Page 1
FAMILY PRACTICE &
CABINET STYLE TABLES
MODELS: 8834, 8844, 8870 & 8890
ASSEMBLY INSTRUCTIONS
Page 2
ASSEMBLY INSTRUCTIONS FOR FAMILY PRACTICE EXAM TABLES
MODELS: 8834, 8844, 8870 & 8890
MAXIMUM WEIGHT CAPACITY 400 LBS
Thank you for counting on Clinton to meet your medical
equipment needs by purchasing this fine equipment. All
Clinton equipment is designed and manufactured to provide
years of dependable service because we want you as a
customer now and in the future. Below are easy to follow
instructions on how to properly assemble your equipment.
Please contact us at 800-441-9131 if you experience any
difficulty with the assembly or have questions.
MODEL 8870
MODEL 8834 same as 8870 without stirrups
F
B
G
E
MODEL 8890
MODEL 8844 same as 8890 without stirrups
A
H
D
C
INTENDED USE. Clinton Family Practice and Space Saver
models 8834, 8844, 8870 and 8890 are specifically designed
and engineered for medical examinations use only. Persons
using the table should be observed by trained medical personnel
while on the table and getting off the table. Never leave anyone
unattended on the table. Combination of weight and force
exerted on the table is not to exceed a total of 400 lbs. Using
this equipment for unintended purposes could result in
damage to the equipment and serious injury.
CAUTION: Never sit on the pull-out leg rest or the head
end of the table. The pull-out leg rest and the head end of
the table are not engineered to support full body weight
or excessive weight/force combination. Sitting on the leg
rest and/or head end of the table could result in damage
to the table and/or serious injury.
WARNING: Periodically check that both of the pull-out, step
stool's rubber feet are in good condition, and rest on the
floor when in use. If not, serious damage to the table, as well
as, serious injury could occur to persons using the step stool
which could slip while in use.
Contents
A. Adjustable Padded Backrest
B. Padded seat
C. Base
D. Dual Entry Storage
E. Drawer Storage
F. Pull-Out Stirrups (8870 only)
G. Laminate Pull-Out
H. Paper Dispenser
Hardware for Table
(4) 1" Hex Head Bolts
(8) 3/4" Pan Head Screws
(4) 7/16" Kep® Lock Nuts
(4) 1/4" washers
Tools Required
•
Phillips Screwdriver/Screw Gun
• Socket
Time Required
•
Wrench
15–20 Minutes
A
B
H
D
C
G
I
F
Contents
A. Adjustable Padded
Backrest
B. Padded seat
C. Base
E
J
D. Dual Entry Storage
E. Drawer Storage
F. Pull-Out Stirrups
G. Laminate Pull-Out
H. Paper Dispenser
I. Pull-Out Step Stool
J. Rubber Feet
Hardware for Table
(4) 1" Hex Head Bolts
(8) 3/4" Pan Head Screws
(4) 7/16" Kep® Lock Nuts
(4) 1/4" washers
Tools Required
•
Phillips Screwdriver/Screw Gun
• Socket
Time Required
•
Wrench
15–20 Minutes
Page 3
Attach backrest to the table by lining up holes
1
(4) four Kep® Lock Nuts and a 7/16" socket wrench.
2
in hinge with the 4 protruding bolts in the
center table brace. Secure the backrest with the
Extend the pneumatic cylinder about half way by
holding the apparatus with one hand and pressing
down on one of the levers with the other.
4
5
Locate the seat brackets and place padded seat
on top of the brackets.
BRACKETS
Secure the seat to the seat brackets using (4)
four 1" hex head bolts and 1/4" washers.
DO NOT TIGHTEN ALL THE WAY.
3
Secure the pneumatic cylinder’s bracket to
the backrest with the (8) eight 3/4" pan head
screws.
Check the alignment of the seat in relationship
6
When satisfied with the alignment, tighten the bolts from
step 5 all the way, making sure the seat is in a fixed and
secure position.
to the backrest, slide the seat side to side to
adjust if necessary.
Page 4
Limited Warranty
ON FRAME &
ELECTRICAL
COMPONENTS
For protection during shipping, the drawer pulls
7 8
proper position.
are mounted inside the drawers. Unscrew the
mounting screws, and move the pulls to the
the brackets.
PAPER DISPENSER.
Place rod through paper tube and place onto
brackets. Metal caps should be on the outside of
FOR SAFETY PURPOSES, TAKE TIME TO CHECK ALL FASTENERS TO INSURE THAT THEY
ARE SECURELY TIGHTENED AND THAT THE EQUIPMENT HAS BEEN PROPERLY
ASSEMBLED ACCORDING TO THESE INSTRUCTIONS.
Warranty
Clinton Industries warrants manufactured products to be free of defects in materials, workmanship or design under normal
use for five years on all products, from the date of purchase. This warranty does not include damage resulting
from accident, abuse or misuse, alteration, or negligence of the product and expressly excludes normal wear
of parts (including but not limited to vinyl). Contact Clinton for full warranty details.
Limited
Warranty
Care & Cleaning
Clinton products are built to be durable. With proper care, your Clinton equipment will provide years of superior looks and
performance. Before using any cleaning agents, try them on a small inconspicuous area to insure that they will not harm the
any surface. Damage from cleaning is not covered under the warranty.
Do not use alcohol based cleaning agents. Periodically check that all fasteners are secure and operating properly.
© Copyright 2015, Clinton Industries, Inc. All rights reserved.
800-441-9131 • 717-848-3519
Toll-Free Fax 866-522-1233 • Fax 717-843-5871
www.clinton-ind.com
CLI-MA-008
Loading...