Temperature Sensor (TSO-9-EL-ZBS)
Introduction
O-9-EL-ZBS is wireless temperature sensor with attached temperature probe. It can automatically or
TTSSO
manually transmits temperature condition to the coordinator in the ZigBee Network.
The Temperature Sensor utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless
communication protocol that is reliable and has low power consumption and high transmission efficiency.
Based on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network
and coordinated for data exchange and signal transmission.
The Temperature Sensor serves as an end device in the ZigBee network. It can be included in the ZigBee
network to transmit signal upon activation, but cannot permit any other ZigBee device to join the network
through the Temperature Sensor.
Parts Identification
Remove the cover by loosening the bottom fixing screw, the inside of the Temperature Sensor will be
revealed as shown.
1. External Temperature Probe Terminal
Connect the External Temperature Probe to this Terminal
2. Tamper Switch
The Tamper switch will be activated when the Temperature
Sensor is removed from mounted surface.
3. Internal LED
Flashes – when the Learn Button is pressed.
Flashes twice – when successfully joined a ZigBee network.
Flashes once every 20 minutes – lost connection to its current
ZigBee network.
4. Learn Button
Press the button once to transmit a test / temperature signal to
the ZigBee coordinator.
Press and hold the button for 10 seconds then release to reset the Temperature Sensor.
5. Battery Compartment
6. External Temperature Probe
Connect the Probe to External Temperature Probe Terminal
Features
TTeemmppeerraattuurree DDeetteeccttiioonn
The Temperature Sensor will transmit temperature signals to the ZigBee coordinator in every 10
minutes regularly.
If Temperature Sensor fails to receive acknowledgment from the Control Panel, it means that
Temperature Sensor has lost connection to the ZigBee coordinator, please check you ZigBee
coordinator condition.
When the temperature changes by +/- 2˚C, the Temperature Sensor will also transmit a signal.
You can also press the Function Button once to transmit a temperature signal manually.
The temperature detection range is about -30°C ~ 100°C ( -22°F ~ 212°F).
BBaatttteerryy aanndd LLooww BBaatttteerryy DDeetteeccttiioonn
The Temperature Sensor uses one CR123 - 3V Lithium battery. Please always replace battery with
the correct size and voltage. When the Temperature Sensor is in low battery status, a low battery
signal will be sent to notify the user.
1
Battery Change
1. Remove the Cover by loosening the bottom fixing screw.
2. Remove the Old Battery.
3. Press the Tamper Switch or the Learn Button a few times.
4. Fit a new battery into the battery compartment. Please orient the battery according to the
correct polarity.
5. Replace the Cover.
TTaammppeerr PPrrootteeccttiioonn
The Tamper Protection is only active after power on the Temperature Sensor for 5 minutes.
The Temperature Sensor is protected by a tamper switch which is compressed against the
mounting surface when mounted. Whenever the Temperature Sensor is removed from mounted
location, the tamper switch will be activated and the Temperature Sensor will send a tamper
open signal to remind the user of the condition.
ZigBee Network Setup
ZZiiggBBeeee DDeevviiccee GGuuiiddeelliinnee
ZigBee is a wireless communication protocol that is reliable and has low power consumption and high
transmission efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount of
devices to be included in a network and coordinated for data exchange and signal transmission.
Due to the fundamental structure of ZigBee network, ZigBee device will actively seek and join network
after powering on. Since performing a task in connecting network may consume some power, it is
required to follow the instructions to avoid draining battery of a ZigBee device
- Ensure your ZigBee network router or coordinator is powered on before inserting battery into the
ZigBee device.
- Ensure the ZigBee network router or coordinator is powered on and within range while a ZigBee
device is in use.
- Do not remove a ZigBee device from the ZigBee network router or coordinator without removing the
battery from a ZigBee device.
JJooiinniinngg tthhee ZZiiggBBeeee NNeettwwoorrkk
As a ZigBee device, the Temperature Sensor needs to join a ZigBee network to transmit temperature
signal. Please follow the steps bellow to join the Temperature Sensor into the ZigBee network.
1. Insert the battery into the battery compartment to power on the Temperature Sensor
2. After powering up, press and hold the learn button for 10 seconds as the Siren resets and starts
searching for existing ZigBee network. Please make sure the permit-to-join feature on the router or
coordinator of your ZigBee network is enabled.
3. If the Temperature Sensor successfully joins a ZigBee network, the LED Indicator will flash twice to
confirm.
4. After joining the ZigBee network, the Temperature Sensor will be registered in the network
automatically. Please check your ZigBee coordinator, system control panel or CIE (Control and
Indicating Equipment) to confirm if joining and registration is successful.
5. After joining the ZigBee network, if the Temperature Sensor loses connection with current ZigBee
network, the LED will flash every 20 minutes to indicate. Please check your ZigBee network
condition and Temperature Sensor signal range to correct the situation.
FFaaccttoorryy RReesseett
If you want to remove the Temperature Sensor from current network and join a new network, you need
to use the Factory Reset function to clear the Temperature Sensor for its stored setting and information
first before it can join another network. To perform Factory Reset:
1. Press and hold the learn button for 10 seconds, release the button when the LED flashes once.
2. The Temperature Sensor has been reset to factory default setting with all its previous network
information removed. It will now actively search for available ZigBee network again and join the
network automatically.
3. If the Temperature Sensor successfully joins a ZigBee network, the LED Indicator will flash twice.
2
MMoouunnttiinngg MMeetthhooddss
There are two ways to mount the Temperature Sensor, by either Self-adhesive installation or Screw
mounting.
Self adhesive mounting
1. Clean the surface with a suitable degreaser.
2. Remove the protective covering from one side of the double-sided adhesive pad and firmly
apply to the back of the device.
3. Next remove the other cover and firmly press the item onto the desired location.
<<NNOOTTEE>>
UUssiinngg TTeemmppeerraattuurree SSeennssoorr wwiitthh ZZiiggBBeeee RRoouutteerr
Do not use the adhesive pad method of installation on a surface with peeling or cracked
paint, or on a rough surface.
Screw mounting
The Base has two knockouts, where the plastic is thinner, for mounting purpose.
To mount the Temperature Sensor
1. Remove the cover
2. Break through the knockouts on the base
3. Using the holes as a template, drill holes in the surface
4. Insert the wall plugs if fixing into plaster or brick
5. Screw the base into the wall plugs
6. Screw the cover back on to its base
IMPORTANT NOTE
If the Temperature Sensor installation location is away from your system control panel and requires
ZigBee routers to improve signal strength. DO NOT use a ZigBee Router without backup battery. A
ZigBee router without battery will be powered down during AC power failure and the Temperature
Sensor connected to the router will lose connection with ZigBee network. You should plan your
Temperature Sensor installation location using only ZigBee router with backup battery.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not
expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. (Example - use only shielded interface cables when
connecting to computer or peripheral devices).
3
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance
of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:(1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may cause
undesired operation.
Appendix
(The Appendix information is for developers only.)
TTeemmppeerraattuurree SSeennssoorr CClluusstteerr IIDD
Device ID: Temperature Sensor 0x0302
Endpoint: 0x01
Server Side Client Side
Mandatory
Basic (0x0000)
Identify(0x0003)
Temperature Measurement(0x0402)
Optional
IAS Zone(0x0500)
AAttttrriibbuuttee ooff BBaassiicc CClluusstteerr IInnffoorrmmaattiioonn
Identifier Name Type Range Access Default
0x0000
0x0001 ApplicationVersion
0x0003
0x0004
0x0005
0x0006
0x0007
0x0010
0x0011
ZCLVersion
HWVersion
ManufacturerName
ModelIdentifier
DateCode
PowerSource
LocationDescription
PhysicalEnvironment
Unsigned 8-bit
integer
Unsigned 8-bit
integer
Unsigned 8-bit
integer
Character
String
Character
String
Character
String
8-bit 0x00 –0xff
Character
String
8-bit 0x00 –0xff Read / 0x00 O
0x00 –0xff
0x00 –0xff
0x00 –0xff
0 – 32 bytes
0 – 32 bytes
0 – 16 bytes
0 – 32 bytes
Read
only
Read
only
Read
only
Read
only
Read
only
Read
only
Read
only
Read /
Write
None
None
Mandatory
/ Optional
0x01 M
0x00 O
0 O
Climax
Technology
(Model Version) O
M
O
O
O
4
Write
0x0012
Identifier Name Type Range Access Default
0x0000
Identifier Name Type Range Access Default
0x0000
0x0001
0x0002
0x0003
DeviceEnabled
AAttttrriibbuuttee ooff IIddeennttiiffyy CClluusstteerr IInnffoorrmmaattiioonn
IdentifyTime
AAttttrriibbuuttee ooff TTeemmppeerraattuurree MMeeaassuurreemmeenntt CClluusstteerr IInnffoorrmmaattiioonn
MeasuredValue
MinMeasuredValue
MaxMeasuredValue
Tolerance
Boolean 0x00 –0x01
Unsigned
16-bit integer
Signed 16-bit
Integer
Signed 16-bit
Integer
Signed 16-bit
Integer
Unsigned
16-bit Integer
0x00 –0xffff
MinMeasuredValue
MaxMeasuredValue
0x954d – 0x7ffe
0x954e – 0x7fff
0x0000 – 0x0800
Read /
Write
Read /
Write
Read
only
Read
only
Read
only
Read
only
0x01 M
0x0000 M
0x00 M to
-10 M
50 M
100(1%) O
Attribute of IAS Zone Cluster Information
Identifier Name Type Range Access Default
0x0000
0x0001
0x0002
0x0010
0x0011
ZoneState
ZoneType
ZoneStatus
IAS_CIE_ADDRESS
ZONE_ID
8-bit
Enumeration
16-bit
Enumeration
16-bit bitmap All
IEEE
ADDRESS
Unsigned
8-bit integer
All
All
Valid 64bit
IEEE address
All
Read
only
Read
only
Read
only
Read /
Write
Read
only
M
0x00
M
0x00 M
M
M
0xFF
Mandatory
/ Optional
Mandatory
/ Optional
Mandatory
/ Optional
5
Loading...