Clifford TAZOR 4 User Manual

Stan dard Fea tures

The fol low ing are stan dard fea tures of this sys tem. Some ve hi cles may re quire op tional par ts/wir ing and a few are in com pati ble with some fea tures.

þ Lifetime warranty (see terms & conditions)

þ Two remote controls

n 100’ range (300’ with optional ElectroLoop Antenna) n ACG 2™ Anti-CodeGrabbing protection n Low remote control battery warning

þ PlainView 2™ coded valet mode

n Select your own secret code

þ Remote controlled valet mode

þ Starter interrupt

þ Dual-Zone Piezo Sensor detects both minor impacts and

theft-related tampering

þ Smart DataPort input

n For complete optional control of your system via your

Windows PC

n For smart accessory interfacing

þ Courtesy light(s) turn on when you disarm with the

remote

þ Remote panic feature

n Smart panic locking/unlocking based on whether the engine is

on/off

þ Built-in timer circuit for optional timed headlight

activation, window closure on some vehicles for a or turbo timer

þ Smart optional remote trunk release prevents falsing

þ Smart AutoTesting self-diagnostics

n With specific trigger & sensor identification

þ Malfunction AutoBypass

nAutomatic trigger remonitoring if trunk/hood was open when

arming

þ Smart Prior Intrusion Attempt Alert

n With specific trigger & sensor identification

þ FACT anti-false alarm circuitry

þ Passive AutoArming if you forget to arm with the remote

þ TotalRecall 8-event trigger/sensor memory report

n With specific trigger & sensor identification

control

n Lock upon AutoArming self-locking n Visual AutoArming countdown confirmation n Instant AutoArm bypass

þ High-Output Siren

n Remote controlled chirp muting n Long-term selectable chirp muting n Remote siren silencing without disarming if falsely triggered

þ Power door lock control (with built-in relays)

þ Ignition-switch controlled AutoLocking/AutoUnlocking

þ Built-in parking light flasher

Main te nance

Your Clifford system requires no maintenance except for periodic replacement of the remote control batteries. This product, like any electrical device in your vehicle, requires your car battery be in proper working order and fully charged. To ensure pro per operation, periodically have your vehicle battery “load-checked” at any local garage/mechanic. Also make sure the battery cables and connections are tight and free from corrosion.

þ Remote control code learning

þ Clear all remotes if ever lost or stolen

þ LED status indicator

n Flash indications reveal status n Automatic battery saving mode

þ Multiple vehicle control from the same remote control

þ Multiple sensor/trigger inputs

þ User-programmable features

n SecureAccess coded programming n Programmable even while driving

Wel come to the world of

high- technology ve hi cle se cu rity and con ven ience

ongratulations on the purchase of your Clifford Electronics mobile security/convenience system. Clifford Electronics has long been recognized as the leading manufacturer of high-technology vehicle security systems. Our commitment to technological innovation, quality and reliability is clearly evident

in your Clifford system. Yet despite all its sophistication, your system is amazingly easy to use, never more difficult than a few presses of a button.

Your re mote con trols

The two 4-button remote controls are sophisticated miniature radio transmitters each powered by a 3 -volt lithium battery. A weak remote control battery will reduce range (the system will warn you if the battery in your remote is nearing the end of its useful life, see the Low battery warning section for details). Electrical/radio frequency interference, obstructions, weather conditions, even sunspots can interr upt the signal from your remote to the system. The remotes are the keys to your system. But these remote controls are much more secure than car keys because e ach incorporates our ACG 2 (Anti-CodeGrabbing 2) technology for the ultimate protection against remote control cloning devices. You will use your Ta zor 4 remote control to arm and disarm the system, lock and unlock the doors, activate/deactivate the panic feature, enable/exit valet mode and comman d options such as a remote trunk release, power window control, electric garage door interface or even remote starting of the engine and heater or air conditioner, among other options.

Re motely con trol ling your Clif ford system

TO ARM:

TO DIS ARM:

TO ARM OR DIS ARM SI LENTLY:

TO PANIC:

TO RE MOTELY OPEN THE TRUNK:

TO RE MOTELY TURN ON HEADLIGHTS:

TO RE MOTELY START THE EN GINE:

TO TURN VALET MODE ON OR OFF:

TO RE MOTELY OPEN OR VENT WIN DOWS:

Press button . Upon arming: two siren chirps, two parking light flashes, dashboard LED flashes repeatedly and doo rs lock.

Press button . Upon disarming: one chirp, one parking light flash, LED turns off, doors unlock and the interior l ights turn on. Simultaneously press both the button and the ✱ button to arm or disarm without chirp acknowledgments.

For three seconds, continually press button . The parking lights will flash repeatedly and the siren will sound. If the ignition is on (indicating you are in the car), the doors will lock to prevent an assailant from entering (note: s ome vehicles are unable to lock the doors while the ignition is on). If the ignition is off, the doors unlock, letting you enter immediately without fumbling with your keys.

If you have this option, press button while the system is in its disarmed state.

If you have this option, press button to turn on the headlights for 10-seconds. If this button is set up as a turbo timer on your car, press it before turning off the ignition, then turn off the ignition, exit and remotely arm/lock. T he engine will idle for the duration set by your installer (1 second – 4 minutes) to cool the turbocharger, then shuts down the engine a nd brings the sensors online.

If you have this option, press button ✱ to remotely start the engine (or shut it down if idling under the control of IntelliStart 4). Before remote starting, be sure to see the Remote Engine Starting DOs and DON’Ts noted in the IntelliStart 4 user’s manual. Since remote control range is an issue with remote engine starting, you may want to consider the optional ElectroLoop Antenna option.

Simultaneously press buttons and ✱ to enable/exit valet mode.

If you have this option, press buttons and after disarming to fully open the windows controlled by SmartWindows 4. On hot days, press this button combination right after arming to vent the windows slightly while th e system remains armed.

ACG 2 (Anti- CodeGrabbing 2™)

ACG 2 protects you and your automobile from code-grabbing devices. Code-grabbers literally record, from hundreds of feet away, the code sent by your car alarm remote control (code-grabbers are very similar to, but simpler than, cellphone “cloning” devices). The thief then plays back the code when you’re gone, instantly disarming the alarm and unlocking the doors. It’s like leaving your keys and remote in the door. Many non-Clifford alarms can be defeated that easily, and some of the latest “smart” code-grabbers can even decipher the code hoppi ng/jumping sequence used by other car alarm manufacturers. In contrast, your Tazor 4 uses complex digital signal processing and unbreachable co de encryption to randomly change the digital code every time you use the remote control. Your remotes will never transmit the same code twice, and the control unit will never accept the same code twice. Thus the code played back by the code-grabber — even the latest generation smart code-grabbers — will never be accepted by your Tazor 4 system.

Re mote con trol bat tery re place ment

Replacement of the battery is simple, but any Authorized Clifford Dealer will be happy to do it for you provided you buy the replacement battery at their shop.

1. Insert a small, thin screwdriver blade in the slot near the keyring opening (you may leave the keyr ing in place) and turn it to separate the two halves.

2. Remove the old battery noting the + and – indications and replace it with the new one.

3. Put the enclosure back together by first aligning the top of the remote, then snapping the case bac k together at the bottom.

Auto matic re mote con trol low- battery warn ing

If your remote control battery is low, you’ll hear a rapid 5-chirp sequence when you disarm instead of the usual one chirp (with the Self-Powered SmartSiren 4 option, you’ll hear a low-pitched chirp). Replacement batteries are available from any Authorized Clifford Dealer.

+ 6 hidden pages