Climax Technology Co LS Users manual

ZigBee Light Switch: LS-1-ZBS(R) Series

Introduction

LS-1-ZBS(R) ZigBee Light Switch series include Master Light Switch and Slave Light Switch models.
Depending on the models selected, the light switch can be deployed in single or 3-way installation
according to requirement.

The Light Switch package is designed to be used in new installations or replace existing 3-way light
switch to achieve home automation. After joining ZigBee network, the Light Switch package can be
controlled via ZigBee network to activate remotely turn on/off household lighting.

The Master Light Switch utilizes ZigBee technology for wireless signal transmission. ZigBee is a
wireless communication protocol that is reliable, has low power consumption and has high transmission
efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to be
included in a network and coordinated for data exchange and signal transmission.

The Master Light Switch can also be bound to a ZigBee Controller to toggle On/Off the connected
lighting.

Models with router function (LS-1A-G-ZBSR and LS-1E-G-ZBSR) also serve as a router in the ZigBee
network. After being included in the ZigBee network, it allows other ZigBee device to join the network
through the Light Switch.

Caution

The devices are intended for installation in accordance with the local wiring regulations such as the
National Electric Code in the United States, the Canadian Electrical Code, or CSA C22.1, etc.. If you are
unsure or uncomfortable about installing this device, please consult a qualified electrician in your area.

Parts Identification

Master Light Switch: LS-1A/E-G-ZBS(R)

LS-1E-G-ZBS(R) LS-1A-G-ZBS®

1. Function Button

- Pressing the button to toggle on/off the switch.

- Press and hold the button for 10 seconds then release to reset the Light Switch.

- Press and hold the button for 3 seconds then release to bind with a controller

2. LED indicator

The LED indicator is used to indicate Light Switch status:

- On:
The Light Switch is turned off.

- Off:
The Light Switch is turned on.

- Flashes twice:
The Light Switch has successfully joined a ZigBee network.

- Flashes five times
The Light Switch has successfully bound with a controller

- Flashes every 20 minutes

1

The Light Switch has lost connection to its current ZigBee network (LS-1A-G-ZBS /
LS-1E-G-ZBS only)

- Flashing continuously
The Light Switch is overheated.

3. Air Gap Switch

- Pulled out:
Completely removes the power available to the load. This enables the connected lighting (bulb,

tube, etc.) that is controlled by the light switch to be changed with minimal danger of electrical
shock.

Use a flat-head screwdriver to pull the switch out.

- Pushed in:
For normal operation of the light switch.

Connection Terminals

Insert a flat-head screwdriver to open the clipper for each terminal and connect wiring. Remove the
screwdriver to close the clipper and hold wire in place.

4. Line Terminal

5. Load Terminal

6. Neutral Terminal

7. Travel Terminal

Master Light Switch: LS-1A/E-B (Rechargeable Battery)

LS-1E-B-ZBS LS-1A-B-ZBS

1. Function Button

- Pressing the button to toggle on/off the switch.

- Press and hold the button for 10 seconds then release to reset the Light Switch.

- Press and hold the button for 3 seconds then release to bind with a controller

2. LED indicator

The LED indicator is used to indicate Light Switch status:

- On:
The Light Switch is turned off.

- Off:
The Light Switch is turned on.

- Flashes twice:
The Light Switch has successfully joined a ZigBee network.

- Flashes five times
The Light Switch has successfully bound with a controller

- Flashes every 20 minutes
The Light Switch has lost connection to its current ZigBee network (LS-1A-B-ZBS only)

3. Air Gap Switch

- Pulled out:

2

Completely removes the power available to the load and charges the rechargeable battery of the
Light Switch. This enables the connected lighting (bulb, tube, etc.) that is controlled by the light
switch to be changed with minimal danger of electrical shock.

For the first time installation of LS-1A-B Light Switch, Air Gap Switch must be pulled out to
charge the rechargeable battery of the Light Switch.

Use a flat-head screwdriver to pull the switch out.

- Pushed in:
For normal operation of the light switch.

Connection Terminals

Insert a flat-head screwdriver to open the clipper for each terminal and connect wiring. Remove the
screwdriver to close the clipper and hold wire in place.

4. Line Terminal

5. Load Terminal

6. Travel Terminal (LS-1A-B-ZBS Only)

Slave Light Switch: LS-1A/E-S

1. Switch Button

- Pressing the button to toggle on/off the connected lighting.

2. LED indicator

The LED indicator is used to indicate Light Switch status:

- On:
The Light Switch is turned off.

- Off:
The Light Switch is turned on.

3. Air Gap Switch

- Pulled out:
Completely removes the power available to the load. This enables the connected lighting (bulb,

tube, etc.) that is controlled by the light switch to be changed with minimal danger of electrical
shock.

Use a flat-head screwdriver to pull the switch out.

- Pushed in:
For normal operation of the light switch.

Connection Terminals

Insert a minus screwdriver to open the clipper for each terminal
and connect wiring. Remove the screwdriver to close the clipper
and hold wire in place.

4. Line Terminal

5. Travel Terminal

Front Cover

A. Switch Cover

B. Light Switch Base

3