Sprayer Body 9

Air Filter 9

Peristaltic Pump 9

Nozzle 9

SPECIFICATIONS 10

TROUBLESHOOTING 10

EQUIPMENT WARRANTY 11

Page 3

SAFETY NOTICES

This manual contains information that is important for you to know and understand before operating the Clorox Total 360™ Electrostatic Sprayer. This information relates to protecting your safety and ensures product reliability and performance. It is the owner’s responsibility to ensure that all who operate this equipment read this manual.

Warnings

To help you recognize this information we use the warning symbols below. Please read the manual carefully and pay special attention to the symbols and warning labels. Warning labels indicate a potentially hazardous situation which, if not avoided, could result in death or serious injury.

WARNINGS

• Read and fully understand the Clorox Total 360™ Electrostatic Sprayer Operators Manual prior to using the electrostatic sprayer.

• Read and fully understand Clorox-approved product labels prior to using any liquid product with the Clorox Total 360™ Electrostatic Sprayer.

• Clorox Total 360™ Electrostatic Sprayers are for indoor commercial use ONLY.

• Clorox Total 360™ Electrostatic Sprayers should never be used in a hazardous environment.

• Clorox Total 360™ Electrostatic Sprayers should never be used in an area containing volatile chemicals. Nor should it be used in any area containing volatile or explosive levels of gas, vapor or particulates.

• Clorox Total 360™ Electrostatic Sprayers should never be used by untrained personnel.

WARNINGS

PRESSURIZED EQUIPMENT HAZARD

Fluid from equipment that leaks or ruptures from a component can splash in the eyes or on skin, causing serious injury. In order help prevent a leak or rupture:

• Check hoses, tubes and couplings daily. Replace worn or damaged parts immediately.

WARNINGS

PLASTIC PARTS CLEANING SOLVENT HAZARD

Many solvents can degrade plastic parts and cause them to fail, which can lead to serious injury or property damage. In order to help prevent against degradation:

• Use only compatible water-based solvents to clean plastic structural pressure containing parts.

• See technical data in this and all other equipment instruction manuals. Read ﬂuid and solvent manufacturer’s SDSs and recommendations prior to use.

WARNINGS

FIRE, EXPLOSION AND ELECTRIC SHOCK HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent ﬁre, explosion and electric shock:

• Electrostatic equipment must be used only by trained, qualiﬁed personnel who understand the requirements of this manual.

• Stop operation immediately if static sparking occurs or you feel shock. Do not use equipment until you identify and correct the problem.

• Use and clean equipment only in wellventilated area.

• Never spray a ﬂammable chemical (with a ﬂashpoint less than 60˚C).

• Do not plug or unplug power cords or turn lights on or off when ﬂammable fumes are present.

• Keep spray area free of debris, including solvents, rags, gasoline or any ﬂammable chemicals.

• Keep a working ﬁre extinguisher in the work area.

| 3

Page 4

WARNINGS

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury.

• Recommend use of fully enclosed eyewear protections, such as goggles, when using this device.

• Refer to product speciﬁc Clorox Safety Data Sheets (SDS) for any additional PPE.

WARNINGS

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury

• Do not operate the unit when fatigued or under the inﬂuence of drugs or alcohol.

• Use ﬂuids and solvents that are compatible with equipment wetted parts. See technical data in all equipment manuals. Read ﬂuid and solvent manufacturer’s warnings. For complete information about your material, request SDS from distributor or retailer.

• Do not leave the work area while equipment is energized.

• Turn off all equipment when not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine replacement parts from trusted Clorox partners only.

• Do not alter or modify equipment. Alterations or modiﬁcations void your Clorox Total 360™ warranty, agency approvals and create safety hazards.

• Route hoses and power cords away from trafﬁc areas, sharp edges, moving parts and hot surfaces.

WARNINGS

CHEMICAL USE HAZARD

Each chemical, such as a disinfectant, has a unique set of hazards and needs to be handled properly to ensure worker safety.

• The Clorox Total 360™ Electrostatic Sprayer can only be used with products that have been approved by Clorox. Never spray any liquid product that is not a Clorox-approved product. The Clorox Total 360™ Electrostatic Sprayer warranty is voided if the Clorox Total 360™ Electrostatic Sprayer is used with products that are not approved by Clorox. Be aware that many chemical liquids can be harmful if they are not used properly.

• Read and understand the Clorox-approved product’s SDS and label prior to use.

• Be aware of ﬁrst aid procedures related to the product in use.

• It is a violation of Federal law to use a chemical in a manner inconsistent with its label.

• Use personal protective equipment as detailed by the Cloroxapproved product’s SDS.

• For use with non-ﬂammable, non-combustible and non-volatile ﬂuids only. Never spray a ﬂammable chemical (ﬂash point less than 60˚C) .

• Insure the area being sprayed has proper ventilation.

• Store all chemicals in original containers in a cool, dry place, away from heat and open ﬂames.

• Do not reuse or reﬁll a chemical container.

• To dispose of Clorox-approved products refer to product labels.

Safety Decal

This decal is located on the top-most deck surface forward of the bottle storage location.

Page 5

Protective Gear

Personal Protective Equipment (PPE) must comply with the American National Standards Institute, ANSI Z87.1-1989 standard if purchased after July 5, 1994, or ANSI Z87.1-1968.

• Eye and face PPE shall be distinctly marked to facilitate identiﬁcation of the manufacturer. [1910.133(a)(4)].

• The following minimum requirements must be met by all protective devices. Protectors shall:

- Provide adequate protection against the particular hazards for

which they are designed.

- Be of safe design and construction for the work to be performed.

- Be reasonably comfortable when worn under the designated

conditions.

- Fit snugly and not unduly interfere with the movements

of the wearer.

- Be durable.

- Be capable of being disinfected.

- Be easily cleanable.

- Be distinctly marked to facilitate identiﬁcation only

of the manufacturer.

RECOMMEND USE OF FULLY ENCLOSED EYEWEAR PROTECTIONS, SUCH AS GOGGLES, WHEN USING THIS DEVICE. ALWAYS USE APPROPRIATE PPE, LISTED ON THE CLOROXAPPROVED PRODUCT’S SAFETY DATA SHEET (SDS). CLOROX SDS’S CAN BE FOUND AT WWW.CLOROXPROFESSIONAL.COM/SDS

IMPORTANT SAFETY PRECAUTIONS

When using an electrical appliance, it is important to understand that some circuits are electrically live, even when the power switch is in the off position. Basic safety precautions should always be followed to reduce the risk of burns, ﬁre, electrical shock, injury and/or death.

Power Connection

Our power plug must be used with a 3-prong grounded outlet, rated for no less than 15A service. Always verify before product use. This appliance is for use on a nominal 120V/60Hz circuit with a veriﬁed ground plug. Check with a qualiﬁed electrician to insure you have the correct electrical service and grounding.

Grounding Instructions

This appliance must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Never use an adapter with this product.

DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green, with or without yellow stripes, is the equipment-grounding conductor. If repair or replacement of the cord or plug is necessary, do not connect the equipment-ground conductor to a live terminal. Check with a qualiﬁed electrician or serviceman if the grounding instructions are not completely understood or if in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance — if it will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician. Never use an adapter with this product.

Extension Cord

Clorox provides a 25-foot extension cord with each Total 360™ Electrostatic Sprayer and strongly recommends that you use this approved extension cord. Make sure your extension cord is in good condition. Inspect cords periodically and replace if damaged. If an alternate extension cord is used, be aware that an undersized extension cord will cause a drop in-line voltage, which could result in loss of power, damage to the product and/or overheating. Always use a sufﬁciently rated extension cord.

IMPORTANT: Clorox recommends using a 12/3 gauge extension cord, no longer than 100 feet (30.5m). Additionally, Clorox also recommends the use of a GFCI (ground fault circuit interrupter) power outlet or extension cord. When equipped on the extension cord, always position the GFCI toward the power outlet.

| 5

Page 6

Shock/Electrical Hazard

As with most electrical appliances, electrical parts are electrically live even when the switch is off. To reduce the risk of burns, ﬁre, electric shock or injury:

1. Use this unit only for its intended use, as described in this manual.

2. Do not use while bathing.

3. Do not place or store unit where it can fall or be pulled into water

or other liquid.

4. If unit falls into water, unplug immediately. Do not reach into water

to retrieve.

5. Never operate this unit if it has been dropped, damaged or is

working improperly. Contact an authorized Clorox technician.

6. Keep the cord away from heated surfaces.

7. Never block the air openings of the unit or place it on a soft surface

(bed or couch), where the air openings may become blocked.

8. Never drop or insert any object into any opening.

9. Do not use with a damaged or broken power cord.

10. Never store at a temperature above 140˚F.

11. This unit may be warm when in use. Do not let heated surface

touch bare skin.

General Safety

Lack of attention to safety can result in reduced efﬁciency, accident, personal injury or death. Watch for safety hazards and correct deﬁciencies promptly. Use the following safety precautions as a guide when using this machine.

1. Read the operator’s manual. Failure to do so is considered misuse

of the equipment.

2. Use the Clorox Total 360™ Electrostatic Sprayer unit only for its

intended use, as described in this manual.

3. Before operating equipment, become familiar with all caution and

warning decals afﬁxed to the equipment.

4. Do not use the Clorox Total 360™ Electrostatic Sprayer in a

hazardous location.

5. Only trained personnel familiar with the Clorox Total 360™

Electrostatic Sprayer and Clorox-approved products should be allowed to operate.

6. Do not allow personnel to operate the sprayer without proper

instruction or under the inﬂuence of alcohol or drugs.

7. Use an extension cord meeting or exceeding the speciﬁcation

detailed in the Extension Cord section.

8. Store sprayer in a cool, dry place. Do not expose to extreme

temperatures.

9. Purge liquid line before storing the unit.

10. Be aware, even when the sprayer is off, power is still supplied

to the unit when plugged into an electrical outlet.

11. Never hang unit from cord.

12. A sprayer should never be left unattended when plugged in.

13. A resettable breaker is provided on the rear of the unit. It will trip

if the unit experiences an electrical short.

14. Always turn off sprayer after each application and before unplugging.

15. Always unplug unit from outlet when not in use or when leaving it unattended.

16. Never unplug by pulling the cord or with wet hands. Always unplug by grasping the plug.

17. Do not pull or carry the sprayer by the power cord.

18. Do not crimp the cord or strain it around sharp edges, as doing so might damage the cord.

19. Do not use the Clorox Total 360™ Electrostatic Sprayer with a damaged power cord.

20. Always thoroughly inspect product before usage.

21. Contact Clorox Total 360™ Electrostatic Sprayer support center for any questions or concerns regarding the equipment: 1-800-492-9729.

Chemicals

The Clorox Total 360™ Electrostatic Sprayer can only be used with products that have been approved by Clorox. The Clorox Total 360™ Electrostatic Sprayer warranty is voided if the Clorox Total 360™ Electrostatic Sprayer is used with products that are not approved by Clorox. Be aware that many chemical liquids can be harmful if they are not used properly.

1. Always use appropriate personal protective equipment (PPE) when operating the Clorox Total 360™ Electrostatic Sprayer. Refer to product SDS for proper PPE.

2. Follow the liquid product label and SDS for proper storing, handling and disposing of any liquid products used in the Clorox Total 360™ Electrostatic Sprayer.

3. Know the length of time required by each liquid product application before allowing people and pets to return to the sprayed area.

4. Tampering with Clorox-approved products, product containers and the Clorox Total 360™ Electrostatic Sprayer in any form will void customer warranty.

5. To dispose of Clorox-approved products refer to product labels.

6. If liquid products come into contact with your skin or eyes, please refer to product label and SDS.

7. Never aim the sprayer at yourself or another person.

IMPORTANT: Safety data sheets (SDS) are available for all liquid products that have been approved for use in the Clorox Total 360™ Electrostatic Sprayer. These SDSs will inform you of any hazards and precautions of which you should be aware. All employees that use the product must be aware of and have access to the SDS. They should also be trained and aware for their safety while working with liquid products. It is the responsibility of the owner of the equipment to obtain an SDS from Clorox for each chemical used. Visit www.cloroxprofessional.com/sds for more information.

Page 7

SYSTEM COMPONENTS

The patented Clorox Total 360™ Electrostatic Sprayer was engineered with the end-user in mind. It is a durable, highly mobile and incredibly effective for electrostatic delivery.

Clorox Total 360™ Base Unit

1 Air Compressor Atomizes and propels the liquid. Runs

on 115-volt power. Includes built-in auto resetting thermal safeguard against compressor overheating.

2 Non-Marking Wheels Large wheels, for easy transport and

maneuverability, will not leave scuff marks. Do not require inﬂation.

3 Sprayer Connect Line Connect line consists of four

components: electrical line, liquid line, air line and stainless steel braided cable. The connect line connects the sprayer to the base unit.

4 Air Filter User-replaceable air ﬁlter that ﬁlters

out particles from incoming air.

5 Sprayer Holster Holds the sprayer.

6 Adjustable Handle Handle position is raised, lowered and

rotated by the two button snaps.

7 Peristaltic Pump Provides liquid up to sprayer.

8 Circuit Breaker User resettable circuit breaker and will

only trip if a short occurs in the base unit.

9 Main Power

Switch

10 1-Gallon Chemical

Containers

Powers system to a ready state.

Chemical containers (not included with equipment).

11 Extension Cord Holder Located at the rear of the unit for

extension cord storage.

12 Frame Stainless steel frame and hardware

design for long-term durability.

13 Pump Purge

Switch

14 Handle Adjust

Buttons

15 Sprayer Electrical

Disconnect

Purges product from liquid line. (press to purge)

Adjusts handle height. (squeeze to adjust)

Electrical connection for Sprayer.

Clorox Total 360™ Sprayer

1 Trigger Button 1-click functionality / operates the

sprayer/device.

2 Instrument Panel Indicates the power, sprayer and

electrostatics are on.

3 Nozzle Cover Located on the front of the sprayer.

4 Sprayer Grip Handle position for ambidextrous use.

5 Sprayer Connect Connect line consists of four components,

electrical line, liquid line, air line and stainless steel braided cable.

Nozzle

The nozzle assembly is located at the end of the sprayer. It is composed of a spring-loaded contact, external O-ring, nozzle cover, liquid tip and electrode. These are the only user-serviceable components. To access the nozzle components, unscrew the nozzle cover counterclockwise by hand. It is very important to follow all the maintenance and cleaning procedures to ensure that the sprayer will function optimally. After servicing nozzle, it is extremely important to return the nozzle to its seat position and avoid overtightening.

NOTE: As the sprayer becomes dirty from typical use, a 70% isopropyl alcohol cleaner that is manually applied is recommended on the outside surfaces. This discourages dripping from the nozzle.

| 7

Page 8

OPERATING INSTRUCTIONS

Preparing the Spray Area

1. Clean gross ﬁlth by using standard manual cleaning protocols.

2. Close the room to the general public for cleaning. Place signs or warning indicators on doors that indicate no one should enter the room.

3. Power off any sensitive electrical devices but do not unplug them.

Unit Operation/Setup

1. Choose the appropriate Clorox-approved product for cleaning, sanitizing or disinfecting.

2. Mount desired Clorox-approved product on Clorox Total 360™ Electrostatic Sprayer base and strap into place. Ensure that the bottles are positioned with the opening facing up and the opening facing the dispensing tubes.

3. Unscrew the lid on the Clorox-approved product of your choice and connect the Clorox Total 360™ Electrostatic Sprayer dispensing cap to the bottle. Be sure the cap is screwed all the way down, do not overtighten.

4. Unwrap electrical cord completely and plug Clorox Total 360™ Electrostatic Sprayer into a grounded, three-pronged socket.

5. Locate the On/Off switch on the base unit. Push the Total 360 Sprayer to the “On” position. A blue light will illuminate on both the sprayer instrument panel and unit power switch.

6. Put on appropriate personal protective equipment. See section on personal protective equipment on page 5.

7. Remove the sprayer from the unit. A blue power indicator light should be illuminated on the sprayer.

8. The system is now ready for use.

9. Priming the Clorox Total 360™ Electrostatic Sprayer: Depress into an inconspicuous corner, container or drain. Spray the Clorox Total 360™ Electrostatic Sprayer for about 20 seconds to generate a steady ﬂow of solution.

10 When spraying, a second blue indicator light will illuminate on the

sprayer instrument panel when the trigger is depressed.

NOTE: Sprayer will automatically stay on until trigger is depressed an additional time.

Sprayer Operation During Cleaning

1. Position Clorox Total 360™ Electrostatic Sprayer in a rear corner of the area.

2. Direct the nozzle at the desired surface.

3. Begin to spray. Press the sprayer button once to initiate spraying. Press once to stop ﬂow of the sprayer.

4. Follow a continuous path around the area working from high to low areas moving the sprayer in a sweeping motion until surfaces are thoroughly wet.

5. After spraying, keep the area closed to the public based on product SDSs.

6. Remove the closed sign from the door once the reentry time has expired.

Changing Clorox-Approved Products

1. Stop spraying the Clorox Total 360™ Electrostatic Sprayer.

2. Disconnect the bottle connection from the Clorox-approved product that is to be changed and remove from the sprayer. Cap the removed product if it is being stored.

3. Purging the Clorox Total 360™ Electrostatic Sprayer: Depress into an inconspicuous corner, container or drain. Spray the Clorox Total 360™ Electrostatic Sprayer for about 20 seconds to purge the system.

4. Chose the appropriate Clorox-approved product for cleaning, sanitizing or disinfecting.

5. Mount desired Clorox-approved product on Clorox Total 360™ Electrostatic Sprayer base and strap into place. Ensure that the bottles are positioned with the opening facing up and the opening facing the dispensing tubes.

6. Unscrew the lid on the Clorox-approved products of your choice and connect the Clorox Total 360™ Electrostatic Sprayer dispensing cap to the bottle. Be sure the cap is screwed all the way down, do not overtighten.

7. Priming the Clorox Total 360™ Electrostatic Sprayer: Depress into an inconspicuous corner, container or drain. Spray the Clorox Total 360™ Electrostatic Sprayer for about 20 seconds to generate a steady ﬂow of solution.

After Use and Storage

1. Stop spraying the Clorox Total 360™ Electrostatic Sprayer.

2. Disconnect the bottle connection from the Clorox-approved product that is to be changed and remove from the sprayer. Cap the removed product if it is being stored.

4. Turn off the unit. Blue indicator light on the instrument panel and base of the unit should no longer be illuminated.

5. Unplug the Clorox Total 360™ Electrostatic Sprayer from wall.

6. Wrap cord on cord holder on the Clorox Total 360 base unit.

8. Store in a safe, dry place.

Page 9

Carriage Assembly

Tube Nuts

MAINTENANCE

In order for the Clorox Total 360™ Electrostatic Sprayer to remain functional, the equipment should be cleaned on a regular basis. In addition to general cleaning of the unit there are three user-serviceable areas: air ﬁlter, sprayer nozzle and the peristaltic pump that should be maintained and serviced regularly.

3. Remove the Carriage Assembly from the Cover.

4. Remove and discard the old Tube Leader Assembly.

5. Grease the new Tube Leader Assembly with the supplied grease.

6. Replace the Tube Leader Assembly with a new one and reinstall the Carriage and Cover in reverse order being careful not to damage the Tube Leader Assembly.

Sprayer Body

The sprayer body has no serviceable parts inside. Do not open the unit shell as doing so will void the warranty on the sprayer. Contact Clorox

Total 360™ Electorstatic Sprayer support center, 1-800-492-9729, if you need to have your sprayer serviced.

Air Filter

The air ﬁlter is located on the backside of the unit and should be replaced every 1,000 hours of use. In order to remove ﬁlter, twist it counterclockwise until it pulls free from the base unit. Insert new ﬁlter by twisting in clockwise until it is hand tight. Do not overtighten.

Peristaltic Pump

Tube Leader Assembly

Cover

Nozzle

The most important thing you can do to ensure trouble-free operation of your unit is to rinse the nozzle out with clean water after every use. By cleaning your sprayer’s nozzle after each usage, you will avoid the long-term chemical buildup that eventually causes clogs, poor spray patterns and shortened life of the nozzle components. In addition to rinsing with clean water after each use, the nozzle should periodically be disassembled and cleaned. Regular maintenance should be performed. Nozzle maintenance schedule will vary, depending on how often the sprayer is used and adherence to pre- and post-spray maintenance guidelines.

It is recommended that you thoroughly read through the service outline below before performing any regular nozzle maintenance.

To Clean/Inspect the Nozzle Assembly

1. Unscrew the cap from the nozzle base. Clean any debris from or around any of the interior surfaces with warm soapy water.

2. Inspect for any damage to the liquid tip. If spray pattern was noted to be inconsistent or nontypical of a healthy symmetrical spray, remove/replace the liquid tip with an appropriate 7/16” socket wrench.

3. Inspect nozzle electrode for any signs of electrical arching, burn and/or corrosion. Gently push down on the spring-loaded contact to verify a smooth spring return. If any issues are noted, remove/ replace immediately. This is done by gently pulling on the springloaded contact with a pair of pliers. Otherwise service the springloaded contact by applying a generous amount of dielectric grease, available at any local automotive/hardware store.

4. Be sure to also thoroughly clean all interior surfaces of the nozzle cover, including the main oriﬁce. Never use a wire brush, ﬁle or sandpaper to clean any surface or oriﬁce.

1. Disconnect the clear tubing inlet and outlet by twisting the Tube Nuts counterclockwise until both tubes have separated.

2. Rotate the Cover counterclockwise and pull free from the unit.

Important: The nozzle cover should be hand-tightened. Never use pliers or other tools to tighten it, as this may cause damage. Removal of the nozzle electrode is not necessary for cleaning.

| 9

Page 10

SPECIFICATIONS TROUBLESHOOTING

Volts ~115V

Running AMPS 7.0

Startup AMPS 14.6

Frequency 60 Hz

Standard Hose Length 7 ft. (2.13m)

Dimensions 29.25 in. (.74m) H x 10.00 in. (0.25m) W

x 16.00 in. (0.40m) D

Air Line Pressure 35 psi (2.4 Bar)

Weight – Empty 44 lb. (20 kg)

Weight – Full 60 lb. (27 kg)

Shipping Weight 48 lb. (22 kg)

Flow Rate 4.05 oz./min (120ml/min)

NOTE: Do NOT use a chemical in the unit that is not a Cloroxapproved product. If you encounter the issues listed below, use the suggested troubleshooting methods. If you encounter an issue that is not addressed in this manual, contact Clorox Total 360™ Electrostatic Sprayer support center at 1-800-492-9729.

Excessive nozzle dripping

Potential Issue Corrective Action

Damage to nozzle assembly Inspect for damage and faulty

Damage to peristaltic pump tubing Replace pump tubing.

Dirty exterior sprayer surfaces Clean exterior surfaces with

parts. If present, contact the Clorox Total 360™ Electrostatic Sprayer support center service department.

solvent (70–90% alcohol).

System will not turn on or has shut off suddenly

Potential Issue Corrective Action

No power Verify the unit is plugged in and

System is not switched on Depress power switch

Compressor shuts off suddenly or won’t run while depressing the sprayer trigger

Compressor has overheated Allow the unit to sit for a

on a known working power outlet.

to illuminate.

This is a sign that the unit’s circuit breaker has tripped or that the compressor has overheated. The user should look to see if the white button (within its clear moisture cover) has popped out. If it has, the user should power off the machine, look for any physical objects that could be loose or stuck in any of the ventilation openings and clear/ dislodge. Press the button in and then attempt to power the unit back on. If the problem persists, the user should let the unit sit for 30 minutes to see if it’s an overheating issue. If the unit still refuses to restart after a cool down then they should contact technical service.

minimum of 30 minutes with the power off.

Page 11

No Spray, Erratic Spray or Weak Spray

Potential Issue Corrective Action

Out of liquid solution Inspect product container

Blockage in the nozzle or liquid tip Remove the nozzle cover and/or

Spray appears weak The user should power the unit

Damage to liquid hose or peristaltic pump tubing

for solution level and replace if empty.

liquid tip to inspect for blockages.

off, unplug from the wall and seek out a different electrical outlet to try. If unavailable, they should look to see if other devices are running on the same electrical circuit. Power those off if necessary. This could be a result of an underrated extension cord. If an extension cord is being used, remove and test the unit while using only the connected power cord. See the extension cord section for more information.

Inspect the liquid line for kinks and/or damage.

Air pressure seems low or weak

Potential Issue Corrective Action

Damage to the air hose Inspect hose for knicks, damage

Blockage in the nozzle Remove the nozzle cover and

Clogged air ﬁlter Replace air ﬁlter.

or areas where air is escaping.

inspect for blockages.

EQUIPMENT WARRANTY

Clorox warrants the original purchaser of any Clorox Total 360™ Electrostatic Sprayer that the equipment shall be free from defects material and workmanship for a period of one year after the date of delivery.

Disclaimer of Implied Warranties and Consequential Damages

The Clorox obligation under this warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, including implied warranties of merchantability and ﬁtness for a particular purpose and any liability for incidental and consequential damages with respect to the sale or use of the items warranted.

Such incidental or consequential damages shall include, but are not limited to: transportation, charges other than normal freight charges, cost of installation other than cost approved by Clorox, duty, taxes, charges for normal service or adjustments, loss of income, expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Clorox.

THIS WARRANTY SHALL NOT APPLY TO:

1. Defects, failures, damages or performance limitations caused in

2. Any Product in which any chemical other than chemical sold by

3. Normal wear and tear.

whole or in part by:

a. Power failures, surges, accidents, actions of third parties,

weather or other acts of God, or

b. The product being subjected to abuse, mishandling,

misuse, negligence, improper storage, service or operation, or unauthorized attempts to repair or alter the equipment in any way.

or on behalf of Clorox and expressly identiﬁed by Clorox for use in such product.

NO EMPLOYEE OR REPRESENTATIVE OF CLOROX IS AUTHORIZED TO CHANGE THIS WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND IS SIGNED BY A CORPORATE OFFICER OF CLOROX.

| 11

Page 12

Electrostatic Sprayer CLX1000

115VAC, 60Hz, 7.0 A

1221 Broadway Oakland, CA 94612

1-800-492-9729 www.cloroxtotal360.com NI-35818