Clore Automotive 12 Volt Power Supply & Jump Starter JNCXF, X-Force Jump-N-Carry JNCXF, X-Force Jump-N-Carry JNCXFE Product Manual
XX
--
FFoorrccee
™
12 Volt Power Supply & Jump Starter
Charge the unit for 24 hours through the built-in charger upon opening the box,
charge after every use and charge before extended storage.
Pb
CONTAINS SEALED LEAD ACID BATTERY.
BA
TTERY MUST BE RECYCLED.
Failure to follow instructions may
cause damage or explosion,
always shield eyes. Read entire
instruction manual before use.
WARNING
Warning: This product contains chemicals,
including lead, known to the State of
California to cause cancer, birth defects
and other reproductive harm.
W
ash hands after handling.
Models JNCXF and JNCXFE
Made in U.S.A.
FORCE
HIGH PERFORMANCE
JUMPSTARTING BATTERY
Congratulations! You have just purchased a world-famous Jump-N-Carry jump starter,
preferred by professionals around the world for its powerful output, exceptional service
life and rugged design. We have taken numerous measures in quality control and in our
manufacturing processes to ensure that your product arrives in top condition, and that it
will perform to your satisfaction.
In the rare event that your
Jump-N-Carry contains a damaged or missing item, does not
perform as specified, or requires warranty service, please call Technical Service at (913)
310-1050.
Save your purchase receipt, it is required for warranty service.
This unit has a sealed lead-acid battery that should be kept at full charge. Recharge
when first purchased, immediately after each use, and every three months if not used.
Failure to perform maintenance charges may cause the battery life to be reduced greatly.
Safety Information
WARNING
Read these instructions completely before using the Jump-N-Carry and save them for
future reference. Before using the Jump-N-Carry to jump start a car, truck, boat or to
power any equipment, read these instructions and the instruction manual/safety
information provided by the car, truck, boat or equipment manufacturer. Following all
manufacturers’ instructions and safety procedures will reduce the risk of accident.
Working around lead-acid batteries may be dangerous. Lead-acid batteries release
explosive gases during normal operation, charging and jump starting. Carefully read and
follow these instructions for safe use. Always follow the specific instructions in this
manual and on the Jump-N-Carry each time you jump start using the Jump-N-Carry.
All lead-acid batteries (car, truck and boat) produce hydrogen gas which may violently
explode in the presence of fire or sparks. Do not smoke, use matches or a cigarette
lighter while near batteries. Do not handle the battery while wearing vinyl clothing
because static electricity sparks are generated when vinyl clothing is rubbed. Review all
cautionary material on the Jump-N-Carry and in the engine compartment.
Always wear eye protection, appropriate protective clothing and other safety equipment
when working near lead-acid batteries. Do not touch eyes while working on or around
lead-acid batteries.
Always store clamps in their holsters, away from each other or common conductors.
Improper storage of clamps may cause the clamps to come in contact with each other,
or a common conductor, causing the battery to short circuit and generate high enough
heat to ignite most materials.
Use extreme care while working within the engine compartment, because moving parts
may cause severe injury. Read and follow all safety instructions published in the vehicle's
Owner's Manual.
While the battery in the Jump-N-Carry is a sealed unit with no free liquid acid, batteries
being jump started with the Jump-N-Carry unit likely contain liquid acids which are
hazardous if spilled.
General precautions for use:
• Someone should always be within range of your voice or close enough to come
to your aid when you work near a lead-acid battery.
• Have plenty of fresh water and soap nearby in case battery acid contacts skin,
clothing or eyes. Protective eyewear should always be worn when working near
lead-acid batteries.
• If battery acid contacts skin or clothing, wash immediately with soap and water.
If acid enters eye, immediately flood eye with cold running water for at least 10
minutes and get medical attention immediately.
• Be extra cautious to reduce risk of dropping a metal tool onto a battery. It might
spark or short circuit the battery or another electrical part that may cause
explosion.
• Remove personal metal items such as rings, bracelets, necklaces and watches
when working with a lead-acid battery. A lead-acid battery can produce a shortcircuit current high enough to weld a ring or the like to metal, causing a severe
burn.
• Use the
Jump-N-Carry for jump starting lead-acid batteries only. Do not use for
jump starting dry-cell batteries that are commonly used with home appliances.
These batteries may burst and cause injury to persons and damage to property.
• NEVER charge or jump start a frozen battery.
• To prevent arcing, NEVER allow clamps to touch together or to contact the same
piece of metal.
• Use of an attachment not recommended or sold by the manufacturer may result
in a risk of damage to the unit or injury to personnel.
• When using the power extension cord, pull on the plug and
never on the wire
when disconnecting.
• Do not recharge the Jump-N-Carry with a damaged power extension cord.
Replace it immediately.
• The
Jump-N-Carry may be used under any weather condition – rain, snow, hot
or cold temperatures.
• Do not submerge in water.
• Do not operate with flammables such as gasoline, etc.
• If the
Jump-N-Carry receives a sharp blow or is otherwise damaged in any way,
have it checked by a qualified service person. If the
Jump-N-Carry is leaking
battery acid, do not ship it. Take it to the closest battery recycler in your area.
• Do not disassemble the Jump-N-Carry. Have it checked by a qualified ser
vice
person.
• The
Jump-N-Carry should never be left in a completely discharged state for any
period of time. Damage to the battery could be permanent, with poor
performance as a r
esult. When not in use, r
echar
ge ever
y three (3) months.
• Always store, use and char
ge the
Jump-N-Car
r
y
in an ar
ea wher
e childr
en
cannot get to the unit.
Features
• The Jump-N-Carry provides plenty of power for starting vehicles – more than
enough to start most cars.
• The
Jump-N-Carry will power most 12 Vdc accessories equipped with a male
12 Volt plug. The DC outlet features automatic overload protection.
• The unit features a test switch and battery status gauge, which provides an
approximate indicator of the battery’s state of charge.
• The
Jump-N-Carry features convenient side-mounted holsters with cable tracks
for easy cable and clamp management. Always re-wrap cables and re-holster the
clamps, reinstalling the Grip Guards™ in the process, after each use.
• The
Jump-N-Carry contains the latest technology with its 12 Volt sealed,
non-spillable battery and may be stored in any position.
Recharging
Note: Upon initial purchase, your Jump-N-Carry should be charged for a minimum of
24 hours.
There are two ways to charge your Jump-N-Carry. The recommended method is
recharging using AC power, with an extension cord (see note below) connected to the
built-in charger. An alternative method is through the DC power outlet using the provided
12 Volt Male-Male Extension Cord.
Charging using the built-in charger (recommended method). With this method, an
extension cord (a standard extension cord, not included, for model JNCXF; the provided
2-pin extension cord for model JNCXFE) is connected to the
Jump-N-Carrythr
ough the
built-in charger located on the front of the unit.
1. Connect the female end of the appropriate extension cord to the charger plug on
the front of the unit.
2. Connect the male end to the extension cor
d to the AC outlet.
3. Charge the unit based on the suggested recharge times shown in the following
table.
Battery Status Gauge
Press and hold the red test button to display the battery status on the gauge.
• The Green shaded area indicates the unit is capable of jump starting.
• The
Yellow shaded area indicates the unit needs to be recharged.
• The Red shaded area indicates the unit must be recharged immediately.
You can also get a quick check of the vehicle’s charging system by depressing the red
test button while connected to a running vehicle and observing the gauge.
SUGGESTED AC RECHARGE TIMES
After a single jump start: 1 hour
After multiple jump starts: 12 hours or overnight
After using as portable power: 24-36 hours
Charging using the supplied 12 Volt Male-Male Extension Cord. This alternative charging
method may be used when access to an AC outlet is unavailable.
1. Start the vehicle’s engine.
2. Plug one end of the 12 Volt Male-Male Extension Cord into the Jump-N-Carry
12 Volt outlet and the other end into the vehicle’s 12 Volt power port.
3. Charge the unit based on the suggested recharge times shown in the following
table.
SUGGESTED 12 VOLT RECHARGE TIMES
After jump starting: 20 minuntes
After using as portable power: 2 hours
After high discharge conditions: 5 hours
Note: DO NOT OVERCHARGE! You must frequently monitor the charging process to
ensure the unit is not overcharged. Overcharging will damage your Jump-N-Carry.
Jump Starting Instructions
Note: For optimum performance, do not store your Jump-N-Carry below 50° when
using as a jump starter. NEVER charge or jump start a frozen battery.
1. Use in a well ventilated area.
2. Shield eyes. Always wear protective eyewear when working near batteries.
3. Review this instruction manual and the instruction/safety manual provided by the
manufacturer of the vehicle being jump started.
4. Turn ignition off before making cable connections.
5. Clamp the positive (red +) clamp to the positive terminal on the vehicle battery
(for negative ground system), or an alternate vehicle starting point as
recommended by vehicle manufacturer.
6. Clamp the negative (black –) clamp to the vehicle ground (non-moving metal part,
such as the vehicle frame).
7. Make sure the cables are not in the path of moving engine parts (belts, fans, etc.).
8. Stay clear of batteries while jump starting.
9. Start the vehicle (turn on the vehicle ignition).
Note: If the vehicle doesn’t start within 6 seconds, let the Jump-N-Carry cool
for 3 minutes before attempting to start the vehicle again or you may damage the
Jump-N-Carry.
10. When the vehicle is started, disconnect the negative (–) battery clamp from the
vehicle frame and return it to its holster.
11. Disconnect the positive (+) clamp and return it to it’s holster.
12 Volt DC Power
Your Jump-N-Carry is an essential tool for all who replace automobile batteries.
Most vehicles have electronic components with memory, such as alarm systems,
computers, radios, phones, etc. and when the vehicle’s battery is replaced, the memory
is lost. However, if the Male-Male Extension Cord is connected from the
Jump-N-Carry
to the 12 Volt outlet on the vehicle, the memories can be saved.
Note: To use the Jump-N-Carry for this purpose, the chosen outlet must be live when
the vehicle is turned OFF. On some vehicles, 12 Volt outlets are deactivated when the
vehicle is turned OFF.
Your Jump-N-Carry is also a portable power source for all 12 Vdc accessories
equipped with a male 12 Volt plug. The DC outlet on the Jump-N-Carry has automatic
overload protection.
When your
Jump-N-Carry is used with a DC to AC power inverter, it can operate
appliances normally powered by 120 Vac or 220 Vac. Recommended inverter for the
portable power source is 400 watts maximum. For more information, contact your
nearest
Jump-N-Carry dealer.
Performance and Temperature
Performance of your Jump-N-Carry will depend upon several factors:
• A good, solid connection between the Jump-N-Carry clamps and the battery
and ground connections are a must. Moving the clamps back and forth while
connecting to the battery will help create a better connection.
• Clean connections between your vehicle or equipment battery and its terminals are
very important. For an optimal connection, corrosion (soft grayish-white build-up)
on battery terminals must be removed. With the ignition turned off, disconnect the
battery cables and clean the terminals and battery posts with a baking soda
solution.
• All batteries are affected by temperature changes, and the small, lightweight
battery in the
Jump-N-Carry is more sensitive to storage temperature than a
standard automotive battery. Temperatures above 20ºC decrease amperage output.
The ideal storage environment is room temperature, or 68ºF.
Troubleshooting/FAQs
Q. What should I do if the Jump-N-Carry will not hold a charge?
A. Load test the battery. Charge battery 24 hours before load testing. Connect a load
tester (available at your local auto parts store) to the
Jump-N-Carry clamps to
check battery amperage. Depending on the model of load tester, your load testing
procedure may vary. A generic load test would bring the voltage down to 9.0 volts
and result in an amp reading of 70 amps for 6 seconds. Repeat this load test every
10 minutes for a total of three tests. If the amperage has dropped below 50 amps
on the last test, suspect a bad or weak battery.
Q. What is the ideal use for the
Jump-N-Carry?
A. The Jump-N-Carry performs strongly when a vehicle’s battery needs an extra
boost because a light or radio was left on, or when a vehicle has been sitting for a
long period of time. The Jump-N-Carry will start vehicles without any other
batteries present, but the primary use is for an extra boost.
Q. Will the
Jump-N-Carry start every vehicle?
A. No. In addition to a dead battery, a car may have other mechanical problems that
would prevent the
Jump-N-Carry from starting the vehicle.
Q. How often should I recharge the Jump-N-Carry?
A. To maximize battery life, charging after every use is recommended. The
Jump-N-Carry should not be left in a discharged state. The battery in the
Jump-N-Carry has no memory problems and should not be treated as a
rechargeable tool (cordless drills, camcorders, etc.).
Q. How many jump starts can I get from the
Jump-N-Carry before recharging?
A. A large number of factors affect this answer, including the following: the length of
time for each jump start, the charge level of the original battery, the length of time
between jump starts, the temperature of the vehicles being jump started (winter
cold makes for difficult starting), the size of the engines (4-cycl, 6-cycl, 8-cycl, etc.),
the mechanical condition of the engine and starter, and more. These factors must
all be weighed on an individual basis before an accurate answer can be given. It’s
feasible to get 10-30 starts (individual’s results will differ) from a single charge, but
this violates the rule of immediate charging after every use.
Q. After jump starting, can I leave the unit hooked to the battery to recharge the
Jump-N-Carry while the engine is running?
A. No. Attempting to recharge the
Jump-N-Carry by this method is not
recommended. Vehicle alternators output anywhere from 25-125 amps. This
charging rate greatly exceeds the recommended recharging rate for
Jump-N-Carry. Charging by this method will result in overcharging the
Jump-N-Carry battery, and may void the product warranty.
Q. What accessories can be used in the optional 12 volt outlet?
A. Any accessory up to 12 amps can be powered by the
Jump-N-Carry. This unit is
equipped with an automatic reset circuit breaker, should the current exceed 12
amps. At the same time, this limits any recharge current through the 12-volt outlet
to 12 amps. One can power almost any 12-volt tool or accessor
y (examples:
impact wrenches, fans, radios, cellular phones, navigation equipment, camcor
ders,
emergency power, tr
olling motors, coolers, small r
efrigerators, etc.).
Q. Can the Jump-N-Carry battery be replaced?
A. Yes, call Technical Service at (913) 310-1050 (U.S.).
Q. Can the
Jump-N-Carry be recycled?
A. Yes, the environment was one of our main concerns in the development and design
of the
Jump-N-Carry. Most battery outlets can dispose of this product at its life's
end. In fact, your
Jump-N-Carry contains a sealed, non-spillable lead acid battery
and
proper disposal is required by law. See Battery Removal and Disposal
Instructions.
Q. I have a regular 10 amp battery charger, can I use it to recharge the
Jump-N-Carry?
A. No, only the methods reviewed in the “Recharging” section should be used.
Q. Is the Jump-N-Carry goof proof?
A. No, jump starting instructions must be followed. Read and understand all safety
and operating instructions in this manual and those found in the owner’s manual of
any vehicle being jump started before using your
Jump-N-Carry.
Storage
The Jump-N-Carry may be stored virtually anywhere, and in any position. However,
take precautions to ensure that the positive and negative clamps do not come into
contact with each other or a common metal surface. We recommend storing the
Jump-N-Carry in the box in which it was originally received. Always be sure to re-wrap
cables and re-holster clamps after each use and prior to extended storage.
Testing The Battery
After fully charging the battery (see “Recharging” section), apply a 100 amp load to the
unit for a period of 6 seconds, while monitoring the battery voltage. The battery is good
if the voltage is 9.5 Vdc or higher.
The battery inside this product is a sealed lead-acid battery. It is required by law to be
removed and recycled or disposed of properly. While there are federal regulations that
must be complied with throughout the United States, your individual state or local
governments may have additional regulations to be followed.
When the battery in this product is in need of replacement, remove it according to the
instructions provided below and take it to your local recycling center for proper recycling
or disposal. If you don’t have a local recycling center that handles sealed lead-acid
batteries, contact your local environmental agency for instructions.
Removal instructions:
Begin by making sure that both clamps are securely placed in a position that ensures
they will not come into contact with each other.
1. Lay the Jump-N-Carry down on its front. On the back of the unit, locate the
screws that hold the back panel in position.
2. Remove the screws, then lift off the back panel.
3. On the top of the battery are two terminals, each with wires connected to them.
Disconnect these wires from the battery by removing the bolts that hold them to
the battery terminals. To prevent accidental arcing, be careful not to touch both
battery terminals with the tools being used to remove the bolts.
4. Lift the battery(ies) out of the case.
Battery Replacement and Disposal
Pb
This unit contains a sealed non-spillable lead-acid battery.
This battery must be recycled.
Consult your state or local
government concerning regulations for proper disposal.
Jump-N-Carry Limited Warranty
Clore Automotive warrants this product to be free from defects in material or
workmanship for a period of one year from the date of original end user purchase.
This warranty extends to each person who acquires lawful ownership within one year of
the original retail purchase, but is void if the product has been abused, altered, misused
or improperly packaged and damaged when returned for repair.
This warranty applies to the product only and does not apply to any accessory items
included with the product which are subject to wear from usage; the replacement or
repair of these items shall be at the expense of the owner.
THE TERMS OF THE CLORE AUTOMOTIVE LIMITED WARRANTY CONSTITUTE THE
BUYER’S SOLE AND EXCLUSIVE REMEDY. THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN
DURATION TO THIS EXPRESS WARRANTY. AFTER 1 YEAR FROM DATE OF PURCHASE,
ALL RISK OF LOSS FROM WHATEVER REASON SHALL BE PUT UPON THE PURCHASER.
CLORE AUTOMOTIVE SHALL NOT BE LIABLE FOR INCIDENTAL AND CONSEQUENTIAL
DAMAGES UNDER ANY CIRCUMSTANCES: CLORE AUTOMOTIVE’S LIABILITY, IF ANY,
SHALL NEVER EXCEED THE PURCHASE PRICE OF THIS PRODUCT REGARDLESS OF
WHETHER LIABILITY IS PREDICATED UPON BREACH OF WARRANTY (EXPRESS OR
IMPLIED), NEGLIGENCE, STRICT TORT OR ANY OTHER THEORY.
Some states do not permit the limitation of warranties or limitation of consequential or
incidental damages, so the above disclaimer and limitation may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
For Warranty or Service
If this product fails within the first 30 days after retail purchase due to a defect in
material or workmanship, return it to your place of purchase for an exchange.
From day 31 to day 365 after retail purchase, contact Clore Automotive Technical
Service at the number below for warranty service. A valid, dated sales receipt is
required to obtain service under this warranty.
For best service and to receive periodic product updates, follow the instructions below
to register your purchase:
Please visit: www.cloreregistration.com
Click on the
Jump-N-Carry logo
Complete the information in the web form and click “submit”
It’s that easy!
For answers to questions concerning use, out-of-warranty service, or warranty/service
information on this or other Clore Automotive products, contact:
Clore Automotive Technical Service
800.328.2921
913.310.1050
www.cloreautomotive.com
Loading...