ClimbTech TLA075 Instruction Manual

IMPORTANT!!!

ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS.
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD BE FAMILIAR
WITH PERTINENT REGULATIONS GOVERNING THIS EQUIPMENT. ALL INDIVIDUALS WHO USE
THIS PRODUCT MUST BE PROPERLY INSTRUCTED ON HOW TO USE THIS DEVICE.

Inspection:

Ocial periodic inspection must be made at least annually. The inspection must be
performed by a qualied person other than the intended user. If severe weather or
conditions exist then inspections must be carried out more frequently. All inspection
results must be logged in the space provided above.

1. Inspect unit for visible signs of damage or wear that could aect operation. For
example: kinked or frayed cables.

2. Make sure all labeling is axed to the unit.

3. Check toggle bar and end termination operate smoothly with no metal burrs.

4. When reusing a previously drilled hole, inspect for for debris or wallowing.

5. Record inspection results in the space provide above.

Part Number Comments

Inspector Name

*If any damage that could aect the strength or operation of the device, or
unsafe conditions are found, proper disposal is required. The anchor connector
must be rendered unusable and then properly discarded.

V1.2

Toggle Bolt Anchor

5,000-lbs / 22kN

Model: TLA

075N

Assembled in the USA

INSPECTION AND MAINTAINANCE LOG

MODEL NUMBER:

DATE OF MANUFACTURE:

Product Warranty, Limited Remedy and Limitation of Liability

WARRANTY: THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTIES
OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Equipment oered by ClimbTech is

warranted against factory defects in workmanship and materials for a
period of one year from date of purchase.

LIMITED REMEDY: Upon notice in writing, ClimbTech will repair or
replace all defective items at ClimbTech’s sole discretion. ClimbTech
reserves the right to require that the defective item be returned to its
plant for inspection before determining the appropriate course action.
Warranty does not cover equipment damage resulting from wear, abuse,
damage in transit, failure to maintain the product or other damage
beyond the control of ClimbTech. ClimbTech shall be the sole judge of
product condition and warranty options. This warranty applies only to
original purchaser and is the only warranty applicable to this product.
Please contact ClimbTech technical service department for assistance.

LIMITATION OF LIABILITY: IN NO EVENT WILL CLIMBTECH BE LIABLE
FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES INCLUDING, BUT NOT LIMITED TO LOSS OF PROFITS, IN
ANY WAY RELATED TO THE PRODUCTS REGARDLESS OF THE LEGAL
THEORY ASSERTED.

Read This Instruction Manual Carefully Before Using This Equipment.

User Instructions must always be available to the user and are not to be removed except by the user of this equipment. For proper use, see
supervisor, User Instructions, or contact the manufacturer.

Compliant fall protection and emergency rescue systems help prevent serious injury during fall arrest. Users and purchasers of this equip­ment must read and understand the User Instructions provided for correct use and care of this product. All users of this equipment must
understand the instructions, operation, limitations and consequences of improper use of this equipment and be properly trained prior to
use per OSHA 29 CFR 1910.66 and 1926.503 or applicable local standards. Misuse or failure to follow warnings and instructions may result

in serious personal injury or death.

Purpose

The

SWY

100

N

is an anchorage connector designed to function as an interface between the anchorage and a fall protection, work positioning,
rope access, or rescue system for the purpose of coupling the system to the anchorage. Any references to “anchorage connector” in this manual
include, and apply to, the

SWY

100

N

.

Use Instructions

1. Before using a personal fall arrest system, user must be trained in accordance with the requirements of OSHA 29 CFR

1910.66 in the safe use of the system and its components.

2. Use only with ANSI/OSHA compliant personal fall arrest or restraint systems. The anchorage must have the strength capable
of supporting a static load, applied in the directions permitted by the system, of at least 10,000-lbf (44kN) in the absence of
certication.

3. Use of this product must be approved by an Engineer or other qualied person to be compatible with any and all structural
& operational characteristics of the selected installation location and system to be connected to this anchor. Improper use

may result in serious personal injury or death.

4. The anchorage connector must be inspected prior to each use for wear, damage, and other deterioration. If defective
components are found the anchor connector must be immediately removed from service, in accordance with the requirments

of OSHA 29 CFR 1910.66 and 1926.502.

5. The complete fall protection system must be planned (including all components, calculating fall clearance, and swing fall)
before using.

6. A rescue plan, and the means at hand to implement it, must be in place that provides the prompt rescue of users in the
event of a fall, or assures that users are able to rescue themselves.

7. After a fall occurs, anchorage connector must be removed from service and destroyed immediately.

Use Limitations

1. The anchorage connector is designed for up to two users at one time as part of a exible horizontal lifeline system with a
capacity up to 310 lbs (140kg) per user including clothing, tools, etc. (See anchorage requirements in the User Instructions for
the exible horizontal lifeline system). When used as a direct anchorage connection, the anchorage connector has a single
user max capacity of 400 lbs including clothing, tools, etc.

2. The

anchorage connector

may be pulled in any direction shown in the LOADING CONDITIONS DIAGRAM.

3.

The Anchorage connector

is designed to be used in temperatures ranging from -40ºF to +130ºF (-40°C to +54°C).

4. Do not expose the

anchorage connector

to chemicals or harsh solutions which may have a harmful eect.

5. Do not alter or modify this product in anyway.

6. Caution must be taken when using any component of a fall protection, work positioning, rope access, or rescue system near
moving machinery, electrical hazards, sharp edges, or abrasive surfaces, as contact may cause equipment failure, personal
injury, or death.

7. Do not use/install equipment without proper training by a “competent person” as defined by OSHA 29 CFR 1926.32(f).

8. Do not remove the labeling from this product.

9. Additional requirements and limitations may apply depending on anchorage type and fastening option utilized for
installation. All placements must be approved by an engineer or other qualied person. Improper use may result in serious

personal injury or death.

COMPATIBILITY LIMITATIONS

All anchor connectors must only be coupled to compatible connectors. OSHA 29 CFR 1926.502 prohibits snaphooks from being engaged to
certain objects unless two requirements are met: it must be a locking type snaphook, and it must be “designed for” making such a connec­tion. “Designed for” means that the manufacturer of the snaphook specifically designed the snaphook to be used to connect to the equip­ment listed. The following connections must be avoided, because they can result in rollout* when a nonlocking snaphook is used:

• Direct connection of a snaphook to horizontal lifeline.

• Two (or more) snaphooks connected to one D-ring.

• Two snaphooks connected to each other.

• A snaphook connected back on its integral lanyard.

• A snaphook connected to a webbing loop or webbing lanyard.

• Improper dimensions of the D-ring, rebar, or other connection point in relation to the snaphook dimensions that would allow the
snaphook keeper to be depressed by a turning motion of the snaphook.

*Rollout: A process by which a snaphook or carabiner unintentionally disengages from another connector or object to which it is coupled.
(ANSI Z359.1-2007)

MAINTAINANCE, CLEANING AND STORAGE

Cleaning periodically will prolong the life and proper functioning of the product. The frequency of cleaning should be determined by inspec­tion and by severity of the environment. Clean with compressed air and/or a sti brush using plain water or a mild soap and water solution. Do
not use any corrosive chemicals that could damage the product. Wipe all surfaces with a clean dry cloth and hang to dry, or use compressed air.
When not in use, store anchorage connectors in a cool, dry, clean environment, out of direct sunlight and free of corrosive or other degrading
elements.

WARNING

ClimbTech, LLC. / 7303 Burleson Rd. Suite 901 Austin, TX 78744 / 1(888)206-1318 / www.climbtech.com

All products subjected to fall arresting forces should be removed
from service immediately!

DECK/FLOOR/GROUND LEVEL

WORK SURFACE

(ANCHOR POINT)

MINIMUM CLEARANCE 3ft (1m)

WARNING!!! SWING FALLS CAN OCCUR WHEN THE WORKIER IS NOT DIRECTLY UNDER ANCHOR POINT.

Free fall distance (limit) must
not exceed 6’ ft (1.8 m).

The Hollow Core
concrete must be
5000-psi or higher and
fully cured. Installation
location to be approved
by a qualied person.

Performance:

Static tensile strength: 5000-lbf

(22kN) minimum.
Maximum capacity: one worker with
max weight of 310-lbs when used as
a single point anchorage connector
for personal fall arrest or restraint

Dimensions:

Weight: 0.4-lbs (.18kg)
Length: 11.5” (293mm)
Diameter: 0.75” (20mm)

Regulatory compliance

ANSI Z359.1-2007, ANSI Z359.7-2011 and OSHA

1926.502 CE 0321 / EN 795:1996 (+A1:2000) Class B

Component Materials:

Main Cable: Aircraft Cable. Ball Shank: Stainless Steel. Toggle Bar: Stainless Steel. Hole
Plug: Aluminum. Spring: Zinc Plated Steel. Swage: Zinc Plated Copper. Activator Wire:
Aircraft Cable. Loop Cover: Polyurethane.

WORK SURFACE

May be used as a anchoring point for a leading
edge restraint system. (Examples are of optional
anchoring point locations. The use of two anchors
is for illustration purposes only and not required
for leading edge restraint systems unless other­wise specied by the manufacturer.

OPTIONAL

(ANCHOR POINTS)

Toggle Bar

Spring

Swage Anchor Loop

1.5” (38mm)

3.0” (76mm)

10.75” (273mm)

Main Cable

2” (50.8mm)

Activator Wire

Hole Plug

.75”ø (20mm)

Ball Shank

INSTALLATION:

(1) (2) (3)

(4) (5) (6)

Drill
3/4”

(20mm)

Flip

Toggle

To

Verti cal
Position

Insert

In

Hole

Push

Down

Pull

Up

INSTALLATION IN HOLLOW CORE CONCRETE:

(1) Drill a 3/4” (20mm) hole in center of the hollow channel in the
hollow core concrete. The hollow core concrete must be at least
5,000-psi (34.5 MPa) concrete with a web thickness of 1-3/4”
(44.45mm) thick. Works with 6“ hollow core or larger.
(2) Never drill any hole closer than 6” (152mm) to any edge or
corner.
(3) Always inspect the hole carefully when reusing a previously
drilled hole.
(4) Make sure the toggle bar is fully seated and in lock position.
(See activation indicator illistration)
(5) The hole plug should be full seated in the drilled hole in the
concrete.

INSTALLATION IN STEEL:

(1) Drill a 3/4” (20mm) hole in the steel ange. Steel ange must
be at least 1/4” (64mm) thick.
(2) Never drill a hole closer than 1-1/2” (38mm) to any edge or
corner.
(3) When reusing a previously drilled hold always inspect the hole
carefully.
(4) Make sure the toggle bar is fully seated and in lock position.
(See activation indicator illistration)

Location of installation of the toggle anchor must be approved by a

Engineer or other qualied person to be compatible with any and all

structural & operational characteristics of the selected installation location.

WARNING!!!

LOCKED

POSITION

OPEN

POSITION

BLACK RED

BLACK RED

Activator

Wire

Indicator

OPEN

BLACK RED

Activator

Wire

Indicator

NOT

SAFE

Activator

Wire

Indicator

ACTIVATION INDICATOR:

OPEN

OPEN

1-3/4”
min web
thickness

V1.1

REMOVAL INSTRUCTIONS:

(1) When removing anchor, place your thumb inside the anchor loop

and your rst two ngers around the hole plug. Squeeze ngers and

thumb together till the trigger and spring fully compress.

(2) While squeezing the hole plug and loop pull the anchor out of the

hole.

DO NOT REMOVE
WARNING LABEL!

DO

NOT REMOV

E

St

ainle

ss

S

t

e

el, Aluminum

, Zinc

Plate

d Copper, 7

x1

9

A

ir

c

r

a

ft

Ca

bl

e

Compli

a

nc

e:

O

SHA 1926

.50

2 &

19

10

.66 / ANSI Z35

9

.1

CE 032

1 / EN

7

95

:

19

9

6

(+

A

1:

20

0

0

) Cla

s

s B

W

ARNI

N

G!!!

AL

L

P

ER

SO

N

S

U

S

IN

G

TH

I

S E

Q

UIP

M

E

N

T MU

S

T

R

EAD AN

D

UN

D

ER

ST

A

N

D AL

L

I

N

STR

UC

T

I

O

N

S

.

FAILURE

T

O

DO

SO

MAY R

ES

U

LT IN

SE

R

I

O

U

S

I

N

J

U

R

Y

O

R

DEATH

. USER

S

SHO

U

L

D

B

E F

A

M

I

L

I

A

R

W

I

T

H P

ER

TIN

E

N

T R

EG

U

LATIO

N

S GO

V

ER

N

I

N

G

THIS

E

Q

U

I

P

M

E

N

T

. AL

L

IN

DI

V

I

D

U

AL

S

W

HO USE

TH

I

S P

R

O

D

U

CT MU

S

T B

E

P

R

O

P

E

R

LY

IN

S

T

R

U

C

TED O

N

HO

W

TO USE

TH

I

S

D

EV

I

C

E

.

RTL-X

X

X

/ MM/Y

Y

Y

Y

DO NOT REMOVE

Toggle Bolt Anchor

Model: TLA075N

1-(888)-206-1318

Stainless Steel, Aluminum, Zinc Plated Copper, 7x19 Aircraft Cable

Compliance: OSHA 1926.502 & 1910.66 / ANSI Z359.1, ANSI Z359.7

CE 0321 / EN 795:1996 (+A1:2000) Class B

WARNING!!!

ALL PERSONS USING THIS EQUIPMENT MUST READ AND UNDERSTAND ALL INSTRUCTIONS.
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH. USERS SHOULD BE FAMILIAR
WITH PERTINENT REGULATIONS GOVERNING THIS EQUIPMENT. ALL INDIVIDUALS WHO USE
THIS PRODUCT MUST BE PROPERLY INSTRUCTED ON HOW TO USE THIS DEVICE.

RTL-xxx / mm/yyyy

INSPECT BEFORE USE

Max Capacity 310-lbs