BX-15ZBS Outdoor Bellbox
Introduction
BX-15ZBS is a ZigBee Outdoor Bellbox. It is capable of raising alarm upon receiving alarm signal from
the coordinator in the ZigBee network when an alarm is activated. During the alarm, the Bellbox will
sound alarm with its built-in siren and also flash the strobe light to attract attention.
The Bellbox utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless
communication protocol that is reliable and has low power consumption an d high transmis sion efficiency.
Based on IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network
and coordinated for data exchange and signal transmission
The Bellbox serves as an end device in the ZigBee network. It can be include d in the ZigBee net work to
receive alarm signal, but cannot permit any other ZigBee device to join the network through the Bellbox.
Parts Identification
1. Mounting Holes x 4
2. Function Button
- Press the button once to send a supervision signal.
- Press and hold the button for 10 seconds then release to
reset the Bellbox.
3. Alarm Length Dip Switches
The Dip Switches contain 4 switches which can be set to
either ON or Off position
ON
OFF
4. Tamper Switch
The Tamper switch will be activated when the Bellbox is
removed from mounted surface, or it cover opened.
5. Battery Compartment
The Bellbox is powered by four 1.5V D-cell alkaline
battery.
6. LED Strobe Light
The strobe light includes 3 LEDs (From left to right: LED1-> LED2->
LED3)
Refer to below table for LED and siren beep for status indication.
Lost connection to current network LED3 flashes every 20 minutes
Joining ZigBee Network LED3 flashes twice
Arm 1 beep All 3 LED flash once
Home 3 beeps All 3 LED flash once
Disarm 2 beep Sequentially flash for 1 cycle
Arm (Tamper Fault) 5 beeps All 3 LED flash 5 times
Home (Tamper Fault) 5 beeps All 3 LED flash 5 times
Disarm (Tamper Fault) 5 beeps Sequentially flash for 5 cycles
Arm (Low Battery) 3 beeps All 3 LED flash 3 times
Home (Low Battery) 3 beeps All 3 LED flash 3 times
Disarm (Low Battery) 3 beeps Sequentially flash for 3 cycles
Burglar / Emergency Alarm Continuous alarm sound All 3 LED flash continuously
Fire Alarm
SSiirreenn AAuuddiioo
Alarm sound for 2 seconds,
followed by a stop of 1
second
SSttrroobbee lliigghhtt iinnddiiccaattiioonn
All 3 LED flash continuously
1
Features
z
z
AAllaarrmm AAccttiivvaattiioonn
When an alarm is activated, the Bellbox will activate its siren and strobe light according to different
alarm type:
z Burglar and Emergency alarm: Continuous alarm and strobe flash
z Fire alarm: 2-second alarm with1-second interval and continuous strobe flash
z
z
AAllaarrmm LLeennggtthh SSeettttiinngg
When the Bellbox receives an alarm signal via ZigBee network, it will activate siren and strobe
light according to the alarm length set by the system control panel.
If the Bellbox receives an alarm signal, but the alarm length duration is not defined by the system
control panel, the Bellbox will activate alarm according to Dip Switch setting below:
z
z
BBaatttteerryy aanndd LLooww BBaatttteerryy DDeetteeccttiioonn
The Bellbox uses four 1.5V alkaline D-cell batteries as its power source. The battery is included in
the package. Open the battery compartment then insert the batteries to power up the Bellbox.
The Bellbox features Low Battery Detection function. When the battery voltage is low, the Bellbox
will transmit Low Battery signal to the coordinator in ZigBee network.
When changing battery, after removing the old battery, press the Tamper Switch twice to fully
discharge before inserting new battery
z
z
TTaammppeerr PPrrootteeccttiioonn
The Bellbox is protected by a tamper switch which is compressed against the mounting surface
when mounted. Whenever the Bellbox is removed from mounted locatio n, or its cover opened, the
tamper switch will be activated and the Bellbox will send a tamper open signal t o remind the user of
the condition and activate an alarm immediately. The alarm length of tamper alarm is determined by
the Dip Switch setting above.
z
z
SSuuppeerrvviissiioonn
The Bellbox will transmit a supervision signal to report its condition regularly according to user
setting. The factory default interval is 30 minutes. The user can also press the Function Button
once to transmit a supervision signal manually.
SW1 SW2 SW3 SW4 Siren Duration
ON OFF
OFF ON
ON ON
OFF OFF
OFF OFF
OFF OFF
3 minutes
5 minutes
10 minutes
ZigBee Network Setup
z
z
ZZiiggBBeeee DDeevviiccee GGuuiiddeelliinnee
ZigBee is a wireless communication protocol that is reliable and has low power consumption and
high transmission efficiency. Based on IEEE802.15.4 standard, ZigBee allows a large amount of
devices to be included in a network and coordinated for data exchange and signal transmission.
Due to the fundamental structure of ZigBee network, ZigBee device will actively seek and join
network after powering on. Since performing a task in connecting network may consume some
power, it is required to follow the instructions to avoid draining battery of a ZigBee device
- Ensure your ZigBee network router or coordinator is powered on before inserting battery into the
ZigBee device.
- Ensure the ZigBee network router or coordinator is powered on and within range while a ZigBee
device is in use.
- Do not remove a ZigBee device from the ZigBee network router or coordinator without removing
the battery from a ZigBee device.
z
z
JJooiinniinngg tthhee ZZiiggBBeeee NNeettwwoorrkk
As a ZigBee device, the Bellbox needs to join a ZigBee network to send and receive alarm signal.
Please follow the steps bellow to join the Bellbox into the ZigBee network.
1. Insert the batteries.
2. Press and hold the function button for 10 seconds then release to join ZigBee network. Please
make sure to enable the permit-join feature on the router or coordinator of your ZigBee network
3. After joining the ZigBee network, the Bellbox will be registered in the security system in the
network automatically. Please check the security system control panel or CIE (Control and
Indicating Equipment) to confirm if joining and registration is successful.
2
4. After joining the ZigBee net work, if the Bellbox loses connection with current ZigBee network,
the LED 3 will flash every 20 minutes to indicate the situation. Please check your ZigBee
network condition and Bellbox signal transmission range to correct the problem.
z
z
FFaaccttoorryy RReesseett
If you want to remove the Bellbox from current network and join a new network, you n eed to use
the Factory Reset function to clear the Bellbox for its stored setting and actively search for a
ZigBee network. To perform Factory Reset:
1. Press and hold the function button for 10 seconds, then release the button.
2. The Bellbox has been reset to factory default setting with all its previous network information
removed. It will now actively search for available ZigBee network again and j oin the network
automatically.
3. If the Bellbox successfull y joins a ZigBee network, the LED3 will flash twice to indicate.
Installation
z
z
IInnssttaallllaattiioonn GGuuiiddeelliinnee
z The Bellbox is designed with a waterproof case to be mounted on e xternal wall of you house.
z When mounting the Bellbox, mount as high as possible for its siren and strobe light to attract
attention when an alarm is activated.
z The Bellbox is designed to be mounted on a flat surface with fixing screws and plugs provided.
z The base has 4 mounting holes for you to screw the Bellbox onto the wall.
z
z
MMoouunnttiinngg tthhee BBeellllbbooxx
1. Use the 4 mounting holes as template, drill holes on the wall.
2. Insert the wall plugs if fixi ng it into plaster or brick.
3. Screw the base into the wall plugs. Make sure the tamper switch is properly depressed
against the wall surface.
4. Screw the cover back onto its base.
z
z
UUssiinngg BBeellllbbooxx wwiitthh ZZiiggBBeeee RRoouutteerr
IMPORTANT NOTE
If the Bellbox installation location is away from your system control panel and requires ZigBee
routers to improve signal strength. DO NOT use a ZigBee Router without backup battery. A ZigBee
router without battery will be powered down during AC power failure and the Bellbox connected to
the router will lose connection with ZigBee network. You should plan your Bellbox installation
location using only ZigBee router with backup battery.
Appendix
(The Appendix information is for developers only.)
z
z
BBeellllbbooxx CClluusstteerr IIDD
Device ID: IAS Warning Device: 0x0403
Endpoint: 0x01
Server Side Client Side
Basic (0x0000)
Identify(0x0003)
IAS Zone(0x0500)
IAS WD(0x0502)
None None
z
z
AAttttrriibbuuttee ooff BBaassiicc CClluusstteerr IInnffoorrmmaattiioonn
Identifier Name Type Range Access Default
0x0000
0x0001
ZCLVersion
ApplicationVersion Unsigned 0x00 – Read 0x00 O
Unsigned
8-bit
integer
Mandatory
Optional
0x00 –0xff
3
None
Mandatory
/ Optional
Read
only
0x01 M
8-bit
0xff only
integer
Unsigned
0x0003
HWVersion
8-bit
0x00 –0xff
integer
0x0004
0x0005
0x0006
0x0007
0x0010
0x0011
0x0012
ManufacturerName
ModelIdentifier
DateCode
PowerSource
LocationDescription
PhysicalEnvironment
DeviceEnabled
z
z
AAttttrriibbuuttee ooff IIddeennttiiffyy CClluusstteerr IInnffoorrmmaattiioonn
Character
String
Character
String
Character
String
0 – 32 bytes
0 – 32 bytes
0 – 16 bytes
8-bit 0x00 –0xff
Character
String
0 – 32 bytes
8-bit 0x00 –0xff
Boolean 0x00 –0x01
Identifier Name Type Range Access Default
0x0000
IdentifyTime
z
z
AAttttrriibbuuttee ooff IIAASS ZZoonnee CClluusstteerr IInnffoorrmmaattiioonn
Unsigned
16-bit integer
0x00 –0xffff
Identifier Name Type Range Access Default
0x0001
0x0002
0x0003
0x0010
0x0011
ZoneState
ZoneType
ZoneStatus
IAS_CIE_ADDRESS
ZONE_ID
z
z
AAttttrriibbuuttee ooff IIAASS WWDD CClluusstteerr IInnffoorrmmaattiioonn
8-bit
Enumeration
8-bit
Enumeration
All
All
16-bit bitmap All
IEEE
ADDRESS
Unsigned
8-bit integer
Valid 64bit
IEEE address
All
Identifier Name Type Range Access Default
0x0000 MaxDuration
Unsigned
16-bit integer
0x00 –0xfffe
Read
Read
Read
Read
Read
Read /
Write
Read /
Write
Read /
Write
Read /
Write
Read
Read
Read
Read /
Read
Read /
only
only
only
only
only
only
only
only
Write
only
Write
0 O
Climax
Technology
(Model Version) O
M
O
0x00 O
0x01 M
Mandatory
/ Optional
0x0000 M
Mandatory
/ Optional
0x00 M
M
0x00 M
M
0xFF M
Mandatory
/ Optional
240 M
O
O
4
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority to operate this equipment.
(Example - use only shielded interface cables when connecting to computer or peripheral d evices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS-210
standard.. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
5
Loading...