Climax Technology Co WTRVS Users manual

Voice Reach Talking Pendant ((WWTTRRVVSS))

I. Identifying the Parts

11.. AAccttiivvee//PPeennddaanntt BBuuttttoonn

 Press the Active Button once will activate the Control Panel, causing it to dial

emergency call or alarm. Once the button is pressed, the Green LED lights on for 3
sec and then becomes flashing to indicate alarm signal transmission to the Control
Panel is in progress. During signal transmission, the WTRVS will emit continuous
beeps.

 When the Control Panel receives the signal from WTRVS, its red light will go on. It

will then dial the Central Monitoring Station and wait for command. Once the Central
Monitoring Station acknowledges the signal, a remote two-way voice communication
channel will be opened with the WTRVS.

 When there is an incoming phone call, you can press the Active Button to answer it.

If the two way communication is enabled, WTRVS will stop emitting beeps. WTRVS
will open a remote two-way voice communication for 30 minutes.

 To terminate both the reporting and the two-way communication, press and hold the

Active Button for 8 sec.

22.. DDuuaall CCoolloouurr RReedd && GGrreeeenn LLEEDD

 LED OFF: In Standby Mode

 RED LED ON: Registering WTRVS to the Control Panel

 RED & GREEN LED FLASH: Transmitting signal to the Control Panel

 GREEN LED ON: Receives learning signal from the Control Panel

33.. SSppeeaakkeerr

44.. LLaannyyaarrdd LLoooopp

55.. MMiiccrroopphhoonnee

66.. CCRR22 33VV LLiitthhiiuumm BBaatttteerryy

77.. LLooww BBaatttteerryy DDeetteeccttiioonn BBuuttttoonn

 Press the Low Battery Detection button to test WTRVS’s battery status while

WTRVS is in the stand by mode. If WTRVS emits 3 short beeps after pressing the
button, it indicates that WTRVS is in the low battery status. If not, it means WTRVS’s
voltage is in the normal state.

 If WTRVS is detected in the low battery status, when you press WTRVS to dial an

emergency call or alarm, the Red LED will go on for 3 seconds and WTRVS will emit
continuous raipd beeps.

 You are not allowed to test the battery status during two-way communication mode

or the period of triggering the emergency alarm.

1

II. Learn In WTRVS

For Medical Panel (CTC-1041RV/CTC-1052RV):

Step 1. Please refer to the Control Panel manual and put the Control Panel into Learning

Mode.

Step 2. Press & hold WTRVS ACTIVE/PENDANT button for 5 seconds. The WTRVS’s

Green LED will turn to Red. When hearing a long beep, release the WTRVS button.
The WTRVS is now in the learn mode.

Step 3. Press and hold the reset button on the Control Panel for 20 seconds and meanwhile

the WTRVS’s LED will turn from RED, then blink green to steady green. When you
hear two beeps and then one long beep emitted from the Control Panel, release the
RESET button from the Control Panel. The learning process now is successful.

<<NNOOTTEE>>

Step 4. To check if the WTRVS is successfully learnt in, press the WTRVS ACTIVE button. If

Step 5. Exit the Control Panel out of Learning Mode. The Learning process is now complete.

<<NNOOTTEE>>

 It is prohibited to learn-in another or the same WTRVS twice, unless the previously

learnt WTRVS is removed first.

you hear 6 continuous beeps from WTRVS and meanwhile the Control Panel respond
two shorts beeps respectively, it indicates that the WTRVS is successfully learnt in. If
you don’t hear any corresponding beep from Control Panel after pressing the WTRVS
ACTIVE button, it indicates that the learning process fails. Turn the Pedant off and
repeat the steps mentioned above until you hear the Control Panel’s corresponding

beeps.

 Re-learning is only required if the WTRVS is removed, but not required after battery

replacement. To remove WTRV, you have to remove it from the Control Panel first and
then reset it to factory default.

FFOORR AALLAARRMM PPAANNEELL OORR CCTTCC--11006688RRVV:

Step 1. Please refer to the Control Panel manual and put the Control Panel into the learning

mode.

Step 2. Press & hold WTRVS ACTIVE/PENDANT button for 5 seconds. The WTRVS’s

Green LED will turn to Red. When hearing a long beep, release the WTRVS button.
The WTRVS is now in the learn mode.

Step 3. After 5 to 20 seconds, the Control Panel will display a message of WTRVS,

indicating the Control Panel receives a learn code form WTRVS. The WTRVS’s LED
will turn from Red, then blink green to steady green. Press the Ok button on the main
unit or configuration webpage to learn in WTRVS.

<<NNOOTTEE>>

Step 4. To check if the WTRVS is successfully learnt in, enable the Control Panel to get into

Step 5. Exit the Control Panel out of Learning Mode. The Learning process is now complete.

 It is prohibited to learn-in another or the same WTRVS twice, unless the previously

learnt WTRVS is removed first.

the Walk Test Mode first and press the WTRVS ACTIVE button. If you hear 6
continuous beeps from WTRVS and meanwhile the Control Panel responds a
ding-dong sound, showing WTRV message on LCD or configuration webpage
respectively. It indicates that the WTRVS is successfully learnt in. If not, the
learning process fails. Reset WTRVS first and then repeat Step 2 accordingly.

:

2